Search Documents

By Stuart R. Cotterill, Jack D. Nelmark

Introduction Opencast surface mining requires blasthole drilling to achieve mine planning. No single method of mining is right for all conditions. Occasionally, mine planners introduce a project with little regard to drilling and blasting. These costs are usually a significant percentage of total mine overhead. One drilling and blasting method that can be used to reduce overall mine expense is inclined or angle hole drilling. But inclined-hole drilling will not cut costs unless a set of required circumstances is met. Several conditions of mine design indicate the use of angle drilling. Geotechnical problems must first be analyzed. Primary considerations are safety, fragmentation, production, and maintenance. Secondary considerations are, in some instances, reduction in amount of explosives, which lowers blasting costs; reduction of practical fragmentation beyond blasting pattern limits; and reductions in overall costs due to reduced volume of excavation. Future trends in blasthole drilling may include incorporation of drill equipment designed to allow rapid change from vertical to inclined drilling. This will allow the operator to adapt to changing hole requirements with minimal production loss. Another improvement may be the ability to chamber holes at any elevation throughout the hole depth. This will allow more charge to be placed at strategic locations to improve fragmentation. Merits of Drilling Inclined Holes Drilling is performed to create voids for explosives. It is done either to recover minerals or to excavate a volume of earth. The manner of mining or excavation can greatly affect the economics of the overall project. Many innovations and methods have been tried, but the most practical and economical is still drilling holes and using explosives to fragment the material. To break up the material, the practice has been to place charges within the mass. This is done by drilling holes of a specific diameter and depth into the material. The holes are of such magnitude as to develop sufficient energy to break or loosen this material, providing for easier removal. In general, more open or exposed faces must exist to aid material breakage when blasting. Inclined drilling can be advantageous in open-cut mining with highwall depths of at least 24 m (80 ft). A minimum of two faces are open in open-cut mining and the material can be thrown outward to cover pre-mined volume. This cuts cost by eliminating the need to remove or relocate a large portion of material. Sometimes the material is of such a mass that more energy per unit is required to loosen it than can easily be done by blasting vertically. Inclined holes allow a more uniform loading of drilled holes. The unit of energy is raised, so little or no secondary blasting is required. This usually comes about only if the main plan calls for drilling holes deeper than 24 m (80 ft). For shallow holes, spacing and burden can be made closer to allow sufficient energy to blast the toe. If the open face is in only one

Jan 9, 1984

By W. A. Crosby, A. Bauer

The recent increase in size of open-pit mining operations has resulted in major improvements in efficiency that are beneficial to the mining industry. Higher bench heights, larger diameter blast-holes, and more powerful explosives have played an important part in reducing mining costs. These measures have, however, resulted in increased energy concentrations in the blast area, which can result in severe backbreak problems for final pit walls. If backbreak is not controlled, a decrease in the overall pit slope angle will ultimately be necessary, and consequences, such as decreased recoverable ore reserves and increased waste-to-ore ratios, will result. Greater amounts of loose face rock will be produced, and planned safety berms will be less effective or nonexistent. Hazardous working conditions can also result. Remedial measures, such as scaling large areas and using wire mesh or other artificial support, are very expensive and difficult to implement. There must be a trade-off between the money saved by using larger blasts, and the time spent to maintain pit wall quality. The best approach is to control blasting effects so the inherent strength of pit walls is not destroyed. Presplit and trim blasting are two control blasting techniques used to accomplish this. Both techniques are designed to create a low explosive energy concentration per unit of wall area at the perimeter of the pit. Energy concentration of the main production blast must also be controlled to avoid damaging the final pit wall. A low-energy concentration at the final wall can be obtained by decoupling charges, decking charges, using less powerful explosives, decreasing blasthole diameters, and changing the burden and spacing. Rock properties-fragmentation and the final state of the pit wall-influence the success of a blast. The most important properties to consider are: in situ rock strength, and the nature, frequency, and orientation of structural features. Since these variables cannot be controlled, they must be evaluated by suitable field tests, and then a control blast can be designed using controllable variables, such as spacing, burden, and hole diameter, so the blast will be successful for appropriate rock conditions. One main thrust of this article is to show how control blasts can be successfully designed for larger hole sizes, up to 381-mm-diam. While efforts to produce a good control blast in shovel/truck pits have been ongoing for some time, recent use of a modified presplit technique in dragline operations has helped reduce water problems, improve safety, and increase dragline productivity in a number of surface coal mines. This article presents examples on designing and using presplit and trim blasting for large hole operations in both shovel/truck and dragline mines. Presplit Blasting As introduction to presplit blasting, Fig. 1 illustrates a typical presplit blast layout using 102 mm-diam presplit holes for 381¬mm-diam production holes. For this type of blast, presplit holes would normally be drilled first, ahead of main production holes. The choice can then be made between loading and firing the presplit line or infilling the main blast. In the latter case, the presplit line would be fired instantaneously 100-150 milliseconds before the main blast. As shown in the figure, the presplit line is formed ahead of the main

