Search Documents

By Edward J. Miller

Explosions and fires are without a doubt two of the most feared occurrences in modern underground mines. When they result in loss of life or substantial property damage, they usually gain world-wide media attention and have, on occasion, provided the impetus for legislative action. The very involvement of the Federal Government in mining was the result of a series of explosions which resulted in the loss of hundreds of lives. Fortunately, explosions of this magnitude are rare. Fires and explosions of lesser consequence are, however, more common and their severity may be more a matter of luck than anything else. The publicity which these events receive is usually restricted to the area immediately surrounding the mine and a1 though MSHA and sometimes the state prepare reports of their investigations, the general mining community is quite often aware of the circumstances surrounding these occurrences. This paper will discuss some of these "lesser" explosions which have occurred recently. These explosions have sometimes occurred in sealed or otherwise inaccessible areas of the mine involved, where conventional ignition sources such as electrical power were not present.

Jan 1, 1987

By James T. Furey, Laurence D. Hartzog, Graham A. Karklin

A pilot plant study was conducted to evaluate the performance of column flotation in the recovery of gold from the gold/tellurides bearing sulphide ore of the Kensington deposit (Echo Bay Mines and Coeur d'Alene Mines), and to compare the performance of column flotation to conventional "mechanically agitated" flotation, Tests were conducted in a 150 mm diameter, 60 liter glass column with ground flotation feed split from a concurrently operating conventional pilot plant, thus permitting direct comparison between the two processes. During the test program, the effects of wash water rate, gas holdup, froth depth, residence time and flow bias were examined in detail. The bulk metallurgical ore sample had an average "as tested" feed grade of about 5 git gold and 1 % sulphur, with the gold occurring primarily as inclusions of montbrayite (Au2Te3) in pyrite, with minor amounts of native gold. Conventional flotation using 60 minutes residence time across four roughing stages recovered about 97% of the gold into concentrates grading about 50 g/t Au. A single stage of column flotation roughing using 25 minutes residence time matched the conventional circuit recovery of97%, but produced grades of +150 git Au.

Jan 1, 1992

By Victor F. Hollister

Porphyry-type deposits are characterized by mineralization in, as well as adjacent to, an igneous body, usually a porphyritic stock. One deposit style includes both mineral dissemination and mineralized veinlets, and both porphyry copper and porphyry molybdenum deposits are characterized by dissemination and veinlet control of ore minerals. Those gold deposits that occur in stocks, with gold occur- ring in veinlets and disseminations within the stock, clearly are can- didates for consideration as porphyry gold type. Porphyry copper and porphyry molybdenum deposits are also characterized by potassic, phyllic, argillic, orpropyllitic alteration or some combination of these alteration types. Where two or more alteration zones are present, these are arranged in a sequential outcrop pattern. Gold occurring in dissemination and in veinlets in as well as adjacent to stocks, and which also occur in typical pervasive porphyry alteration suits, constitute a clearly defined class of deposit that fits the definition of a porphyry gold type. Porphyry copper deposits may carry appreciable gold. Porphyry copper-gold deposits are known from all porphyry copper provinces. This chapter is intended to cover porphyry gold occurrences that may have little or no copper or molybdenum as economic concentrations.

Jan 1, 1991

By Barry Cloutt

Western Mining Corporation Limited owns and operates the St Ives Gold Plant located near Kambalda, approximately 90 kilometres south of Kalgoorlie in Western Australia. Production commenced in March 1988 at a design capacity of approxi­mately two million tonnes per year. The plant was quickly expanded as a result of new ore discoveries in the district and has been processing ore since 1993 at the rate of three million tonnes per year. The plant has recovered over 50 tonnes of gold since the operation began, The plant was able to maintain acceptable recoveries throughout the plant expansion phases. Further gains in recovery were possible since there was still free gold in the tailings after approximately 24 hours of leaching. Testwork carried out on prospective orebodies showed that some contained considerable quantities of free visible gold, while others were seen to be semi­refractory using a conventional grind - leach circuit. Alternative treatment techniques were considered because a substantial amount of revenue was lost with the treatment of these ore bodies using conventional milling techniquies. The basis for all the investigations was to maximise the gold recovery from each orebody while minimising the effective cost per ounce of gold produced,

