Search Documents

By Raymond A. Povirk, David L. Bartsch, James V. Hamel

The Ohio Valley Coal Company is expand- ing its Powhatan Mine No. 6 near Alledonia, Ohio. This expansion includes a 20 rn (65 ft) height in crease for an existing 44 rn (145 ft) coal refuse - slurry impoundment dam. The dam is being raised by upstream construction which will involve placement of more than 15 m (50 ft) of new fill over an existing reinforced concrete decant structure. This structure is 0.76 rn (30 in.) square inside and its deepest portion was under 24 m (80 ft) of coal slurry and water. The top of the decant structure was not strong enough to safely support the new fill and, because of the slurry and water, there was no way to reinforce the structure from the outside. The structure was reinforced frorn the inside by sliplining 73 m (240 ft) of 0.66 rn (26 in.) OD, 0.53 rn (21 in.) ID polyethylene pipe, grouting around this pipe with cellular concrete. and constructing a steel-fiber reinforced micro-silica concrete transition at the upslope end of the pipe. Rehabilition of the decant structure was completed in August 1989. The rehabilitated decant structure is now performing satisfactorily as fill is being placed over it for raising the dam.

Jan 1, 1991

By C. A. Rowland

Wet grinding rod mills have been used for 50 years to grind ores and to make specification sand. The application of wet grinding rod mills is well understood. Until recently, there have been very few installations of dry grinding rod mills. The basic principles learned from wet grinding rod mills that were used in the application of dry grinding rod mills are 1. It is possible to extrapolate the performance of 5' and 6' diameter wet grinding rod mills into larger diameter rod mills with the larger mills performing as predicted. Wet grinding rod mills as large as 14' diameter (inside shell) by 20' long using 19.5' long rods are in use operating satisfactorily. 2. Wet grinding rod mills generally grind more efficiently when the fines are left in the mill feed than when the fines are removed from the feed. 3. Wet grinding rod mills produce little tramp oversize and generally can be operated in open circuit except when very close control on the top size in the product is required. When operated in closed circuit, the circulating load is normally less than 100%. 4. The power required for the desired grind can be accurately determined from the work indices obtained from rod mill grindability tests on the material to be ground. Where required it is necessary to, apply inefficiency factors for oversize feed and for larger or smaller than normal- ratios of reduction. Recent applications for rod mills have developed where it is required that dry grinding be used. These recent applications cover the grinding of 1. Lead sinter, lead slag and limestone. 2. Iron ore. 3. Silica for making glass sand. 4. Cement clinker. 5. Coke.

Jan 1, 1968

By HASAN SERKAN GOKCEN, SERKAN CAYIRLI

The purpose of this study was to investigate the dry grindability of calcite powders in a vertically and horizontally orientable laboratory batch type stirred mill. The experimental results were evaluated using stress intensity analysis. The performance was also compared in terms of mill orientation. The results showed that the d50 values decreased with increasing stress energy down to a certain point and then increased for both milling orientations. Even though the optimum stress energies for both vertical and horizontal orientations were in the range of 1*10−3 to 5*10−3 Nm at 750 and 1500 kJ/kg energy consumption, the product size was finer for the horizontal orientation at the same stress energy value. Additionally, to the best of the authors’ knowledge, this is the first study to compare mill orientation (vertical vs. horizontal) for the same mill and under the same test conditions.

