Search Documents

By S. Al-Thyabat

Conditioning of flotation feed is an important prerequisite for efficient flotation. This process depends on parameters such as conditioning time, slurry concentration and slurry pH. The objective of this paper is to optimize the conditioning process for the flotation feed. This was achieved by first conducting preliminary experiments at constant slurry pH to determine the significant ranges of slurry concentration and conditioning time. Then, factorial experimental design (32 experiments) was used to investigate the significance of the above parameters and their interactions on flotation recovery and grade. Statistical analyses using ANOVA approach showed that flotation recovery (R) and concentrate grade (g) were affected by feed conditioning. It was found that concentrate grade was linearly proportional to the slurry concentration and conditioning time, while flotation recovery was exponentially proportional to the conditioning parameters. A contour plot of the flotation response (recovery and grade) against conditioning parameters showed that the optimum operating parameters for flotation feed conditioning was a conditioning time of 1.5 to 2 minutes and a slurry conentration of 55% to 60%.

Jan 1, 2008

By Marlies Grimmer, Frank Amo Boateng

One of the challenges of mining is the concentration of heavy metals it releases into the environment through a phenomenon called Acid Mine Drainage. Freiberg is no exception due to its long mining activities. The European Union proposes that all rivers and streams must be in a good ecological status by the year 2027 but this would be difficult for large water sources as it would be economically unviable. Consequently, the approach of treating these waters at point sources would be of immense help and hence this column experiment on mine water treatment with carbon sorbents to remove zinc form the Rothschönberger Stolln. For this experiment three resins namely, APTsorb, activated coke, charred fermentation residues (which was produced by the Freiberg University of Mining and Technology) were analyzed through a simple column experiment to determine their sorption capacities. Through their sorption capacity as this experiment seeks to ascertain: we are able to make suggestions scientifically on the best material among the three for the future design of a treatment plant for the RSS. After the experiment whereby a 10 ml peri glass column was used, material A: APTsorb showed the least adsorption capacity (0.01 meq/g) and this could be attributed to the fact that the resin works well under pre-determined parameters such as pH and surface area. Material B: Activated coke showed a better sorption capacity (0.53 meq/g) in comparison to the basis value used for this experiment. Material C: charred fermentation residue which was produced by the University showed the most efficient capacity of (1.69 meq/g). This in comparison with the value used as the basis for this experiment showed that material C (charred fermentation residue) is very efficient for zinc sorption. pH values measured at the effluent of all the experiment were slightly higher than the pH measured in the initiating water.

Feb 1, 2024

By P. D. Chamberlain, R. M. Nadkarni, D. J. Kinneberg

Introduction The relationship between precious metal miners and gold refiners has been uneasy over the years. Reasons for this uneasiness and lack of trust include technical factors, economics of scale, and cultural differences. Technical factors take two forms. First, concentrates, precipitates, and sponge produced at the mine site are notoriously difficult to sample. A nonrepresentative sample can be the cause of misunderstanding and distrust. Dote, however, is relatively homogeneous and can be correctly sampled and analyzed with greater reliability. Second, the technology and chemistry of fine gold and silver production is complex and quite different from dote production. Most mining companies are content not to be involved with additional processing steps. From the standpoint of process economies, it is easy to see why miners and refiners are separate groups. Mine location is dictated by the natural occurrence of ore bodies. Heavy capital investment requirements for infrastructure in remote locations usually limits companies to produce the first marketable product from a mine. Beyond that point, the economies of scale and large capital investments for refineries generally dictate that the outputs of several mines be combined to feed a single refinery. The refin¬ing process is so complex that refineries are generally built in larger cities with a skilled labor pool. Therefore, only the largest mines can afford to refine their own output. Lastly, there are cultural differences between the miner and the refiner. The miner, particularly the small gold miner, is by definition a risk taker in a risky business. Refineries, on the other hand, have historically been operated under legal or implied monopolies approved by the government. The government is interested in owning gold, either for currency reasons or because many national mints are major users of gold coins. It is not surprising, then, to find that miners may regard refiners as part of an unresponsive government bureaucracy or, worse, as "city slickers." It is easy for the two groups to distrust each other with these different backgrounds. The interface between miner and refiner does exist and affects nearly all precious metal mining companies and most refineries. This paper discusses the technical and economic aspects of the interface. It points out how both parties can improve the relationship. Technical interface Precious metals selectively dissolve to produce a pregnant solution. They are then recovered from solution by zinc precipitation (Merrill-Crowe process) or by absorption onto activated carbon. This is followed by stripping and electrowinning. At this point, the mining company must decide whether to ship precipitates (or sponge) to refiners or to produce a dote. Some factors the company must consider are the ability to sample precipitates, concentrates or sponge, security of storage, and production rates. An important factor is the incremental cost (capital and operating) of converting precipitates or sponge into dote at the mine. Generally, mines prefer to melt precipitates or sponge to dote to avoid prob¬lems associated with sampling them. There are three types of fur¬naces used by mining operators to melt precipitates to dote. The first and most widely used is a sil¬icon carbide crucible heated ex¬ternally with a gaseous liquid fuel. The crucible is easy to use and slag can be skimmed before pouring dote. This simple system is capable of handling 1 t/a (32,000 oz per year) gold. It could cost as little as $20,000. More complex systems could cost up to $200,000. The second type of furnace is the gas- or propane-fired rever¬beratory furnace. This is usually used only by large-scale opera¬tors in the silver business. Precip¬itates in reverberatory furnaces come in direct contact with the flame. The large volumes of flue gas can carry significant amounts of dust and fume that must be re¬moved from the gas before dis¬charging it to the atmosphere. In the days when the Rand re¬finery in South Africa used reverberatory furnaces, the silver leaving the furnace in the form of vapor and fume was estimated at 2.2% of the total silver charged to the furnace. The gold in the gases was about 0.03% of the gold charged. Most of this silver and gold was recovered in the exhaust gas scrubber system. These scrub¬ber systems can be more costly than the furnace itself.

