Search Documents

Adequate ventilation of coal mine working faces is the single most important technique for controlling respirable dust and methane. Choosing the right technique presents some tough questions. Bureau research has shown that to control respirable dust you must contain the dust near the face, keeping rollback (turbulence) to a minimum. For methane the most effective approach has been to use a blowing brattice or tubing and to create turbulence and disperse the face methane, allowing it to pass over the machine and into the return. It is immediately apparent that the two approaches may counteract one another, thus complicating the decision as to which system may be best for a given situation. At present, Bureau research has developed two successful machine-mounted face ventilation systems to meet these different needs and allow deeper cutting. The fan-powered dust scrubber is designed to control dust primarily associated with blowing face ventilation systems. The spray fan controls methane on exhaust-ventilated sections.

Jan 1, 1988

By Keith G. Wallace, Daniel J. Brunner

The traditional approach to mine ventilation planning involved making estimates of airflows, including leakage routes, and summing the corresponding pressure drops along consecutive paths in order to determine the fan pressures required. This methodology changed completely with the availability of computers. Mainframe digital computers began to be used for mine ventilation network analysis in the mid-1960's. Their use spread rapidly throughout the world in the 1970's. Mainframe machines were employed owing to the need for high speed numerical procedures and substantial storage requirements. However, during the past decade, the growing availability of low cost but powerful microcomputers has allowed the development of net- work analysis programs that can handle ventilation systems of hundreds of branches, and which can produce results within a few minutes. This paper discusses recent advances in software and hardware development specific to mine ventilation planning. Software developments include interactive data and output manipulation, graphical representation of output, internal checks on input parameters to preset ranges and subroutines which calculate the gas distribution throughout the network from known gas sources. Hardware advances have led to significant increases in memory to facilitate the analysis of large ventilation models, math co-processor chips which greatly shorten run times, and plotter hardware for graphical output displays. Recent software developments make it possible to graphically display output on printers faster than on standard plotters.

Jan 1, 1989

By Huaiyu Liu, Shan Liu, Dashang Chang, Maixi Lu, Yaqun He, Yali Kuang

The expert system for coal preparation plant design mainly solves the crux--separation flowsheet design and optimization of product structure. There are twelve basic flowsheets available in the system which are representative of financial plants. The system can select better flowsheets automatically according to the property of feed and scale of plant. Then, it can choose the best flowsheet and product model from the better flowsheets through analysis and optimum calculation. The expert system is made up in Turbo Pascal 6.0 and consists of three sub-systems: Lump and grain coal system, coal slimes processing system, and raw coal system. Several representation methods, such as production rule, procedure, and object-oriented programming, are used to express the expert's knowledge in the system. To decide the optimum product structure, Zangwill's method is used to make an advance product model. The expert system has the performance of interpretation strategy, by 'tracer" technology and pre-arrangement text, and of learning new expert's knowledge.

Jan 1, 1996

Diesel engines are used in underground mining 1 throughout the world. Exhaust gases from those engines contain toxic components. To protect quality in underground mines, diesel emission control was introduced decades ago, many years before the first surface applications. Today, emission controls, such as catalytic converters, are standard on underground diesel engines in countries concerned with occupational safety and health. Nett Technologies manufactures a range of diesel emission-control devices for underground mining. Emission problems are not the same at each mining operation. And there is no universal control technology. The selection of exhaust aftertreatment technology depends on raw exhaust emissions, particular emission problems, fuel quality and economics. Some of the technologies that have been used in underground mining to control diesel emissions include catalytic converters, diesel filters, fume diluters and water scrubbers. Table 1 compares the effectiveness of these technologies to control the particular components or aspects of diesel emissions.