Jan 2, 1982

By Charles Morris, Patricia Petty

Charles Morris Minerals engineers have a new opportunity to shape their industry's future. They can help secondary school teachers in their own communities improve their scientific knowledge and thus be better prepared to teach their students. Local sections of AIME and other groups are being asked to sponsor expense-aid scholarships for teachers who complete the summer field course A Total Concept of the Mining Industry. Now in its 18th year, the six-week summer course is presented by the Colorado Mining Association Education Foundation Inc., in cooperation with the Colorado School of Mines Office of Special Programs Continuing Education. The course will be held June 9 through July 18. "In the past, we have been successful in soliciting support for teacher-scholars from many organizations, corporations, and individuals within the industry," said John Robertson, Jr., Foundation chairman. "Now we hope to enlist the help of engineers at the grass roots level in identifying qualified local teachers and giving them what it takes to participate in this continuing education program." Robertson said the course provides secondary school teachers, counselors, and administrators with a working knowledge of the mining and metallurgical industries. It also helps teachers recognize career opportunities for their students. "With the industry facing a challenging new era, we must have teachers who can relate the excitement of this challenge to their students. They will inspire future generations of resource finders, developers, and managers," he said. More than 670 teachers in 27 states, including 45 graduates of the "class of '85" have completed the course and gained six semester hours of graduate credit. The Foundation's Planning and Curriculum Committee meets regularly to develop the course outline and recruit the faculty. Lecturers are selected on their ability to communicate with people not familiar with the industry. Last year, 67 faculty members came at their own time and expense to discuss their specialties, ranging from exploration to marketing. Normally, teachers receive scholarship aid in the form of tuition and fees, and transportation and meals while on field trips. Expense-aid scholarships cover room and board on campus for those beyond the Denver-Metro area, and travel to and from Golden. "We hope to broaden the appeal and the geographical range of the program," Robertson said. Inspiration for the field summer program for teachers came in 1967 from a mining engineer, the late C.L. (Lindy) Barker, a 1931 graduate of the Colorado School of Mines. Barker and a group of concerned individuals convinced the Colorado Mining Association to accept sponsorship of the course in 1968. The Colorado School of Mines and its Office of Special Programs and Continuing Education agreed to be a co-sponsor to give it accreditation and provide physical facilities and coordination. The first course was held in 1969. Operating funds were solicited from industry to pay tuition, course material, the cost of a course coordinator, field trips, and overhead. Through the years, personal contact by an industry representative has been the most effective teacher recruiting tool. Through expense-aid scholarships provided by local sections of professional organizations, such as AIME, as well as CSM alumni and other friends, there will now be a greater incentive for more teachers to get to know the minerals industry and pass that knowledge on in the classroom.