Apr 21, 2021

By Xuehui Li, Xinshuai Shi, Jun Wang, Jianguo Ning, Shang Yang, Zhaohui Zhang

Pressure relief is an important step in preventing and controlling rock burst disasters. Hydraulic slotting has emerged as a strategy for pressure relief and energy release in roadway surrounding rock. There is no qualitative description for the response relationship between hydraulic slotting parameters and the degree of pressure and energy release in a roadway, which is a scientific problem. In this paper, theoretical analysis, numerical simulation, and on-site industrial practice were comprehensively used. First, a structural model for the pressure relief and energy release of coal by hydraulic slotting in a deep roadway was established, and the pressure relief and energy release principle by hydraulic slotting was revealed. The principles and methods for determining hydraulic slotting parameters in the roadway were proposed. Three evaluation indices for the pressure relief and energy release effect of coal after hydraulic slotting were proposed, namely, the stress ratio of coal, elastic energy density ratio of coal, and displacement rate of the roadway rib. According to the evaluation indices, the degree of pressure relief and energy release was divided into three levels: reverse pressurization, full pressure relief, and transitional pressure relief. Then, a FLAC3D numerical model was constructed, the levels of pressure relief and energy release under different hydraulic slotting parameters were analyzed, and the optimal slotting parameters were determined. Finally, on-site industrial practices were carried out in Panel 7312 of the Xinhe Coal Mine. An effect test showed that the effect of pressure relief and energy release was remarkable after hydraulic slotting was adopted on the roadway surrounding rock, which can effectively reduce the risk of rock bursts. These research results can further improve hydraulic slotting technology systems and provide a theoretical basis and technical reference for the stability control of deep roadway surrounding rock.

Sep 20, 2023

By S. Chander

A review of the published literature on the mechanism of depression of sulfide minerals shows that a unified theory is not yet available. The various mechanisms that have been postulated include competition between depressants and collectors to adsorb at the surface sites, creation of thermodynamic conditions nonconducive for formation of a metal collector salt or formation of a hydrophilic coating on the surface. The hydrophilic coating may or matt not effect the adsorption of collectors. In yet another mechanism, the depressant nay participate directly in oxidation/reduction reactions between collectors and sulfide minerals. Examples from the literature are discussed to highlight oxidation/reduction effects in the depression of sulfide minerals.

Jan 1, 1984

By Paul G. Mahoney

The original Radum aggregate plant, built by Henry Kaiser in 1931, is the oldest of the nearly 200 individual operations established by the Kaiser companies. Since that time it has been producing aggregate products primarily for the San Francisco Bay Area. Currently, and for many years, this plant has been listed as the Nation's No. One aggregate producer. Early this year a new $10,000,000 facility went on line replacing the old plant. Construction of the facilities was performed under the direction of Kaiser Engineers construction management teams. The existing plant continued to operate without interruption during the entire construction period.

Jan 1, 1970

By R. E. Murray

"It is a gloomy moment in the history of our country. Not in the lifetime of most men has there been so much grave and deep apprehension; never has the future seemed so incalculable as at this time. The domestic economic situation is in chaos. Our dollar is weak throughout the world. Prices are so high as to be utterly impossible. The political cauldron seethes and bubbles with uncertainty. Russia hangs, as usual, like a cloud, dark and silent, upon the horizon. It is a solemn moment. Of our troubles, no man can see the end." By now you, no doubt, are asking, 'Where did Murray get this bit of philosophy?' Well, I obtained it from an editorial entitled. "The Worst of Times", which was published in the Harper's Magazine in 1847. That's right, 1847! The parallelism between the situation in our country at this time and in 1847 is un- canny. But wait, there is one major exception the size of government. To my knowledge, the citizens of 1847 were not stifled by the extreme governmental excesses that we are experiencing today.

Jan 1, 1980

By JOHN R. HEBERGER, MAHIYAR F. NASARWANJI, Jonisha P. Pollard, Lydia M. Kocher

nt in the mining industry, and identifying factors associated with these injuries is critical for developing prevention efforts. This study identifies nonfatal injury incidence rates, nature of injury, work activities, glove usage, and sources of hand and finger injuries in the U.S. mining industry, as reported to the Mine Safety and Health Administration (MSHA) from 2011 to 2017. Hand and finger injuries occur at a rate of 6.53 per 1,000 full-time employees, which is nearly double the rate of the next highest affected body part, the back. Most of the hand and finger injuries were classified as cuts/lacerations/punctures (53 percent) followed by bone fractures/chips (26 percent). Materials handling and maintenance/repair were common activities at the time of the incident with miscellaneous metals — such as pipe, wire and guarding — and hand tools as the primary sources of hand and finger injury. Although the information on glove use was limited, leather gloves were most often worn when an injury occurred.

