Search Documents

By A. C. Kunkie, C. J. Marshall

Highly delaminated muscovite mica products (WG-1 and WG-2) have been developed by J.M. Huber Corp. The micas are characterized as a 325-mesh product having high brightness and very narrow particle size distribution. At 40% loading in polypropylene, WG-1 mica provides substantial improvement in tensile modulus and equal tensile strength to unfilled polymer; in high-density poly- ethylene (HDPE), WG-1 provides four times the tensile modulus and a 50% increase in tensile strength over unfilled polymer. Surface modification of the water-ground mica (SM ™) provides substantial improvement in tensile strength over untreated mica at greater than 20% loading in polypropylene; in HDPE, tensile strength is twice that of unfilled polymer.

Jan 1, 1988

By E. Finch

Beneficiation tests were conducted on samples from three ore zones in the Los Monos, Navay orebody in Táchira State, Venezuela as part of an overall feasibility study. The scope of work included ore sample characterization, flowsheet development, and optimization of beneficiation variables on a bench scale followed by confirmation on a pilot plant scale. Phosphate in the ore samples occurred primarily as francolite and was associated with quartz, kaolinite, and feldspar. Liberation of the phosphate began at 589 microns (28 mesh) for the main ore zone sample and at 295 microns (48 mesh) for the lower-grade ore zone samples. Development tests on simulated mining composites demonstrated that the samples responded well to 589 micron (28 mesh) grinding, two stages of high intensity scrubbing, conditioning at high % solids with caustic and equal amounts of tall oil and fuel oil, and separate coarse and fine flotation circuits with one stage of roughing and two stages of cleaning (reflotation). Concentrates in the range of 31.5-34% P205 with recoveries from 64-70% were obtained from the mining composites. Product quality for all concentrates in the range of 31.5 % P205 was good; 1.40 CaO/P205 and 0.04-0.05 minor element ratios. Confirmation testing in a continuous pilot plant produced results similar to those achieved in the laboratory.

Jan 1, 1993

By Thomas Oberndorfer

INTRODUCTION Since several years the author is engaged in research activities in the field of mining method modelling (Oberndorfer, 1993 and 1994). The initial goal was to improve and assist the selection of the most appropriate mining method. However during investigations it became obvious that the most beneficial application of computer support is the fast calculation of numerical assessment rather than the consideration of all, i.e. also qualitative, criterions necessary for final decision. Numerical results serve - together with qualitative considerations based on the experience of the mining engineer - as a basis for decision. The emphasis is on "fast" calculation, as only this property makes it possible to calculate and compare many distinct variations. As long as no procedure exists, which optimizes all involved parameters, calculating many variations is of great important, because it is the only way to increase the chance to pick a alternative "close to optimum", but also to learn about the sensitivity the result will react on changes of input parameters, which are rarely known exactly. Generally speaking many trials give a better basis for final decision. It is no secrete that the most important obstacle towards quick calculations of a series of alternatives is not the processing time of the computer, but the time required for setting the input data in way that the computer can start processing, which is usually inter- active man work on the screen. Furthermore usually several distinct programs are required to cover the whole range of involved problems, with corresponding problems in automatic data transfer. The research work's goal was to overcome these problems. The approach developed was to describe a mining method more in a theoretical way (i.e. to give the computer some degree of "consciousness" on mining methods), which then can be applied under any specific conditions. E.g. a cut-and-fill operation will be "generally" the same in narrow or thick deposit areas, but the resulting keyfigures, e.g. total tonnage, productivity, dilution and loss, or finally costs per ton, will differ significantly. The approach (MMM = mining method modelling) presented reflects a deduction from the general case to a specific one (rather than the other way round). The developed model is general enough to be applicable to any mining method, and also to any degree of precision the mining method should be described, contrary to programs designed for specific mining method layouts which can be adjusted in a more or less wide range. PROGRAM DEVELOPMENT The principle correctness and feasibility of the approach was proved by a prototype program. However this program was more on a research level and far away from application for "real world" problems. The reason for this was, that it was regarded wasted time to re-invent certain tools, e.g. geometry intersection, deposit modelling or visualization. Hence it was tried to attract several software producers to invest in finalizing the model. Unfortunately this endeavor was not successful. Despite this defeat - and after some months of resignation - a final start on the project was decided. he reason for this decision was not at last the research activity in respect of low-cost underground mining methods for bulk- material as a substitute of typical quarry operations due to environmental restriction. This research work - which is in particular important for Austrian mining activities in beautiful and touristically used landscape - requires a lot of calculations in the way described. Both are still in state of progress, but - regarding mining method modelling - preliminary results can be presented. A complete re-programming of the program was required. Most obvious are the changes of programming language and operating system environment. Instead of Pascal under DOS C++ under MS-WindowsNT is now used. Several problems could be solved by this, in particular memory management, device drivers for input/output, and user friendlyness by up-to-date windows technology. However also more basic structures were changed. The idea was to utilize as many existing commercially available programs as possible to minimize programming efforts. WindowsNT helps already a lot by MFC technology, but also due to its multi-task facilities. This feature allows to run simultaneously several pro-