Jan 1, 1997

By R. M. Cox

Pneumatic coal loading and conveying systems provide alternative methods for the safe and efficient mining of the thin, high-grade coal seams found in the Southern Appalachians. Pneumatic systems eliminate most of the health and safety hazards associated with the operation of conventional mining and haulage equipment in small low-coal mines by removing powered mobile equipment from the mine. Ventilation is also improved by the coincidental removal of gas and respirable dust from the mine by the operation of the pneumatic loading and conveying system. Other significant advantages of pneumatic coal recovery systems are relative simplicity, operating flexibility, low capital cost, quiet operations, environmental benefits and ease of automation. The design considerations and field evaluations of experimental prototype pneumatic coal loading and conveying systems installed and operated in small thin-seam mines are presented in this paper. In addition, fundamental design criteria and recommendations for the installation and operation of a variety of pneumatic coal loading and conveying systems that offer alternative coal-recovery systems that alleviate the serious health and safety concerns of current small mine operations are proposed.

Jan 1, 2000

By S. D. Thompson, G. T. Lineberry, A. J. Basu

Conveyor belt haulage has become the preferred mainline transport method in underground coal mining, especially for multi-unit mines. Proper designs for belts (width and speed) and surge bins (placement, capacity, and discharge rate) are necessary to achieve efficient mine haul- age. Two computer simulation models, CMBCS and BELTSIM, available for designing these parameters were compared. These comparisons included modeling, input data requirements, statistical flexibility, accuracy of simulated loading, and execution time.

Jan 1, 1991

By J. Alton Burks, Robert R. Stein

This paper focuses on the noise exposure levels of miners employed on longwall production faces. Along with the increased production from longwall units has come the potential for greater noise exposures. Typical noise levels are given for the various noise sources that are present on modern longwall faces. Exposure times have typically increased since the introduction of longwall technology in this country. Representative exposure times and patterns are analyzed. Possible solutions are presented for generalized cases. Engineering controls developed by the Bureau of Mines are explained and their potential effectiveness is calculated for the cases presented. The role of hearing protectors in an overall hearing conservation program is also investigated. Recent research performed by the Bureau suggests that the actual performance level of muff -type protectors may be less than the manufacturers ratings under certain circumstances. The use of muff- type protectors is discussed and analyzed with respect to their use on longwall operations.

Jan 1, 1992

By A. D. Wunderlich

Providing a safe & secure environment for your employees and other company assets is absolutely necessary in our litigeous society. Security hardware is no different than computers or other technical equipment, in that new equipment is developed each year that makes older equipment obsolete. This presentation will help to explain how your existing security system and security procedures can be updated to meet industry standards without the expenditure of a great deal of money. If you are concerned about potential security problems and how to address these problems, this presentation is a must.

Jan 1, 1995

On my arrival in New York after the Russian examinations John D. Ryan, president of Anaconda, asked me what my plans were. I told him I wanted to be useful somehow in the World War that we had entered while I was away, but I did not know how. Ryan and Thayer told me that the new American Air Corps was gathering a group of executives, most of them young, to go to France as Army officers to help with the industrial side of our aviation activities. This would include construction of military airports, maintenance, and supply for our rapidly growing Air Corps. They thought I might be accepted in this group of about 30. It seemed to be just what I wanted, and I put in my application at once. My application was accepted about three weeks later and I was told to come to Washington to take physical and other tests and to meet others of the group. I liked them. They were a cross section of competent American manufacturers, bankers, automobile executives, and merchants. I was the only miner. I had many discussions in the days in Washington with members of our organization and others I knew who were going into war service. Attitudes were very different from those 55 years later. There was no discussion as to whether war was right or wrong. We were in it and must do all we could to help. At the same time there was a holdover from the days when, at least for the elite, war was high adventure. Even the most high-minded did not then realize that war is a horrible form of wholesale murder and, in 1917, it would have been treason to suggest this. I had two weeks before our industrial group was to start work which gave me time for a hurried trip to Berkeley where Dorothy and I announced our engagement.

Jan 1, 1976

By Otis M. Clarke

Although most bauxite mined is used to make metallic alu¬minum, more than a million tons of bauxite is used annually in the United States in the manufacture of refractories, chemicals, abrasives, and cement. Raw material requirements are becoming increasingly difficult to meet because high-grade bauxite, required for some uses, is limited. The supply of raw material for high-alumina refractories is most critical because a low-iron bauxite is needed. Although there are substantial bauxite reserves in the world, bauxite suitable for use in refractories is limited to a few districts.

