Search Documents

When science and the human spirit come together amazing things can happen. This was perhaps never more evident than through the events that unfolded during August and October in a remote desert in northern Chile. On Aug. 5, the main shaft of the San José copper and gold mine near Copiapó in Chile?s Atacama Region collapsed, leaving 33 miners trapped more than 624 m (2,000 ft) beneath the earth?s surface.

Jan 1, 2010

By John C. Kleiber

From time to time since the initial installation of an experimental flotation section in 1940 (reference A), Permanente Cement Company has made efforts to beneficiate the low-grade limestone fraction which occurs in its deposit at Permanente, California, The encouraging results outlined in this paper are the result of Permanente's latest effort. This paper discusses the factors governing the selection of the flowsheet with particular reference to marketability of the sand tailing by-product. The process flow is outlined in detail, and operating statistics of the plant are presented. Finally, the problems encountered in the operation of Permanente's beneficiation plant are discussed as well as solutions sought and found.

Jan 1, 1964

By M. E. Ryan, C. L. Hoebbel, E. J. Haas

DISCLAIMER The findings and conclusions in this paper are those of the authors and do not necessarily represent the official position of the National Institute for Occupational Safety and Health, Centers for Disease Control and Prevention. Mention of any company or product does not imply endorsement does not constitute endorsement by NIOSH. ABSTRACT It has been suggested that effective disaster prevention and response in mining requires that elements of emergency management be incorporated into everyday operations, planning, and decision-making, much in the same way that the industry approaches routine risk management. Since Congress passed the MINER Act in 2006, the newly mandated structural and technological advancements in mine emergency response preparation have been made and are apparent, but measureable improvement in mineworker emergency preparedness is difficult to ascertain. To begin exploring whether measurable indicators of mine workforce preparedness can or should be addressed within a risk management framework, NIOSH researchers examined the datasets from two separate research efforts—one which measured the organizational safety climate and self-reported safety performance, and the other which measured individuals’ perceptions of their own self-escape competency. INTRODUCTION In response to the mine disasters in 2006, the United States Congress passed the Mine Improvement and New Emergency Response Act (MINER Act), which strengthened existing regulations [30 CFR, Part 48] and introduced new provisions to improve mine emergency response. Since that time, new technological and structural features, such as mandated redundant communication systems, personnel tracking systems, and lifelines in primary and secondary escapeways, have been installed in underground coal mines across the country. Additionally, mine operators are required to develop emergency response plans, provide adequate supplies of breathable air throughout the mine, provide more frequent and realistic expectations training, and are required to immediately notify the Mine Safety and Health Administration (MSHA) in the event of an accident. While the structural and technological advancements in emergency preparedness are readily observable and easily measured, levels of individual mineworker preparedness remain difficult to assess. There is a general consensus that deficiencies in competence in the non-routine tasks required for individual miners to effectively respond to a mine emergency likely remain (e.g., National Research Council [NRC], 2013), and NIOSH research continues address this concern (Haas, et al., 2015; Hoebbel et al., 2018). To maximize an operation’s capacity to effectively prevent disasters and/or respond to emergency events, it has been suggested that individual and emergency management efforts be incorporated into everyday operations, planning, and decision-making in much the same way organizations manage routine risks to health and safety (Haddow et al., 2017). To the authors’ knowledge, the mindful intersection of routine risk management policies and practices and emergency prevention and response readiness have yet to be empirically studied within the mining industry.

Jan 1, 2019

By L. Xinghua

Limonite is a general term for a group of amorphous iron oxide and iron hydroxide materials. It is considered as one of the very refractory iron ore types due to its wide variation in chemical composition, iron content, moisture content and easily sliming in the course of comminution. Iron grade of test sample is 25.48%, the iron minerals are mainly limonite; and the gangue minerals consist of quartz and feldspar in majority, secondarily silicate minerals. In this test work, high intensity magnetic separation (HIMS)-cationic reverse flotation and magnetic roasting-low intensity magnetic separation (LIMS) tests were conducted on limonite ore. The test results show that the concentrate with iron grade of 50.97% and recovery of 68.50% can be obtained by HIMS-cationic reverse flotation technique; while using magnetic roasting-LIMS technique, the better concentrate indexes of iron grade of 60.36% and recovery of 89.71% are achieved, and the iron grade of tailing is only 4.42%. Therefore, the magnetic roasting-LIMS technique is a better suitable method for beneficiation of low-grade limonite ore. Keywords: Low-grade limonite; Mineralogy; HIMS; Cationic reverse flotation; Magnetic roasting; LIMS

