Search Documents

By A. Mukherjee

This paper presents an analytical technique for prediction of the damaged rock zone (DRZ) around a circular drift subjected to an anisotropic stress field (analytical solution exists only for the case of hydrostatic stress field). The method can readily be adapted to micro or personal computers. Stress concentrations around the drift are calculated at the centers of small rock elements, using the analytical solutions for a hole in an infinite plate. Potential failure of a rock element is assumed to be governed by the Coulomb failure criterion. When the failure condition is exceeded for an element, the excess shear stress is transferred to the neighboring elements. Progressive failure is allowed to occur until convergence is obtained. The final configuration of the damaged rock zone so obtained can be used to assess rock support requirements, as well as modified modulus and permeability of the DRZ.

Jan 1, 1988

By Fred N. Kissell, Robert J. Timko

Safe escape from coal mine fires continues to be a concern of the mining industry. The most life-threatening fires occur outby the working sections. Because stoppings always leak some air, an outby fire may in time cause intake escapeways to become contaminated with smoke and toxic gases. Smoke and gas infiltration into intake escapeways can be minimized by raising their air pressure over that of adjacent airways. This can be done by checking off the intake escapeway near the working face. The Bureau of Mines has investigated the use of a parachute stopping as a quick-erect check curtain during mine fires, and the concept has been tested in several mines. In every instance, when a parachute stopping was erected on the section, the intake pressure went up substantially. The pressure-raising effect of the parachute persisted for up to 1200 m (4000 ft) outby. Results indicate that checking off the intake escapeway may serve as a viable way to improve safety during mine fires.

Jan 1, 1991

By H. Bernatowicz

The Nucoalyzer (On-Line Nuclear Analyzer) is a new method recently made comercially available for monitoring the elemental composition of a process stream. Applications for the Nucoalyzer include grading ore on a conveyor belt before or after it has gone through primary crushing, monitoring the slurry being transported in a pipe to the concentrator, and monitoring the stream of concentrate or the tailings from the concentrator. The Nucoalyzer may also be used at the smelter to monitor elements in the feed that include copper, sulfur, iron and silicon where a uniform feed is desired. The advantage of the Nucoalyzer over most other techniques are (a) it performs the measurement directly on the process with no sampling necessary, (b) the analysis can be performed on streams of particulate and slurries, and (c) the system does not have to make contact with the material it measures. These Nucoalyzers are operating at coal fired power plants and several more are about to be placed in service. This paper discusses the principles of operation of the Nucoalyzer, our experience in the field, application of minicomputers to data reduction, and potential applications in the ferrous and non-ferrous industries.

Jan 1, 1982

By W. Kuckshinrichs

Metallic raw material flows are characterized by a complex global network of producers and consumers, as well as by a multitude of ecological, economic and social impacts across national boundaries and on different scales. This leads to the need to develop methodologies, which allow identifying obstacles that prevent metallic raw material flows to contribute to sustainable development. From a scientific point of view CRC 525 (Martens 2003) has developed an holistic indicator set consisting of approximately 80 different indicators. This set is taking into account the multi-dimensional character of sustainable development. Moreover the indicators reflect different system boundaries according to different actor levels and decision contexts. The full indicator set is important in scientific considerations and suitable for scientific awareness creation. However, to fulfil the function of a decision support approach for political and economic decision-makers some modifications are of central concern. At first a reduction of the full indicator set by selection of core indicators enables decision-makers to deal with complex issues of contrary economic and societal protection targets. Secondly, as thresholds of indicators justify societal call for action, they are discussed against its political or scientific origin. The proposed methodology is exemplified by indicator-based studies of the material flow of aluminium.

Jan 1, 2003

By S. Yang

Based on an analysis of the features found in Chinese surface coal-mining areas, including areas that have already been developed and areas that are in the process of being developed, this paper discusses some rational coal-haulage systems. An optimal decision-making model, which includes a geological model, a mining model and an economic estima¬tion model, was developed for the selection of a coal-haulage system. A case study is presented.

