Search Documents

By Donald S. Skufca

This chapter focuses attention on major factors pertaining to plant design and general arrangement of equipment. Considered are efficiency of operations, coordination of maintenance and repairs, plant testing of reagents and possible future plant expansions. The design and general arrangement of equipment considers accessibility for maintenance and isolation for repairs, minimum personnel for operations and cleanup, safe working conditions with minimum interruptions to operations. The constant introduction of new reagents requires eventual plant testing and the manner of isolating a “line” or part of the facilities to allow comparisons in the testing of new reagents is discussed. As technology improves and process changes occur, additional equipment or plant expansions are inevitable. Space for these eventualities must be considered while the general arrangement drawings are in the development stages.

Jan 1, 1986

By G. A. Kordosky

The literature contains several references to the influence of copper solvent extraction reagents on crud formation, but, there is disagreement as to whether the reagent has an influence on crud generation. The results of three pilot plant campaigns, where crud generation was studied as a function of the copper solvent extraction reagent, are reported. These pilot plants were run at operating copper solvent extraction plants using the aqueous solutions being treated by the commercial copper solvent extraction plants. Two of the pilot plant studies showed that the copper solvent extraction reagent had a significant influence on the extent of crud formation while the other pilot plant study indicated the copper solvent extraction reagent had a lesser influence on crud generation.

Jan 1, 1996

By R. G. Graber

Field testing of GPS mining applications has confirmed the technical and operational viability of GPS for precise, centimeter-level positioning in harsh taconite environments. GPS hardware has provided consistent availability exceeding 90%, with precision in certain applications of ± 0.07 foot at 95% confidence levels. Despite these technical successes though, challenges persist in achieving effective GPS integration. These challenges include the acceptance of new job tasks by mine personnel, the capacity of typical mine data communications infrastructure and the need to design GPS interfaces for new mining equipment.

Jan 1, 1998

By J. Mersch Ward

Homestake Mining Company has identified a significant native sulfur resource at its Cinnabar Canyon prospect in Mono County, California. Elemental sulfur occurs as replacements, fracture coatings and breccia fillings in a thick sequence of Miocene-Pliocene intermediate volcanic rocks. The deposit extends along a northwest trending regional fault and measures approximately 900' in width, at least 1800' in length, and has a thickness in excess of 200'. The deposit lies approximately 150' below the surface and is covered by a silicified cap of volcaniclastic strata. The deposit has been delineated by rotary and core drilling. Utilizing a grade cutoff of 5% elemental sulfur, the delineated deposit has a probablelpossible resource of 16.1 million tons of ore averaging 17.9% elemental sulfur containing 2.57 million long tons sulfur. Assay grades within the resource area range up to 40% sulfur over a 40-foot intercept.

Jan 1, 1992

By A. Iordanidis

Fly ash samples were collected from two large lignite-fired power plants of Ptolemais region, northern Greece. Environmental Scanning Electron Microscopy (ESEM) was applied for the characterisation of the samples. ESEM coupled with Energy Dispersive System (EDS) provided fast and accurate results on the morphology, mineralogy and chemical composition of the fly ash particles. Fly ash consists mainly of aluminosilicate glass, silicates, oxides-hydroxides, sulphates, carbonates and char. Various types of chars, spheres (e.g. ferrospheres, cenosphers, plerospheres etc.), spheroids, agglomerates and mineral crystalls were observed. The size distribution of the fly ash particles was correlated with their mineralogical and chemical composition. Possible environmental impacts and potential utilization is also discussed in this study.

Jan 1, 2005

By Lyle W. Talbotr

The DeLamar Silver Mine is a Joint Venture between Earth Resources Company, the Canadian Superior Mining Company and the Superior Oil Company. The property is a consolidation of several old operations in the district. The more widely known are the DeLamar and Sommercamp Mines. The location is 20 miles northeast of Jordan Valley, Oregon and 55 miles southwest of Boise, Idaho. The mine is on the south slope of DeLamar Mountain in the Owyhee Mountains of southwest Idaho Initial interest started in 1969 with serious exploration beginning in 1970. The feasibility study was completed in 1974, and in 1975 Mountain States Engineers were retained to design and build the plant. Processing of ore began in March of 1977 with the first bullion poured in April of that year. The plant is currently processing some 2200 TPD of ore with a grade of four ounces of silver and 0.03 oz. of gold per ton of ore. Cyanide consumption is 2.5 lb/ton, zinc consumption of 0.3 lb/ton and flocculent consumption of 0.5 lb/ton. A flowsheet is shown as Figure I. The grinding circuit is of two stage design. The primary mill is an 18 ft. dia. by 9 ft. long semi-autogenous unit. The secondary mill is a 9 1/2 ft. dia. by 15 ft. long overflow ball mill. The mill discharges are combined and sent to 15 in. cyclones for classification. Cyclone overflow reports to leaching with the underflows reporting to the ball mill. The cyclone feed pump is an 8X6 metal case pump. The primary mill has 1000 installed horsepower and rotates at 68% of critical speed. The ball mill has 700 installed horsepower and rotates at 72% of critical speed. Because the primary mill is horsepower limited the ball charge is varied to maintain the desired throughput. The mill power is held at 980-990 HP by modifying the feed rate. Four inch forged steel balls are added any time the ore feed fails to reach 100 tons per hour for four hours. During periods of extremely hard ore, the ball charge has been as high as 14 v/o and at other times the mill has operated fully autogenous for weeks.

