Search Documents

By W. Hu

Traditionally, coarse wolframite ore processing has been done almost exclusively by gravity concentration methods. However, there has been a depletion of rich and coarse ore reserves and a proportional increase in the mining of low-grade, fine-grained complex ore feeds. This change has resulted in the need for better slime-processing technology. Research and development activities in this area have gained momentum, and recent innovations appear promising. This paper covers the recent innovations that have been made in dealing with tungsten ore slime processing. The new techniques include the application of a centrifugal cone separator, high-intensity wet magnetic separator, the use of phosphonic and arsonic acids as collectors in ultrafine wolframite flotation, and combined processes.

Jan 1, 1989

By Alexandru Corneliu Stematiu, Catalin Popescu, Radu Sarghiuta

"The tunnel sector is excavated into a rock mass heavily affected by tectonics, defined as a regional fault. The rock around the tunnel support undertakes the non – elastic deformation and gradually detaches from the rest of the non affected rock mass, moving inside of the excavated area and tending to fill up the whole space. The initial solution of using stiff support consisting in double steel ribs I12 with circular shape in the upper part and straight vertical pillars in the lower part has proved to be inadequate. Based on the calculations of the subsidence phenomena and a mathematical model, the proposed alternative support was provided by special circular steel ribs – SG-23 –that allows a limited rib deformation (by relative slip between the arch segments) in order to mobilize the contact between the rock contour and the inner face of the rib - not only for the deformed rib but also for the neighboring ribs. 1. INTRODUCTION Hydropower development of Jiu river in Romania, in the narrow gorge sector includes two diversion HPP and a small hydro plant that provides the minimum required flow downstream: CHE Dumitra , CHE Bumbesti and MHC Livezeni (Table 1. Hydropower parameters).The Livezeni intake reservoir is provided by a gated dam located 1250 m downstream of merging point between Jiul de Vest river and Jiul de Est river. The dam is equipped with three radial gates with flap gates with a span of 12 m each and the height of (6 + 3) m. The longitudinal profile of Dumitra head and the location of the gallery zone that is the subject of the paper are presented in Figure 2. Longitudinal Profile – Dumitra Head."

Jan 1, 2016

By M. Kawulak

The necessity to protect the environment can limit mining activities and make some areas less attractive for the prospecting and exploration of mineral deposits. In Poland, the main environmental factors that restrain Irumng are: 1. Regional A Protection of the landscape B. Protection of ground water from contamination and depletion 2. Local A Conservation of fertile soils B. Conservation of forest resources C. Preservation of natural, cultural, and historical monuments The regional factors listed above that can limit mining are presented on a map of Poland. These data, combined with maps of known and potential mineral deposits, make it possible to delineate general levels of limitation for various mining-related activities varying from "no existing environmental limitations" to "no allowed industrial activity" As an example, a compilation of such data is presented for lignite exploration and mining in Poland. Lignite deposits occur within Upper Paleocene to Upper Miocene clastic strata at depths ranging from a few to 300 m. The thickness of the lignite is generally a few meters, but can locally reach over 100 m within grabens. As a result, the overburden-to-lignite thickness ratio varies from less than 1 to over 20. Within the same Tertiary strata, and within overlying Quaternary strata, several aquifers exist that produce good quality water that may be contaminated or depleted during lignite mining. The protection of these ground waters is the main factor limiting lignite mining and should be addressed in mining and environmental policy and planning.