Jan 1, 1995

By Kathryn C. Sole, Angus Feather, Leslie J. Bryson

A novel solvent-extraction route for the production of high­purity gold has been successfully demonstrated on a pilot-plant scale, and the first full-scale production plant is being commissioned. This plant, at Harmony Gold Mine in South Africa, is designed to refine 24 tons of gold per annum when operated for one shift per day. The commercial implementation of this process represents not only a significant advance in gold­refining technology, but may also be instrumental in initiating important changes in the legislation regulating the marketing of gold in South Africa. The Minataur™ Process (Mintek Alternative Technology for Au Refining) is able to produce gold of either 99.99% or 99.999% purity from intermediate process products having a wide range of gold contents. The process comprises oxidative leaching of the feed material, followed by selective solvent extraction of the gold from the leach liquor to reject impurities, and then precipitation of high-purity gold powder. This paper introduces the process, presents selected results of pilot-plant trials in which high-purity gold was produced from two significantly different feed materials, and illustrates some of the applicable cost benefits.

Jan 1, 1997

By Kevin Stuffle, James E. Sharp, Sean Premeau

Two process enhancements for the biological oxidative pretreatment of sulfidic gold ore for subsequent treatment with cyanide are discussed. These are the use of a high areal density ring and pin packing (BioBalls™) as substrate, and the use of a novel biological ferric generator. The BioBall™ packing when coated with concentrates for heap leach processing offers higher areal densities, while leaving more open volume for fluid flow than more commonly used substrates such as aggregate. An oxidation rate study was performed on crushed auriferous arsenopyrite whole ore to demonstrate the benefits of using the packing. The auriferous arsenopyrite grading 2.9% Fe and .212 OPT gold was 50 percent oxidized in 24 days. The biological ferric generator is a passive air-side trickle bed reactor that efficiently converts ferrous to ferric in a process stream. Conversion rates of .8g/L h ferrous to ferric are routinely obtained. Although the biologically generated ferric solutions have not yet been tested on gold ores or concentrates, prior work has demonstrated that the high ferric solutions which will result in rapid oxidation of sulfidic gold ores or concentrates.

Jan 1, 1997

By Hans von Michaelis

The revolution in development of new technology and practices in the gold mining and metallurgy industry continues unabated despite the ups and downs in the gold price. Some of the new cutting edge technologies are listed in Table 1 overleaf. There is room to discuss just a few of these here, but many more are identified and described in RANDOL (1992). Cutting edge advancements in gold recuperation, can be sorted into three categories. The first category includes fundamental advances that offer major improvement with significant economic benefits. Second would include evolutionary developments that offer smaller, but nonetheless commercially valuable improvements. Finally there are those "advances" that are interesting but of trivial or question­able economic benefit to industry. It is essential to adopt a "systems approach" philosophy towards developing and applying new technology. Practical innovation often comes about as a result of having to solve a problem. Innovation for innovation sake is an ego trip. Environmental management has become an important part of the system and the environmental implications of new processes and practices in the mine and mill have to be carefully considered for potential benefits and/or liabilities.

Jan 1, 1993

By David J. Gurtler

In early 1988, Chino Mines Co. began using a system of economic splits for all materials encountered in mining. All mined material is evaluated as mill ore, solvent extraction electrowinning plant feed, and non-ore material, to determine its disposition. Results thus far indicate a significant increase in financial returns on material mined compared with the copper cutoff grade previously in use. Chino Mines is a partnership between Phelps Dodge Corp. (two-thirds ownership) and Mitsubishi Corp. (one-third ownership). The company produces copper and byproduct metals from the historic Santa Rita del Cobre mining district in southwestern New Mexico. The history of copper production in the district began with the use of surface native copper by native Americans before 1800. Spanish soldiers from Mexico later became aware of this district and mining began in 1801. The district was worked intermittently until 1909 when the Chino Copper Co. was formed, with Daniel C. Jackling as vice president and managing director. Concentrator operations were started in 1911. Kennecott purchased the company in 1933 and built a smelter in 1939. Chino Mines Co. was formed in 1980 when Mitsubishi purchased one-third of Kennecott's holding at the property.

Jan 1, 1990

By M. E. Hinkle

Concentrations of He, CO2, and O2 in soil gases were measured regularly for more than a year at a site near Golden, Colorado. Samples were collected from a hollow probe at 0.75-m depth and from a plastic hemisphere on the ground surface. Soil temperature, air temperature, percent humidity, And barometric pressure were also measured. Soil moisture was measured only indirectly as amount of rain or snowfall. Higher concentrations of CO2 in both the 0.75-m and surface samples correlated with higher soil and air temperatures, which suggests that CO2 was produced by bacteria. Lower concentrations of helium in both the 0.75-m and surface samples correlated with higher soil and air temperatures. Rain and snowfall appear to affect helium concentrations. Carbon dioxide concentrations were lowest when snow lay on the ground for extended periods of time. No correlation was seen between barometric pressure or percent humidity and concentrations of He, CO2, or O2 at 0.75-m depth or at the ground surface. No correlation, either positive or negative, was seen between concentrations of CO2 and O2.