By Greg Ford

Each year, companies spend millions of dollars on safety training and on safe equipment, money that is generally well spent. Despite that, we still make mistakes. What happens if the mistakes are made not because of inadequate training, but because we are hard-wired to act in a certain way? If you read any of the ?Because of Human Error? text boxes in this document, situations like these may look familiar in your own workplace. ?The issues of risk, health, safety and the environment are getting more attention now than ever before, at all levels of the organization,? said Calvin Price, vice president of Global Health and Safety at LNC-Lavalin Inc., a company with 21,000 workers worldwide. Most would agree with Price that attention to safety is increasing because responsible companies care about their workers and the workers? colleagues, families and communities. However, cynics might say that the safety spotlight is powered by the corporate bottom line. Direct costs created by workplace injuries total $51.8 billion annually and include workers? compensation payments, medical expenses, civil liability damages and litigation expenses. This sum represents a staggering one quarter of each dollar of pretax corporate profits. Indirect costs may run as much as 20 times the direct costs of on-the-job accidents and illnesses. Examples of indirect costs include training replacement employees, investigating the accident and implementing corrective measures, lost productivity, repairing damaged equipment and property, and costs associated with lower employee morale and absenteeism. What?s interesting is that up to 90 percent of incidents are due to human error, not faulty equipment or other factors.

Aug 1, 2013

By R. D. Doepker

The dissolution of metals from various metal-mine tailings has been studied through a series of submerged tailings batch tests at U.S. Bureau of Mines laboratories. Tailings selected for this study included both reactive (as determined by column leaching studies) and benign tailings. Metal mobilization in aerated (97 pct saturated with oxygen) samples appeared to be consistently greater than metal dissolution from stagnant (79 pct or 70 pct saturated with oxygen) waters. In the early weeks of the study, sulfate concentrations increased with solid-liquid contact time, while calcium dissolution remained nearly constant. Metal concentrations varied in relation to solid-liquid contact time and aeration. Leachate pH appeared to be nearly independent of solid-liquid contact time for basic tailings. Reactive tailings having both a submerged and a surface component demonstrated increased metal mobility.

Jan 1, 1990

By Matthew J. DeMarco, Anthony T. Iannacchione

Coal bumps have presented serious mining problems in the U.S. throughout the 20th Century. Fatalities and injuries have resulted when these destructive events occur at the working face. Persistent bump problems can result in abandonment of large reserves or lead to premature mine closure. Through the years, a1ternative techniques such as artificial supports, extraction sequencing, destressing, pillar design changes and specific pi1lar retreat practices have been successful1y imp1emented to mitigate coal mine bumps. Several techniques have evolved for room-and-pi1lar operations that control the way the roof rock breaks, regulating the manner in which stresses are redistributed in the mined section. Special mine layouts employed in longwall mines have also proved to be successful in safely redistributing or containing excessive loadings. However, with ever increasing production rates, greater overburdens and new mining systems, the need to evolve even more effective bump control designs will continue to challenge the U.S. coal mine industry.

Jan 1, 1992

A practical core-based method for estimating in situ stress was tested using 360° measurements of rock core diameter in a laboratory setting. In several mining districts across West Virginia, rock cores were recovered from exploration core holes and oriented using an acoustic televiewer (ATV) summary log. Measurements of diametral variation were performed at 0.1-foot depth intervals using a benchtop device comprised of a pair of diametrically opposed contact digital indicator gauges working in tandem. The diametral profiles were evaluated to determine strain direction and strain magnitude. Stress magnitudes were calculated when values for Young’s modulus, and Poisson’s ratio were available. Stress direction results are compared to other stress determination methods, including downhole overcores, drilling-induced fractures, and borehole breakouts. The testing and analytical methods used are similar to the diametrical core deformation analysis (DCDA) method (Ito, Funato, and Shono, 2012), but with a number of important improvements.