Jan 1, 1996

By D. F. Symonds

INTRODUCTION Dense medium processes have been used to separate coal and ores for over a hundred years. In fact Sir Henry Bessemer first patented a process in 1858. In recent years, their importance relative to other gravity dependent processes has increased. This is particularly true in the coal industry where over 60% of all preparation plants operating in 1984 in North America (1) contained either dense medium vessel or cyclone circuits. In addition, the stringent product quality demands of the consumer, together with increases in mining costs, dictate that the cleaning circuits be both predictable and efficient. Dense medium systems are the most predictable and efficient of all gravity- dependent processes. The majority of the text of this chapter will be concerned with dense medium applications as they relate to the coal industry. However, the techniques and calculation procedures can be applied, in general, to all non-coal minerals (such as diamonds, marginal iron and lead-zinc ores and gravel) which take advantage of a difference in specific gravity between the saleable product and the reject. The object in dense medium cleaning is to produce a liquid whose effective specific gravity is between that of the concentrate and the reject. In which case the lighter product will float to the surface and the heavier product will sink to the bottom. Unfortunately, this simple process becomes complicated by the following practical necessities: (a) collecting and removing the float and sink products from the medium without disturbing the free settling effects; (b) maintaining and controlling the specific gravity of the medium; (c) separating and reclaiming the medium once the products have left the separating vessel; and (d) separating finer sized particles which take longer to fall through the dense, and often viscous, medium. As a result of the last issue (item d) two main types of dense medium separators have evolved: dense medium vessels and dense medium cyclones. Dense medium vessels are essentially large baths through which the dense medium flows at a relatively slow velocity. The lighter products float to the surface and are carried out of the vessel by the medium flow. The heavier products sink to the bottom of the vessel and are physically transported out either by means of a conveyor (usually a chain conveyor) or a rotating, lifting arrangement (Figure 1). They generally

Jan 1, 1986

By G. Xu, A. R. Kumar, N. A. Amoah

Prolonged exposure to high concentrations of respirable coal mine dust causes coal workers’ pneumoconiosis and silicosis. Underground coal mine roof bolter operators are more prone to elevated exposure to coal and silica dust. The canopy air curtain (CAC) was developed by NIOSH to protect roof bolter operators from the exposure. The CAC supplies filtered air over the breathing zone of the operator. This dilutes the high coal dust concentrations and provides for an impenetrable air curtain. Many studies have been carried out to improve CAC efficiency. However, field test has shown variable dust control efficiencies indicating rooms to further improve due to the nonuniform airflow distribution across the plenum and ineffective perimeter flow. This study therefore redesigns the CAC with optimized flow distribution that effectively protects roof bolters from coal dust exposures. Computational fluid dynamics (CFD) simulations are used to optimize the uniformity of airflow distribution across the plenum to achieve the best possible uniformity. A lab experiment validates the CFD model and confirms the ability of this design to reduce floor dust pickup, prevent external wind infiltration, and offer an improved protection efficiency

Mar 2, 2022

By Irwin R. Higgins, Richard S. Dennis

Acid recovery employs ion exchange resin as an adsorption media for the separation of inorganic acids from mixtures of acids and their metallic salts. This technology has been used to treat spent pickling and plating liquors to recover acid for reuse in the bath and to reduce waste acid neutralization costs. Acid recovery can also be used for electrolyte treatment to facilitate valuable metal recovery and to improve product quality. Conventional fixed bed ion exchange (I-X) systems are impractical for acid recovery because of complex control design and large resin inventories needed to process strong acid concentrations. TETRA'S CCIX™ continuous I-X contactor has been used successfully in a simple, continuous operating mode to separate acid from its salt. Efficient separation is enhanced by refluxing which allows acid to be produced as a salt-free product at nearly its original strength. Continuous treatment also recovers heat to the bath and improves metal quality due to consistent acid quality.