Jan 1, 2000

By Friedrich Steinhäusler

RADON SOURCES AND CONTROL MEASURES IN THE MINING ENVIRONMENT Most of the contamination of the mine atmosphere by radon 222 is due to radon emanating from solid or fractured ore surfaces of walls, roof and floor. Also radon gas emanates from broken ore either from storage in backfilled mined-out areas as applied in e.g. shrinkage stopping methods or from ore spillage along intake airways mainly due to the use of trackless haulage. To a lesser extent water itself can represent an additional source of radon, which emanates into air from open drainage ditches or seepages along intake airways. The contribution from water can be controlled effectively by isolating the water from the primary intake air system, e.g. by diverting the water through pipes and/or sealing of seepages by grouting. However, control of radon emanating from rock surfaces creates a major technical problem with significant impact on the economic aspects of mining operations, if adequate radiological conditions must be maintained. Basically this can be achieved by suppressing the emanation process itself, confining already emanated radon or by removal of radon from the mine atmosphere. Extensive research has been carried out on the rate of radon emanation as a function of barometric pressure changes (Pohl-Rüling and Pohl, 1969). It could be shown that the radon supply consists of a permanent and variable component. The former results from the surface of the rock and depends mainly on the emanating fraction of its radium 226 content; the latter originates from within the rocks and is a function of the suction effect of decreasing barometric pressure, rock porosity and fissures. The practical application of this barometric pump effect for depressing the rate of radon emanation, e.g. by pressurizing the mine atmosphere, is limited due to high costs for providing a sink for absorption of radon and air as well as lack of permeability in most uranium ore bodies (Schroeder et al., 1966). Mine air cleaning by removal of radon can be achieved with the use of cryogenic methods, chemical removal, adsorption into charcoal beds, use of a gas centrifuge or general ventilation techniques. Technical problems have so far prevented the application of any of these methods other than ventilation. It is common practice to use the age-of-air concept, i.e. fresh air is delivered to the worker as directly as possible and removed quickly afterwards thereby maintaining the air "young". Engineering principles for quantity distribution of air through underground working areas are straightforward for general mining situations where radon constitutes an environmental contamination problem. However, in cases of high uranium ore content this concept may result in high costs with regard to installation and energy requirements for effecting both frequent air changes as well as sufficient heating of the air in cold seasons. Taking into account that the investment in ventilation systems is a major cofactor for the overall ore production costs this can be a limiting and decisive component in the assessment of the economic feasibility of specific mining operations and mineral reserves in general. Effective control of the radon flux from the rock surface prevents the initial contamination of the mine air with radon directly at the source. A radon diffusion barrier for practical application in mining requirements should fulfill the following requirements: - reduction of radon emanation rate by at least an order of magnitude - high mechanical strength - ease of sealant application onto surface to be coated - water resistant - low fire hazard - resistant to temperature changes encountered in mines - high cost efficiency in relation to exposure reduction achieved (direct and indirect costs) - low degree of maintenance. In the past several materials have been tested as sealants for controlling the emanation of radon from surfaces of rock and building materials. Epoxy paints reduce radon emanation rate only by a factor of 2 to 6 (Auxier et al., 1974; Eichholz et al., 1980; Keith Consulting Engineers, 1980). Although it is possible to prevent the escape of more than 99 % of the radon to the environment with gel seals over 80 mm thick (Bedrosian et al., 1974), practical applicability is very limited. Multilayer coatings of epoxy resins with various additives require meticulous preparation and flawless application of seamless four-layer coatings in four days to impede radon diffusion (Culot et al., 1976), otherwise results from this method have not been totally satisfactory (Leung, 1978). Aluminium foil laminated with polyethylene and paper on each side is under test as radon barrier but results are not available yet (Ericson, 1980). However, this method has the inherent disadvantage that possible malfunctioning electrical installations can cause fire or electrical shock through the sealant. Polyurethane foam coatings have been used on stoppings as very effective sealants. It does, however, represent a potential danger of spontaneous ignition and it is expensive (Rock, 1975). Thus, there is still need for a material which has similar properties as outlined above. In the following results are reported from investigations on the suitability of various materials as radon diffusion barriers.