Jan 1, 1996

By Daniele Martinelli, Rodrigo Winderholler, Daniele Peila

"This paper presents a technical description of an experimental procedure developed for the geotechnical characterization of granular soils conditioned for EPB tunneling using a modified direct shear box. As the main concerning parameters of the conditioned soil mass were their undrained properties, in order to preserve its pseudo-fluid characteristics, a watertight direct shear apparatus was constructed. A comparison between the results obtained under dry, saturated and conditioned conditions is presented. INTRODUCTION EPB shield machines have been used for tunneling excavation in many different types of soils thanks to the use of soil conditioning agents. These modify the properties of the soil into that of a plastic paste, thus permitting the homogeneous flow of the excavated soil from the tunnel face through the bulk chamber, the screw conveyor and finally the conveyor belt. Moreover this technique allows controlling the face pressure and its regulation in the bulk chamber, preventing water inflow when tunneling below the water table. Further advantages are a drop of the cutter head and screw conveyor torque and reduction of the friction between metallic parts and the soil, consequently reducing wear phenomena (Merritt & Mair, 2006; Vinai et al., 2007; Borio et al., 2010; Thewes & Budach, 2010; Herrenknecht et al., 2011; Barbero et al., 2012; Peila, 2014). Several studies have investigated the possibility of conditioning and the chemical materials to be used in different types of soils, mainly subdivided into three groups: cohesionless soils (sand and gravel), silts and clays, and rock masses. This various researches have set up several laboratory procedures for these achievements before and after soil conditioning, as stated in Thewes & Budach (2010) and Peila (2014) (for cohesionless soils), in Thewes & Burger (2005), Hollmann & Thewes (2013), Zumsteg et al.(2012) (for clay), in Peila et al. (2013) and Martinelli et al. (2015a) (for rock mass). Such tests should be simple to execute, reliable and easy to interpret at the in-situ excavation step. The reduction of shear strength is necessary in EPB operations, since it allows an effective transmission of the pressure from the material itself to the front. In some cases the slump is not sufficient to return a reliable result on the shear strength reduction, as in some cases some materials are behaving differently. Therefore this research is aimed to study this aspect more in detail, in order to show the effectiveness of the soil conditioning process on the material to be excavated."

Jan 1, 2016

By S. G. Britton

"INTRODUCTION Strategies to improve performance in mining production, maintenance and mineral processing operations has evolved over time from straightforward time studies of individual machine performance in the 1960’s-1970’s to more sophisticated and better focused statistical and financial tools that have emerged in the 1980’s-1990’s . These newer strategies fall under the broad descriptive category of “Operational Excellence”. Operational Excellence is the term that embodies a number of performance evaluating strategies, the most popular and relevant to mining includes the following: • Six sigma for addressing errors within mining or milling process and work standards • Lean manufacturing to optimize organizational and operational performance through continuous improvement. There are other strategies that can be applied as well and this paper is not focused on a review of the pros and cons of any one strategy. However, the common threads in these strategies embody the expectation that expected results from these efforts can be quantified and that value will positively benefit the targeted work process, organizational unit, equipment deployment or time schedule when applied to it as part of continuous improvement efforts. The priority for proceeding with any one or more of these efforts is based on the calculated net value of the required resources to affect the change versus the estimated value gained. The practice is identified as the value mapping process. This discussion summarizes the value mapping process methodology used at a mature uranium mine and mill in northern Canada to work through the myriad of potential improvement efforts available through the operational excellence process for continuous improvement.THE RABBIT LAKE MINE AND MILL The Rabbit Lake Mine and Mill are located in northern Saskatchewan, Canada on the shores of Wollaston Lake (Figure 1).The mine was discovered in the mid-1960s and was built by Gulf Minerals, Ltd. The mill began processing uranium ore into yellowcake in 1975 from an adjacent open pit mine. A whole ore acid leaching followed by solvent extraction and precipitation forms the basic milling processes. The operation continued to produce yellowcake through a succession of open pits and finally opened an underground mine in the early 1990s. Since beginning production, over 200 million pounds of yellowcake has been packaged from the site, making it the sixth highest producing uranium mine of all time."

Jan 1, 2016

By C. I. Wilmot

FMC's Paradise Peak Mine was discovered in July 1983. The deposit at discovery contained 11,340 ,000 tonnes (12,500,000 tons) of ore grading 3.71 glt (0.108 oz/ton) Au and 120 glt (3.5 oz/ton) Ag. A feasibility study was completed by Davy McKee in May 1984, with detailed engineering starting in June 1984. Construction of the facility started on January 2, 1985 with plant start-up taking place on April 14, 1986, two and one half months ahead of schedule and more than 10% under budget. This paper describes the status of the operation approximately 1-1/2 years after start-up including revisions and additions to equipment and process.