Jan 1, 1995

By J. A. Porter

This paper uses project examples, primarily associated with large iron ore mines in Brazil, to demonstrate opportunities for the mining industry to go beyond traditional compliance and impact mitigation to proactively operate within the ethics of environmental and economic sustainability.

Jan 1, 1994

By G. T. Adel

Hindered-bed separators are often used in the minerals processing industry to classify particles according to size and density. A new technology, known as the Eriez CrossFlow, was recently developed to overcome some of the limitations associated with hydraulic separators. The innovative feature of this unit is a novel feed presentation system that improves separation efficiency and capacity. In the present work, a detailed process engineering evaluation was conducted to determine the basis for the improved performance of this unit. The evaluation included controlled separation tests using well-characterized feeds, particle and liquid tracer experiments and mathematical modeling studies. Data obtained from this work show that the new separator is capable of maintaining good separation efficiencies at higher solid feed rates than traditional designs due to improved hydrodynamics in the separation zone. This paper reviews the operating principle of the Eriez CrossFlow separator, discusses the results of the tracer experiments and modeling studies and presents test data obtained from recent laboratory and plant trials. Key words: Size classification, CrossFlow separator, Hindered-bed separator, Hydraulic separator

Jan 1, 2003

By W. Blake, J. K. Whyatt, B. G. White

In situ stress on the scale of a tunnel or mine may be distorted by geologic structures. The resulting variations in in situ stress have a direct bearing on the potential for mining-induced seismicity. New evidence collected from the Lucky Friday mine by US Bureau of Mines researchers, as well as a review of previous case studies, demonstrated that in situ stress variations affect the [spatial] distribution of mining-induced seismicity. Although overcore stress measurements have been useful in these studies. they are too expensive and, depending, on conditions, may be too difficult to collect. However, information on borehole and raise breakouts: deformation of mine openings: and patterns of seismicity, ground-control problems and rock-burst damage can be used to build a stress database. In conjunction with maps of mine structure and geology and models of rockmass behavior, this database can then be used to build a map of in situ stress variations. Such a map could provide a means of anticipating patterns of mining-induced seismicity and. Thus, could be the basis for planning appropriate measures to ameliorate rock-burst hazards.

Jan 1, 1997

By J. D. Miller, C. L. Lin

The appropriate software and hardware necessary to adapt an X-ray CT analyzer for the determination of coal washability was developed and successfully tested for well-characterized samples under laboratory conditions. Evaluation of the CT-based analyzer under simulated on-line conditions is also presented to verify the on-line capabilities of the newly developed X-ray CT analyzer for the control of coarse coal cleaning circuits. The investigation shows that the data obtained from CT washability analyses compare favorably with experimental sink float data. Further, image frequency was considered to evaluate the CT-Based coal washability analyzer for simulated on-line conditions. Specifically, the number of observations (image spacing) needed for accurate sampling and the total time required to perform the calculations for a representative data set were determined. Key words: Coal washability, Computer simulation, X-ray CT analysis

Jan 1, 2003

By H. Kempton

New methods for remediating metals-contaminated groundwater include in-situ emplacement of highly adsorptive substrates to permanently retard solutes. Substrates are introduced by sequential injection of soluble components that precipitate in the aquifer, forming a permanent high-retardation zone. This method overcomes the factors that limit pump-and-treat remediation; i.e, long-term source loading and slow desorption. Column tests demonstrated efficient substrate emplacement, increasing retardation coefficients of Cr(VI) by 20 and As(V) by 40. Similar effectiveness is expected for other heavy metals. Simulations using a coupled advective-geochemical model accurately matched substrate emplacement and arsenic attenuation, allowing extrapolation to other constituents and larger-scale applications.

Jan 1, 1999

By U. E. Paakkinen

Progress in computer control of flotation circuits has developed parallel with advances in reliability of on-stream X-ray analysis (Cooper, 1976). Attainment of acceptable results with X-ray fluorescence analysis over the past ten years has led to application of computer control in more than 30 concentrators. Gains in applying flotation control also have given incentive to improving measurement and control devices for other essential functions in control systems. At the same time, advancing technology has made available computer systems having characteristics practical and economical for the physical environments of concentrators and ore processing plants. Benefits from flotation control have centered on increased efficiency in mineral separations, derived by stabilizing circuit operation subject to changing ore characteristics. The gains have been most evident in processing complex ores for multiple concentrate products. In many cases, particularly when coupled with grinding control, the economic results from on-line control have been substantial compared to investments in monitoring and control equipment.