Jan 1, 1980

By Fred N. Kissell

INTRODUCTION During the last few years, several new ventilation developments have attracted the interest of mining engi¬neers. Some of these developments are applicable pri¬marily to hard-rock mining, while others are more applicable to coal mining. STOPPINGS Parachute Stopping The parachute stopping is a new type of quick-erect stopping that is intended for temporary use in hard-rock mines (Kissell, Thimons, and Vinson, 1975). As shown in Fig. 1, the stopping is shaped very much like an ordinary parachute, with a canopy of impermeable fabric that is sewn to regularly spaced straps running to a common point. To erect the stopping, the straps are attached to a fixed anchor point such as a roof bolt, and the edge of the canopy is lifted into the moving air¬stream. The airstream pops the parachute canopy into place, and the differential air pressure across the stop¬ping holds it in place, forcing the fabric against the walls, roof, and floor of the mine opening. The principal advantage of the parachute stopping is that it requires only a few minutes to install, making it a great time-saver for emergency use or for day-to¬day changes in ventilation during the production cycle. However, the parachute stopping does require some minimum air velocity to lift it and some minimum differential pressure to hold it in place. For a fabric weighing 0.27 kg/ m2 (8.0 oz per sq yd), the minimum air velocity is about 0.5 m/s (100 fpm), and the mini¬mum differential pressure is about 0.05 kPa [0.2 in. water gage (WG) ]. There is always some air leakage around the stop¬ping, mainly depending upon the extent to which pipes or other obstructions encumber the airway and prevent good sealing. Leakage of a few cubic meters per second (a few thousand cubic feet per minute) can be expected, unless foam is used to improve the seal at the edges of the canopy. Quick-Fix Blowout Stopping The quick-fix blowout stopping is a variation of the parachute stopping (Thimons and Kissell, 1976), and it is used in the proximity of blasting operations. This type of stopping is designed to be blown out easily by the blast forces, and it may be reinstalled quickly and easily. The long high-strength straps of the parachute stopping are replaced by groups of short straps that tear easily. These straps are attached at six equally spaced locations around the perimeter of the canopy. To erect the stopping, one strap of each of the six groups is fastened to the mine wall, roof, and floor by using spads, by setting pins with a powder-actuated gun, or by tying the straps to some firm anchor point. Once the straps have been attached, the differential air pressure across the stopping, which must be at least 0.025 kPa (0.1 in. WG), forces the stopping perimeter against the mine walls, thus creating the air seal. It is the self-sealing feature of this stopping that makes it a significant time-saver. Only a few attachment points are needed; in many cases, four attachment points are sufficient, since the stopping naturally tends to form a seal with the airway surfaces. When nearby produc¬tion blasting exerts excessive forces on the stopping, one or more of the straps tears away from its attachment point, protecting the stronger canopy from damage. Damage-Resistant Brattice The damage-resistant brattice is a stopping that is designed for use in mines such as salt and limestone mines where the differential pressures are low and the roof is relatively flat. As shown in Fig. 2, the damage-resistant brattice consists of a series of brattice panels that are hung vertically and joined by Velcro® connections. When the brattice is subjected to strong blast forces, the Velcro® connection peels apart and allows the panels to open without incurring damage. The Velcro® connections can be resealed by hand within a matter of minutes. Such damage-resistant brattices have withstood the blast effects of 318 kg (700 lb) of ammonium nitrate-fuel oil (ANFO) explosive detonated as close as 91 m (300 ft) from the brattice. Ordinary brattice cloth is used for the panels, with a 51-mm (2-in.) wide strip of Velcro® hooks sewn along one edge of the length, and a 51-mm (2-in.) wide strip of Velcro® pile sewn along the other edge. Both the hooks and the pile are sewn onto the same side of the brattice cloth. The resulting Velcro® seal formed be¬tween adjacent panels is perpendicular to the brattice itself, and the leading edge of the seal can be directed either toward or away from the blast forces; the brattice works equally well in either case. To hang the brattice, panels of brattice cloth about 0.9 m (3 ft) longer than the height of the airway are cut from a 1.8-m (6-ft) wide roll. The additional 0.9 m (3 ft) of brattice cloth allows 0.3 m (1 ft) for attachment to the roof by means of a board, with 0.6 m (2 ft) for forming a good air seal at the floor. Each brattice panel is wrapped once or twice around a 51 X 102 mm (2 X 4 in.) or 25 X 76 mm (1 X 3 in.) mounting board that is 254 to 305 mm (10 to 12 in.) shorter than the width of the panel. For convenience in