Jan 10, 1986

By J. D. Miller, C. L. Lin

Appropriate software and hardware necessary to adapt a x-ray CT analyzer for determination of coal washability has recently been developed and sucessfully tested for well characterized samples under laboratory conditions. Evaluation of the CT-based analyzer under simulated on-line conditions is also presented to verify the on-line capabilities of the newly developed x-ray CT analyzer for the control of coarse coal cleaning circuits. The investigation shows that the data obtained from CT washability analyses compare favorably with experimental sink-float data. Further, image frequency was considered to evaluate the CT-Based coal washability analyzer for simulated on-line conditions. Specifically the number of observations (image spacing) needed for accurate sampling and the total time required to perform the calculations for a representative data set were determined.

Jan 1, 2001

By C. C. Jobes, J. J. Sammarco, D. L. Anderson

Computer-aided control of a mining machine places its operator in a safe, remote location, thus reducing health and safety risks. Sensing systems that provide machine position (xy coordinates) and heading (yaw) are extremely useful in aiding remote positioning of mining machines. The US Bureau of Mines (Bureau) developed two sensing systems for position and heading information: a scanning laser system based on the Lasernet sensor and a mechanical position and heading system based on linear-position transducers. The Bureau is also investigating a system from Honeywell, the modular azimuth and positioning system (MAPS), that employs ring-laser gyroscopes (RLGs). This paper presents a brief background and status of these sensing systems as applied to a continuous mining machine (CM). Included are field test results off each system operating in a room-and-pillar research section at a cooperating West Virginia mine.

Jan 1, 1993

By T. Robyn

The Bolivar Cu-Zn skarn deposit in the Piedras Verdes mining district of Chihuahua is one of many base and precious metal deposits in the north-northwest trending Sierra Madre Belt extending across the states of Chihuahua, Durango and Sonora in northwestern Mexico. The information presented here is drawn from two papers on the Bolivar property1,4 plus new information. Historical mining and exploration for polymetallic Cu-Zn-Pb-Ag-Au deposits in the Sierra Madre Belt dates to Spanish Colonial days. Access to the Bolivar Property (Figure 1) is by paved road (approximately 305 km southwest from Chihuahua) and approximately 80 km by all-season gravel roads to the villages of Cieneguita (population ~1,000) and Piedras Verdes (population ~500) adjacent to the property. [ ] The Bolivar property comprises an old Cu-Zn producer (the Bolivar Mine), exploration concessions adjacent to the Bolivar Mine, and a new camp at the mine that supports mining, exploration and maintenance. From 1980 to 2000, former operators extracted approximately 300,000 tonnes of ore that was hand sorted to an average grade of 5-6% Cu and 25-30% Zn. From 2005-2010, Dia Bras produced from the mine just over 600,000 tonnes at an average grade of 1.7% Cu and 8.6% Zn. Dia Bras transported mineralized rock 275 km by truck and rail to its Malpaso mill, located about 30 km west of Cuauhtémoc in central Chihuahua, from 2005 until October 2011 when the new Piedras Verde mill was commissioned only 5 km from the mine. (Note: the Company cannot use the term ?ore? because it has never completed a feasibility study.)