Jan 1, 1981

By Tim Neil, O&apos

Introduction Compania de Carbones de Chile (Cocar SA) has brought into production Chile's first large-scale, open-pit coal mine, located in the Magellan Province. The US $65 million project includes a 1.1-Mt/a (1.2-million stpy) subbituminous steam coal mine and a mechanized bulk loading marine terminal with water depth sufficient to receive 60 kt (66,000 st) Panamax vessels. The loading terminal will be one of the largest in Chile. The Pecket coal project is expected to save Chile about $40 million in energy production costs and a further $100 million in oil imports, or about 25% of the country's oil import costs. Pecket coal will generate electricity for Codelco and will also supply general electricity needs for northern Chile. The Pecket coalfield is located on the Brunswick Peninsula, about 30 km (19 miles) northeast of Punta Arenas, the provincial capital, as shown in Fig. 1. Pecket is part of a large, coal-bearing basin. It extends from Punta Arenas 250 km (155 miles) north to Puerto Natales and across the border into the Rio Turbio coalfield in Argentina. A fleet of large and small O&K hydraulic shovels and backhoes is used to dig and load overburden and coal into mining trucks while O&K graders maintain the haul roads in and around the pit. Coal occurrence in the Magellan area of Chile has long been

Jan 1, 1988

By Bernardo Portillo, Alejandro Perez, Daniel Norrgran, Joseph Wernham

High gradient permanent magnetic separators (termed "Ferrous Wheel") are described as used to recover the iron bearing minerals from mill tailings at the Grupo Acerero del Norte's Hercules iron mines in Coahuila, Mexico. The pilot scale test work as well as the "in-plant" test work provided the basis for a 385 MTPH plant expansion to be commissioned late in 1995. Approximately 6 million metric tons of flotation tailings averaging 50 percent iron, mostly as hematite, are contained in two separate ponds. The tailings are relatively fine at 93 percent -200 mesh and 72 percent -500 mesh. After testing various recovery methods, a high gradient permanent magnetic separator was selected to produce a preconcentrate prior to flotation. The separator uses a flux converging matrix to generate high gradient magnetic fields and capture the hematite. The advantage of the Ferrous Wheel high gradient permanent magnetic separator is the use of permanent magnets as opposed to electro-magnets. Further the vertical rotating ring is much more conducive to matrix cleaning as opposed to the conventional horizontal ring separators. This feature also allows the use of a wide range of matrix materials to achieve the optimum metallurgical response

Jan 1, 1995

By C. Allen, H. Zhang, L. Falk

Shock loss occurs when there is a change in the area of a drift or airflow direction. These shock losses accumulate throughout the ventilation system and will increase the mine resistance as underground development deepens or becomes more complex. Hence, shock losses should be carefully considered when establishing the resistance through a series of branches as they can be a significant contributor to the estimated mine resistance. Using computer software to simulate a ventilation system is common but applying reasonable shock loss factors in the software is not a simple or direct process. Determining shock loss values includes the consideration of historical measurements, application of factors and formulas from literature based on the geometry and complexity of junctions, and the geometry variation at different locations. For example, the shock loss at the bottom of a ventilation raise can consist of a 90° bend and a sudden area change. This paper presents an approach for estimating shock loss factors near raise junctions using computational fluid dynamics (CFD). Current and future work will also be compared with field measurements. Results from this approach are compared with software defaults as well as classical techniques in published literature and standards.

