Search Documents

By Joseph D. D?Annunzio

The report on cut and cover construction as assembled by the Organization for Economic Co-operation and Development covered 17 different countries based on a total of just under 400 individual replies of which about 30% of the replies were from the United States. In general, the review of replies to the questionnaire led to the impression that cut and cover construction is a very inadequate method which needed many improvements. This unfavorable judgment, however, resulted in the manner in which questions were asked rather than in the method itself, It can be concluded that the cut and cover construction method has proved itself as an excellent method and that it has reached a high degree of technological perfection, but inadequacies stilt exist, and for purposes of complete evaluation, comparisons with mining tunnelling methods should be carried out. The principal problem in cut and cover construction is the interaction during construction between the construction process and the existing use of the surface and subsurface environment. The greatest impediments to cut and cover construction have little to do with the physical works being constructed, but more with creating a site in which the work can be performed. Utility relocation, traffice maintenance, and protection of existing structures are major problems for the construction contractor, and too frequently receive insufficient attention in preconstruction planning and design. Some OF the areas in which research should be undertaken are as follows:

Jan 1, 1970

By Karl P. Norrena, Clayton V. Deutsch

Ore and waste cannot always be visually separated. The distinction between ore and waste may need to be made on the basis of blasthole sampling. Hand drawn dig limits or computer-generated contour lines do not account for uncertainty, economics or equipment. Geometric methods for interpreting grade information such as the polygonal or triangulation methods share the same limitations as contouring. Geostatistical techniques exist for the realistic modeling of grade variations and uncertainty. Decision analysis techniques exist for the binary classification of ore, and waste blocks in the presence of this uncertainty. Block-by-block classification is not enough; mining equipment cannot exercise free selection of blocks. There is a need for procedures to determine optimal dig limits that account for (1) the uncertainty in the grades, (2) the economics of risk-qualified decision-making, and (3) the ability of the mining equipment to dig to specific limits. This paper presents a procedure for optimal determination of dig limits that account for these constraints. Simulated annealing (SA) is used with modest computational requirements because the number of variables is relatively small. The solution of the optimization problem is dig limits that maximize profit under multiple constraints. The method is illustrated with different constraints and tested against hand drawn dig limits in a "Dig Limit Challenge," which illustrates the efficacy of the new method.

Jan 1, 2002

By S. K. Kawatra

For efficient control of particle size in a wet grinding circuit, three alternative methods for monitoring pro- duct particle size are available. These methods are based on: 1. Ultrasonic wave absorption. 2. Low-angle forward scattering of a laser beam. 3. Inferential sizing techniques. The relative advantages and disadvantages of each technique are discussed. A particle size monitor can be used on a single grinding line to control the product particle size. To minimize the number of particle size monitors at an operation consisting of many similar grinding lines, a portable multi-stream on-line analyzer can be used. The paper outlines the design and the operational characteristics of the portable multi-stream online analyzer.

Jan 1, 1979

By Randal J. Barnes

The nonlinear network optimization algorithm developed in this paper solves the following mine ventilation design problem: find the location and size of all fans and regulators which minimize the overall system power consumption while satisfying all physical, legal, and operational constraints. This work includes the formulation of the problem within the framework of mathematical optimization, the development of the computational theory, and the creation of an efficient solution methodology. The algorithm has been implemented on a microcomputer, and a small but representative example is included. The algorithm presented in this paper has four limitations. First, the optimization process is for a single point in time: the dynamic nature of a mine ventilation system in an evolving mine is not directly addressed. Second, the topology of the ventilation network is required input information. The mathematical algorithm does not optimize the size or location of the mine ventilation airways; however, the post optimality analysis techniques can be used to aid in topological decisions. Third, the problem is formulated using volumetric flow; thus, heat and moisture transfer are ignored. Fourth, the capital cost of ventilation equipment is not included in the formulation.

Jan 1, 1989

By E. R. Braer, C. J. Bise

The trend in underground room-and-pillar coal mining is to employ remote-controlled, continuous-mining machines and extended cuts to depths of 12 m (40 ft) or more. This system of coal extraction, adopted by more than 435 mines, can create additional worker safety hazards. To address the ground-control-related safety hazards, a combination of statistical analysis and numerical modeling was used. Initially, the reported roof-fall incidents and fatalities were reviewed to delineate the ground-control hazards. Then, the application of the coal mine roof rating (CMRR) for estimating safe extended-cut depths was evaluated. Finally, computer modeling was completed to predict roof displacements during extended-cut mining. This paper describes the results of these studies and their impacts on the safety of extended-cut mining.