Jan 1, 2012

By G. E. Jones, G. K. Hoffman

Through the USGS National Coal Availability pro-gram, two San Juan Basin studies have been completed. The study areas are in the northwest Bisti field, Fruitland Formation and in the eastern Standing Rock field, Menefee Formation. Original resources are 4.66 Gt and 3.46 Gt (5.14 billion stand 3.82 billion st), respectively, in the Bisti and Standing Rock areas. Bisti coal resources are greatly reduced by the Bisti-De-Na-Zin wilderness area (1.13 Gt (1.25 billion st)). Technological restrictions remove 31% from Standing Rock original resource. Available resources are 60% (2.79 Gt(3.07 billion st)) of the Bisti original resource and66% (2.26 Gt (2.49 billion st)) of the original Standing Rock resource.

Jan 1, 2000

By Ray E. Harris

Introduction A resource of more than 122 Gt (134 billion st) of minable trona and mixed trona and halite underlies an area of about 3400 km2 (1300 sq miles) west of Green River, WY (Culbertson, in preparation) (Fig. 1). In 1982, the total domestic consumption of soda ash (refined trona) was 6 Mt (6.7 million st) (Kostick, 1983). About 90% of this came from Wyoming trona. This enormous deposit occurs in the Wilkins Peak Member of the Green River Formation that is of Eocene age. This formation is derived from sediments deposited in a large lake named Gosiute. Lake Gosiute occupied the Green River Basin in southwestern Wyoming some 38 to 54 million years ago. The Wilkins Peak Member represents a restricted, evaporite-rich cycle of deposition when the trona deposits were formed. A total of 42 trona beds are known. Of these, 25 are of sufficient thickness and extent to be considered minable (Culbertson, in preparation). The production of sodium compounds from the trona deposits in the Wilkins Peak Member began in 1896 when wells were drilled within the present boundaries of the town of Green River. The purpose of the drilling was for extraction of sodium carbonate brines. Sodium carbonate (sal soda) was removed from these brines at a plant in Green River. Bedded trona was discovered in 1938 in a core from an oil well drilled south of Westvaco. In 1947, the underground mining of trona began. Production has continued from 1948 to date. Currently, five companies are mining trona and producing soda ash from the Wilkins Peak Member in Wyoming. Additionally, Allied Chemical Co. mines and processes trona for Church and Dwight's sodium bicarbonate (baking soda) operation in Green River. Competition in the soda ash industry depends primarily on the efficiency of mining and refining, allowing for lower-cost production. Newer plants and mine designs should increase efficiency. Solution mining holds promise as an even lower-cost method of mining. Employment in the soda ash industry is declining since the newer mining and refining methods are less labor intensive. Declines in employment, however, may be offset as production increases. Due to the large resource, the availability of minable trona should not be a problem for perhaps hundreds of years. Geology of Wyoming trona deposits Forty-two beds of trona or mixed trona and halite occur in the

Jan 10, 1985

By Donald R. Williamson

Statistical studies at Cyprus Pima Mine indicate that samples from 22 blastholes are necessary for determining average copper grades, within a desired range of precision, for mine-model blocks by arithmetic averaging. The average number of holes in such blocks is 14. Many considerations show that more holes will not be drilled for sampling. A way to determine block grades more reliably than by" arithmetic averaging was sought. Thus far arithmetic averaging has proven to be the best procedure for the particular operation characteristics despite the small number of samples. It naturally follows that expenditure of great effort in sampling blasthole cuttings is unwise.

