Search Documents

By C. John Dunnicliff, Birger Schmidt

INTRODUCTION To be effective and useful, monitoring of tunnel construction must be carefully planned throughout all steps. A vital and frequently overlooked step is a clear definition of the specific purposes of the instrumentation. Most tunnel construction monitoring has in the past been of benefit to research, the advancement of tunneling practice, wittingly or not. The development of monitoring instrumentation for the benefit of the project from which the data are recovered has very significant potential for risk and cost reduction of soft ground tunneling. A systematic approach to tunnel construction monitoring, from conception to full implementation, includes at least the following nine tasks or steps: Definition of benefits and purposes; design and project specification to draw full benefits; selection of monitoring parameters; selection of instruments and writing of specifications for procurement and installation; procurement and installation; reading and maintenance; data storage and retrieval; interpretation; implementation. Some of these steps are fairly easy and resolved through the use of established theories and technologies. The difficult ones are those that require the bending of minds, those that involve changes in the ways engineers design soft ground tunnels, the way owners pay for tunnels, and the construction is managed, inspected and controlled. Performance monitoring can be of benefit to the owner, design

Jan 1, 1974

By Albert E. Ketler

The AirBoss*200 is a unique ambient airflow sensor with important improvements in accuracy, especially in the critical low end, 0-61 m/min (0-200 fpm) where MSHA regulations apply. All solid state, its design is rugged, and there are no moving parts or delicate filaments. An on-board microprocessor calculates air velocity, linearizes and corrects for temperature, while driving voltage and current loop analog outputs to .3 meters/minute (1 ft/min) resolution. Recent developments also cover both positive and negative flow directions. A hand held computer is available to readout data and to adjust stored range selection, alarm set points, calibration data and the speed of response. Installation in hazardous areas is covered by MSHA Classes G, H and L.

Jan 1, 1993

By Kalle Hakalehto

Automation and mechanization in mining has no value of its own. It has to be measured in economic terms or in Increased safety or in the utilization of deposits which otherwise were unavailable. The mechanization and automation of workphases in the mining and rock construction process has led to the decrease of manual work. This has had a very essential importance in the countries where the labor is expensive or where there has been difficulties in the availability of labor. The work has become much more efficient. We would like to argue that the need of mechanization has been initiated mostly from the above mentioned reasons. The origin has seldom been the "process" approach or the real need or will to change the way mining is done. Through mechanization bigger unit sizes of machines and operations have become possible and better efficiency is achieved. This has led to new problems as well, but in most cases they have been solved so that better and more economic outcome than before has been the end result. The changes have thus been justified. It is perhaps feasible to state already at this stage that we see that the mechanization andautomation steps in the difficult conditions of mining have been remarkable. There is not a slightest underestimation of the achievements and importance of this development in our mind. Where we are to- day is the result of the experience, know-how and technological excellency of all the parties involved. The natural approach to automation has been through mechanization and automation of individual unit operations and machines. This has been the way as well in manufacturing industry as in mining. There may not have been any other way. The other presentations in this session tell us very clearly of the approach .which the machine manufacturers have taken. They have not done it alone but 'most of the initiatives have come from them. A good use of their present achievements gives many possibilities to increase the, efficiency in mining. We would, however, like to extend the view one step further to the future:

Jan 1, 1989

By Corale L. Brierley

Bacteria have long been used for the extraction of copper during dump leaching of sulfide minerals and in the recovery of uranium from mined-out areas. However, bacteria can also be used in extraction of trace metals from copper ores and waste materials. Molybdenum, tungsten, nickel, cobalt, gold, silver, and other strategic metals can potentially be released from ores and wastes by biological processes. The chemistry and biology of these reactions, the potential for using the processes, and the state-of-the-art of the technology will be discussed.