Jan 1, 2000

By E. F. C. Ferrett

The benefits derived from the use of main fan evasees or diffusers are well known. If a well designed evasee is fitted to a fan either more air will flow through it or the same air flow rate will be discharged at a lower fan speed. This latter possibility will reduce the air power requirement of the mine, the fan input power and the overall energy costs. Despite these apparent advantages, many reports have been received from the industry of poor evasee performance. After examination, it appears that these problems are often caused by installation difficulties or inaccurate design procedures. The performance of an evasee is affected by several independent factors. Some of these factors describe the evasee geometry whilst others are concerned with the behaviour of the air as it passes through the evasee. This paper shows that the divergence angle is by no means the only ;important parameter which affects evasee performance and that the size of the inlet boundary layer has a significant influence. The performance of evasees of differing geometric shape are compared and the criterion to be used for optimum performance is discussed. It is shown that the commonly used evasee efficiency is a poor indicator of good performance. Recent work by the author and others is evaluated and a simple design. guide discussed. For more sophisticated work, details of a. computer program are provided. Finally, a brief resume of the performance of truncated diffusers is given. Since compressibility effects can be ignored for most mining applications, incompressible flow has been assumed for most of this paper.

Jan 1, 1980

By Douglas W. Fuerstenau, Douglas M. Deason

The depletion of high grade siliceous phosphate ores is bringing about a search for economically processable replacements. The processing of unexploited dolomitic sedimentary phosphate reserves has numerous problems including the similar surface properties of the carbonate and phosphate minerals and the presence of significant concentrations of dissolved species in the flotation pulp. In this paper, inorganic adsorption and surface transformation phenomena exhibited by the dolomite/apatite systems are examined in detail. Electrokinetic, adsorption, and flotation results indicate that when placed in a common solution, these two minerals interact significantly, with a corresponding strong influence on flotation using a physisorbed collector. Such behavior can have strong implications for flotation plant practice.

Jan 1, 1993

By Rodrigo Estay Huidobro, Andrés Martinoli, Claudia Pavez-Orrego

The effects of induced seismicity caused by mining activities are one of the main problems that the mining industry faces. Although it has been documented by countries with a great mining tradition (United States, Canada, Australia and Chile) for over a century, the problem has been intensified throughout the years due to the greater depths that mineral extraction reaches, where the stress levels and environmental conditions increase the possibility of a rockburst occurrence. Seismic events inside the mine cause important losses of human lives and infrastructure damage. To deal with this problem it is necessary to implement several kinds of safety protocols. For example, seismic indicators allow to identify, through the analysis of a set of seismic parameters -magnitude, energy, time, decay rate, among others-, periods of time when a seismic event of considerable magnitude is most likely to occur. The objective of this work is to use the frictional energy generated by a microearthquake inside the mine as a seismic indicator, linking it with the occurrence of large magnitude seismic events which are outer the background activity. Thus, we seek to determine the set of seismic parameters which allow the best performance of the frictional energy/heat indicator. In the present study, we considered magnitude, frictional energy, and time as seismic parameters to study the efficiency of the proposed indicator. The optimal set of parameters was determined using two different methodologies: accumulated thermal energy and alert bands. The Piece Skill Score and the Accuracy indexes were used to evaluate each set of parameters. Both approaches show a high rate of true positive and true negative hits. Furthermore, it was concluded that both methods show complementary results in terms of the detection of critical events (Mw > 3.0).

Apr 26, 2022

By Carlos E. Avila, Ronald D. Evans

The results of an experimental research program to measure the non- Darcy flow coefficient as a function of temperature and overburden pressure are presented. The experimental values of the non-Darcy flow coefficient were measured over a temperature range of 70-200°F (21°-93"C)and overburden pressures of 1000-4000 psia (68-272 atm). The data obtained confirm that the non-Darcy flow coefficient is a function of rock and fluid properties and is not solely dependent upon the former has been routinely assumed in the literature.