Jan 1, 1977

By Ben Roderds

The Waneta Expansion Project (WAX) is located near the existing Waneta Dam site at the confluence of the Pend d?Oreille and Columbia rivers, approximately 10 km (6.2 miles) south of Trail, BC, Canada. The WAX owners consist of a partnership between Fortis Inc., Columbia Basin Trust and the Columbia Power Corp. This design-build project was awarded to SNC-Lavalin in late 2010 and is expected to be operational in mid-2015. The WAX consists of a new 335-MW powerhouse, including two new Francis turbine units, each generating approximately 167 MW. The powerhouse is located downstream of the existing Waneta Dam, and will make use of excess water that would otherwise be spilled during the runoff season. Water will be funneled to the turbines through an intake structure and two 10.5- m (34.5-ft) diameter, concrete-lined Penstock Tunnels. A 10-km (6.2-mile) transmission line will connect the powerhouse to existing electrical grids. Redpath/FKCI Waneta Tunnelers (RFK) was subcontracted by the heavy civil contractor, the Aecon/SNC Lavalin (ASL) joint venture, to excavate the two penstock tunnels and install the cast-in-place concrete liner. RFK is a joint venture partnership between J.S. Redpath Ltd., an underground mine contractor located in North Bay, Ontario, and Frontier-Kemper Constructors ULC, a heavy civil tunneling contractor based in Nova Scotia, Canada. Since penstock tunnel excavation was planned using drill-and-blast methods with a significant grade of more than 17 percent, the combined experience of these two contractors was a perfect match.

Mar 1, 2014

By V. Kecojevic

Environmental and economic costs related to equipment fuel consumption and carbon dioxide (CO2) emission present a substantial challenge to the mining industry. Haul trucks are an integral part of the overall surface mining system and they consume a significant quantity of fuel. Consequently, they produce a significant amount of CO2. The objective of this research is to (i) establish a mathematical relationship among a truck?s fuel consumption, power and engine load factors and (ii) determine the amount of a truck?s CO2 emission and the associated cost that may arise from potential CO2 legislation. In order to achieve these objectives, the authors have considered original equipment manufacturer (OEM) haul trucks, which are commonly used in surface mining operations. The research presented here may be used by mining professionals to help determine the cost and environmental burden of the trucks? application and efficiently manage energy consumption.

Jan 1, 2010

By R. E. Hamilton

Automation is a word whose meaning has been broadened by popular usage to include any labor saving device. We with restrict our usage to the replacement of human judgement by instrumental measurement and mathematical analysis in the control of industrial processes. Mineral concentration is an area which has resisted automation because of the great difficulty in developing measuring instruments which can exist in the rugged environment and can measure useful properties with acceptable accuracy. This is not the only factor limiting progress, but until recently it has been of over-whelming importance. The development of on-stream X-ray analysers, magnetic flowmeters and nuclear density meters for mineral slurries has eliminated this obvious barrier and is enabling us to locate and attack the less obvious problems which still limit our ability to automate concentrators. If we examine the history of automation in industries which are highly automated we find that it has usually gone through three distinct phases. The first phase has been regulation. This is the simplest form of control and involves manipulating some variable whose value is of no importance in order to maintain the value of some other variable which is important at a constant specified value in spite of disturbances which may occur in other variables which affect it. A simple example is the use of a control valve to maintain a constant flow of fluid in a line in spite of changes in pressure in the vessels at the ends of the line. The position of the valve stem is of no consequence, as long as it is within its operating range. Unfortunately we soon run out of variables which can be

Jan 1, 1971

By A. Bruynesteyn

The results of a 2 phase evaluation program designed to determine the amenability of an oxide ore from the Butte, Montana mine of the Anaconda Company to a sulfuric acid leach is presented. In the phase 1 preliminary evaluation, using roll tests and percolation leaching in small columns, it is shown that the ore is highly extractable at low acid consumption ratios. In the phase 2 confirmatory tests in large columns on l-l.5 tons of material, the amenability of the ore to the leaching process is proven and pregnant solution grade profiles from planned commercial heaps established.

Jan 1, 1978

By P. Conrad

Experience has shown that, since the passage of the Surface Mining Control and Reclamation Act, over-compaction of spoil during the reclamation process has severely limited tree growth on reclaimed land. Researchers at the University of Kentucky have conducted a ten-year investigation at a surface mine in eastern Kentucky that monitored the changes in selected spoil physical characteristics for various reclamation and compaction alleviation methods. More specifically, research plots were developed for reforestation that employed three different levels of compaction and two different methods of ripping for overly compacted spoil. Each year measurements were made in the field of dry bulk density, using a nuclear density gage, and maximum penetration depth, using a recording cone penetrometer. In addition to good correlation between tree growth and selected spoil characteristics, the data demonstrated a gradual convergence of the measured spoil characteristic data over the study period.