Jan 3, 1986

By Keith P. Bingham

A total transportation system providing for delivery of finished products to customers and raw materials to the plant is one of the key elements contributing to Dravo Lime Co.'s success. Dravo Lime operates one of the largest noncaptive lime and limestone plants in the US at Maysville, KY, where products produced can cost as much to deliver as they do to manufacture, depending on the product itself, its destination, and mode of transportation. With delivery costs comprising a significant portion of total costs for its products, Dravo Lime has made total transportation services an integral part of its business strategy. Prices for most products produced at Maysville are quoted f.o.b. destination. In short, Dravo Lime's Distribution Department relies on the approach that says to customers: "Leave the delivery to us." The 0.9-Mt/a (1-million stpy) Maysville facility, located about 121 km (75 miles) east of Cincinnati, OH, on the Ohio River, primarily produces sulfur-absorbing Thiosorbic lime used by coal-fired electric utilities as a scrubber reagent to remove SO2 from stack gases. The product is currently supplied to eight power plants in the Ohio River valley region which extends through portions of Kentucky, Indiana, Ohio, West Virginia, and Pennsylvania. The plant ships approximately 907 kt (1 million st) of lime and a comparable amount of limestone fines each year. In addition, it arranges for delivery of about 181 kt (200,000 st) of coal to the plant. Lime is transported by covered hopper barges, covered rail cars, covered dump trucks, and pneumatic trucks. It is transferred from barges to storage silos and trucks at a terminal on the Ohio River near Marietta, OH. At another terminal near Aliquippa, PA, lime is transferred from barges to silos, trucks, and rail cars. Future plans call for rail-truck transfer terminals. To produce lime from limestone at the Maysville plant, about 181 kt (200,000 st) of coal is burned annually in three coal-fired kilns. In transporting this coal from the mine to Maysville, Dravo takes maximum advantage of opportunities for reloading carriers with limestone for outbound backhaul movement. Coal, shipped from southeastern Kentucky mines in rail cars, is transferred to barges at a river terminal in West Virginia. After it is unloaded at Maysville, the barges are cleaned with a front-end loader and then reloaded with limestone. Limestone also is backhauled in connection with truck deliveries of coal. The economics of using backhaul shipments has permitted Dravo to enter into markets in which Maysville limestone otherwise would not be competitive. The company plans to backhaul limestone in empty open hopper cars in the future. As part of its ongoing assessment of the distribution system that supports the Maysville operation, Dravo Lime recognizes that a new environment has developed between shippers and carriers because of regulatory changes in the railroad and trucking industries. Although dry bulk shipments by barge to and from Maysville have always been unregulated, other forms of transportation have not. With railroads and motor carriers now approaching varying degrees of deregulation, contracts and agreements are replacing tariffs, and rate negotiations are becoming a daily activity. Dravo Lime plans to take advantage of these transportation changes, all of which may be beneficial to both its plant and its customers.