Sep 1, 2024

By G. Ferrara, P. Bozzato, B. Chinè

To obtain a reliable comparison between conical and cylindrical separatory vessels used in dynamic dense-medium separation systems, the following two studies were made: a study of the swirling flow in conical and cylindrical vessels using laser-Doppler velocimetry (LDV) and a study of the behavior of suspensions of magnetite and ferrosilicon in water in both separators. It was found that the tangential velocity profiles differ in conical and cylindrical vessels. In a conical cyclone, free vortex conditions affect the largest part of the vessel, while in a cylindrical vessel, the motion approaches that of a forced vortex, i.e., that of a centrifuge. It was also found that the conical vessel manifests higher centrifigal acceleration and very strong densifying (the density differential) and, hence, the density gradient inside the vessel is large. It was found that the cylindrical vessel manifests lower centrifugal acceleration and low densifying, i.e., low-density differentials, and hence, the density gradient inside the vessel is small. Also, due to greater densifying, the density cut-point in cyclones is higher than the operating medium density, while, in cylindrical vessels, the density cut- point is closer to the medium density. The results provide an interesting description of the differing behaviors of conical and cylindrical vessels, and they help explain the differences in pegormance between the two types of separators.

Jan 1, 2000

By S. Mathur

Future Florida phosphate reserves contain higher MgO than presently mined deposits. The high MgO content is contributed by dolomite and Mg-rich clay, palygorskite. Selective flocculation was attempted to reduce the MgO content of apatite in synthetic mixtures of apatite with dolomite and palygorskie. Mixed mineral selectivity was predicted in the apatite-dolomite and apatite- palygorskite systems with Poly(ethy1ene oxide) (PEO) flocculant. Loss of selectivity in the mixed mineral systems was primarily attributed to heteroflocculation, which was minimized by addition of a Site Blocking Agent (SBA), a lower molecular weight fraction of PEO, prior to addition of the flocculant. A 80:20 mixture of apatite-dolomite (or palygorskite) was upgraded as 95% apatite at more than 80% recovery level in the product fraction.

Jan 1, 1995

By Deepak Malhotra

Comminution circuits in general account for fifty percent of capital and operating costs for a processing plant. Significant advances have been made in optimization of these circuits. One would expect a few circuits to be the favored designs for plants. Review of grinding circuits worldwide indicates that a variety of circuit designs are utilized for non-technical reasons. A brief review of circuits and reasons for their selection is given in this paper.

Jan 1, 1998

By C. J. Johnson, C. J. Bise

Coal extraction by continuous miners (CM) is currently the most common underground method in the US industry and accounts for slightly more than two-thirds of the nation's deep mining production (National Coal Association, 1987). Even if longwall mining should become more commonplace, it can proceed only after ventilation and access entries have been driven by CMs. Since an area of concern continues to be the effects of the dust generated on the health of mineworkers, this paper discusses the relationship between the elemental compositon of mining-generated airborne dust sampled from the immediate ventilation return of a CM and laboratory-generated dust derived from channel samples taken from the mines. There are several potential contributions of this type of study to the coal mining industry. First, after more fundamental knowledge of the causes of Coal Worker's Pneumoconiosis (CWP) is learned, the laboratory-generated respirable dust could be used to identify a potentially hazardous coal seam. Also, this study could possibly aid in understanding the fundamental causes of CWP by producing mining-simulated samples of coal dust that could be used in epidemiological studies. Further. assuming that there is no difference in the elemental composition of a drill-core sample and a channel sample from the same location, a mining company could predict anew mine's respirable dust elemental composition in the immediate ventilation return by using exploratory drill core samples of the roof, coal, and floor rock to prepare the laboratory dust. Ventilation engineers could then use engineering design and control measures during premine planning to reduce the incidence and severity of CWP by better ventilating the potentially hazardous coal seam. If this proper planning prevented any future changes to the ventilation equipment and mine design. much time and money could be saved. Scope of work To investigate the variability of the chemical characteris tics of respirable dust, airborne dust samples from eight underground coal mines located in the eastern and midwestern United States were collected with eight-stage Sierra Model 298 Marple cascade impactors, as well as 25 channel samples of mined material. Each channel sample was removed from the middle of the coal face before mining occurred. Sampling of the mining-generated dust was conducted by Lee (1986) by sampling the entire working sections, primarily for characterization purposes, to obtain information on the locational variability of dust characteristics. Research performed for this study used the elemental analyses of the mining-generated dusts he sampled in the immediate ventilation returns of CMs. The procedure that was used to produce the laboratory generated respirable dust was based on the Hardgrove grindability test since it reflects the pulverizing characteristics of coal. This test was chosen for several additional reasons. First, it is repeatable and reproducible. A consistent amount of input energy is used as well as a specified size range of feed material to be crushed (the channel samples). Second, it is thought to generate secondary dust in a way similar to that of the crushing and grinding of the coal and rock as they pass through the arc-shaped cutting path of the CM's cutter head. The potential effect on dust generation by this secondary grinding mechanism may be at least as much as that produced by primary fragmentation, which is dust produced by the cutting action of the bit against the coal or rock (Roepke. 1984). Finally, the Hardgrove grindability test is well known and is used in the coal industry to guide mineral processing engineers in estimating the capacity of mills used to grind coal. One hypothesis of dust researchers in the Generic Technology Center for Respirable Dust is that the elemental as well as the physical characteristics of coal mine dust will make a difference in the incidence and severity of CWP. Coal mine dust is generated not only from coal, but also from any rock partings contained within the seam or any roof or floor material mined with the coal. Thus, coal mine dust may not have the same elemental characteristics as the coal being mined. Given that hypothesis, mixtures proportional to each thick¬ness mined of roof, coal, and floor rock derived from the channel samples of the face areas from which the respirable dusts were generated by the CMs were used to produce the feed material that was pulverized in the Hardgrove machine.