Jan 7, 2020

By Aki Fujii, Hiroshi Dobashi, Mitsuro Matsuda, Yoshinari Kondo

INTRODUCTION The Metropolitan Expressway Central Circular Route with a total length of approximately 47 km is located outside the Inner Circular Route of Tokyo (at a radius of approximately 8 km from the city center). Sections with a length of approximately26 km, slightly less than 60% of the total length, on the east and north sides are in ser-vice. Completing the Central Circular Route (Figure 1) is expected to enable through traffic concentrated at the city center to get around, and to form a well balanced trans-port network, which will alleviate traffic congestion considerably. The Central Circular Shinjuku Route, a section with a length of approximately 11 km on the west side, is now being constructed at a fast pace. The route is being built mainly by the shield tunneling method to carry out work smoothly under a trunk highway carrying heavy traffic and to reduce adverse effects of tunneling work on residents in the neighborhood. Shield tunnels have recently been becoming longer and deeper, and no secondary linings have been used in an increasing number of cases because of the over-crowding of cities or the reduction of budgets for public works. Economical, durable and high-quality segments have been required for linings of shield tunnels. Segments are made of concrete, steel, cast iron or combination thereof. Concrete segments are generally used in shield tunnels of medium to large diameter. Concrete segments are highly durable and resistant to compression, so they are highly resistant to earth pres-sure, water pressure and jack thrust. They are, however, heavy and have low tensile strength, so they are brittle and their corners are likely to spall. Concrete segments should therefore be handled carefully.[1] The authors have developed a steel fiber reinforced highly flowable concrete segment (referred as SFRC segment) that overcomes the weaknesses of concrete segments[2] to construct economical, durable and high-quality linings. SFRC segments have been applied to outbound sections SJ51 through SJ53 of the Central Circular Shinjuku Route. Unlike conventional concrete segments (referred as conventional RC segments), SFRC segments are made of steel fiber reinforced self-compacting highly flowable concrete. SFRC segments require less reinforcing bars than conventional RC segments because steel fibers are expected to work as reinforcements. Steel fiber reinforced concrete is a composite material that overcomes the brittleness of plain concrete, and has higher resistance to bending, tension and shear than

Jan 1, 2007

By K. Heatwole, D. Shier, A. Davis, J. Kidder, S. Sunkavalli

"Acid rock drainage (ARD) is produced when sulfides are exposed to oxygen and water. Oxidation reactions typically result in a depression of pH and leaching of solutes and metals. Many oxidation models have been developed based on oxygen diffusion, but in environments with high permeability, other transport processes (i.e., convection and advection) can play an important role. Multiple sulfide mineral phases with differing oxidation rates should also be incorporated. WROC, a finite-difference model, was developed to account for these factors in predicting ARD. The program includes sulfide mineral oxidation using a shrinking core mechanism, heat transfer by conduction, heat of reaction and oxygen transport by diffusion and advection. The model was validated using data from the literature. After validation, the WROC model was used to simulate several different waste rock scenarios, including different forms of sulfide mineralization and the effect of implementing a waste rock cover. The results demonstrate that including specific sulfide mineral phases can have a significant effect on oxidation and that implementation of a cover can also aid in reducing waste rock oxidation.IntroductionAcid rock drainage (ARD) is a notable environmental concern in areas where rock or other material with acid generation potential is disturbed. ARD is defined as drainage that occurs as a result of sulfide oxidation in rock exposed to air and water. ARD is characterized by low pH, elevated metals concentration (especially aluminum, iron and manganese), sulfate and high total dissolved solids. The low-pH water that results from acid generation is capable of solubilizing heavy metals contained within the rock. The principal sulfide mineral in mine wastes is pyrite (FeS2). Pyrite oxidation is complex and can involve chemical and biological reactions. Oxidation of pyrite by atmospheric oxygen produces one mole of Fe2+, two moles of SO4 2- and two moles of H+ for every mole of pyrite oxidized, as described by Eq. (1)."

Jan 1, 2015

By W. K. Hitchcock

Anecdotal evidence suggests that re-entering a sealed heating poses a significant hazard, whereby the original heating is rejuvenated at an accelerated rate forcing withdrawal and re-sealing of the area. Bulk-scale laboratory experiments using a two-metre column confirm these mine site observations. A high volatile bituminous coal from New South Wales, Australia was allowed to develop a significant hot spot before being inerted with nitrogen and allowed to cool. Air was then allowed back into the coal after the nitrogen was turned off and a hot spot developed almost immediately at the same location as the original hot spot before it quickly migrated towards the air source within a day. Two more re-entries were simulated. Each successive re-entry developed a broader hot spot and took longer to reach thermal runaway. These results clearly show the behaviour that can be expected when trying to recover a section of an underground coal mine that has been sealed due to a spontaneous combustion event.

Jan 1, 2009

By Eduardo M. Sacris

The performance of the grinding circuit, from the initial stages of operation to the present, is discussed. The mill efficiency as measured by the Bond grindability data and the operating work index is presented. The objective has been to produce a sand cyclone overflow containing not more than 6% +65 mesh. However, this has never been attained even at low milling rates. On the other hand, significant improvements in throughput were achieved by instituting some equipment changes and process modifications within the grinding circuit. The latest approach to solving the coarse grind problem is also discussed.