Jan 10, 1982

By J. E. Moyle

Introduction In October 1983, Rio Algom Ltd. decided to develop the East Kemptville tin deposit. This decision was the result of intensive geological and metallurgical evaluation work, as well as careful studies of environmental and marketing aspects. The property is located about 54 km (34 miles) northeast of Yarmouth, Nova Scotia, near the village of East Kemptville. Geology The geological setting is a granitic intrusive at the contact with metasediment. The tin mineralization is in the form of cassiterite (SnO2), which is about 80% tin. Sulfides are associated with the deposit containing silver, copper, and zinc, which are recoverable as byproducts. The mineralization is associated with quartz veins and greisen alteration. In the center of the deposit, the zones are so close together they have the appearance of a massive or porphyry type deposit. Ore Reserves The mine plan is based on 56 Mt (62 million st) at 0.165% tin. Up to the ninth year, mill feed will average about 0.2% and lower grade material will be stockpiled. In later years, the average grade will be 0.16% tin. A 0.08% cutoff grade is planned for the entire 17 years of production. East Kemptville is a relatively low grade tin deposit, and only a combination of favorable circumstances has made it economic. • The ore body is situated at, or very close to the surface, permitting mining by open-pit methods at a very low stripping ratio. • The tin occurs in relatively large crystals that allow for good recovery by gravity techniques. • It is ideally located in a well-settled area, with all essential infrastructural requirements already in place. • The positive and cooperative response from various governmental agencies involved are encouraging. Mine Plan The mine plan incorporates an initial pit, followed by three expansions to the ultimate pit. Mining will be at 14 kt/d (15,000 stpd) and will include 9 kt (10,000 st) of ore plus 5 kt (5,500 st) of waste and low grade. After five years, the mining rate will increase to 21 kt/d (27,500 stpd). It is planned to drill vertical 165-mm (6.5-in.) blast holes on a 6-x 6-m (20- x 20-ft) pattern. Bulk slurry explosives will be used to break the rock. Loading will be with hydraulic shovels into 70 t (77 st) haulage trucks. The trucks will deliver the ore to a 13 x 20 m (42 x 65 ft) gyratory crusher, where it will be crushed to 150 mm (6 in.). Secondary and tertiary cone crushers will be used to further crush the ore to 13 mm (0.5 in.). Process Design Tin extraction technology is practically unknown in North America, but Rio Tinto Zinc, which has a 53% ownership in Rio Algom, is involved in tin production in the UK. Rio Algom has used this experience and expertise in metallurgical evaluation work and in tin-related aspects of plant design. Mineralogical and metallurgical test work have been performed, both on laboratory and pilot plant scales. Mineralogical work was done largely in the UK, the laboratory test program was carried out at the Lakefield research facility in Ontario, and pilot plant work was conducted in Australia. This program has resulted in significant improvements in recovery and concentrate grades, over best projections that could be made before this work was carried out. Concentrating Process The concentrator is being designed to process about 9 kt/d (10,000 stpd). The first step is to reduce the size of the ore to -700 µm (-24 mesh) in a rod mill/ball mill grinding circuit. The ball mill will operate in closed circuit with high capacity banana-type screens. The screened product will be deslimed to 30 µm (560 mesh) with cyclones, then passed over the pri-

Jan 4, 1984

By Ashma Singh, Nichole Maistry

Due to declining iron ore grades, low-grade ores with complex mineralogy — namely, banded iron formation (BIF) — are being explored to maximize iron ore resources and increase the life of mine. Flotation is the standard global process used for the beneficiation of BIF ores, as it is a complex ore reserve, and liberation is typically achieved below 1 mm. This study focuses on the flotation of a South African BIF, evaluating its response to different collectors, as well as effect of grind. As flotation is an expensive process and South Africa ranks high on the production cost curve, preconcentration by gravity or magnetic separation is performed prior to flotation. Thus, flotation was also performed on a gravity concentrate to determine if a grade suitable for steelmaking (approximately 63 percent) is achievable. The results indicate that the use of an alkyl ether amine-based collector partially neutralized with acetic acid is suitable for separation of hematite from illite and quartz at high pH values. Further optimization tests are being pursued to improve overall recovery and grade.

May 1, 2025

By Thomas J. Feeley

The US Department of Energy (DOE) is supporting the engineering development of three advanced physical coal cleaning technologies: selective agglomeration, advanced flotation and advanced cycloning. Each is capable of significantly reducing the pyritic-sulfur content of US coals. The objective is to provide the coal and electric-utility industries with a cost-effective option for addressing the SO, emission reductions required by the 1990 Clean Air Act Amendments (CAA). A secondary objective is to evaluate the potential of advanced coal cleaning for removing trace elements that are precursors to the formation of hazardous air pollutants (HAS). The proposed National Energy Strategy (NEE) and the 1990 CAA lay a foundation for a more efficient and environmentally sustainable energy future (1991). The need to use energy resources in an environmentally sound manner presents critical challenges and opportunities for coal preparation during the next decade, particularly regarding the control of SOS and HAY emissions. The principal challenge is the development of cost-effective coal preparation approaches for sulfur and HAY precursor removal.