Jan 1, 1983

By James L. Vanderbeek

The Chino concentrator commenced operation in 1982 as a SAG-ball mill circuit which could process 37,500 stpd of ore. Since 1982, a series of process improvements such as the addition of two stages of SAG recycle crushing, allowed throughputs to increase to more than 48,000 stpd, at the expense of significantly coarser flotation feed sizing and reduced recovery. To compensate a third (tertiary) stage of grinding consisting of four 1250 hp Vertimills was installed which has allowed the flotation feed size and recovery to return to historical levels. The design and operational characteristics of the Tertiary Grinding Circuit are described.

Jan 1, 1998

By Max John

INTRODUCTION One of the main advantages of the New Austrian Tunneling Method (NATM) is its adaptability to varying rock conditions. This method is therefore successfully applied when complex geologic features are expected which cause uncertainties in the prognosis of the rock mass behaviour, as was the care at the Arlberg Expressway Tunnel. Furthermore, by employing the NATM problems are avoided when encountering varying geologic conditions or even extension fault zones along the tunnel, as was the case at the Dalaaser Tunnel and Perjen Tunnel. The NATM can also be used for rock and soil. The following examples will show how various rock conditions can be mastered. In accordance with the NATM all tunnels which will be discussed are road tunnels having a cross section area between 70 and 100 m2. The construction consists of a primary support, which ensures stress redistribution during excavation (Figure 1). The primary support is reinforced shotcrete strengthened by steel arches, when necessary, and rock bolts. When encountering rock pressure, swelling rock or soil, the primary support is suplemented by an invert arch. The purpose of the secondary lining is to increase the safety of the tunnel with regard to long-term stress redistribution processes or changes in rock mass properties as well as to protect the insulation. The secondary lining consists of cast concrete without reinforcement and is generally 0.25 or 0.30 m thick.

Jan 1, 1981

By J. G. Groppo, B. K. Parekh

Removal of moisture from fine (minus 28 mesh) dean coal to 20 percent or lower level is difficult using the conventional vacuum dewatering technique. High pressure filtration technique provides an avenue for obtaining low moisture in fine clean coal. This paper describes a couple of novel approaches for dewatering of fine clean coal using pressure filtration which provides much lower moisture in fine clean coal than that obtained using conventional pressure filter. The approaches involve (a) split stream dewatering and (b) addition of paper pulp to the coal slurry. For Pittsburgh No. 8 coal slurry, split stream dewatering at 400 mesh provided filter cake containing 12.9 percent moisture compared to 24.9 percent obtained on the feed material. The addition of paper pulp to the slurry provided filter cake containing about 17 percent moisture.

Jan 1, 1995

By M. Abdi Oskouei

Some believe that Sustainable Mining due to impermanence of mining operation and adverse environmental impacts of mining, is an oxymoronTruly, no one can overlook these environmental impacts; however, a sustainable development is based on three elements Environmental, economical and social sustainability. In order to assess the relation between mining activities and sustainable development, not only environmental but also economical and social sustainability must be considered.Thanks to mine reclamation the adverse impact of mining on the environment can be reduced, meanwhile it will improve the social and economical condition after the mine-closureTo ensure that a mining operation is toward sustainable development goals, specific criteria and indicator frameworks have been established, in addition, for verification of our discussion the suitable selected reclamation plan for Bibishahrbanoo limestone mine of Tehran-Iran and its effect on sustainability of region has been studied.

Jan 1, 2011

By D. Marinakis

Gas hydrates (GH) are crystalline compounds consisting of a water molecule lattice, in the cages of which suitably sized molecules, such as methane or other light hydrocarbons, are confined. Although this solid phase looks similar to common ice, it contains substantial amounts of natural gas. The necessary conditions for natural gas hydrate formation exist in some deep-sea marine environments and in permafrost regions. Despite the extensive research, which has been conducted in the fields of exploration and exploitation of natural gas hydrate deposits over the last decades, there is still great uncertainty over the estimated amount of hydrates that these reserves bear. The present work examines some key features of sediments which affect their capacity to host gas hydrates. The hydrate content of a natural hydrate formation is correlated qualitatively with factors such as temperature, effective porosity, mineralogical composition, bio-surfactants, pore pressure and compaction pressure.