Jan 1, 2008

By Chunbao Sun, Qi Liu, Chao Wang

Entrainment is a process by which fine and ultrafine particles are transferred to the flotation froth from the top of the flotation pulp, and eventually discharge to the concentrate product, evenwhen they are not attached to gas bubbles. Therefore, entrainment can be considered as a two-step process, one at the upper layer of the pulp to the flotation froth, and the other from froth to the concentrate. Entrainment is inevitable for both hydrophobic and hydrophilic minerals and is one of the significant factors affecting concentrate grade. This paper provides a comprehensive review of the entrainment mechanisms and entrainment models, as well as a summary of the main factors affecting entrainment and the techniques thatmay be used to lower or eliminate entrainment. Based on the review, we point out that selective aggregation of fine and ultrafine gangue minerals using appropriate process aids (polymeric depressants, inorganic salts, etc.) to increase their particle sizes appears to be a convenient and economical method. Directions of further research along this line are discussed.

Aug 31, 2020

By C. Bachmann, M. J. Laurila, A. J. Widenman, A. Klein

Elemental analysis of slurry streams using X-ray fluorescence (XRF) has long been employed. However, detector technology has limited the application of XRF devices. Using detector technology employed on NASA's Mars Pathfinder to analyze soil samples, Process Control, Inc. has developed an on-line analyzer to mount on a sampling system. The prototype XRF elemental analyzer was installed at Detroit Edison's Monroe Power Plant in January, 1998 and has been employed to monitor feedstock quality. A slurry system has been developed for flotation control. This paper describes the testing of the analyzer using the new, draft ISO standard for evaluating the performance of online analyzers (ISO/DIS15239).

Jan 1, 1999

By David Harrison

Exxon Minerals Company uses geostatistical techniques for ore resource evaluation of its mineral projects. These techniques provide the most reliable estimates of recoverable tonnage and grade and uniform and realistic confidence limits. A schema has been developed which categorizes the company's successive evaluation phases. Clear separation is intended between geostatistical estimates and other factors in project evaluation such as mining, metallurgy, and economics. Company management seeks consistent and reliable estimates for investment decision-making and to meet growing demands for disclosure of mineral assets.

Jan 1, 1983

By W. Edwin Dill

For the mining industry, the Internal Revenue Code and regulations offer a range of choices in arriving at the allowable depletion. Each case is essentially unique. Two prerequisites can optimize these opportunities: communications between the mining company's tax specialists and its technical staff; and an understanding of IRS definitions. For the latter, a logical starting point is consideration of exploration and development, since they precede production and depletion is unallowable prior to production. Criteria for selecting engineering and accounting options for exploration and development indicate the necessity of interaction between these company functions to achieve the most favorable tax position.

Jan 1, 1982

By M. Ahrens

Gearless mill drives (GMD) are a well established solution for grinding applications in the minerals and mining industries. The paper describes the functionality and technical features of such drive systems as well as the development and the progress of GMD systems over the years. With an increasing installed base and many drives operating for many years, there is an increasing need to modernize or revamp existing GMD installations. The first installations of GMD took place in the cement industry and have demonstrated that ringmotors can achieve a lifetime well above 40 years, if maintained properly. The life cycle time of many other components, especially electronic parts, is usually shorter. It is therefore necessary to replace aged or out-dated components early enough in a planned manner in order to reduce the risk of component failures and the related shutdown times. Modernization upgrades can range from minor software updates to a revamp of the cycloconverter. The paper describes typical examples of such upgrades and shows the most important aspects that need to be considered.

Jan 1, 2008

The trend for using larger equipment in open pit mining to achieve cost effectiveness raises the question about the optimum economic point of scale in the current world of globalization. The present paper treats this question through the prism of a new methodology of assessing the impact of the size of production equipment on the economic outcomes of coal mining ventures. The methodology incorporates a production scheduling optimization model that implements both principles of mine planning, coal quality optimization and waste deferment. The implementation of the waste deferment principle dealing with the spatial and time aspects of the mine sequence arrangement allows the adequate modeling of the optimality of production equipment scale through the use of mine investment parameters, such as, purchase and ownership costs and discounted cash flows analysis. A case study is provided to illustrate the applicability of the new methodology.

Jan 1, 2004