Jan 1, 1993

By Roger Nendick

The recent developments in refractory precious metal ore processing (Bio-oxidation, Autoclaving), and the revitalization of the more traditional roasting processes have attracted great attention in recent years and are indeed the focus of todays symposium. It must always be remembered, however, that the term refractory ore by definition means that the material 'must be capable of being treated at a profit". Given the high cost of the refractory processes, the requirement to be treated at a profit requires very close scrutiny during the evaluation phase of the property development. The M.G.M. film company has the latin motto Ars Gratia Artis meaning Art for Arts Sake. Ingeniatore Gratia Ingeniatoris (a very crude attempt at saying Engineering for Engineerings Sake) should not be the motto for mining companies intent on exploiting refractory gold deposits, but rather the wittily tilted heading for this paper "Take the money and run like a thief". The following hypothetical case studies show that the high technology solution is not always the best financial solution.

Jan 1, 1990

By Gary J. Goldberg

Through the early 1980s, surveying at Bingham Canyon required a great deal of repetitive and manual work. The advent of total station surveying equipment provided an opportunity to improve the speed and accuracy of surveying work while reducing manpower needs. An evaluation was made of total station systems and their ability to meet the surveying requirements of Bingham Canyon. This culminated in the purchase of a total station system as the mine reopened in 1986. The surveying department at Bingham Canyon during the early 1980s consisted of three, four-man crews using theodolites and self-leveling levels to perform the majority of the field work. Office work involved data reduction and hand plotting. Although hand-held programmable calculators were used, a great deal of time was spent manually transferring field notes to final calculations. After shutting down in early 1985, plans for start-up of mining operations in 1986 included a review of all aspects of the operation for cost and productivity improvement. Applying total station survey capabilities offered the potential to improve surveying accuracy and speed while reducing manpower needs.

Jan 1, 1990

In order to analyze and quantify distinct environmental properties in the vicinity of sites, the Site-Specific Natural Resources Information System (SARIS) has been developed based on a Geographic Information System (GIS). SARIS is one of the fundamental databases of a collaborative research program aiming at the resource orientated analysis of metallic raw material flows with aluminum and copper serving as exemplary case studies. The spatial database incorporates all present production sites of ore extraction, refining and smelting. Environmental data for each location were derived from global digital survey data covering land cover, soils, morphology, climate, topography and population density. The main application of this database is the characterization of environmental safeguard objects, which may be affected by the activity of concern. This site-specific environmental impact assessment is used to determine the relevance of environmental issues based on the distribution pattern of sites in a global framework. The derived results are used to suggest a tailored indicator approach to measure progress and performance of industrial developments relative to the predetermined site-specific conditions.

Jan 1, 2003

By G. I. Karydakis

Geothermal energy is an important energy asset which can play a significant role in providing energy resources to cover energy needs of a country while it can play a primary role in a particular region where it is abundant. Greece is especially rich in geothermal energy. The collision of Euroasiatic and African plates coupled with the strong tectonic tension, particularly in north Greece, resulted in the formation of important geothermal fields of low, medium and high enthalpy. These fields are in the Aegean islands, in central and east Macedonia, in Thrace and in central Greece. This work presents and analyzes information about the drilling activity for exploration and production of geothermal fields of low, medium and high enthalpy in Greece for the past thirty years. The number and type of wells drilled together with the spatial and the yearly distribution are given. Depth data has been analyzed according to the fluid temperatures and to the geological formations. Cost data are presented and analyzed for the total number of wells drilled giving also the cost per meter drilled.

Jan 1, 2006

By Anthony J. Peach

With the new generation of so called "Super TBM", we would all expect to witness the implied super-performance. In some instances this is occurring, but one must ask why is it not occurring in the majority of applications? For hard rock TBM related projects, we are observing a decrease in the volume of projects in the previously traditional areas such as North America and Western Europe and an increase in Asia (Hong Kong, Indonesia, China, Korea etc). As a consequence less experienced contractors are acquiring the latest ultra high power equipment, without the knowledge necessary to achieve optimum performance. The interdependence of TBM and muck removal systems has been assessed with emphasis on the emergence of the continuously extending conveyor technology, as a means of achieving dramatic productivity increases. The Australian system assessed here at the time of drafting this paper holds the world record tunnel excavation production of 2,166 metres. A little considered aspect of the adoption of conveyors is the associated improvement in safety.

