Search Documents

By P. Schmieder

"The close vicinity of mining companies to other sites that are used for commercial and residential purposes or to areas under conservation as well as the fact that the people become more and more sensitive to emissions have led to a negative attitude towards mining operations in the neighborhood. It is above all the use of drilling and blasting techniques that give rise to objections, in the course of which demands for more environmentally-friendly production methods have been voiced. It is in this context that production methods without the use of explosives are considered as an option. After all, the use of such production methods is the only alternative for some quarry operators. The question is what are the true benefits of these techniques and what is the relation between a possible improvement of the environmental effects on the one hand and the technological potential as well as the costs on the other. It is intended to assess the mining techniques for solid rock in their entirety. This paper will therefore look at the aspects for assessing mining techniques in the context of their environmental impact and the costs."

Jan 1, 2005

By Naeimeh Shabani, Hamid Mirzaie, Javid Sadeghi, Hoda Jafarizadeh-Malmiri, Afshin Javadi

Iron oxide nanoparticles (Fe3O4 NPs), despite their small size, are stable and have a large surface area that allows for absorption and removal of ions as well as turbidity in a short period of time. Thus, the present study addressed the synthesis and characterization of Fe3O4 NPs synthesized using the co-precipitation method and evaluated their effect on the coagulation process in water treatment. The Fe3O4 NPs characteristics were evaluated as follows: magnetic properties were measured using a vibrating sample magnetometer (VSM), surface area using Brunauer–Emmett–Teller (BET), crystal phase using X-ray diffraction (XRD), and morphology using field emission scanning electron microscopy (FESEM). In addition, the effects of the synthetic Fe3O4 NPs on the turbidity reduction of water in various pH levels were evaluated. The synthesized Fe3O4 NPs were without any impurity in the sizes of 22–32 nm, surface area of 99.6 m2/g, pores’ mean diameter size of approximately 10.6 nm, and maximum magnetic saturation of 66.21 emu/gram (emu/g). Using 0.2 g of synthetic Fe3O4 NPs with an initial turbidity of 17 NTU and pH of 6 could reduce all water turbidity (100%). Considering the cheap and facile production and separation, as well as the possibility to reuse them and reduce the sludge water content, iron oxide Fe3O4 NPs can be effectively used for turbidity reduction in the water treatment process.

Oct 26, 2020

By R. Brown, A. J. S. Spearing, M. Treinen, M. Theisinger

The mining and use of coal creates a significant amount of waste material that needs to be safely disposed of. It is likely that in the medium term, the Environmental Protection Agency (EPA) in the U.S. will categorize all such products as a new category – special waste. This would make the materials subject to many of the requirements for handling toxic waste, which will complicate the disposal of such products and significantly increase the disposal costs. Underground disposal would, therefore, seem to be the obvious solution, especially if the placed material can have low or no permeability, so that water table pollution does not present a serious long-term issue after placement. Significant additional advantages could be derived from this backfilling, including the reduction or elimination of surface subsidence, increased extraction, reduced surface waste disposal footprint and the elimination of explosion-proof seals in worked out areas. The research using a specific coal waste product as a typical example proved that the method of placing the backfill at a high density with low permeability is technically viable, but it must be made more cost effective and the other potential benefits quantified and costed in order to present a true comparison.