Feb 27, 2013

By S. E. Phillipson

The Mine Safety and Health Administration?s (MSHA) Roof Control Division (RCD) collects a variety of geological and engineering information pertaining to mining conditions in surface and underground mines throughout the United States. Recently, lineament analyses, trends of geologic structures, and inferred stress directions based on mapping at mines with problematic ground conditions, have been integrated into a GIS. The incorporation of different kinds of information into the same geographic coordinates and map projection, placed on digital geologic maps, allows site specific data to be evaluated in a regional geospatial context, identifying trends in the orientation of horizontal stress or patterns of structural geologic features. As more information is collected, the GIS will evolve as a tool for district- and basin-wide evaluations of controls on ground instability, and may evolve into a predictive tool for some kinds of geologic hazards. In addition to the geologic and geotechnical evaluations, the GIS also serves as a searchable database of previous mine investigations. The database can be searched for a variety of criteria, and the results displayed in real geographic coordinates to find the locations of previously visited mines or to evaluate mine fatality and injury data. This not only allows old reports to be found, but also places the information in a geospatial context with respect to neighboring mines or geographic areas. The GIS also has the capability to serve as a digital mine map repository, where maps can be stored in digital, georeferenced format for display in relation to each other and various themes of interest. This allows evaluation of multiple seam mining interactions and proximity to other mines, and on a national level could serve as an abandoned mine map database.

Jan 1, 2008

By Wayne Hilgedick

Peabody Coal Company is the nation's largest producer of coal and is headquartered in St. Louis, Missouri. In 1978 Peabody divisionalized its operations to establish more responsive and effective mine management. Peabody Coal Company's Arizona Division operates two large surface mines, the Black Mesa and Kayenta Mines. Both are located in northeastern Arizona, approximately 30 miles from Kayenta, Arizona, on the Navajo and Hopi Indian Reservations. The Black Mesa Mine produces 4 to 5 million tons of coal per year and the Kayenta Mine produces 7 to 8 million tons per year. Coal from the Black Mesa Mine is transported 274 miles by coal slurry pipeline to the Mohave Generating Plant located on the Nevada/Arizona border at Bullhead City, Arizona. This plant is jointly owned by Southern California Edison, the Los Angeles Department of Water and Power, Nevada Power Company and Salt River Project Agriculture Improvement and Power District.

Jan 1, 1983

By G. Norman Owen, Roger E. Scholl

INTRODUCTION The analysis and design of underground structures to resist vibratory motion due to earthquakes has been of interest to engineers for several decades. The dynamic stability of a powerhouse cavern was considered in the 1960s (Campbell and Dodd, 1967). About the same time, the designers of the San Francisco Bay Area Rapid Transit system developed procedures for analyzing the subaqueous tunnels placed under San Francisco Bay and the tunnels excavated along the land portions of the alignment (Kuesel, 1969). Japanese designers developed fairly sophisticated procedures for analyzing subaqueous tunnels during the late 1960s and early 1970s (Kuribayashi et al., 1974). In the past decade, proposals to site important critical underground facilities in regions with moderate to high seismic activity have increased the interest in earthquake engineering of underground structures. Seismic designs or seismic studies have been conducted for rock caverns for storage of petroleum or location of power plants (Yamahara et al., 1977; Glass, 1976), buried tanks for fuels or rad¬ioactive waste (Fukushima et al., 1977; URS/Blume, 1976), tunnels for disposal of nuclear waste (Yanev and Owen, 1978; Wahi et al., 1980), and urban mass transit tunnels (Monsees and Merrit, 1984). One of the greatest drivers of the interest in seismic analysis and design of underground structures has been the proposals to dispose of high-level nuclear waste in mined repositories some 300 to 600 m (approximately 1,000 to 2,000 ft) below the ground surface. In 1979, the authors, in conjunction with Professor Tor Brekke, presented a paper on an evaluation and design procedure used in a study of a proposed nuclear waste repository (Owen, Scholl, and Brekke, 1979).