Jan 1, 1995

By Donald P. Richards, William M. Greenslade, Daniel E. Albers

INTRODUCTION The application of oil field technology to large diameter hole drilling is beginning to offer a cost effective alternative to conventional shaft sinking methods. The drilling of ventilation and small production shafts are, of course, not new. The major constraint to the drilling of large diameter production shafts has been the inability to drill holes large enough and straight enough to install and operate relatively high volume hoisting equipment. This paper discusses recent advancements in drilling technology as applied specifically to large diameter holes for use in the mining industry. The paper emphasizes the geotechnical and hydrologic considerations in assessing site conditions and their application to drilled shaft technology. The authors worked together on a recent feasibility study for a 6 m (20 ft.) diameter 975 m (3,200 ft.) drilled shaft in New Mexico. Their individual experience in drilling and geotechnical investigations related to shaft sinking is world wide. DRILLING TECHNOLOGY Large diameter hole drilling has been a natural evolvement of oil well rotary drilling techniques. Most problems that were encountered in the rotary drilling of large diameter holes have been

Jan 1, 1981

By Leonhard Schmid

INTRODUCTION In the region of Zurich several of the Swiss Interstate Highways meet and have to be linked to form a continuous network. The subalpine glacial topography with hills, ridges and lakes requires the construction of many tunnels (Figure 1). The Milchbuck Tunnel forms part of the inner arterial highway system of the city of Zurich. It passes underneath the ridge separating the Limmat and Glatt valleys. In its final configuration the tunnel will consist of two parallel three-lane tunnels (Figure 2). For the time being only one tunnel is constructed. This tunnel will be operated with two outbound (climbing) lanes and a single inbound (descending) lane (Figure 3). The owner, the Canton of Zurich, awarded the contract for the construction to a joint venture with the following three contractors: Locher & Cie AG (leader), Prader AG, A. Brunner's Erben, all located in Zurich. The actual freezing was performed by subcontractor Philipp Holzmann AG, Mannheim, West Germany. Electrowatt Engineering Services Ltd, Zurich, was design engineer and performed the construction supervision.

Jan 1, 1981

By Carlo Grandori

Foreword In loose ground and soft rock formations, mechanical tunnel boring is necessarily dependent on the adoption of shield machines and the application of adequate support or lining structures. These structures are erected either within or immediately behind the rear portion of the shield and provide the required reaction to the forward thrust. In competent rock formations where systematic support is not a requirement, hard rock tunnel boring machines generally advance by thrusting from a structure gripped against the tunnel walls. These machines may feature a more or less extended cutterhead shield or roof support, but when in weathered, fractured or otherwise weakened ground, or in fault zones filled with soft gouge, the gripper mechanism often cannot provide enough thrust reaction to advance the cutterhead. Under these conditions, early support of the arch and walls is generally required in the form of rock bolts, steel rings and laggings and some times of a primary concrete lining placed in the short section between cutterhead and grippers. Such tunnel support measures generally fail to produce an adequate increase in thrust reaction capacity, but

Jan 1, 1976

By Joseph A. Dos Santos

Developed in 1983, high angle conveyors - HAC®s are proven versatile systems for elevating materials continuously from a lower to an upper level. Such systems may also be used to lower materials continuously. HAC®s have found commer­cial application in widely varying materials (including coal, refuse, coarse ores [-250 mm], hot clinker, municipal sludge, wood chips, gypsum, slag, excavated earth, various grains and RDF), at widely varying throughput rates from 0.27 to 4250 t/h. The conveying profiles have varied widely and elevating heights range from 3.66 m to 175 m. HAC®s have found application in coal, copper and iron mining, and preparation, in municipal waste treatment, rapid transit projects, pulp and paper mills, cement plants and in gold mining. While noting a wide variety of applications in general, the present writing focuses on Newmont Gold's HAC®, near Carlin, Nevada, which elevates very coarse gold ore to the screening plant. Additionally, upcoming HAC® applications in gold mining are discussed and a proposed multi-flight vertical HAC® system from a deep underground mine is described.