Jan 1, 1988

By T. J. McKeon

Gravity separators such as spirals are commonly used in multistage cleaning and scavenging circuits to improve the quality and recovery of concentrates produced in the industrial minerals industry. Unfortunately, field surveys suggest that many industrial operations are poorly configured in terms of equipment layout. This shortcoming can often be attributed to a failure by engineers to make use of fundamental process engineering tools for circuit design. One of the most important of these is linear circuit analysis. This powerful tool makes it possible to mathematically compare the relative efficiency of circuit configurations in advance of experimental testing. This article provides a basic review of the linear circuit analysis concept and discusses some of the key insights it provides for the layout of multistage circuits. An industrial case study is provided to show the tremendous impact that this process engineering tool can have on the design of multistage spiral circuits in a heavy mineral wet plant.

Feb 1, 2012

By D. F. Cater

The Macassa Mine is a mature mine with a 61 year history of continuous production. The majority of past production has been derived from a zone called the '04 Break (Main Break). Recent underground mine exploration has been successful in locating several neighbouring ninera1ized zones. This paper will characterize the spatial location, geometry and mineralogical properties of these secondary zones. Future plans for underground mine exploration to follow-up on these target zones will be outlined.

Jan 1, 1995

Shallow ore deposits are mined by surface methods but a depth is reached in the case of most deposits after which underground methods are applied for the extraction of the remaining ore. The determination of this depth and its analysis is the subject of this paper. In order to determine transition depth from open-pit to underground mining on the basis of the allowable and economically feasible overall stripping ratios, an economic-mathematical equation is first introduced. Using the achieved equation and an analytical procedure on a particular two-dimensional hypothetical tabulate deposit, an effective formula is then established. The formula introduced here, together with the procedure adopted, could be used in all similar mining situations by the mining design engineer.

Jan 1, 2010

By B. Campbell

This paper will detail the successful construction methods of a 20- foot diameter wet well shaft, approximately 180 feet deep in overall depth and 150-feet below the water table, adjacent to Lake Nacimiento, in San Luis Obispo County, California. In addition to this, highlights will include the selection process in determining the most economical support of excavation, while minimizing risk of large water inflows as indicated in the Owner?s Geotechnical Baseline Report (GBR).

Jan 1, 2010

By Paul Schmidt, John Barber

This paper discusses the determination of cutoff grade (COG), including all revenue and cost factors and how to apply the COG in the world of engineering studies and mine planning for underground mines. It provides the engineer with important considerations and practical methods to establish COG and methods of using the COG in the work of mine planning, including the application of Mineable Stope Optimizer (MSO) software which is available on several 3D mine planning packages.

Feb 1, 2024

By Eoin Murphy, Stephen Beauchamp, Steven Cowell

"INTRODUCTION Electrification of the heavily trafficked Manchester to Preston route by Network Rail required the rehabilitation of the Victorian era Farnworth Tunnels to accommodate 21st century high speed trains. Network Rail, J. Murphy and Sons Ltd (JMS) and OTB Engineering Ltd (OTB) collaborated closely to complete these works in close proximity to heritage infrastructure whilst maintaining a rail service on the route. This significant challenge has been mastered by a combination of detailed investigation, complex modelling, robust design, extensive monitoring, ground treatment, secant piling, sprayed concrete, steel arches and segmental lining techniques. Investigation of the “Down” Tunnel found deformation and cracking of the lining and this was reconstructed during 11 weekend possessions. The “Up” Tunnel was filled with low strength concrete and a 9m diameter open face shield was used to construct an 8m diameter segmental lined tunnel during a 23 week blockade whilst traffic was maintained in the “Down” Tunnel. ELECTRIFICATION OF THE RAILWAY The Farnworth Tunnel project is part of the UK wide £1bn Railway Upgrade Plan to provide improvements throughout the rail network which includes the Manchester to Preston route. The project also supports the UK Government commitment to build a “Northern Powerhouse” by improving links that bind northern England together and which will help it release its full potential with a more balanced, healthier economy. The majority of the current UK rail network infrastructure resulted from the rapid growth of the railways in the mid to late 19th century which means that most of the existing tunnels are over 120 years old. Over the centuries the introduction of larger rolling stock has reduced the original clearances provided in tunnels. The electrification of a route requires that any over-line structures provide clearance for Overhead Line Equipment (OLE), new rolling stock and to meet modern standards. As part of Network Rail’s current electrification programme a further 36 tunnels have been identified on routes requiring electrification. Not of all these Victorian structures will require alterations to provide OLE clearance but the condition of the existing tunnels and modern fire / waterproofing requirements may ultimately dictate the need for rehabilitation."