Jan 1, 1990

By Peter J. Szabo

Introduction There has been much said recently about the sophistication of Japanese management in turning out reliable, inexpensive products, such as cars and steel. Techniques include consensus management and quality control circles. These have been touted as prime reasons for inexpensive Japanese products. An often neglected, but major factor in the equation of cheap export goods is the role played by Japanese trading companies. These venerable institutions are a vital factor in Japan's overall strategy of keeping the price of raw materials at the absolute lowest levels. This is critical to the country's economy since the nation must import more than 85% of all its coal. A country that is so desperate for imported raw materials would appear, at first glance, to be at the mercy of its suppliers. In Japan's case, however, the opposite is true. With the exception of brief' windows in 1974-75 and 1980-81, Japan has been in the driver's seat in negotiating contract terms. Due to its dominant role in world coal trade, Japan's situation can be described as a de facto monopsony. By definition, a monopsony is a market situation where the product, in this case coal, is offered by many sellers, but is sought by one buyer. This has been due to the role of Japanese trading companies in dealing with suppliers. Table I depicts trading companies by size in 1982. Mitsubishi and Mitsui are overshadowing in terms of size. The others, though less significant, play a vital role in orchestrating the marketplace. Three critical building blocks on which the strategy of the trading companies are based include intelligence networks, exceptional training of company traders, and shrewd contract negotiation practices. Intelligence Networks All success is derived from these three key components. Of the three blocks, intelligence gathering is the most important. With all the sophistication of the Central Intelligence Agency, the Federal Bureau of Investigation, Interpol, and the Surete', the Japanese trading company's method is every bit as competent and far more gentlemanly. Friendly competition is the key to survival. Although one Japanese trading company appears to be in ardent competition with its rival Japanese trading companies, when studied closely, a totally different picture emerges. The end user nominates certain trading companies as market channels and informally guarantees they will receive compensation regardless of which company wins a specific order. With this concept in mind, the pressure is off. The trading company can aim at getting the best price for the end user. Therefore, bargain, beat, and share information. Do whatever is necessary, but get the lowest price for the end user. Even with the game so gentlemanly, no victory could be assured without an adequate intelligence network. Proper intelligence is only as good as the sources drawn from. But how is one assured of getting the right information? The answer is verification. Verification is comprised of numerous independent sources each cross checked at a central processing unit in Tokyo. Each major Japanese trading company receives input, not only from its own trader, but from other trading companies as well. In addition to their own compilation, trading companies rely on the The Coal Manual, published annually in Tokyo by TEX. This manual covers every major coal producing country. Mines are located and seams identified, mining recovery, equipment lists, washing yield, railway distances

Jan 1, 1985

By D. A. Stanley

The Bureau of Mines has developed an equation which describes the dewatering of clay slurries with polyethylene oxide. This dewatering equation is An _ kC + b where n, k. and b are empirical constants and C is the concentration of polymer solution used for dewatering. The minimum amount of polymer required for dewatering. A is determined by titration of the clay slurry with a polymer solution. In this report, the dewatering equation is applied to data obtained for a polyacrylamide dewatering sequence. Fundamental similarities between the dewatering properties of clays and the viscosity of polymer solutions were observed. These similarities were explained by correlating an equation describing polymer configuration in solution with the dewatering equation. This correlation showed that amount of polymer required for dewatering and polymer solution viscosity are both consequences of the frictional interaction of entangled polymer coils.