Jan 1, 1996

By Jim McMaster, Charles W. Kenney

The role of oxygen in cyanide leaching ia well understood in the gold industry. Oxygen enrichment has taken on a real, practical meaning to operators with the were to evaluate the effect of oxygen enrichment on the kinetics of heap leaching gold ores, to examine methods of oxygen application in the heap, and to develop preliminary economics for the process. Several series of column tests were completed increasing preaeration, applications. use of pure oxygen for leaching, and in CIL in the test program. Oxygen enrichment may have a significant place in heap leaching as well. In preliminary column tests sponsored by Kamyr at Hazen Research, Inc. , oxygen-purged columns showed an increase in both the leaching rate and maximum recovery of gold and a reduction in cyanide consumption compared to columns run with air. Potential benefits of using oxygen in heap leaching include faster leaching kinetics, shorter cycle time, higher recoveries, and more efficient use of permanent or reusable pad space. The concept requires confirmation of technical and economic feasibility on a commercial scale.

Jan 1, 1990

By Andrzej M. Wala

The determination of the air quality needs to dilute diesel exhaust gases to a safe level must be individually evaluated for particular cases. One such case is when diesel-powered vehicles are working in long dead- end headings with forcing auxiliary ventilation. The vehicles perform specific operations in a cyclic order required by the technical process. The dynamics of this process in certain conditions has a vital influence on environmental conditions in the working area and in the rest of the heading. Recent studies on diesel gas behavior in long headings have shown a zone of increased concentration of pollutants (accumulation) between the face and the mouth of the heading. To be able to control these accumulations of pollutants, use of the concept of planned air discharge by using the Coanda-type ducts is proposed. The main objective of this paper is to demonstrate an application of computer simulation of that process. It is shown that, by planning the additional air discharge, the concentration of diesel gases can meet required limits along the heading.

Jan 1, 1987

By Patrick G. Hill

This paper discusses safety protocols for Kiewit Construction’s Level (3) project. The Level (3) project will cover a majority of the United States, and literally thousands of site operations will be conducted over a wide geographic area under challenging conditions; rivers, roads and other features, both from the surface and often for great and from boring pits. Developing a progressive safety plan for fast-track linear projects using micro-trenching and directional boring techniques requires significant investigation, planning and evaluation. Safety protocols for inner duct installation, to be accomplished with extensive use of directional boring is an essential part of the safety plan for network construction. In light of the shear volume of work and the geographical extent of this project, in many different types of terrain, this paper will identify approaches to safety applicable to fast-track linear projects, whether surface or underground-based. Establishing a safety culture into all aspects of this operation will improve productivity and cut unnecessary expenses. This new approach involves continual improvement and evaluation of hazard analyses, inspection procedures and training.

Jan 1, 1999

By Michael J. Virnig, Murdoch W. MacKenzie, Michael R. Davis

The objective of this paper is to present preliminary capital and operating cost estimates (±25%) comparing conventional carbon-in-solution (CIS) with resin-in­solution (RIS) using AuRIX® 100 for the recovery of gold and silver from typical heap leach solutions. Preliminary testwork was carried out with AuRIX® 100 using real and synthetic leach solutions to determine the technical viability of the resin for gold/silver recovery and to provide process design parameters for the preliminary RIS circuit. The scope of the resin testwork was sufficient to support the level of accuracy applied in the capital and operating cost estimates. No parallel testwork was carried out with activated carbon. Industry standard design data and operating data from existing CIS operations were used as a basis for the comparison. Both the capital and operating cost comparisons indicate a substantial savings for a RIS circuit using AuRIX® 100 (- 14 to 18% in terms of capital and 25 to 35% in terms of operating costs) over a conventional CIS circuit depending upon solution flows and grade.

Jan 1, 1999