Jan 1, 1986

By J. R. Sturgul

Thompson and Adler (1988) present a new simulator for use in designing conveyor belt systems for underground mines. Their model uses a large Fortran program to do a Monte Carlo simulation. Their approach is similar to that done by other researchers, such as Stanford (1965) and Newhart (1977). All Fortran based simulation models use an imaginary clock that is advanced a time increment. At each advance of time increment the program has to determine what is to take place in the system. Since many things can take place at different places in the system, this approach requires that a large amount of logic is needed at each step of the program. This, then, necessitates a great amount of jumping between different portions of the program. In fact, the Fortran program, CMBCS, takes up to 15 to 20 minutes to run on the mainframe and several hours for the PC. Such execution times are typical of Fortran based simulation studies. There have been other examples of Fortran based simulation studies in mining. Cross and Williamson (1969) presented a model of a working open-pit copper mine. Fosinato (1982) presented a model of the bucketwheel excavators for the large open-pit mines in Southern Victoria in Australia. These excavators discharge into a complex conveyor system, which can be thought of as being similar, but more complicated than the one modeled by CMBCS. All previous simulation studies using Fortran as the source code have several things in common: they all are very lengthy, often being of the order of 10,000 lines of code and take a great deal of CPU time to execute. The program of Fosinato takes more than 4.5 hours to run on a large mainframe. Also not mentioned by Thompson and Adler is the actual time it took to write the Fortran code. This, too, can be considerable, as Fosinato's program took several man years to write and de-bug. In order to change it, as the parameters change or as the mine increases, further large amount of time is needed. An alternate to such Fortran based programs is provided by using a special computer language known as General Purpose Simulation System (GPSS). This language is designed to solve a wide variety of discrete event simulation problems and appears to be particularly suited for mining situations as shown by Sturgul and Yi (1 987). Although GPSS was introduced as far back as 1961, it has not been used in mining to any great extent. However, the original form was quite crude and inefficient compared to modem versions. Perhaps with the increasing popularity and availability of these recent versions, this will change. Two such versions are GPSS/H for the mainframe and GPSS/PC for the personal computer. GPSS/H allows for interactive usage, such as allowing input data to be entered via a menu. GPSS/PC has excellent graphical capabilities and one can actually view the simulation in progress. In addition, one can halt the simulation and change values of various parameters. If a particular portion of the simulation is in progress via a concept known as "microwindows." These new versions have greatly increased the potential for using the language for mining situations. Mining applications of GPSS have been given by Sturgul and Yi (1987), Sturgul and Harrison (1987), Sturgul (1987), and Sturgul and Singhal (1988). Schriber (1987) presents a summary of the recent advances in GPSS.

Jan 1, 1987

By D. W. Park

Longwall mining is popular in underground coal production in the United States due to higher production rates and safety concerns. Because of the extreme complexity, it is necessary to plan an adequate design to achieve a safe and efficient working place. The proper sizes of yield and abutment pillars and panels can be determined by simulation using numerical modeling techniques. By means of three-dimensional modeling, stresses to be imposed on the pillars, panels, gob, and powered supports can be analyzed. In this study, an initial three-dimensional finite element model was developed and then modified into four different models. Using these models, the numerical outputs of distributed stresses on three different sizes of yield pillars, three different sizes of panels, and two different sizes of abutment pillars were compared and analyzed to determine the most adequate pillar and panel sizes. Progressive failure theory based on the Hoek and Brown failure criterion was used to determine redistribution of stresses in the yielded and failed areas in the longwall mine.

Jan 1, 1992

By J de Cuyper, V. M. Lovell, W. Freyberger

The recovery of apatite from the phoscorite ores occurring in the Transvaal, Republic of South Africa, involves a flotation process that is particularly difficult to characterize from a fundamental point of view. However, the reagents used, (tall oil fatty acid, nonylphenyltetraglycol ether, sodium silicate, and sodium hydroxide) can successfully bring about a separation of apatite from dolomitic calcite, which is the most troublesome gangue component. Recently, it has been demonstrated with some flotation feeds that the addition of certain polysaccharides can improve the flotation significantly. It has been shown that the metallurgy obtained is closely linked to the nature of the froth, and this, in turn, is influenced, often dramatically, by the presence or absence of certain of the reagents. The character of the froth depends less on the inherent frothing ability of these reagents than on the presence or absence of fine mineral particles in the froth, and on their surface characteristics and state of aggregation. The polyglycol ether and the polysacchar- ides have been shown to affect these properties, and it is suggested that a major function of these reagents is to modulate the properties of the fine particles in the pulp, thereby changing the character of the froth and giving rise to improved results.