Jan 1, 2010

By Ananta L. Yennamani

Blast movement measurement (BMM) transmitters are a practical method to measure three-dimensional (3D) rock movement because of blasting. The BMM transmitters are activated, programmed and installed in specially designed drill holes prior to the blast and the BMM detector locates the transmitters after the blast. The BMM software then calculates and summarizes the 3D movement of each BMM transmitter ball. This information helps to redefine the ore and waste boundaries and enables improved ore and waste selection, resulting in a genuine step change in grade control. The BMM program was carried out at Newmont Mining Corp.?s Phoenix Mine, in northern Nevada near the town of Battle Mountain. The mine is in a historic mining district that contains gold, silver and copper. The geology of the pit consists of different formations made up of sandstone, siltstone, limestone, chert-pebble conglomerate, shale, skarn and quartzite, to name a few. Some of the rock is extremely hard and a powder factor of up to 0.5 kg/t (1 lb/st) is required to get adequate fragmentation to ensure sufficient throughput through the crusher and the mill. The result of using such a high powder factor translates into considerable blast movement and heave. This movement means that the ore/waste digging polygons estimated by the ore control engineer from sampling the initial blast holes will no longer be located in their original posi-tions. The purpose of this project was to test the measurement method and to see if locating the digging polygons in the broken muck pile and excavating to those polygons will improve grade control through the mill. Case studies (Zhang, 1994), (Taylor, 1995), (Gilbride, 1995), (Harris, 1997), (Taylor, 2003), Barrick Goldstrike (Gold-strike Mine, 2008), Ruby Hill Mine (Hilkewich, 2009), (Porcupine Mine, 2005) and (Aguirre, 2010) have shown that, by accounting for the blast movement, there is a potential to increase mineral recovery by as much as 25 percent for individual blasts for only a modest cost increase.

Jan 1, 2011

By Mary Nelima Ondiaka, Kayode Henry Talabi, Oladunni Oyelola Alabi, Fatai Olufemi Aramide, Francis Gitau

Iron ore is essential in steel making; however, high-grade ores have diminished, making low-grade ores inevitable. These lowgrade iron ores need further beneficiation to upgrade the iron content. Currently, traditional physical and chemical methods are utilized and are not environmentally friendly. Bio-beneficiation techniques have emerged as a sustainable alternative for mineral recovery. This review delves into recent bio-beneficiation advancements for enhanced low-grade iron ore recovery using microbes. Research has revealed that bio-beneficiation methods such as bio-leaching, bio-flotation, and bio-flocculation have proven successful in iron recovery from ores. The bio-beneficiation process occurs in mild conditions using bio-reagents derived from microbes and offers a reduction of chemicals used in processing. Bio-beneficiation of iron ore potentially offers a relatively energy-efficient, cost-effective, and environmentally friendly method of maximum iron ore recovery. However, this review has identified a scaling-up difficulty in which a future approach for industrial-use applications is offered following a thorough sustainability assessment. Bio-beneficiation, using microbial processes, provides a viable avenue for maximizing iron ore recovery while tackling the constraints of dwindling high-grade iron ore resources and environmental sustainability.

Mar 16, 2024

By Inoka E. Perera, Robert Hildebrandt, Gerrit V. R. Goodman, Krzysztof Cybulski, Zdzisław Dyduch, Michael J. Sapko, Marcia L. Harris

To prevent coal dust explosion propagations, rock dust needs to be lifted and suspended in the air with the coal dust during an explosion. The addition of anti-caking agents prevents caking of rock dust in the presence of water. Mining and rock dusting processes can frequently create alternating layers of rock dust and float coal dust on mine surfaces. For this test series, a thin layer of coal dust was distributed on top of a layer of either treated or non-treated rock dust in the Experimental Mine Barbara, Poland. The experimental results compare the effectiveness of treated and non-treated rock dusts to attenuate a propagating coal dust explosion initiated with either strong or weak methane explosions. Experimental results indicate that the treated rock dust performs better than non-treated rock dust in arresting a propagating explosion, especially in the presence of moisture.

Jan 20, 2020

By S. I. Angadi, C. Eswaraiah, Sunil Kumar Tripathy, T. Santosh, Nilima Dash

Banded hematite quartzite (BHQ) and banded hematite jasper (BHJ) ores represent a promising potential iron ore resource in the near future. The hematite and quartz in BHQ and the hematite and jasper in BHJ are closely related and require fine grinding for the liberation of hematite phases. The present study investigates the mineralogical features and comminution properties of BHQ and BHJ ores. In the BHQ ore, it is observed that thick bands of hematite have fine inclusions of silicate minerals, whereas silica bands have few grains of iron-bearing minerals. The hematite and quartz minerals in the iron and silicate bands of the BHJ ore appear to be more intricately associated and complex in nature, presenting difficulties for liberation. Bond work index studies were carried out for the BHQ and BHJ ores with different product fineness in order to evaluate the energy requirements in fine grinding. A higher Bond work index value was found for the BHJ ore (15.4 kWh/ton) than for the BHQ ore (12.4 kWh/ton). A decrease in the product particle size was associated with an increase in the work index value. Single-particle breakage experiments were designed by varying feed particle size and input energy. The specific energy consumption for the BHJ ore was higher than that for the BHQ ore. The comminution parameters showed that the BHJ ore is harder to grind than the BHQ ore, which may be due to the mineral composition and association of hematite phases with the silicates.