Jan 1, 1982

By S. K. Sharma

The Bureau of Mines' rapid method of dewatering fine-particulate slurries uses extremely high molecular weight polymers. These polymers form large, strong flocs which can be dewatered by sieving or sedimentation. However, sometimes these flocs deteriorate rapidly if water is not removed immediately. During field tests, clay slurries have been encountered that could have been dewatered economically if it were not for the rapid floc deterioration. A kinetics study was conducted to determine the rate of kaolin-PED floc degradation in which polymer addition, to bring the flocs back to their original condition, was used to determine the extent of floc decay. Results showed that the amount of polymer added, to replace polymer lost by spreading, was less for the lower PEO concentrations. For this clay-polymer system, floc breakage as judged by polymer additions followed first order kinetics. It was also found that the addition of fluoride ion stabilized the kaolin flocs.

Jan 1, 1992

By H. Suharyono

The results of an experimental study of polymer-induced flocculation of clay suspensions in continuous, stirred-tank reactors are presented. The effects of polymer dosage, mixing time and mixing intensity are shown to be generally similar to those observed for equivalent batch systems, but flocculation appears to be generally less effective in the continuous process. Settling rates are lower and supernatant turbidities are higher for the continuous system. It is postulated that non-equilibrium effects due to simultaneous polymer adsorption and floc growth can be exploited so as to enhance flocculation in batch systems. The nature of the continuous process, however, offers less opportunity for taking advantage of such effects. Conditions in a continuous flocculation system inherently lead to a closer approach to equilibrium.

Jan 1, 1994

By K. J. Sollman

As a class, silicate minerals have likely found the broadest, if not largest volume, use in combination with polymeric binders of all industrial minerals. Among the silicates, calcium metasilicate, wollastonite, enjoys a front runner position in a near universal sense. It is a viable and desirable part of composites ranging from thin films to large moldings; from a common filler/extender for paint for your garage to a reinforcement for the exterior surfaces of a luxury vehicle affordable to very few. This article is focused upon the variations in particle morphology and the surface characteristics which, by way of commercial examples and discussion of active research programs, make this environmentally benign mineral so unique.

Jan 1, 1993

By M. Amick, G. Swan, R. Hill, C. Pritchard

Falconbridge is a major basemetal producer in the Sudbury Basin of Ontario, Canada. The company identified a need to find a safe and cost-effective replacement for the welded wire mesh used to support loose ground during underground nickel mining. Falconbridge took a methodical approach to the concept of a spray-on liner as a screen replacement, proving the strength characteristics of the liner as a safe, cost effective and suitable method of supporting ground Compact, hydraulic mixing and spraying equipment were developed and are now in use at the Fraser Mine. Tekflex has been approved as a wire mesh replacement and has been in use since November 1998.

Jan 1, 2002

By J. R. Sturgul

A dynamic input-output model for a coal power enterprise that now includes four underground coal mines, three coal washing plants, a power plant and a railway transportation system was developed. The model is applied to analyze investment alternatives for long-term development, including the expansion of existing mines, the opening of new mines, the construction of new coal washing and power plants and the upgrading of the railway system. As a result, the optimal investment strategy with capital schedules and projected sector outputs is obtained. Also, the importance of the new power plant to the strategic development of the company is demonstrated. It is concluded that, without applying a dynamic input-output model, it would be much more difficult or impossible to conduct such a systematic and compete analysis.

Jan 1, 1999

By M. Noaparast, F. Woodcock, A. R. Laplante

A novel methodology for estimating gold recoveries in gravity-separation circuits is presented. The methodology makes use of a population-balance model. The model represents gold liberation, breakage and classification behavior and applies preconcentration and recovery performance curves to gravity-recoverable gold. The derivation of the necessary parameters is explained and demonstrated using data from an actual gravity circuit and from a projected application. The methodology makes it possible to estimate the performance of a gravity circuit having a large gold circulating load and a relatively-low unit recovery (e.g., a jig) or having a high recovery on a bleed of the circulating load (e.g., a Knelson Concentrator).