Jan 1, 1976

By Pieter C. van Aswegen, J. A. Brierley, C. L. Brierley

The bacterial-oxidation (BIOX®) process for the pre-treatment of refractory ores for gold recovery is marketed by BlOMlN Technologies S.A. The process was originally developed by GENMIN who is still providing testwork, design and commissioning assistance to BIOMIN. Since 1986 three BIOX® plants have been commissioned by GENMIN. A further two plants will be commissioned during 1993 and 1994. The commissioning and operational experiences from these plants are described in the paper.

Jan 1, 1993

By Cleophus Short

[Of the many occupations in and about the coal mines, those of the haulage crews are among the most hazardous. Statistics ship that the second greatest number of fatalities about the coal mines occur during haulage ion and through the use or misuse of haulage equipment. During the five year period between January 1, 1957 and January 1, 1962, the m stone mine had a. Sack haulage frequency of 4098 and mined 3, 541,939 toads per haulage fatality. Coal mire haulage is similar in respects to railroading. We gee very serious consideration to the instillation of tack and to the selection of the haulage crews. In doing this, we are attempting to have our coal mine haulage as. Safe as that of the railroads.]

Jan 1, 1963

By Daryl R. Tweeton

The Bureau of Mines has developed PC-based tomographic computer programs for geophysical applications, and is making them available to potential users as part of a Bureau plan to facilitate the transfer of technology to industry. These programs were initially developed for predicting and monitoring the flow pattern of leach solution during in situ mining. Seismic crosshole tomography has located fractured zones of low seismic velocity and saturated zones of high seismic velocit above the natural water table. The Bureau has applied tomography also to assessing high-wall blast damage, and examining the integrity of mine-related geological structures. The tomographic programs include the straight ray pro ram BOMTOM (Bureau of Mines Tomography? and the program BOMCRATR (Bureau of Mines Curved Ray Tomographic Reconstruction) that can be run with either curved or straight rays. Both programs provide optional mathematical constraints to help counteract the nonuniqueness of reconstructions that occurs with crosshole data. They are available from the Bureau free of charge. With typical data sets, they can be run on a 386 microcomputer with 640 Kb RAM. BOMTOM was described in the Bureau Report of Investigations 9159, so this report emphasizes BOMCRATR. Curved and straight ray reconstructions using seismic field data collected while simulating injection of leach solution were compared. The curved and straight ray tomograms were quite similar even with velocity variations of more than 50 percent.

Jan 1, 1992

By A. M. Tunstall

Blasting is commonly viewed separately from mechanical handling and crushing. This view is misleading because the degree of fragmentation achieved by blasting can have a significant effect on the efficiency of these processes and, hence, on the overall cost of the mining operation. In this paper, aspects of blasting and crushing and their interaction are examined. A case study is also presented that dramatically illustrates the influence of blast fragmentation on subsequent processing and on the financial implications involved.

Jan 1, 1998

By Andrzej Frycz

The development of the theory of reliability creates more and more possibilities of its application in different domains of technics. The methods evolved to date, both theoretical analysis of the engineering systems and investigations techniques in practice can be put in use a d translated from one science to another one [1,3,7J . It needs to consider the specific of the different sciences. But it is necessary to take account of the specific characteristic of each line of science. The reliability investigations needs, justified in technical and economical viewpoint appear too in mine ventilation technics and systems. The mine ventilation system is a complex of workings and ventilation plants, which serve to supply the networks with a sufficient quantity of fresh air from the atmosphere and then carry off the vitiated air. The condition necessary for a ventilation system to perform definite task is the correctness of all its elements, that is a capability to preserve in a expected range of tolerance, the values of basic parameters. The element of a system which ceases to work correctly is called failed. The basic parameter of all elements of a ventilation system is the characteristic curve, pressure loss - air quantity relation ?p = f(Q) (1) This curve concerning the workings and ventilation stoppings is given by the formula: ?p = R Q2 (2) thus the resistance R (of the workings or stoppings) may be taken as a characteristic parameter. The course of this characteristic f(Q) will be given in a complex form in concern with fans, ejectors, air curtains. The failure of a ventilation plant or working is therefore an event, relying on a change of its characteristic, thus for a definite time the losses of the plant's or working's capability set in for the fulfilment of its function in the ventilation system. The failures are divided in viewpoint of their nature on sudden and progressive. We are in concern with the sudden failures which are characterised by a violent change of the ventilation element parameter for example a fall of roof, or silt up of the working, opening or failure of the ventilation stopping, the stand-off of the fan or ejector etc. We distinguish two kinds of failures on the viewpoint of their action on the air flow: the "opening" failure and "closure" failure. The prevalence of factors, which causes the failures is in connection with the intersection in the mine of roads of haulage, roads of underground transport of materials and lining elements, roads of people motion with airways, as also depends on the rock pressure reaction on the workings lining and plants placed there. Other factors will yet be decisive upon supply decay of fans, ejectors and curtains. The appearance of failure of the ventilation element is therefore of random nature and determines the change of the element, when it is passing from operating state to unoperate. Qualifying the ventilation system element to one of these states is easy, when the characteristic change is clear and occurs suddenly, that was assumed. The investigations conducted by Patrushev and Karnaukh [91 in concern with the ventilation stoppings resistance change in the case of their opening, had shown the possibility of resistance value change in the range of several hundreds higher.