By Andrew B. Pervis

With the ever increasing demand for Finer powders by industry there has been a continuing effort by air classifier manufacturers to improve and offer machinery capable of producing these fine powders. Common to these classifiers is the use of a multivaned rotor through which passes all of the air used to transport the particles to be classified. Rotor revolutions per minute and the amount of air passing through the rotor are the main variables in determining the particle sizes which will be able to pass through the spinning rotor. A simplified equation derived by setting the air drag force carrying a particle through the rotor equal to the centrifugal force due to the spinning rotor's action on the entering air and particle is: Diameter of Particle = [ ] Where K is a function of air viscosity, particle configuration, rotor and blade configuration; RPM is rotor revolutions per minute; M3/sec. is air quantity passing through the openings between the rotor blades.

Jan 1, 1983

By G. Velarde

This paper presents the metallurgical results of column and stockpile leach tests with forced aeration to determine the usefulness of this process in the operational leaching at Sociedad Minera Cerro Verde S.A.A. The evolution of the aeration system is presented and also an innovative solution developed to overcome forced aeration’s main problem, which is the early obstruction of the aeration pipes located at the base of the stockpile, causing a decrease in air and oxygen levels and therefore a reduction in the metallurgical benefits.

Jan 1, 2006

By Robert Burgess, Dale Gill, Jaco Steyn, Bill Kyslinger

"With mining, especially coal extraction, comes the necessity of supporting the roof. Since the 1950s, the primary method for roof support has been the use of roof bolts. Roof bolting is considered one of the most hazardous jobs in underground coal mining. In 2004, there were 3,405 injuries reported to the U.S. Mine Safety and Health Administration (MSHA). Of those injuries, 17 percent were associated with bolting machines (593 injuries). The majority of the injuries resulted from rock falling from supported roof. However, injuries involving a part of the body being struck by, or caught between, during bolting and drilling occurred with relatively high frequency (Burgess and Steiner, 2007).Roof drilling and bolt installation is labor-intensive and repetitive. These labor-intensive and repetitive requirements can lead to cumulative trauma. Operators are expected to perform a considerable amount of lifting, carrying, bending, reaching and stretching. Back and shoulders become sore from bending and twisting to install bolts or lift and position drill steels, wrenches and bolts. Confined operator spaces also contribute to difficult and awkward working positions for the operators (Cornelius and Turin, 1998).In South Africa, the majority of the roof bolting machines used are “man-in-position” style machines (Fig. 1). This puts the operator in close proximity to where the drilling and bolting process is performed. When proper operation procedures are followed, it has been proven to be a very effective, productive and safe system. The MSHA-certified automatic temporary roof support (ATRS), canopies and dust collection system of Fletcher bolters all provide the operator with unparalleled protection. However, there are some occupational hazards inherent to the zone located next to the drilling and bolting zone. This has led some customers to request relocating the operator away from this zone. The idea being that the operators will no longer be located in the face area, greatly reducing their exposure to dust, noise, machine and geological hazards."