Jan 1, 1979

By B. K. Mishra, B. Das, L. Panda, D. S. Rao

"The dissolution behavior of lateritic nickel ore containing 1.2% Ni, 40.6% Fe, 9.5% SiO2 and 9.59% MgO by sulfuric acid was investigated. The ore was characterized adequately by different techniques such as chemical analysis, scanning electron microscope (SEM), X-ray diffraction (XRD), field emission scanning electron microscope (FESEM), thermal analysis and Fourier transform infrared (FTIR) spectroscopic measurements. The characterization results did not reveal any distinct mineral phase for nickel; it was associated with mineral phases like goethite, hematite, chromite and serpentine in various proportions. The beneficiation studies by hydrocyclone, magnetic separation and flotation did not enrich the nickel value. Reduction roasting followed by magnetic separation indicated only 2%Ni with 28.9% yield. Consequently, the recovery of nickel values from the lateritic ore by acid leaching under different conditions was studied. The kinetics of leaching obey the first order rate equations. The recovery of nickel was found to be influenced by temperature. It was observed that at an acid concentration of 2M, leaching temperature 363 K, time 240 min and solid-to-liquid ratio of 1:10, it is possible to leach out more than 95% Ni.IntroductionThe demand for nickel is ever increasing. Nickel is used to impart specific properties to steel, titanium and aluminium, and also is used in petrochemicals, catalysts, batteries, etc. It has been estimated that nickel oxide ores account for about 70% of the world nickel reserves. However, most nickel is sourced from sulfide ores. Nickel is extracted from sulfide ore by size reduction, followed by flotation to obtain a nickel-rich concentrate. The concentrate is then pyrometallurgically processed by smelting to produce a nickel-rich matte after discarding an iron-rich slag. Due to the increasing demand for nickel in stainless steel and other alloys, nickel is also extracted from many secondary sources. The recovery of nickel from oxide ores is now gaining momentum, and more exploitation of this ore is being attempted by advanced as well as environmentally feasible, cost-effective techniques. Dalvi et al. (2004) has reported that, due to the increase in demand, the world nickel production from laterites is expected to increase every year from the current level of production. In recent years, investigations of the use of low-grade ores, spent catalysts, clays, etc., have intensified to meet the market demand and also due to a shortage of high-grade nickel bearing ores (Al-Mansi and Abdel, 2002; Baba et al., 2009; Ismail et al., 2011)."

Jan 1, 2015

By D. Koren, D. Carson

Disposal of smelter slag may be subjected to regulatory leach tests to deter- mine whether they produce a leachate containing contaminants in excess of stated limits. Contaminants that are most often of concern for smelter slags are As, Cd, Cr, Cu, Ni, Pb, and Zn. The present regulatory tests are based on the assumption of storage in a municipal landfill dump, where wastes are in contact with organic acids. Since slags are not normally stored in such an environment, these tests do not adequately assess the true leachability potential of the slags. Ten slags from six major Canadian nonferrous sulfide smelters were studied. Leaching was done following regulatory and modified tests, including leaching in columns with synthetic acid rain for a 25-week period. The slags were characterized by mineralogical analysis before and after leaching with synthetic rain. The synthetic mineral equivalents (hereafter referred simply as phases) in the slow cooled slags consist of fayalite grains and dendrites, amorphous glass, some spinel and small quantities of complex sulfidic prills and metallics. The phases in the quenched slags consist of amorphous glass, some spinel and small quantities of complex sulfidic prills and metallics. Some metal dissolution took place during leaching. However, for all leaching tests, the concentrations were always below the regulated limits. In general, the content of the potentially leachable elements remains unchanged in the fayalite, in the amorphous glass and in the spinel, whereas the quantity of sulfidic prill and metallics decreases after leaching. Therefore, most of the deleterious element dissolution comes from the sulfidic prills and metallic phases. Metal dissolution increases by crushing the slag, probably due to an increased exposure of the sulfidic prills to the leaching solutions.