Jan 1, 1985

By MEHMET KIZIL, PETER KNIGHTS, ROYAL REA

A 1/20 scale experimental dozer push test rig was designed and constructed to quantify the expected production rates (loose cubic metres per hour) for dozers operating in hard rock bulk push applications. The particle size distribution of the material employed in the test rig was modelled on a fragmented muckpile representative of that for a typical surface copper/gold mine overburden. A commercially available road base material was found to be highly representative of site conditions. Buckingham Pi theory was applied to mathematically develop factors for scaling up dozer productivity parameters, including blade loads and push times. Dozer production rates were investigated for various dozing distances and slope angles. A series of instantaneous productivity curves were produced which are applicable for use in hard rock dozer push operations. Currently, it is difficult to estimate dozer push productivity in hard rock environments due to dozer productivity correction factors that are empirical in nature and provide only discrete, end-point values for a range of operating conditions. The productivity curves produced demonstrate that dozer productivity declines rapidly over the range of 10 m to 40 m. As such, it is recommended that efficient bulk dozing operations in hard rock mining blocks should not exceed 40 m dozing distance. Further testing of muckpile conditions with increased clay and moisture content would be beneficial in order to better understand and quantify the effects of cohesion on hard rock dozer push productivity.

Nov 23, 2021

By H. Reed

The precious metal mining industry in Nevada handles and generates a certain amount of hazardous materials and waste on a regular basis. These products range from processing material additives to wastes from laboratory testing, heap leaching, and hydrocarbon treatment and disposal. The volume of materials and wastes is dependent upon the amount of ore processed. Handling, treatment and disposal is dependent on the type of material handled and the waste generated. Owing to the health and safety concerns and due to the existing regulations that control handling and disposal of hazardous materials and wastes, the mining industry is obligated to comply with all applicable requirements for proper handling of these products. Plus, in an effort to minimize any impacts from this effort, the industry is continually looking for alternative methods to accomplish these requirements and to also minimize costs. This paper will discuss the general, and in some cases the specific conditions, by which the industry is coping with the issue and efforts to minimize any impacts from handling, treatment and disposal for hazardous materials and wastes. The subject of compliance with the Toxic Release Inventory (TRI) requirements and bio-treatment of wastes and other technologies will be discussed.

Jan 1, 2001

By R. J. Nankee

Coal is our most abundant, low cost energy resource. Expansion of its use is being challenged due to "SO2 emission" regulation with even more restrictive legislation pending. High quality coal reserves are becoming more limited due to greater use in recent years. Aids to allow more use of coal in today's environment include beneficiation of coal before combustion and scrubbing the emissions from coal during combustion. Dow's efforts to help meet these challenges by beneficiating coal include true heavy media gravity separations with chlorinated solvents and liquid/liquid partitioning processes and "Dow Solvent Recovery Technology" to recover the solvent from product (or floats) and rejects (sinks), The objectives of the efforts to clean coal are to reduce sulfur and ash. In this paper, the solvents will be described; a general flow diagram presented; some of the results on upgrading various coals will be described, and projected costs of full-scale plants using chlorinated solvents will be compared to conventional cleaning plants.

Jan 1, 1985

By H. J. Bickel

This paper is concerned with general concepts and statistical devices used in projecting overall energy requirements. Particular emphasis is given to the use of individual end- use markets as an approach to developing future overall energy requirements, and translating these requirements into fuel consumption.

Jan 1, 1962

By J. Wright

Since the 1960’s toroidal conductivity has been used to determine the Alumina to Caustic ratio of the digester discharge liquor stream. In recent years the application of ceramic materials have allowed the sensors to moved upstream to provide tighter control of the process. In the Bayer process, dissolving the aluminum contained in bauxite ore in caustic soda and converting it to aluminum oxide produces alumina. An important parameter of the process is measuring the alumina to caustic ratio in the digester discharge stream. The A/C ratio at a given caustic concentration is a measure of the degree of saturation of the alumina in the plant liquor. The aim in the process is to achieve a high A/C ratio. There is however a limit where precipitation will occur if the A/C ratio is too high. For many years conductivity has been used to determine the A/C ratio. Conductivity of discharge liquor is related to the caustic concentration. The change in the caustic concentration is in the same direction of the change of solubility of the alumina. Controlling the conductivity through adding additional bauxite ore and varying the dilution flow can increase plant yield.