Mar 1, 2017

By L. Maday, V. J. Perrone, M. B. Gilbert

INTRODUCTION The Brightwater conveyance system project in King County, Washington consists of constructing about 21 km (13 mile) of effluent and combined influent and effluent tunnels. The influent tunnels will collect sanitary sewerage from the service area and convey it to the new wastewater treatment plant (WTP) site at Route 9 in Woodinville, Snohomish County, Washington. The effluent tunnels will convey treated effluent from the WTP to an outfall at Puget Sound. The tunnels will be constructed primarily under residential areas, busy suburban roads and state highways. This 21 Km (13-mile) soft ground tunneling project faced many design challenges because of the geologic and hydrostatic conditions, long tunnel reaches, and large overburden depths. Boring depths typically varied from 45.7 M (150 ft) to 114 M(375 ft) with a maximum depth of 185.6 M (566 ft) deep. Conventional empirical methods for non-mountain terrain based on a 1:1 ratio of drilled footage per foot of tunnel bore (National Research Council, 1984) for evenly spaced borings provided a good start for the Phase 1 explorations. However a continuation of this approach with closer spacing was deemed inadequate by the geotechnical team for efficiently allocating geotechnical exploration resources for the final design. This paper presents a rational approach that was used to evaluate the value of a particular geotechnical exploration boring, pump test or other in-situ test. The method of analysis, which was initially developed for rock tunnels (Einstein et al., 1978), was modified for the Brightwater project. The method considers the potential construction cost risks resulting from variable geologic conditions, the cost and reliability of the geotechnical exploration and the earned value (cost risk reduction) of performing the geotechnical exploration. PROJECT DESCRIPTION In total the land portion of the conveyance system will include approximately21 Km (13 miles) of tunnels ranging in size from 3.0 to 5.2 M (10 to 17 ft) minimum inside diameter with overburden depths of 30.0 to 168 M (100 to 550 ft) and

Jan 1, 2005

By Jens Gutzmer, Helmut Mischo, George Barakos

"It has been nearly eight years since rare-earth elements (REE) became the subject of frontpage headlines. It was when the controversial Chinese export policy for these critical commodities was epitomized in a maritime border dispute with Japan in September 2010 that resulted in the big REE crisis and price spike of 2011 (Barakos et al., 2016c; Mancheri, 2015).The world was dismayed, especially in REE-importing countries such as the United States that was, and still is, totally dependent on Chinese production and exports (Barakos et al, 2016c; Kennedy, 2015). The short-lived alarm initiated a treasure hunt by way of exploration for REE deposits all over the world. The continuously growing demand on the one hand, and the Chinese sovereignty of the REEmarket on the other, led the rest of the world to explore their own REE resources. In just a few years, more than 400 projects were initiated to explore REE deposits outside of China (ERECON, 2015; Goodenough, 2016).The prices of REE, however, dropped rapidly in late 2017 and were in six-year lows, before the 2011 crisis (Barakos, 2017). The viability of even major established producers is being challenged, not to mention the development prospects of potential REEmarket entrants (Barakos et al., 2016b; Rollat et al., 2016). Production cutbacks and industry consolidation in China have impelled REE market experts to forecast that prices have already reached their lowest point and have nowhere to go but up (Adamas, 2015; Roskill 2015). Yet, expectations for increased REE prices are limited and drastic changes are unlikely to happen in the near future, as there is still excess supply in the overall REE market (Barakos, 2017). Nevertheless, the low prices of rare earths are not the only reason that potential producers are struggling to enter the global REE market. Among other parameters, the separation process of the individual elements seems to be the most important factor, as it is technically challenging and expensive to build and to operate."

Jan 8, 2018

By D. R. Babich, E. R. Bauer

National Institute for Occupational Safety and Health (NIOSH) researchers are conducting a cross-sectional survey of equipment noise and worker noise exposures in the mining industry. Surface and underground limestone is one commodity recently surveyed. The sound levels of mining and processing equipment were recorded to identify noise sources. Full-shift worker noise exposures were completed to determine the exposure of various occupations. This paper presents the results of the noise research conducted in both underground and surface limestone mines, detailing the equipment likely to cause worker overexposures, and the occupations experiencing overexposures. Implications for worker noise exposure reduction are also reported.