Jan 1, 2016

By V. Svalbonas

When the Trelleborg Divisions of Boliden Allis and MPSI merged, a unique opportunity occurred for two independent mill fabricators to compare various design procedures and the research upon which they were based. This paper documents such a comparison in the structural design area. Several SAG mill analyses are compared using both Boliden Allis and MPSI methods. The differences and similarities are then utilized in a correlation of critical stress definitions and the acceptable design and inspection criteria.

Jan 1, 1992

By T. Lupek, M. Buxton, A. de Jong

"With regard to the EU funded project ‘Real-Time Mining’ a sensor-based acquisition, collection and transmission of data for the resource extraction process will be developed. The key concept promotes the change in paradigm from a discontinuous to a continuous process monitoring. Especially concerning material characterization, machine performance and underground positioning ‘Real-Time Mining’ will provide sensor solutions as well as the interfaces for integration, management and visualization of the collected data for a permanent updating process of the resource model with the aim of near real-time optimization of decisions. On the basis of ‘Real-Time Mining’-Output a permanent monitoring of costs can be performed as well in both, the installation and the production process of a mine. Due to the collected data in terms of machine performance connected with the underground positioning information added with personnel tracking and mine surveys a comprehensive overview of process performance is available. By evaluating those information in a specific manner costs per unit will arise for monitoring and possibly controlling actions. INTRODUCTION By having a look into the future of mineral extraction projects, a new challenge for the Ore Mining Industry will arise in the short and medium term. Due to the depletion of currently mined mineral reserves in addition to the persistently high demand of mineral raw materials, the extraction of complex reserves will be necessary. By characterizing such deposits as not constantly graded and geometrically varying, the extraction process, especially concerning the requirement of a minimized zero-value material handling, will become economically ineffective by utilizing the traditional mineral resource management methods. Regarding the state-of-the-art mineral resource management process along the mining value chain, an intermitted, discontinuous sequence of actions is applied (Figure 1). Recently data will be collected from drill hole cores. These rock samples are analyzed in a laboratory. Based on those analyses a resource model is created whereby unknown data between drill holes is interpolated. This resource model is the basis for all mine planning actions including the selection of the mining method, extraction sequencing and the prediction of the expected performance. With the start of the production, real conditions (concentrations of elements, hardness, stability, etc.) can be observed and measured. As the production process is running accordingly to the above described mine plan, the verification of the initial assumptions happens at the earliest after processing of the extracted material. Even if deviations between the predicted and the actual performance are now recognized, the execution of corrective actions is not possible anymore."

Jan 1, 2016

By M. Niec

Lignite deposits in Poland occur within clastic Tertiary series at the depth suitable for opencast mining. Aboundant aquifers with the good quality waters that should be protected against contamination or depletion often accompany them. Landscape and underground water protection are the main regional environ-mental factors that limit the possibility of exploration and mining; presented on map of lignite bearing series distribution allow to delimit areas "free" for exploration and mining and areas where some limitations can be met up to no admittance of any industrial activity.