Jan 1, 1977

By K. A. McDonald

This paper will describe the experiences of Hibernia Holdings, Inc. in constructing a mineral processing facility in Mexico. It will attempt to set forth a guideline on what companies attempting to operate in Mexico can expect and what actions they can take. Ownership laws, import/export laws, labor laws, security, transportation and operating experiences will be discussed.

Jan 1, 1994

By H. W. Renner

The paper industry is an $80 billion/year business that is the largest consumer of industrial minerals. Paper industry generally refers to paper and paperboard products, including pulp mills. Grades and uses of paper and paperboard are very diverse, including such things as napkins, paper plates, corrugated boxes, magazines, newsprint, currency, and copier paper. Only about 40% of paper utilizes industrial minerals as fillers or coating materials. Minerals are used for both functional and economic reasons. Most often, minerals such as kaolin clay and calcium carbonate are used to improve print quality, brightness and opacity of paper. The minerals can be added as fillers into the paper in the wet end of the papermaking system, or can be applied as part of a coating to the paper. Coated papers are the highest quality paper, being used for magazines, advertising brochures and annual reports. Common uses for filled uncoated paper are books, copier paper, envelopes and many of the Sunday newspaper advertising inserts.

Jan 1, 1993

By Anthony R. Przybylek, John M. Visnesky

INTRODUCTION Thermal dryers have been utilized for reducing moisture of bituminous coal since the late 1930's. Since that time, numerous changes in the coal industry have motivated advances in thermal drying technology. The purpose of this paper is to discuss the changes that occurred to dryer design and focus on current practices of fine coal drying. The major topics discussed in this paper are: - Early Thermal Dryer Design and Evolution - Current Drying System Design and Associated Components - Current Economics of Fine Coal Thermal Drying - Future Markets and Design Considerations EARLY THERMAL DRYER DESIGN AND EVOLUTION Background The practice of drying fine coal with heated air has been performed for more than one half century. Throughout that period, both Metallurgical and Steam coal producers have used this method for reducing the surf ace moisture content of their fine plant products. During the late 1930's and early 19401s, vibrating bed and flash dryers were used to per- form the drying duties. Closed water circuits and vacuum filtration had not yet been integrated into process circuitry and centrifugal dryers were in their early stages of development. During that same period, changes in mining practices were reshaping the distribution of coal to our processing facilities. Plants originally designed for the purpose of processing coarser fractions of coal were being burdened with additional quantities of fine coal. Those plants, unable to recover fine coal, would reject these solids to plant bleed. The higher incidences of stream pollution that resulted from these events prompted clean stream legislation and the need for new, more efficient fine coal recovery circuits. The coal processing industry responded to these needs by integrating closed water circuits and filtration into circuits. The fine coal filter cakes recovered exhibited poor handling characteristics by themselves and often required further dewatering to improve their characteristics. Flash dryers at that time were being used to dry the coarser products. For those facilities operating flash dryers, the solution to this new problem appeared to be simple. The filter cake was combined with the coarser (-1/4") coal and then introduced to the flash drying column for drying. The filter cakes, however, presented significant problems for the flash drying systems. Heavy lumps of filter cake could not be dispersed and conveyed by the rising hot air and as a result would settle out in the bottom of the column. This material, known as "drop-out", would then accumulate and require further handling. The solution to this problem was not an easy one. Sophisticated mixing equipment was employed to condition the feed to the dryers. As attempts to minimize drop-out with this approach failed, the only recourse was to collect the material with conveying systems and recycle it back to the plant or dispose of it. The additional costs of handling this material reduced the attractiveness of the flash systems and opened the door for the development of a new, more cost effective coal drying system. Due to the nature of the problems experienced by the flash systems, fluid bed systems were considered. Fluid bed dryers were being used in other industries at that time but had no operating history in the coal industry. Dorr-Oliver transferred technology from other industries and built the first fluid bed drying system for fine coal.