Jan 1, 1996

By P. Holman

I would like to start this paper by looking back about twenty years to see where we have been in the mining industry. We will also look forward a bit and talk about what lies ahead. Here is what has happened to the world economy since the 1970s. Economic growth was strong in the early 70s, but slipped into a recession in the middle of the decade. Then, after a fairly decent recovery recession struck again in the early 80s and since then growth has been rather sporadic. All in all, it has been a real roller coaster ride. There will continue to be plenty of ups and downs in the world economy in the future.

Jan 1, 1993

By Y. Q. Lu

Efficient flotation of fine phosphate minerals from a deslimed waste phosphate stream (-74 microns) has been achieved by both bench-scale flotation and by flotation with a 2-inch air-sparged hydrocyclone (ASH) unit. A sample was collected from the waste phosphate slime stream at the SF Phosphate Limited Operations near Vernal, Utah, for flotation experiments at University of Utah laboratories. The collector used was a mixture of fatty acid, petroleum sulfonate and kerosene. Bench-scale flotation test results show that the minus 15-micron particles have a significant adverse effect on phosphate flotation. When the minus 15-micron material was removed by a classifying hydrocyclone, improved flotation recovery and concentrate grade were realized. A bench-scale flotation recovery of 86 % with a concentrate grade of 16% P2O5 was obtained from classified waste slime (74 x 15 microns) feed material containing 11.3% P2O5 In contrast, a 90% P2O5 recovery was achieved with a concentrate grade of 16-18% P2O5 by single-stage ASH flotation. With a second stage of ASH flotation, a concentrate containing 23% P2O5 was realized at an overall recovery of 75%. These results indicate that the industrial application of ASH flotation technology for phosphate recovery from waste slimes is promising.

Jan 1, 1995

By J. G. Groppo, D. J. Sung, B. K. Parekh

Hyperbaric filtration for the dewatering of fine coal cleaned by froth flotation was evaluated on a laboratory scale. A laboratory pressure filtration procedure designed to obtain a uniform cake structure from dilute slurries containing a significant amount of coarse material is described. Baseline tests were conducted to determine the optimum operating conditions for the eventual application of the process to a continuous pilot-scale hyperbaric filter. Investigated were filter operating parameters such as driving force, time, cake thickness, percent solids, viscosity and pH.

Jan 1, 1996

By Estban M. Domic

The modem copper industry presents an excellent opportunity for the application of clean, environmentally friendly techniques using currently available hydrometallurgical technologies. This paper briefly reviews key events in the development of modern hydrometallurgy in Chile. Discussion is given to those prominent events whose impact continues to be felt on most projects currently underway. Mention is also made of the foundations of heap leaching technologies, preceded by agglomeration and acid curing, known as the T.L. Leaching Process, the cornerstone of more recent developments. A review is also presented of the leading copper hydrometallurgy projects of the 1990s. A list of those projects, their tonnages and the estimated date of implementation is provided. The conclusion provides an overview of developments in research and the trends in the implementation of copper hydrometallurgy projects in Chile for the coming years.

Jan 1, 1998

By S. Dessureault

Integrated information technology infrastructure is the linking of data across various applications throughout a business to gain further data-driven improvement opportunities. Decision support systems (DSS) are the various improvement opportunities that facilitate decision making for a potential optimal outcome. Integrating tera-bytes of data spread throughout a business is complex. There are tools to facilitate the development of such data-driven DSS. This paper analyzes the various tools that may facilitate the development of complex data-driven decision support systems, namely; information models, business models, data utilization model, and testing environments. A case study is presented to demonstrate how these tools facilitated the development of an automated activity-based budgeting DSS at a large-scale underground mining complex.

Jan 1, 2004

By Tim Q. Haldane

The ability to efficiently process low grade gold ores has allowed the Gold Fields Mesquite Mine in Imperial County, California to expand from a 2.1 million tonne per year rate in 1986 to its present 7.3 million tonne per year processing rate. Increased tonnage demands led to the 1989 construction and start-up of a dump leach pad to supplement the existing heap leach operation, resulting in an excellent opportunity to compare the two processes at the same operation. Additional operating costs associated with the crushed ore heaps are justified through enhanced recoveries, even at very low ore grades. An overview of current operating practices at Mesquite is presented along with metallurgical and economic comparisons between the crushed and run-of-mine ore heaps.

Jan 1, 1990

By T. J. van der Walt

This paper proposes a new methodology to model ill- defined processing operations using neural nets (NN's). A process with many variables (large dimensionality) cannot be modelled adequately if limited process data are available. This problem of multi-dimensionality is addressed and an approach suggested to reduce the dimensionality using NN's. The result of this modelling methodology is a combined model of phenomenological expressions and NN's. The model can successfully be incorporated in a dynamic simulator of the process. A new approach to conduct modelling on the basis of continuous data collected directly from an industrial processing unit, is also proposed. The modelling methodology is applied to a typical processing operation, the resin-in-pulp (RIP) process.

Jan 1, 1992