Jan 1, 1980

By B. Markovic

Performance of mineral filler particles in ceramic applications can be enhanced markedly by adsorbing polymers of optimum molecular structure and dosage. In a recent work by Chen and Somasundaran (1997), a novel scheme of controlled polymer adsorption was used to produce nanocomposites of unique core-shell designs. Towards this purpose, adsorption and desorption behavior of selected polyacrylic acids (PAA) on three minerals; alumina, titania, and silicon carbide, was examined as a function of relevant parameters. Adsorption of P AA was found to depend on polymer molecular weight, pH, as well as solids loading. Specifically, the adsorption density was found to increase with increase in polymer molecular weight for non-porous alumina while it was found to decrease in the case of porous alumina. This is attributed to the inaccessibility of the pores to the larger polymers. An unexpected finding was the change in the adsorption density of PAA with solids loadings. PAA adsorbs on silicon carbide only at low pH values when the particles have very low surface charge suggesting that the adsorption in this case is controlled by electrostatic forces. Using polyacrylic acid as bridging agent between the alumina fillers (core) and nanosize alumina or titania particles (shells), controlled layer by layer deposition of nanoparticle on the core particle surface could be obtained.

Jan 1, 1997

By G. Karahalios

Industrial minerals always play an important part in the technological growth of a country. The extraction and trading of industrial minerals continues to expand, but the industry is now subject to stricter environmental guidelines. This paper presents the current status and growth potential of industrial mineral exploitation in the southeastern European region, i.e. Albania, Bosnia-Herzegovina, Bulgaria, Croatia, the Former Yugoslav Republic of Macedonia, Greece, Italy, Serbia and Montenegro, Slovenia and Turkey. Annual production figures per country are presented for 1992-1998. These figures are compared to each other, and, where applicable, they are compared to world production figures. The marketing of industrial minerals to Europe and other regions of the world and the effects of such trade on the local economies are also evaluated when such data are available.

Jan 1, 2000

By D. J. Hutchinson, S. Nickson

Cable bolts are used as a means of rock support around underground excavations in many mines across Canada and around the world. A substantial body of research on cable bolting was conducted at a number of Canadian universities and mines from the mid-1980s through the 1990s. Since then, research into selected areas of cable bolting practice has continued in Canada. The research has focussed on cable bolt instrumentation and on the inclusion of cable bolts in empirical stope design techniques. A review of cable bolting practice is now warranted at many mines. It has been five years since the completion of the previous substantial body of Canadian academic research and the associated advancement in understanding of cable bolt design, implementation and verification practice. Attempts were made at that time to transfer the new design procedures and performance assessment technologies to mine-site personnel. In some cases, this was effective, and ground control personnel continue to improve on their cable bolting practice at each specific mine site. However, at other sites, experienced people have moved on, and the new, less experienced personnel do not have access to the training or technical resources required to improve their understanding of the subject. In other cases, the technology was not transferred effectively to practitioners, with the result that substantial improvements can be made to the cable bolting practice at those mines. Guidelines for auditing cable bolting practice are provided in this paper. The guidelines include a discussion of the objectives of the audit, suggestions for audit procedure and a summary of the possible outcomes of a cable bolt audit. The objectives of an audit might include assessing the reasons for unexpected cable bolt failures, evaluating the quality of the installation procedures, quantifying the efficiency of the cable bolt system and assessing training requirements and procedures. A cable bolt audit should include consideration of all aspects of the cable bolting cycle, including the design, implementation and verification phases of the operation. At the end of the audit, a ranking should be assigned to the components of the cycle. The ranking system can then be used to identify items that require immediate attention, others that could be improved and others that are adequate. Following completion of a cable bolt audit, increased confidence in the support system and its application is generally, found, along with the potential for cost savings in many cases.

Jan 1, 2002