Jan 1, 1988

By Syd S. Peng

Introduction Modern longwall mining, introduced to the US coal industry in the mid-1960s, is the latest coal mining technique. Today, longwall mining produces more than 15% of all underground coal production. The growth of longwall mining in the US is slow. However, nearly two decades of longwall mining have demonstrated that its benefits outweigh the disadvantages. Longwall Advantages Production and Economics - A typical longwall production ranges mostly from 0.9 to 1.8 kt (1000 to 2000 st) of clean coal per shift. This is about three to six times the production of comparable continuous mining units. Furthermore, there are much less rejects in longwall mining, typically 15% to 25%. It must be noted, however, that a new longwall with an inexperienced crew may produce less, depending on mining conditions. But as experience gains, production increases rapidly. Due to its high production, the cost per ton of coal mined over the mine's lifetime is cheaper with longwall mining than with continuous mining. A study on a conceptual mine of 25 year life using actual operational data (Dangerfield, 1981) concluded that the cost per ton of coal mined is 32% cheaper by longwall than by continuous mining. Another benefit from its high production potential is that it enables the production to be concentrated in a few longwall faces versus many units of continuous mining required to achieve a similar production. As a result, mine organization and management simplify considerably. Safety and Savings - Most US longwalls use shield supports that cover the roof with solid canopy and isolate a gob completely from the face area. Thus, if the supports are properly selected and operated, the potential for roof fall accident is almost zero. Furthermore, it is not unusual that a well-run longwall face is much more orderly and cleaner that most well-run machine shops. The ventilation system for longwall mining is the most ideal type. It is simple and unique. No auxiliary fans are required. The fresh air sweeps through the whole face. Its volume and velocity can be adjusted as demanded. Recovery - In spite of multiple entries layout for US longwall panels, the longwall method recovers up to 40% more coal than the continuous mining method (Dangerfield, 1981). The typical recovery for longwall mining is 70% to 85% versus 45% to 80% for continuous mining. Versatility - Longwall mining has been employed successfully in seam heights ranging from 0.8 to 3.7 m (2.7 to 12 ft); in seam inclinations from horizontal to 35°; in overburden depths from 46 to 914 m (150 to 3000 ft); in single or multiple seam mining; and in uniform or irregular seam characteristics. For seam height less than 1.2 m (4 ft), the plow is used instead of a shearer. However, in spite of recent developments, the plow still is unsuitable for hard coal seams. Slow Acceptance How come longwall mining, with so many advantages, has not spread more rapidly? Undoubtedly, the major reason is the large capital investment required. Under normal market conditions, the capital required for a longwall panel ranges from $7 to $11 million. Another factor is the uncertainty of its applicability to any specific coal seam of interest where longwall has not been used or operated successfully. Although longwall mining elsewhere has proven its applicability to wide-ranging seam conditions, there have been several failures in the past two decades. Analyses of those cases show that most failures can be attributed to inexperience, both operational and technical, including equipment selection. Therefore, personnel training on the longwall mining technique is absolutely necessary before its initial operation. Some earlier statements about adverse surface subsidence associated with longwall mining were misleading. Research has proven that surface subsidence under longwall mining is controllable and predictable. And, if longwall mining was mandatory since the onset of coal mining in the US, there would be no surface subsidence problems over abandoned mined land today. It is a blessing that surface subsidence occurs

Jan 3, 1985

By P. Kolettas

The development of novel methods for the investigation of the subsoil contributes to the improvement of geotechnical research, enhances the obtained geotechnical characterization and may reduce the investigation cost by reducing the number of required tests. Non-destructive testing methods, performed either in situ (i.e. electrical tomography, seismic refraction, etc) or in the laboratory can provide initial data and perhaps estimates of rock/soil properties. This study focuses on the development of rock material properties and/or characteristics based on non-destructive laboratory testing of a number of stones, ranging from porous (bioclastic) limestones to impervious marbles. Seismic velocity measurements as well as attenuation signals were digitally recorded using a digital oscilloscope. Data were processed using a novel technique of spectral analysis available through special Matlab packages employing Fourier transform methods. More specifically, the NFFT (Non Equispaced Fourier Transform) transformation was applied to seismic waves traveling through the subsoil using the Autosignal program (by Seasolve) and the Specgramdemo program included in the Signal Analysis toolbox of Matlab 6.5 (Mathworks). Results indicate a definite relationship between the frequency content of the signal and the rock type as well as the degree of saturation of the specimen.