Jan 1, 2006

By S. P. Liebenberg

During the past fifteen years significant progress has been made on carbon-in-pulp (CIP) technology for the extraction of gold. While most research on the mechanisms and kinetics of CIP sub-processes has focused on the adsorption step only, auxiliary unit operations such as elution have received less attention. The mathematical models which have been developed for elution at the University of Stellenbosch can be used for design as well as process optimisation by incorporation into an overall CIP simulation program. Except for these models, no other comprehensive models for the complex elution process are available. It is the aim of this paper to review recent modelling work on competitive elution from activated carbon.

Jan 1, 1995

By T. C. Eisele

Previous work by the authors has shown that the performance of a flotation column can be improved by the use of horizontal baffles. These baffles prevent axial mixing and also reduce "churning" of the froth by breaking up or preventing the formation of large air bubbles. In this paper, results from tracer experiments are presented that show the effects of horizontal baffles on the reproducibility and stability of the column operation. The baffles prevent random disturbances, such as unusually large air bubbles and turbulence, from rapidly propagating along the height of the column. Because these factors are responsible for much of the variations in column performance between tests, the result is that the horizontal baffles make the column performance more reproducible, with fewer short-term variations.

Jan 1, 1999

By R. W. Henn

Introduction Shotcrete, by the American Concrete Institute definition, is mortar or concrete pneumatically projected at high velocity onto a surface. The term gunite is still common in literature. It is a trade name established by Cement Gun Co. of Allentown, PA, around 1911 for a dry mix of fine aggregate material, hydrated at the nozzle, and pneumatically projected at high velocity onto a surface. This article will discuss shotcrete applications, ingredients, mix proportioning, batching and mixing, admixtures, testing, and steel fiber vs. conventional shotcrete. Applications Shotcrete is used primarily by the mining and underground construction industries to temporarily stabilize an excavated rock surface until a permanent cover can be installed. It may also be used as the permanent covering material. Other uses include refractory material, architectural finishes, slope stability, wearing surfaces, repairing existing concrete structures, fireproofing, and corrosion protection of steel. Wet Versus Dry Process In the wet process, all ingredients, including water but not accelerator, are mixed the same way as normal concrete before its placement by pneumatic projection. The accelerator is added in a liquid state through the nozzle at the point of placement. In the dry process, all ingredients, including acceleration in dry form but not water, are mixed just before placement by pneumatic projection. Water is added through the nozzle at the point of placement. Liquid accelerator may be added at the nozzle in the dry process. Ingredients Shotcrete consists basically of the same ingredients as concrete with some limitations. Type I, II, and III cements are used. However, Type II seems to be used most in underground applications. This can be attributed to ground water at most sites having slight to moderate concentrations of sulfates. Air-entraining cement or air-entraining admixtures are generally not used in dry mix shotcrete. It is generally agreed that it is impossible to entrain air due to the absence of the usual concrete mixing action, and the high velocity of impingement of the material on the application surface. Air-entraining cement or air-entraining admixtures are used in wet mix shotcrete. Their use, however, is not widespread due to the placement method and the fact that high velocity air drives off most of the entrained air. Test results are not conclusive in showing any durability increase of shotcrete to freezing and thawing by using entrained air. In spite of current practice, the trend is toward additional research, with more agencies and owners requiring the use of entrained air. The philosophy behind this is that some entrained air is better than no entrained air to increase durability to freezing and thawing. The aggregates used in shotcrete are the same as those used in concrete. However, the largest coarse aggregate presently used is 19 mm (0.75 in.). A typical gradation requirement is shown in Table 1. The water quality requirement for shotcrete is the same as that for concrete. Accelerators are by far the most important admixture in shotcrete.