Jan 1, 1988

By M. David Monroe

Getting the best match between truck and haul road requires examining the cost effects of many factors. Most mines use a bottom line measure based on cost per ton of material moved. This measure focuses on the two components of truck haulage cost per ton: productivity (or performance) and operating cost. For specific tasks, productivity can be measured or predicted using either field measurement or modeling. Individual tasks can be combined to provide a larger scale, longer term net figure for total mine output. True cost is more difficult to capture. Factors are time- and task-oriented and can be influenced by a summation of factors over a truck's lifetime. For example, "allocated" costs, such as owning (depreciation) and some repair costs, are spread over long periods. Items such as fuel and tires can be tied more directly to certain tasks. This article focuses on the more direct, task-oriented factors that affect truck productivity and cost. Major factors The relationship of haul roads and trucks means that each must be examined separately to isolate the most important factors affecting performance and cost. There are many factors but the most important are:

Jan 1, 1992

By Brian H. Zelenko, Patricia M. Perry

INTRODUCTION The environmental requirements of the next section of Washington, D.C. METRO subway tunnels present unique challenges to the Contractor. The 14th Street Tunnels contract includes twin 975 m (3200 linear ft) soft ground tunnels. A stringent environmental soil and groundwater monitoring and free product recovery program was specified by the owner. A project-wide dewatering program hinges on satisfactory completion of the environmental requirements. Implementation of the Contractor's environmental program is discussed, including the pros and cons of the program, as they relate to progress of the project. Environmental issues on tunneling projects have become an important part of the urban tunnel construction process. Delays associated with environmental issues can have a major cost impact on tunneling projects. This paper will discuss the first of five Washington Metropolitan Area Transit Authority (WMATA) tunnel and station contracts awarded in 1994. These contracts are part of WMATA's Fast Track Plan to complete the original 166 km (103 mile) system by 2001. As such, stringent environmental requirements have been specified as a part of these contracts to limit delays associated with local regulators in order that the tunnels may be constructed on schedule.

Jan 1, 1995

By John A. DesLauriers

INTRODUCTION This paper will update the status of small sized tunnel boring machines used in both the Mining and Civil Industries. I will mention a) new developments in small size hard ground tunnel boring machines, b) review North American performance records of the Atlas Copco Mini/Midi Fullfacers, and c) compare relative costs in driving a 1200m (4000 ft) typical utility tunnel using a leased TBM versus the conventional drill and blast method. NEW DEVELOPMENTS JARVA MACHINES Of all small rock tunnel boring machines currently in use, the Jarva MARK VI and MARK VIII are receiving the most enthusiastic acceptance. These circular fullface borers using usually 15 inch single disc cutters (manufactured also by Jarva) are designed on the 'T' bracing principle. Previously, Jarva's line of tunnel boring machines, even their smallest, was designed on the 'X' or double diagonal bracing configuration with a gripper in each quadrant. In small tunnels where net room is so very important, the 'T' scheme with gripping only at the spring line nets precious room around the cutter unit for passage of men and supplies. It allows freer un-

Jan 1, 1981

By K. A. Sauer

Blasting can create severe interference for a mine's carbon monoxide based fire detection system. At the present time, without being able to differentiate between blast and non-blast carbon monoxide, a fire detection system must either set fairly high alarm levels for its sensors, or allow frequent "false" alarms to sound during blasting. This paper will introduce current work being done which will attempt to define characteristics of the carbon monoxide concentrations time curve for blasting. The work uses drift blasting for its data base as it is one of the more common forms of blasting. Future work with the data may produce a mathematical model which can be used to monitor and identify the carbon monoxide time curve for drift blasting.

Jan 1, 1989

By David Shuck

On November 1991, Homestake Mining Co. completed the installation of a $5.7-million, 2.7-kt/d (3000-stpd) flotation circuit into the flowsheet of the McLaughlin Mine in California's coastal mountain range, about 113 km (70 miles) north of San Francisco. This addition reduced overall operating costs and improved the gold recovery of the low-grade refractory reserves over that expected from direct cyanidation. In addition, flotation provided a means to generate a sulfide concentrate that is used to supplement feed to the pressure oxidation circuit. The McLaughlin operation started in 1985 as the first pressure oxidation plant for treating sulfide refractory ore. During the mine's short history, efforts have been made to reduce costs and increase production through process development.