Jan 1, 2008

By Duane A. Smith

Horace Tabor. No 19th century Colorado mining man is better known but, unfortunately, probably less understood. He is little appreciated for his significant contributions to the industry and the state. A century ago, Tabor was headline news. The legend today, however, has become so all pervasive and so interwoven with fact that the two are hard to separate. For example, he never told Baby Doe on his death bed to hang on to the Matchless mine. Yet this has emerged as staple Tabor fare. So much attention has been focused on his matrimonial triangle that it overshadows the man. Symbol of mining's reward Tabor traveled west in the 1859 Pike's Peak gold rush. In the next generation, he came to symbolize the rewards mining might lavish on an individual. The Leadville Daily Herald (Sept. 10, 1882) could write, without exaggeration, that "the extent which the mining industry of Colorado is under obligation to Tabor cannot be easily estimated - what he has done for Leadville and Denver is patent to all." It had not come easily, nor had Tabor started out a success. His early placer mining at Payne's Bar, near present-day Idaho Springs, CO, had turned no fortune. So in 1860, he, his wife Augusta, and son went south to Colorado City, then over Ute Pass and up the Arkansas Valley to Oro City. Arriving soon after the initial discovery, Tabor staked a good claim. With a sharp eye, he and Augusta broadened their base by establishing a store. Both mining and business would pay dividends in the following years. By the season's end, though, Oro City was already declining. Always on the lookout for a richer district, Tabor and his family moved the next year across the mountains to promising Buckskin Joe. The familiar pattern followed, with the store and post office being the center of their attention. Mining investment and management now replaced the earlier physical panning and sluice operating. Seven years later, the Tabors abandoned Buckskin Joe and returned to Oro City. It had moved up California Gulch to be near the district's best mine, the Printer Boy. Middle class was not enough Middle class respectability, plus a steady income, was the Tabor's by the 1870s; fine as far as it went. But it proved far from the fortune Horace had always been seeking. Oro City languished in the backwash of Colorado mining and Tabor seemed like many men who had drifted around the Territory following the ebb and flow of mining. His faithful wife Augusta had been a steady factor in the success the family achieved. She helped year after year to operate the store and post office. Not simply the happy-go-lucky individual he has often been portrayed, Tabor was a hard working businessman/mine owner. An R. G. Dun and Company agent evaluated him in 1876 "Net worth $23,200. Is a very shrewd businessman and not liable to lose money, has a good chance to make money as he had no competition." Leadville: Tabor's silverlined-fortune After all those years on the Colorado mining frontier, in 1877, Lake County's wealthiest and most respected merchant made another move. It was short in distance, only 4 km (2.5 miles) down California Gulch, then a little north to a new mining camp. This new camp, soon named Leadville, gave birth to the Tabor fortune and legend. Middle-aged (Horace was 47), the Tabors once more set up their general store and found themselves in the midst of the open¬ing of a new district. This time silver beckoned and not the gold that had brought them West 18 years before.

Jan 1, 1989

Engineering programs usually do not provide sufficient opportunities for students to develop written communication skills. The responsibility for developing those skills is frequently delegated to the humanities faculty, who in a single technical writing course are supposed to transform engineering students into proficient communicators. A general template which was developed for report writing in our senior level capstone design courses is discussed. Students have improved their writing skills by using the template. The writing assignments have provided the students the opportunity to write and revise more technical reports that communicate their design.

Jan 1, 1995

By G. M. Rao

It has been a universal observation that rich grades of ores and minerals are getting depleted, simultaneously the demands for civilization are ever increasing coupled with occurrence of poor grades of ores and minerals posing a problem to the processing engineers. At the same time, the cost of mining and milling are increasing, creating a situation where the management has to handle and process low grade ores at an economic level keeping environmental stipulations and control to be safeguarded which has been an additional cost for the management to comply with.