Jan 1, 2001

By Michael S. Moats, John Bailey Fletcher

Wear rates of grinding media can be misrepresented by marked ball wear tests (MBWT). Galvanic interactions between dissimilar grinding media can be affected by the chromium content in the media and the presence of oxygen in the environment. Corrosion, one component of wear, can be affected by many variables. Corrosion rates and corrosion potentials for modern high chromium white iron (HCWI) and high carbon steel (HCS) grinding media samples were obtained through electrochemical testing. In this study, the impact of chromium content in the grinding media and the dissolved oxygen in a simulated mill water solution on corrosion rates and potentials was examined. Increasing chromium content in HCWI above 15 weight percent increases the corrosion potential and decreases corrosion rate. Removing most of the oxygen from the solution lowers both the corrosion potential and corrosion rate of the materials tested. The electrochemical results were examined to model possible galvanic coupling effects on corrosion rates. Galvanic coupling between HCS and HCWI could cause differences in corrosion rates for almost all scenarios modeled. Based on the galvanic coupling analysis, MBWT results could be impacted by mixing HCWI and HCS in a ball mill charge. This impact is predicted to be more significant when dissolved oxygen is present in the mill water and as the chromium content of HCWI is above 15 weight percent.

Dec 21, 2022

By S. K. Kawatra, J. A. Halt

"Low-grade iron ores are finely ground and processed to recover iron-bearing minerals. However, the iron-rich powder is too fine to be used directly in blast furnaces and most direct reduction furnaces, and must be agglomerated or pelletized into a usable product called “pellets.” Bentonite clay has traditionally been used as a binder to make iron ore concentrate pellets, but it is expensive and contaminates the pellets. Organic binders may be a viable alternative to bentonite clay. This manuscript reviews organic materials that have been used to make iron ore concentrate pellets. Included are discussions on the development of organic binders, common pros and cons to organic binder use, organic binder structure and its effects on agglomeration, and additives to organic binders.IntroductionIron ore agglomeration turns finely disseminated, low-grade iron ores into a usable product, called pellets. During pellet production, fine-grained, iron-rich minerals are liberated from low-grade ores, concentrated, and agglomerated into round balls that are thermally hardened or cold-bonded to form pellets. Pellets are then transported to blast furnaces or direct reduction operations where they are used to produce iron; iron is further refined and shaped into the wide variety of steel-based industrial and consumer products in use today.Over the years, pellet production has become increasingly more prevalent with the increased exploitation of low-grade iron ores and increased iron and steel consumption around the world. In 2010, world iron ore pellet production was 388 Mt. It could be argued that the current pellet production process has been enabled by the use of binders – practical experience has shown that it would be nearly impossible to agglomerate iron ore concentrates using rotary drums and discs without using a binder."

Jan 1, 2015

By George A. Komadina

Pima Mining Company has recently completed their expansion tripling the plant capacity to 18,000 tons per day and now is in the process off expanding to 30,000 tons per day with completion scheduled for the summer of 1967. This paper briefly discusses the additions to the mining department and support areas with a more detailed report on the complete new crushing plant and additions to the concentrator. The crushing plant includes a 54-inch gyratory crusher, three 7-foot standard and seven 7-foot short head crushers along with necessary screens, feeders, and conveyor belts to produce a minus 1/2-inch rod mill feed. The concentrator consists of ten milling sections, each containing one 10-foot by 16-foot rod and two 10.5-foot by 13-foot ball mills, classification is done with cyclones. Pulp from each section is floated in 50 cells of 66-inch Fagergren flotation machines to produce a rougher concentrate which is cleaned in six stages of Denver cleaners to produce a final concentrate The various mill products are thickened with disposal made in conventional manner. Plant instrumentation is discussed in the paper.