Jan 1, 1994

By G. S. P. Pereira, E. M. R. Santos

Acid mine drainage (AMD) is a serious environmental problem in mining activities. Prediction is the first step for evaluate the potential of acid generation and there are some possible methods to estimate it. They are described as static tests, which examine the balance between acid producing and acid consuming materials, and kinetic tests, which attempt to predict drainage quality overtime. Static methods are very simple and give a qualitative classification of the ores based on their potential to generate acid drainage. The characterization of ores to determine their acid producing potential is vital for the prevention of long term environmental liabilities. Laboratory tests were conducted under different methodologies to predict the acid producing potential of sulphide overburden, ore materials and tailings from a deposit of copper ore.

Jan 1, 1999

By A. M. Raichur, K. Keltner, M. Misra

The removal of oxyanions of arsenic present in mine process water and drinking water to a regulatory level (i.e. below 50 ppb) is a challenging problem. Conventional water treatment methods presently used for controlling arsenic have several drawbacks and limited success. A new adsorbent (LS™) developed at the University of Nevada, Reno, has strong specificity for both arsenate and arsenite species present in process waters. The adsorbent in very selective to oxyanions of arsenic and competition of other indifferent ions is minimum. Water samples from different sources were tested and arsenic was successfully removed to below 50 ppb. This paper describes both batch and packed column tests conducted in the laboratory as well as at the plant sites using LS™.

Jan 1, 1997

By Robert Stauffer, John Frostiak, Rein Raudsepp

Placer Dome's Campbell Red Lake Mine in Balmertown, Ontario produces a refractory gold flotation concentrate containing the sulphide minerals arsenopyrite, pyrite and pyrrhotite. In 1991, the existing concentrate roasters will be replaced with a pressure oxidation plant based on Sherritt Gordon technology to update the facilities and to satisfy environmental requirements. A successful continuous pressure oxidation miniplant program was conducted by Sherrill Gordon in late 1989 which formed the basis for the design of the commercial plant. The paper summarizes the Campbell operation and the environmental aspects of the project, and discusses the results of the miniplant program and the design of the commercial plant. The capital cost of the pressure oxidation plant and the process operating costs are also presented.

Jan 1, 1990

By Hans von Michaelis

This paper examines the process options available for treatment of "refractory" gold ores. As more and more of the easily leached oxidized gold ore zones are exhausted, the pressure is on to find more economical ways of treating refractory gold ore deposits. Historically, refractory ores were generally concentrated, e.g. to make a flotation concentrate that could be roasted. A major development is taking place in the USA in which ores from which gold cannot be concentrated well by flotation are being treated using whole ore oxidation processes prior to cyanidation. Refractory gold ore treatment processes are generally expensive to install and operate. Thus, for a refractory gold ore project to be economically viable, the grade must generally be higher than for free milling gold ores.

Jan 1, 1993

By C. A. Fleming, C. J. Ferron, P. T. O'Kane, D. B. Dreisinger

The platinum group metals (PGM's) are typically recovered by flotation, smelting of the flotation concentrate to matte, and matte leaching. Concentrates too low grade to be processed economically by the conventional process require a new treatment route. PLATSOL, a new pressure leach process, was developed for the Northmet deposit and dissolves in one step base and precious metals (PGM's and gold). Various options exist to recover all pay metals from the leach liquor. The preferred option to date involves a solid-liquid separation, followed by sulphide precipitation of gold and the PGM's, and copper solvent extraction using commercial solvent extractants. This paper briefly summarises the process and the effect of the main leach parameters. Application of the PLATSOL process to various feedstocks is also presented.

Jan 1, 2000

By J. H. Lammers, John Turney

The Eskay Creek Project was interesting in many respects, includ­ing extremely high grade of precious metals, refractory nature of the ore, carbonaceous content of ore resulting in preg robbing, and high content of many heavy metal sulfides in addition to the usual iron sulfides. Although the process plant was never constructed, extensive testwork was conducted and a flowsheet for the treat­ment of the effluent form pressure oxidation was developed as a basic engineering package. The flowsheet included removal of iron and gypsum by neutralization, selective recovery of copper by zinc precipitation, and recovery of zinc by solvent extraction and electrowinning. The zinc recovery produced a significant impact on the project economics. The waste water from the process met the environmental requirements for British Columbia.

Jan 1, 1996