Jan 1, 2006

By Steven K. Ruggieri

Increased coal production on longwalls has brought with it higher levels of dust generation. Most U.S. longwall mining operators have difficulty complying with Federal dust standards, which are stricter than European standards. Longwall operators faced with a longwall that is "out of compliance" have implemented a variety of practices designed to reduce dust levels. Mining conditions and other important variables, however, can cause fluctuations in dust levels that may overshadow the performance of a new dust control technique. This can result in the continued use of an ineffective technique or lead to the abandonment of an effective dust control technique. No single technique can keep a longwall in compliance. Maintaining compliance requires a fundamental approach to dust control -- proper application and continued use of effective dust control techniques.

Jan 1, 1983

By C. -G. Zhang

This paper presents the results of a study on cellular acclimation of Acidithiobacillus ferrooxidans to sulfur biooxidation in terms of cells growth and changes in surface properties and morphologies of both cells and sulfur particles. The results showed that A. ferrooxidans cells were grown faster and demonstrated higher concentration in the soluble thiosulfate substrate than in nonsoluble hydrophobic S0 substrate. The results showed that A. ferrooxidans cells acclimated to the sulfur biooxidation by actively expressing some extracellular polymers substance and maybe some outer membrane proteins that modified the surface properties of both sulfur particles and the cells themselves. In addition, the results showed that the A. ferrooxidans cells were able to dynamically adsorb to or desorb from the surface of sulfur particles. The cells aggregating onto the S0 surface enhanced the use of S0 substrate by the bacteria cells. This mode may be one of the most important characteristics for the better growth and propagation of the cells in solid sulfur-containing media.

Jan 1, 2009

By Changjiang Li, Jun Yang, Qiang Fu, Xu Chang, Xing Wu, Yubing Gao

With the development of underground mining, the deformation of roadway floor has increasingly become a major constraint on the safe and efficient production of coal mines. To address the floor deformation that was caused by massive stress concentration in roadway, an innovative method based on deep-hole directional tensile blasting technology is put forward. By taking No.122108 working face in Caojiatan Coal Mine as engineering background and analyzing the mechanism of deformation, a numerical simulation and field test are carried out to verify the effect on deformation control of this technology. It is found that the deep-hole directional tensile blasting technology can actively control the fracture position of the roof in the gob area and cut off the stress transmission path, so as to relieve the stress in the roadway. And since different blasting parameters have different impacts on the stress relief effect, a numerical simulation is implemented and it is found that the stress relief effect is the best when blasting depth is set to be 32 m and the blasting angle be 60°. By applying the optimal blasting parameters to the field engineering test, it can be seen that the deep-hole directional tensile blasting technology could effectively reduce maximum stress value and stress field range of the both sides of the roadway, and make the stress field far away from the roadway, thus effectively controlling the deformation of the roadway floor. The deep-hole directional tensile blasting technology can effectively solve the problem of roadway floor deformation and can be safely applied to engineering sites.

Jun 13, 2023

By N. Arbiter

Fracture under low velocity free-fall and double impact, and under slow compression have been-investigated. The pattern of breakage and the size distribution of resulting fragments for sand-cement and glass spheres have been determined. Photoelasticity methods were used to simulate the stress distributions in free-fall impact in order to explain the observed patterns of breakage. Oblique fracture planes, occurring only in free-fall impact, develop along lines which coincide with the trajectories of principal compression as determined by mathematical analysis Breakage efficiencies for different modes of fracture were compared for both types of spheres. For the same specimen and loading system, static loading and low velocity dynamic loading induce geometrically similar stress fields resulting in reasonably similar fracture patterns and shapes of fragments.

Jan 1, 1968

By Michael Day, Paul Kos, Scott Brinton

A hydrogeologic characterization and impact analysis was performed for a proposed quarry at the Hitch Rack Ranch located in the Little Turkey Creek watershed southwest of Colorado Springs, Colorado. Continuous multiple channel tubing, nested piezometers, stream flow measurements, and mapping of known seeps were used to define the three-dimensional potentiometric distribution and areas of groundwater recharge and discharge. Water balance considerations, mass balance calculations, and potentiometric response to earth tides and barometric fluctuations confirmed that the granite fracture system in the ridge area of the proposed quarry has an extremely low bulk hydraulic conductivity resulting in minimal groundwater discharge to sustain the baseflow of Little Turkey Creek. The Little Turkey Creek valley forms the major conduit for groundwater flow exiting from the upper part of watershed underlain by granite. This conclusion has significant implications with respect to mine planning to minimize projected impacts to the hydrologic system and preserve this recharge component to downgradient Denver Basin sedimentary deposits.