Jan 1, 1967

By Christy Z. Lueders

Introduction More and more women engineers are joining the traditionally male mining industry. Are they successful? Do they encounter special problems? How do men in mining respond? How can the mining industry effectively use its female resources? What contributes to the success of a woman in mining? What can male engineers do to ease the entry of female professionals into the workforce? An STM survey conducted last spring provided some answers to these questions. All BS graduates in mining, mineral engineering, and extractive metallurgy from 1960-1979 were surveyed. Nearly 60% of the female graduates, from 17 universities, completed questionnaires. The women were asked why they chose mining, how they relate to predominantly male co-workers, what job skills they have gained, and what areas of work they most enjoy. They were also asked how problems of a two-career family are solved. Data were gathered on salaries, titles, specialties, and products handled. Respondents, assured of confidentiality, are identified only by title. Many male mining executives were also questioned for their advice to women in mining. Profile of the Survey Participant The "typical" female mining engineer works with coal, is employed by an operating company, feels she works very hard to prove her abilities, does not want to be treated as an anomaly, and someday wants to be an independent consultant. Of the respondents, 44% listed coal as the most familiar product, 12% said copper, and the rest listed products from industrial chemicals to oil. Titles varied widely but women managers are rarely found. However, the majority of the survey population graduated after 1976 and thus lacks substantial experience. Of 102 female graduates, only 25 graduated before 1977. Since then, there has been a steady increase. The American Association of Engineering Societies reported that in 1980 more than 100 degrees were awarded to women in minerals engineering. Education Highly Valued Twenty-two percent of the women surveyed had graduate degrees, 38% planned further education, and 12% listed a PhD as their goal. The majority of graduate degrees are in technical fields. There were only two MBAs. Five women intended to pursue law degrees, and one woman, with a mining engineering degree and an MBA, is a part-time law student. Along with advanced education, the women agree that production experience is needed for career advancement. However, only 28% of the women have worked in production. Many women, especially younger grads, commented that these are the toughest jobs to get. This is a universal complaint, from males as well as females, though women seem to encounter more opposition. Several women mentioned they were small or slight of build and managers tended to shy away from hiring them for production jobs. Two-Career Marriages The most difficult problem for two-career couples is relocation. Whose career takes priority? Fifty percent of the women said transfers or offers would be examined on a case-by-case basis, weighing pros and cons for both parties. The husband's career took priority with 47% of the women; their own careers, with 3%. These statistics conflict with comments from two employee relations managers. Both said most female engineers they've encountered are married to men who follow their wives' careers. Seventy per cent of the married respondents said their husbands were also engineers. Four said their husbands were engineers at the same company. Some male and female engineers met on the job; others joined the company as a "package deal." Both partners being engineers can ease relocation problems, since an area or company offering one spouse a job can often provide a spot for the other. A company may benefit by getting two new hires for the relocation costs of one. Most companies contacted have policies that allow married couples to work at the same division, but discouraged them from working in the same department. With 40% of today's marriages ending in divorce, one risk is that one or both parties may quit. One personnel executive said there were several couples, each spouse in a different discipline, who were work¬ing out very well at his division. However, he recognized the potential for problems if, for instance, one gets promoted and the other doesn't, or salary increases are unequal. The personnel executive said he has actively recruited married couples, and would again, were each person competent.

Jan 10, 1981

By Joseph W. Murray

Prior to 1950 Magma's ore production came from two parallel, steeply dipping, east-west striking mineralized faults, one called the Main or Magma vein, and the other the Koerner vein, which lay about 1100 feet to the south, This vein system has been explored and mined over 9000 feet horizontally and 4800 vertically. In 1950 continued exploration led to the discovery and subsequent development of replacement ore bodies in the Devonian limestone zones adjacent to the veins. These replacement deposits occur in the eastern part of the Magma Mine, and follow the strike and the 30" east dip of the host limestone. Strike length of the ore bodies varies from 250 to 500 ft., and thickness from 15 to 125 ft. The ore bodies are large tabular masses with chalcopyrite and bornite being the dominant ore minerals. Hematite and pyrite are the most abundant gangue minerals. Incompetent limestone, shale, or a porphyry sill hanging wall is charactertistic of substantial portions of the replacement beds. In many instances the ore itself is blocky, badly fractured, and intermixed with layers of limestone gouge, pyrite and hematite.