Jan 6, 1984

By R. G. L. McCready, G. Dr. Heinrich, V. I. Lakshmanan

The objective of this study was to prove repeat loading capacities of physically stabilized fungal biomass from Penicillium sp. for the removal and recovery of uranium from mine water (Denison Mines). The testwork was carried out on a bench scale in small columns and proved that it is possible to stabilize the biomass in an inorganic compound. A lifetime of 10 loading-eluting cycles of the stabilizer biomass product was obtained by additional pretreatment. Sodium carbonate proved to be an effective elution medium. Loading and elution can be controlled by the pH values of the column. The effective loading capacity until the breakthrough point is approximately 70 % of the overall loading capacity. The loading capacities of the stabilizer biomass product are comparable to that of the original biomass. Uranium recoveries of 90 to 99 % were achieved during the loading and eluting under optimized conditions. Depending on the used biomass the described process might be applicable to remove uranium or other dissolved heavy or rare metals from effluents.

Jan 1, 1989

By G. B. Misra

Heat transfer in partially wet mine airways has been the subject of study for quite some time. Of the available models some are quite empirical while some involve highly complicated computation. Models developed by Amano, Mizuta and Hiramatsu and Banerjee and Chernyak as well as that modified by Misra were evaluated for prediction of the rise in temperature and humidity (mixing ratio ) of partially wet mine airways at four different levels in the Mosaboni Mine of Hindustan Copper Ltd. Measurements of barometric pressure, virgin-rock temperature and changes in dry- and wet-bulb temperatures along a certain length of airway were made. The rise in dry-bulb temperature and mixing ratio of air over the sections were calculated using the three models. The study reveals that calculated values of temperature and moisture content agree within possible rage of experimental error with all the three models in case of three levels with low wetness factor, but the agreement was poor for the relatively more wet airway on the 30th level. Errors in the estimation of fw to the tune of 0.025 can lead to fair error up to 0.94 K in the estimated temperature while alternative ways of estimating the heat transfer coefficient [] can introduce errors up to 1.45 K.

Jan 1, 1987

By Heinrich Schubert

In many unit operations, there are more or less developed turbulent flow conditions. Then, macroturbulence influences the transport phenomena of the particles and microturbulence controls the stresses acting on fluid and solid particles or agglomerates as well as the collisions between particles. Consequently, these conditions have to betaken into consideration for modeling and optimization. The results of corresponding approaches are demonstrated taking classification and flotation as examples. But, at present, extensive simplifying assumptions have to be made.

Jan 1, 1989

By R. J. Pruett, P. I. Prescott

Ground calcium carbonate (GCC) is used in the paper, plastics, paint, rubber and caulks and sealants industries. The favorable properties of GCC include high whiteness and brightness, low hardness and outstanding rheology in water systems. The quality of calcitic GCC ores, which includes chalk, limestone and marble, is dependent on calcite purity and the nature and quantity of the impurity minerals. Wet and dry grinding are used in the processing of GCC. Ore processed by optical sorting, flotation and/or particle-size classification has higher brightness and lower abrasion characteristics. GCC markets are a function of the product's properties, purity and cost.

Jan 1, 1997

By D. J. Dunn

Grinding balls, simple in shape, are actually sophisticated machine components and essential elements of mineral grinding mills. Their physical properties and quality must be adequate to achieve design life and grinding mission with few failures. Consistent properties and freedom from breakage are essential. Size, mass, hardness profile, chemistry, and microstructure are important variables that should be designed, specified, controlled, and verified to achieve optimal mill performance. Failure to specify ball properties in detail or failure to obtain required ball properties and quality can cause milling productivity losses and excessive costs that could endanger a milling operation's survival in the competitive mineral industry.