Jan 1, 1998

Coal that meets customer specifications is often stored in silos prior to being loaded into railcars. However, it is often found that, after loading, the coal contained in a particular car does not meet customer specifications. This can occur because of the variability inherent in the coal and because of segregation, mixing and flow inside the silo. Some contracts now require the coal in each car to be within specification. Silo flow models are used to predict quality in such cases. However, developing an accurate silo flow model for each case is difficult and time consuming. This paper examines the viability of using an online analyzer in conjunction with a feedback circuit to optimize the quality of the coal being loaded into trains, so that each car meets the quality specifications.

Jan 1, 2002

Because of its many advantages, roof bolting has been widely used in hard-rock underground mines. In this paper, the applicability of roof bolts to mine openings in frozen ground, and the affects of bolts on the stability of the openings are presented. A comprehensive finite-element program, ABAQUS, was used to analyze the temperature distribution, the stress field and the displacement, field around a mine opening. Openings that were supported by roof bolts and openings that were unsupported were both analyzed. The thermal and mechanical processes were treated as a quasi-coupled problem, with the thermal analyses being conducted first, followed by the mechanical analyses in each case. For the opening under consideration, i.e., a roof area of 15 m2, five to seven roof bolts are appropriate. When the number of bolts is less than five, the displacement within the ground can be improved only locally.

Jan 1, 1997

By Hang Yang, Linneas W. Laage

Mine fire emergency planning requires simulation of the interaction of the fire and ventilation system and the subsequent distribution of products of combustion (POC). Several computer models were developed by the Bureau of Mines to perform this simulation. The most recent and advanced program, MFIRE performs normal ventilation network planning calculations, and dynamic transient state simulation of ventilation networks under a variety of conditions. MFIRE simulates a mine's ventilation system and its response to altered ventilation parameters such as the development of new mine workings or changes in ventilation control structures, external influences such as varying outside temperatures, and internal influences such as fires. A major concern of mine fires is the heat- generated ventilation disturbances which can move POC through unexpected passageways. This Bureau paper describes recent in-mine experiments conducted at the Waldo Mine near Magdalena, NM to validate the temperature distribution and heat exchange with rock functions of MFIRE.

Jan 1, 1991

By Donald D. Haas

This presentation will discuss a mine owner's evaluation to utilize a contract miner in the development and production of gold properties. I will address both the quantitative and subjective aspects of the evaluation process. The quantitative aspects include cost evaluation, capital preservation, acquisition and disposal of new and used equipment, administrative costs, recruiting and training, and organizing a staff and craft labor force. The subjective areas of this discussion include corporate philosophy, administrative concerns, contractor competence, loss of owner control, operating flexibility, financing assistance, recruiting and training program utilization and risk reduction. The evaluation of alternatives provides a system for comparing, on a cost basis, an owner/operator system vs. a system using a contract miner. The supplement provides a concept on how a contract miner may be the cost effective system to be utilized.

Jan 1, 1989

By R. A. Bilonick

Sampling is used in all scientific, engineering, marketing, and financial disciplines. The scientific theory of probabilistic sampling is a well established field, providing a general framework for basic methods that can be applied in fields that would appear to have little in common. The revolution in sampling occurred, in part, as a response to the need for quality control in industry during the Second World War. Since this time probabilistic sampling methods have been replacing pre-scientific non-probabilistic methods of sampling. This has not been the case, however, in the mineral industries in the United States. No general agreement on a theory applicable to all sorts of particulate materials has been reached. As a result, non-probabilistic methods are still widely used and the measurement of sampling precision - the hallmark of scientific sampling - is unknown. Much of the research on particulate material sampling that has been carried out over the last 40 years can be characterized by a lack of theoretical reasoning and rigor, an unwillingness to acknowledge previous work, and a lack of integration with existing, established scientific sampling theory. Non-standard statistical terminology is used and often standard statistical terms are misused. The confusion that has resulted is reflected in ASTM and IS0 sampling standards and in the practice of particulate material sampling.

Jan 1, 1986

By J. Devon, D. L. Ewart

Long-term coal mining plans are often based on attainment of an average cost of coal. This is achieved by blending low- and high-cost coal production. Coal that is beyond the economic limit of the reserve is mined in a misguided effort to improve reserve recovery. Long-term contracts should be least cost-based and generate the best net present value from the economic reserve within the context of a rational mine plan. The selected economic reserve should he mined on a low- to high-cost basis to benefit from the time value of money.

Jan 1, 1996