Jan 1, 1989

By James K. Grunig, Rodney J. Anderson

A process consisting of leach, continuous countercurrent decantation, resin-in-column ion exchange, evaporative crystallization of beryllium sulfate, and decomposition of the sulfate was developed for Spor Mountain, Utah, ores. The process is metallurgically sound, has a minimum of process steps, and is applicable to a wide variety of beryllium ores. The most novel aspect of the process is a resin system of ion exchange which is highly selective for beryllium and which rejects substantially all impurities except for minor amounts of aluminum, magnesium, fluorine, and sulfate in addition to beryllium. The oxide from sulfate decomposition meets specifications of potential users.

Jan 1, 1983

In general, it cannot be assumed that the strength of coal pillars remains constant over long periods of time. Field observations indicate that a coal seam, especially when it contains a parting layer, deteriorates over time, reducing the load-bearing capacity of the pillars. This paper discusses a unique approach to determining the time-dependent strength of coal pillars in the field. Three coal pillars that were developed 5, 15, and 50 years ago were chosen for the study. Holes were drilled in coal and parting layers in each pillar, and the strength profiles were determined for each hole using a borehole penetrometer. The strength data were treated statistically to establish time-dependent strength equations for different layers. The results can be used to help estimate the loss of pillar capacity over time.

Jan 1, 2012

By O. M. G. Newman

The Electrolytic Zinc Company of Australasia Ltd., generates a jarosite waste at its Risdon smelter. Since 1974 this waste has been disposed of at sea off south-east Tasmania. As part of a monitoring programme prescribed by the Australian Government, bottom sediments from the disposal zone are monitored regularly. QEM*SEM image analysis complements conventional chemical analysis, having the ability to partition the occurrence of an element between sediment particles of metallurgical and natural origin. The adaptation of QEM*SEM techniques to the evaluation of bottom sediments provides insight into the fate of the particles of jarosite waste.

Jan 1, 1989

By J. W. Jang

The wear behaviors of grinding media with different chemical compositions and microstructures in wet grinding of a quartz-pyrrhotite mixture was investigated under various environments. The marked ball wear tests showed that the wear rate could be minimized by a suitable combination of martensite and ferrite within the same ball. A ball composed solely of hard martensite exhibited increased wear under an oxygen environment, while balls composed of both soft ferrite together with hard martensite exhibited decreased wear due presumably to the difference in their passivation? behaviors. The galvanic interactions between the two phases as well as among these phases and an electroactive mineral were investigated through electrochemical measurements under abrasive conditions in a slurry. The rates of formation of passive films controlled the corrosion currents of the high chromium steel media. Corrosive wear and its effect on flotation are discussed using the passivation kinetics model thereby developed.

Jan 1, 1989

By R. J. Smith

Hornestake's Mclaughlin Mine is the first commercial application of pressure oxidation pretreatment of gold prior to cyanidation. Inherent to the autoclave process are several liquid/solid separations. Flocculant consumption represents a significant portion of the consumable reagent costs at McLaughlan. This paper focuses on the efforts of the Operating, Metallurgy and Engineering groups to improve thickener operation and minimize flocculant consumption. An operating philosophy incorporating feed solids control, increasing flocculant dilution water and minimizing flocculant solution shear has resulted in a reduction in 1986 flocculant costs of $0.054/t ($0.06 st) versus 1985 costs. Additional changes are projected to result in a further cost reduction of $0.20/t ($0.22/.st) in 1987.

Jan 1, 1988