Jan 1, 1994

By M. B. Díaz Aguado

Traditionally, the practical evaluation of a mining project for a potential investment has been made considering mainly technical aspects. But the concept of sustainable development has introduced significant changes in the factors analyzed to make the final decision. This paper proposes an empirical evaluation of a project considering not only technical, economic and financial parameters, but also associated risks and other intangible aspects, such as political considerations, stability in the legal frame, social factors and environmental issues. The proposed methodology is practical and easy to apply for project management. Among its main advantages, the following could be quoted: using this evaluation two different projects or locations of a same project can be compared, future behaviors could be predicted, the index incorporates a new approach to specific mining projects and this perspective could also be applied to other projects with environmental and social impact, such as civil works or industrial projects.

Jan 1, 2007

By Floyd C. Bossard

A method of hand-calculating the air-cooling requirements of a conceptualized underground mining operation is presented for the reader's orientation. Separate air heat load calculations were conducted for adiabatic compression, electromechanical equipment, wallrock, broken rock, groundwater, and blasting operations. The air heat sources were calculated for four mining levels under conditions representative of a typical planned mining operation at depth. The total heat gain on each level will approximate the level air-cooling requirements. The results of these hand calculations can be further modified by the use of mine ventilation computer software that refine the heat-source calculations, predict underground ambient air temperatures, and establish the air-cooling requirements of a mine. INTRODUCTION The principal mining method employed is a modified vertical crater retreat (VCR) blasthole operation. Typical scopes range from 20 to 40 feet wide, 75 to 100 feet long, and 100 feet in height. Six and one-half inch blastholes are drilled with an "in the hole" hammer drill. Eight-foot high horizontal rounds are blasted down. Mucking of ore from the undercut to orepass is done with LHD equipment operated from a remote control station. Backfill includes hydraulically placed tailings with cement, and waste rock when available. Stope access is from ramp sub-levels on 50-foot vertical intervals. Crosscuts are ramped down to the first stope cut 25 feet below the sub-level elevation. Then the crosscuts are raised by taking down the back when each stope cut is completed, until an elevation 25 feet above the sub-level is reached. The crosscuts are filled with tailings, and/or waste rock. See Figure 1. Typically, a two-pronged approach to defining the air-cooling requirements is conducted. First, the principal sources that make up the air heat load are individually hand-calculated. Second, projections of mine heat load are calculated by utilizing computer modeling techniques. This paper discusses the first method (hand calculations) of determining the individual components of heat flow into the mine. CALCULATED AIR HEAT LOADS Adiabatic Compression The plans for the mine include delivery of 300,000 cfm of air to ventilate the lower level operation. This is equivalent to approximately 200 cfm/ton of rock produced (300,000 cfm/1500 tpd of ore and waste). As air flows down a shaft, with no heat interchange between the shaft and air and no evaporation of moisture taking place, the air is heated in the same way as if it were compressed in a compressor. Dry air increases in temperature about 5.4°F per 1000 feet. One BTU is added to each pound of air for every 778 feet of decrease in elevation, or is subtracted for the same elevation increase. For dry air, the dry-bulb temperature change is 1/(0.24 x 778) = 0.00535°F/ft., or 1°F/187 ft. elevation. Auto-compression may be masked by the presence of other heating or cooling sources, such as shaft wallrock, groundwater, air and water lines, electrical facilities, etc. The major factors influencing the temperature of the air delivered underground by a shaft are (1) the night time cool air temperature's effect on the rock or lining of the shaft, (2) temperature gradient of ground rock related to depth, and (3) evaporation of moisture within the shaft which increases the latent temperature and decreases the sensible temperature. [Calculation For Adiabatic Heat of Compression] a. Assumptions: 1. Three hundred thousand cfm of fresh air at 3000 level has increased in temperature during the summertime to the point where it has little available cooling power. Air-cooling will be required on 3000 Level and below. 2. Elevation of 3000 Level is approximately +1000 ft. above sea level.

Jan 1, 1993