Jan 1, 1990

By James R. Aggson, Verne E. Hooker

GENERAL CONSIDERATIONS The design of a mine or any underground opening in rock is similar to the design of any other structure, such as a building or a bridge, in one important way. This similarity lies in the fact that the stability of the structure is a function of the loads that will be applied during the structure's expected lifetime. In the case of an underground opening, the applied load is the product of the existing in situ stress field and the concentration of this field that is produced by the extraction of a load¬bearing material. Thus, a knowledge of the in situ stress field is considered a basic requirement in the design process and essential to the eventual stability of the underground structure (Duvall, 1976; Obert, 1972; Merrill and Peterson, 1961; Dahl and von Schonfeldt, 1976; Hedley and Wilson, 1975). The in situ stress field can be used along with the physical properties of the rock masses involved, the ge¬ometry of the various rock types, the geometry of the openings involved, and a failure criterion to evaluate structural stability of a planned mine by theoretical or numerical techniques. This same information can be used to investigate ground control problems in existing mines. In situ rock stress determinations can be separated into three categories: the determination of applied stress, also called the absolute or field stress; the deter¬mination of concentrations of the field stress near open¬ ings; and the determination of changes in rock stress as load-bearing material is removed. The applied stress field is more difficult to determine than are stress changes. Various instruments and techniques have been developed to determine applied rock stress and stress changes in rock. ABSOLUTE OR FIELD STRESSES Theoretical Considerations In the absence of actual measurements, it is often assumed that at any point, the vertical stress is equal to the weight of the overlying material. [ ] where S„ is vertical stress, S is average weight density of overburden rock, and h is depth from the surface. This is normally consistent with actual experience. The horizontal stresses are assumed to be equal and related to the vertical stress through the Poisson effect. [] where Sh is horizontal stress, S„ is vertical stress, and v is Poisson's ratio. The derivation of Eq. 2 is dependent on lateral con¬finement of the rock mass. An increasing amount of information is rapidly becoming available which indi¬cates that the in situ stress field at a particular location cannot simply be assumed to be a gravity-induced stress distribution in which the secondary principal stresses in the horizontal plane are due to confinement and Pois¬son's effect. Rather they can be a complex function of gravity loading, regional stresses, structural features, ex¬cavation geometries, and variations in surface and/or possibly basement rock topography. Furthermore, the underground principal stress dis¬tribution is not necessarily vertical and horizontal as is often assumed. The deviation of the three-dimensional stress distribution from vertical and horizontal can be due to a combination of both topographic (Hooker, Bickel, and Aggson, 1972) and structural features.

Jan 1, 1982

By V. Srajer

Operations research includes the application of systems analysis to mining operations, the acquisition of field data and the creation and verification of computer models of these operations. These activities result in the generation of computerized mine planning tools which have a firm base-in observational facts. The Surface Mining Laboratory of the Canada Centre for Mineral and Energy Technology (CANMET), in Devon, Alberta has been engaged in operations research activities since 1982. The work includes computer simulation of truck/shovel, continuous mining equipment and dragline operations. Other examples include cooperative programs with industry (such as the demonstration and evaluation of an integrated truck management system), the development of a device to measure off-highway truck rolling resistance, and an automated remote data transmission network. The presentation outlines existing and proposed research projects of the Operations Research group.

Jan 1, 1989

By R. M. Damodaran

The flotation performance of Florida phosphate rock was evaluated in terms of the mixing behavior of reagents and particulates during anionic conditioning of phosphate slurries. The various conditioning variables that influence mixing, namely, solids loading, agitation speed and conditioning time, were investigated to determine their effect on reagent coating of the particles. The phosphate recovery was used to monitor the conditioning efficiency. The mixing characteristics of the phosphate feed were evaluated in terms of the ratio of the mixing power (P) to the minimum power (Pm) required to keep the slurry in suspension. It was found that mixing conditions govern the conditioning time required to obtain a high recovery. Reagentization was slower at lower P/Pm ratios. At higher P/Pm ratios, the flotation recovery was optimized, and the agitation speed was found to have no significant effect. Optimum mixing conditions were obtained for a74 wt% slurry at an agitation speed of 450 rpm (47 radians/sec). Under these optimum mixing conditions, the collector dosage required for an improved recovery was lower and the conditioning time was shorter.

Jan 1, 1997