Jan 1, 1994

By D. K. Adjei, G. Ofori-Sarpong, R. K. Amankwah

"Mercury (Hg) is toxic and has long-term effect on the muscle tissues, the brain and the central nervous system functions due to its bioaccumulation and biotransformation effect. Hg pollution around the world is high and this has attracted much global concern such as the Minamata Convention on Mercury, held in 2013. For several years, mercury has been the chemical of choice for Artisanal and Small-Scale Mining (ASM) gold extraction, accounting for about one-third of the global mercury consumption. A greater percentage of this ends up in the environment through open burning of amalgam, spillage and indiscriminate disposal of waste. To break this wall of mercury pollution, it is very important for the mercury used to be recycled through the use of mercury retort units. This brings into the limelight, the Lantern Retort which tries to synergise the high conductivity of steel and the see-through effect of glass, thus, improving the amalgamation process. A research conducted on improving the original Lantern Retort arrived at an appropriate distillation length of 5.08 cm which was used in redesigning a more efficient retort. The improved Lantern Retort recovered about 98% of the mercury used. INTRODUCTION Artisanal and Small-scale mining (ASM) is an informal mining activities which employ quite simple tools such as pickaxes, sluice boxes, shovels, chisels, metal bars, mattocks and water pumps for mining and processing of gold ores. The artisanal and small-scale mining (ASM) sector has served as source of employment for many people in developing countries including Ghana (Aryee, 2001; Hilson and Potter, 2003; Amankwah and Anim-Sackey, 2004; Amankwah et al., 2010) and has provided a substantial amount of foreign exchange through its activities (Hilson, 2001; Styles et al., 2010). Hentschel et al. in 2003 estimated that about thirteen (13) million people are said to be engaged directly in the small-scale mining activities worldwide. However, an estimated 100 million people are said to depend on this sector for their livelihood mainly in developing countries. In China alone, a projected number between 3 and 15 million people are engaged in artisanal and small-scale mining activities (Hentschel et al., 2003), whilst in Ghana, it is estimated that more than 1,000,000 people are employed directly or indirectly in the artisanal and small-scale mining activities, with 10% being women (Amankwah and Anim-Sackey, 2004; Amankwah and Ofori-Sarpong, 2014). In Ghana, ASM gold production has grown from a low of 2.2% in 1989 to a high of 34% in 2014. This figure is estimated to increase with proper documentation. This indicates that the sector has made significant socioeconomic impact on many individuals and communities as a whole. Notwithstanding the above positive contributions, the sector has also contributed to negative impacts on human, aquatic life and the environment in general due to indiscriminate mercury emission. This ‘pollution wall’ needs to be broken, and several interventions have been put in place including the use of retort units like the lantern retort (Adjei et al., 2014; Amankwah and Ofori-Sarpong, 2014)."

Jan 1, 2017

By M. R. Grundy

The Robinson project is based on the porphyry copper and gold deposits in the Robinson Mining District, near Ely in Eastern Nevada. The district was mined from the late nineteenth century to 1978 by Kennecott Copper Corporation and its predecessors. Operations ceased when falling copper prices in the late 1970's made their outdated mill and smelter complex at McGill uneconomical. In October 1991, Magma Copper Company (Magma) acquired the many claims that cover the known porphyry copper deposits in the district These occupy a disturbed area about nine miles long and three miles wide between the towns of Ely and Ruth. Magma proposes to build a copper / gold mine and concentrator and expand the existing gold leaching facilities. Several pits, previously mined by Kennecott Copper Corporation, will be enlarged; the use of larger, more modem equipment will result in higher productivity and lower operating costs in general. ICF Kaiser Engineers, of Oakland, California, were awarded the con-tract for detailed design of the process facilities, which was essentially complete by the end of 1993. The project at present is awaiting completion of the environmental permitting process; state air and water permits are in hand, and the Bureau of Land Management's (BLM) current schedule indicates that the final obstacles to construction will be cleared by early fall of this year.

Jan 1, 1994

China's coal energy development, characteristics and relationships with atmospheric pollution are reported. Atmospheric pollution sources from coal combustion are analyzed. Some of the projects for clean coal combustion in the Shanghai area include use of industrial briquettes, investigation of coal combustion additives, and blending combustion of coal with industrial wastes. Coal is China's main energy source, and 80 percent of China's annual coal production is used in combustion devices. Coal-flue gases from the domestic stoves and industrial furnaces are the main atmospheric pollution source. China's atmospheric pollution is, in fact, the pollution of coal-flue gases. To 2000, in view of China's energy needs as a developing nation, the atmospheric pollution from coal combustion must receive our utmost attention.