Jan 1, 1983

By C. L. Kosmoski

In recent years, coal mining safety has attained national attention due to several highly publicized disasters. Despite these threats to worker safety and health, the U.S. relies on the mining of coal to meet its need for electrical power, with 42% of electricity in the U.S. generated through the burning of coal (U.S. Energy Information Administration, 2012b; United Mine Workers of America, n.d.). Furthermore, the production of coal continues to increase and reach record levels every year (National Mining Association, 2012; U.S. Energy Information Administration, 2012a). For this reason, the coal mining industry must continue to find ways to protect its workers while maintaining productivity. One potential approach to protecting workers while maintaining productivity is through improving the safety culture at coal mines. In order to achieve this culture, operators, employees, the inspectorate, etc. must share a fundamental commitment to safety as a value. This type of culture is known in other industries as a ?safety culture,? and can be defined as the characteristics of the work environment (such as the norms, rules, and common understandings) that influence facility personnel?s perceptions of the importance that the organization places on safety. Fundamental to improving safety culture within an organization is understanding the existing safety culture; improvements cannot be made without first elucidating areas that require improvement. This manuscript details the process undertaken by researchers at the National Institute for Occupational Safety and Health (NIOSH) Office of Mine Safety and Health Research (OMSHR) to assess the safety culture at five underground coal mines across the United States. The purpose of this manuscript is to present the aggregated results from those five safety culture assessments conducted at underground coal mines. Additionally, some general recommendations for areas where coal mines might focus their attention as part of their attempts to improve safety culture are offered.

Feb 23, 2014

By Shimi Tzobery, Jay Davenport, Raymond Henn, Sam Bandimere

Over the past several decades, the use of cement-based grouts using ultra fine cement as a replacement for portland cement has begun to gain acceptance as an alternative to chemical solution grouts used in permeation grouting. The amount of information currently available on grouts made with ultrafine cement is limited. The authors used a previously developed field testing program to perform additional tests to evaluate the permeation performance of portland and ultrafine cement-based grouts. For the first time, the 2003 testing program included an attempt to determine the 28 day compressive strength of the sand permeated by the grout.

Jan 1, 2005

By Steve Kral

Invensys is a London-based supplier of automation and control systems to a variety of manufacturing and processing industries. Through its global subsidiaries, Invensys provides customized, advanced process control systems and networks for automating industrial plants, including mineral processing plants. The company employs more than 80,000 people worldwide in its four divisions. They include Automation, Control, Powerware and Software Systems. These four divisions work together to design the complete package for their customer’s automation and process-control needs.