Jan 1, 1973

By III Feeley

Coal is the nation's most abundant fossil energy resource and serves as the primary fuel for the U.S. electric-power industry. However, its continued and expanded use is often challenged by the nature and amount of its associated impurities, such as mineral matter, sulfur, and trace elements. The moderate- to high-sulfur content of many U.S. coals is of particular concern today as potentially more stringent regulations requiring further reductions in sulfur dioxide emissions are being considered. The most prevalent method currently employed to control SO2 emissions from coal-burning facilities is post-combustion flue-gas desulfurization. However, physical coal cleaning (a.k.a. beneficiation, preparation) methods can also be effective in removing sulfur and ash impurities from coal prior to combustion. In a typical physical cleaning operation, raw coal is crushed to about 50-mm (2-inch) topsize, and then screened into coarse, intermediate, and fine size fractions. Crushing liberates some of the ash-forming minerals, including the portion of inorganic sulfur (pyritic) not chemically bound to the coal matrix. The percentage of impurities liberated generally increases as the coal particle size is reduced. Coarse- and intermediate-sized coal particles are typically subjected to specific gravity-based cleaning methods, while fine-sized (less than 0.5-mm) coal particles are beneficiated using froth flotation, a technique based on surface property differences. Greater cleaning potential exists at finer sizes because of increased liberation of impurities, but this potential is not fully realized because of inefficiencies associated with fine particle separation using state-of-the-art coal cleaning technologies.

Jan 1, 1990

By Robert L. Marovelli

The major mining health and safety problems of concern to United States Government and private industry researchers in 1981 included the difficulty experienced by longwall operators in complying with the Federal 2 .0-mg/m3 respirable dust standard, the accident rate associated with falls of ground and materials handling hazards, and the upsurge in the incidence of disasters after the steady decline in recent years. Although the many mines and manufacturing companies involved in the research projects to be described are not specifically identified, it is important to note their significant involvement. This is not by way of acknowledgement, but rather to establish that these projects, using mostly Federal funds, represent close cooperation between the U.S. Government and the mining industry. The ongoing work to be described on the development of critical longwall dust control technology is a classic example of Government-industry participation through the phases of problem identification, planning, cost-sharing, and implement at ion.

Jan 1, 1982

By T. J. Close

On September 10, 1991, Secretary of the Department of Interior Manuel Lujan deleted the Silver Peak Range North Wilderness Study Area from the list of U.S. Bureau of Land Management lands in Nevada to be considered for wilderness designation. This decision was based in part on the U.S. Bureau of Mines mineral investigation of the wilderness study area which found that it has indications of precious metals resources. The following is a summary of the results of that mineral investigation. The study area lies between the Silver Peak and Dyer mining districts of west-central Nevada. The Silver Peak mining district, to the east, has a long mining history dating back to 1907 when precious-metals-bearing veins were discovered. The major producer in the Silver Peak district was Sunshine Mining Company's Sixteen-to-One silver mine. During the Bureau's study the Sixteen-to-One mine was operating; it has since been idled due to low silver prices. Precious metals-bearing veins were discovered in the Dyer district, to the west of the study area, in the 1860's. Mineral activity in Dyer district consisted mainly of prospecting. The Silver Peak study area itself has no mining history and contains only a few mining claims, but the Bureau examined 13 mineralized sites, most previously unknown and unclaimed. These sites are along two zones that cross the study area from the Silver Peak to the Dyer mining district. The two zones transect a volcanic center of fractured and altered rocks that contain epithermal veins of quartz, calcite, and jasperoid with gold, silver, and base metals. At the surface these veins are poorly defined and poorly mineralized. The more than forty veins examined in the study area are as thick as 17 feet and as long as 1,000 feet. Samples from surface exposures of these veins contained as much as 0.02 ounce per ton gold, 2.1 ounces per ton silver, 1.0 percent copper, 2.6 percent lead, and 0.4 percent zinc. Analyses of the Bureau data disclosed no vein large enough or of high enough grade to be classified a mineral resource. However, most do have indications of silver-and gold-bearing resources at depth. Subsurface exploration had to be done on the vein at the Sixteen-to-One mine to outline reserves (a vein averaging about 22 feet thick and containing 6-to 7-ounces per ton silver); the same is true of veins in the Silver Peak Range North Wilderness Study Area.

Jan 1, 1993