Jan 1, 1994

By M. Javier

Mining is most vital to our civilization. The current model of extraction technologies was designed without an expiration date and therefore generates environmental effects that are severe. Mining results-effects have been traditionally accepted and promoted around the world since Agricola described mining. Mining’s extractive technology is outmoded and standardized and inflicts negative results-effects on nature. Those results are liabilities dimensioned in legacy and type of nature able to provide to the next generation. In order to design, build, and transform mining effectively we must ask: What is the vision of mining? Mining has exhausted its antiquated mindset of over 200 years. Now it merely pilots us into crisis. The challenge today is to resolve the socio-environmental conflicts globally with a radical transformation of the mining business at its core. This paper illustrates that old mindsets must be radically updated or the concept of mining will continue to be trapped. Changing the mindset will enable discourse toward a new destiny. These changes will change mining for the better. We are able to evolve and get different results than in the past by pursuing a new legacy to live in harmony with nature for many more years. INTRODUCTION Minerals are supported by the law of conservation of mass. They have the unique characteristics of being finite, exhaustible, unsustainable, and have an unlimited recycling. Minerals are also hard to find because we have explored and virtually exhausted the whole crust of this planet. Orebodies that used to be considered world class are almost exhausted. In the short-term, it would be almost impossible to find new world class orebodies unless they could be extracted from the ocean, the moon or other planets like Mars. Mining is designed to extract minerals for profit and to keep civilizations functioning. Subsequently, mining has a social issue that is an economic issue. Thus, mining must be seen as a real and urgent subject matter that must be protected in thought and in fact. The actual mining extractive technologies produce disequilibrium in nature that has unknowable effects in the course of time. History is filled with the negative consequences to nature due to the model of mining. The evidence of these effects from mining’s model is apparent in repetitive liabilities around the world. The effects negatively impact nature without any consideration to how these impacts will manifest themselves in the future. This model of mining is widespread and extolled in every corner of the planet because it is old and familiar and although wasteful and outdated, we do not want to expend financial resources from profit or elsewhere to explore newer ideas, methods, or technologies that would help us keep a sustainable harmony between extraction and nature. We need a new vision for mining today and to explore in what way academia can and must play a social role in the teaching of mining methods. We need to question why we continue to support the old model of mining and to ask ourselves what prevents us from updating and modernizing the method of mining to meet the current needs not just of civilization but the urgent needs to undo some of the damage to the earth. This paper hopes to develop a method to change our minds about how we conduct the business of mining in order to control the destiny of it.

Jan 1, 2019

By Eckl, Martin, Stefan Lemke, Martin Londschien

"Tunnels are built with a design life expectancy of over 100 years. One key component of such a design is the waterproofing system, which must reliably fulfil its function during the whole service lifetime of the tunnel structure. This paper deals with the determination of test criteria for the durability assessment of geosynthetic products in tunnel sealing systems. Hereby the understanding of the individual aging processes is crucial along with the long-term experience with these materials to ensure the transfer of the laboratory results and performance to site practice (test calibration) and vice versa. To verify the results of the new test procedure the material properties of geosynthetic products samples removed from older tunnels are investigated. Based on the presented results of the still ongoing research programs some preliminary conclusion regarding the updating of regulations for tunnel sealing systems are given. INTRODUCTION Watertightness is directly related to the durability and serviceability of the concrete lining. Therefore, modern traffic tunnels and shafts (Figure 1) are generally protected against mountain/ground water and water penetrating through rock fissures by a sealing system, for example with a loose-laid polymeric sheet membrane. Hereby the waterproofing sealing systems must be reliably fulfilling their function during the whole service life of the tunnel structure, regularly of more than 100 years. In consequence, the quality and lifetime performance of the waterproofing materials—beside the correct professional and careful installation in a tunnel infrastructure, is of great importance. The challenge for the industry, owners, operators and designers is ultimately the development of qualification testing and requirements (acceptance criteria) for products to ensure the design lifetime performance. Hereby the qualification procedure is seen as a routine integrated in standards, norms or guidelines, wherein test procedures should cover typical environments for the specific application fields. Polymeric synthetic raw materials are increasingly used in products with long service lifetimes (e.g. in injections, gaskets, waterbars, spray-applied and sheet waterproofing membranes). During service they are subjected to chemical (e.g. oxidation processes) and physical (e.g. changes in morphology) influences from the environment, which affect their mechanical properties—and they age. Hereby organic materials are more affected than inorganic materials. Also, polymers show strongly temperature-dependent properties compared with other construction materials. However, their long-term aging behavior is not given per se and has to be explored extensively by suitable tests, which simulate—under accelerated processes—real exposures and loads. Hereby the understanding of the individual aging processes is crucial along with the long-term experience with these materials to ensure the transfer of the laboratory results and performance to site practice (test calibration) and vice versa."

Jan 1, 2016