Jan 1, 2002

By T. B. Thompson

The Leadville District has been a prominent metal producer since its discovery in 1860. Veins and replacement bodies both have contributed to district production. The latter have been the major metal sources and are hosted within the Paleozoic Leadville, Dyer, and Manitou Dolomites. Igneous bodies representing eight separate events cut the sedimentary section. The main intrusive complex within the district occurs in the Breece Hill area and was the thermal center about which the vein and replacement ores exhibit mineralogical zoning. Precious metal-pyrite-quartz veins (quartz Th= 422 to 469°C; salinity < 4.2 wt. percent eNaCI) occur within or peripheral to the Breece Hill Intrusive Complex, whereas base metal veins and replacement bodies extend from the complex margins outward as much as 2 mi. Pre-ore and post-ore igneous bodies occur, but Fragmental Porphyry dikes immediately post-date the ore event. The Fragmental Porphyry grades downward from a heterolithic breccia with rock-flour matrix to one with a dark, glassy, sulfide- and phenocryst-bearing matrix, commonly with quartz-feldspar porphyry selvages on the dike. Two types of replacement bodies are recognized in the district: 1) the Leadville-type (LTM), massive sulfide (> 60% sulfides) bodies with recoverable Zn, Pb, Ag, and Au, and 2) the Sherman-type (STM), sulfide bodies (low total sulfide) with barite, galena, sphalerite, argentian tetra.hedrite, and minor pyrite. The latter type occurs only within the Leadville Dolomite and is found throughout the Mosquito Range and extending into the Alma District. The Leadville-type replacement bodies are zoned with a pyritic margin and base metal core. Wallrock alteration and trace Pb-Zn dispersion are strongly developed in igneous wallrocks but are weakly developed in carbonate wallrocks. Cu:Zn, Ag:Zn, and Au:Fe ratios increase outward from the center to the margins of LTM. Some of the sulfide bodies are localized on earlier-formed magnetite skarns. Pyrrhotite, pyrite, and marcasite are the earliest formed sulfide phases while chalcopyrite, marmatite, and galena developed later. Tetrahedrite and electrum occur in vugs and fine veinlets cutting the sulfides. Late-stage barite, dolomite, and fluorite occur as minor phases. Pressure-corrected Th for quartz (375-410°C), sphalerite (374-387°C), barite (320-360°C), and dolomite (310-314°C) fluid inclusions with salinities < 5.2 wt. percent eNaCI characterize the fluid responsible for the formation of the Leadville-type orebodies. These values clearly demonstrate the high temperature and low salinity of the ore fluids. Sulfur isotope analyses for galena and barite from LTM are - 1.9 to + 0.9%o and 7.8%o, respectively. Proximity to feeder veins and favorable dolomite hosts are the principal controls on ore localization. The Sherman-type bodies are not internally zoned but commonly have host rock silicification near the orebody margin or in the footwall rocks adjacent to fluid flowpaths along faults. Early quartz, pyrite, dolomite, and white barite precede base metal-silver minerals which are followed by late quartz and golden barite. It is not clear whether the early quartz and the late quartz and barite are part of the STM-forming process. Fluid inclusion analyses yield trapping temperatures as follows: early quartz, 316-341 °C; barite, 264-347°C; low-iron sphalerite, 215-265°C; and late quartz, 260-278°C. All inclusion fluids have salinities < 8.1 wt. percent eNaCI. Sulfur isotope values for barite and galena from STM range from 13.2 to 24.00/00 (avg: 18.4%o) and -6.8 to -3.8%o (avg: -5.5o/00), respectively. A hydrothermal fluid d34SSS of about 15%o is needed in order for galena and barite in equilibrium to exhibit the observed sulfur isotope compositions. Equilibrium sulfur isotope fractionation between barite and galena indicates a 300°C temperature of deposition. Two separate hydrothermal events appear to have taken place to form the distinctive Leadville-type orebodies and those of the Sherman-type assemblage. The STM is known to be older than the LTM. The latter is likely mid-Tertiary in age, post-dating emplacement of the Johnson Gulch Porphyry. LTM is clearly related to meteoric leaching of sulfur and lead (and other metals) from the upper portions of the Breece Hill Stock. Fluids were transmitted along faults, bedding planes, and contacts, and cooled away from the intrusive complex. Early ore fluids were weakly acidic and developed argillic assemblages in the igneous rocks adjacent to the fluid conduits. Reaction/replacement of carbonate rocks occurred where fluids encountered dolomite, but rapid neutralization prevented any wide-spread alteration beyond the ore-carbonate host contact. Pressures based on sphalerite geobarometry and stratigraphic reconstruction were 1.0-1.2 Kb. The high temperatures of vein and replacement ore fluids indicate that chloride complexing was more effective in metal transport than bisulfide complexes. Cooling, dilution of ore fluids, and reaction with carbonate rocks were the major factors in LTM ore deposition. STM formed over wide expanses of the Leadville Dolomite terrain adjacent to (and possibly capping) the Sawatch uplift. Sedimentary sulfur was derived from Pennsylvanian evaporite-bearing sequences adjacent to the uplift. Ore leads are strongly radiogenic (J-type) and are compatible with a crustal-leaching model. Temperatures of ore formation are higher, and ore-fluid salinities are lower than Mississippi Valley-type ore fluids. Superimposed upon dark-gray, diagenetic Leadville Dolomite are several stages of hydrothermal dolomite regionally distributed astride intrusive centers of the Colorado Mineral Belt. The presence of these later dolomites argues for dolomitization and later ore deposition in response to an abnormal thermal gradient caused by emplacement of Laramide batholiths and their generation of convective flow of meteoric fluids.

Jan 1, 2013