"Mining used to be a business primarily focused on the technical aspects of getting valuable ore out of the ground and extracting the minerals efficiently. Without denying the importance of these skills, a narrow focus on technical issues is no longer enough to guarantee success when it comes to exploiting rare earth element (REE) deposits. Molycorp failed to enter the global REE market in a successful manner, while none of the many REE exploration projects has turned into an active mine so far and none is expected to commence operations in the near future. Accordingly, the world of REE is far more complex compared to other commodities. This paper looks into the REE industry to identify the factors that can connect potential U.S. REE mines to the market. The ability to break free from past thinking and become future-focused is a key driver. Mining of REE is pointless without a corresponding value-adding chain, while developing a value chain without first establishing an uninterruptible source of REE is also senseless. The mining sector must be based on the REE value chain and vice versa, along with the establishment of a market channel for the REE products that come out of the mine. INTRODUCTION It has been seven years since rare earth elements became the subjects of front-page headlines. It was when the controversial Chinese export policy for these critical commodities was epitomised in a maritime border dispute with Japan in September 2010 that resulted in the big REE crisis and price spike of 2011 (Barakos et al, 2016c; Mancheri, 2015). The world was dismayed, especially in REE-importing countries, such as the United States that was and is still totally dependent on Chinese production and exports (Barakos et al, 2016c; Kennedy, 2015). The short-lived alarm initiated a treasure hunt by way of exploration for REE deposits all over the world. The continuously growing demand on the one hand and the Chinese sovereignty of the REE-market on the other, led the rest of the world to explore their own REE resources. In just a few years, more than 400 projects were initiated to explore REE deposits outside of China (ERECON, 2015; Goodenough, 2016). The prices of REE, however, dropped rapidly and at the moment of writing this paper are in 6-year lows, at the level of the price average before the 2011 crisis (Barakos, 2017). The viability of even major established producers is being challenged, not to mention the development prospects of potential REE-market entrants (Barakos et al, 2016b; Rollat et al, 2016). Production cutbacks and industry consolidation in China impel REE market experts to forecast that prices have already reached their lowest point and have nowhere to go but up (Adamas, 2015; Roskill 2015). Yet, expectations for increased REE prices are limited and drastic changes are unlikely to happen in the near future, as there is still excess supply in the overall REE market (Barakos, 2017). Nevertheless, the low prices of rare earths are not the only reason that potential producers are struggling to enter the global REE market. Among other parameters, the separation of the individual elements seems to be the most important factor, as it is technically challenging and expensive to build and to operate."

Jan 1, 2018

By E. Siami-Irdemoosa, S. R. Dindarloo

Ease of excavation or rippability, also called diggability or excavatibility, is a critical decision-making parameter in the selection of both the overburden removal method and the required equipment in surface mining and geotechnical engineering projects. The most widely used method of estimating rippability is rock mass classification. Although there are different classification schemes in the literature, all of them have the two major limitations of sharp transitions at class boundaries and subjective uncertainties in decision making. In this study, the decision trees method was employed as a classification tool for estimating ground rippability, using the four rock mass parameters of weathering degree, uniaxial compressive strength, joint spacing and bedding spacing. The results were compared with those of the widely used method of diggability index rating (DIR) and a fuzzy-based DIR. The problem of subjective uncertainty was resolved in the proposed decision trees method, as the tree rules were derived automatically from the training data sets. Compared with fuzzy-DIR, a decision tree classifier is simpler, needs less computational time and is more appreciable by industry practitioners. Nevertheless, the proposed method is not flawless and, similar to both the conventional and fuzzy DIR methods, yielded poor estimations in particular instances. The limitations of the three methods are discussed.

Jan 1, 2015