Search Documents

By C. M. Rule

Stirred milling using either horizontal or vertical mills has made a rapid entrance into PGM ore and tailings concentrator flow sheets. Currently there are in excess of 40 units installed in either mainstream, ?MIG? or intermediate concentrate regrind, ?UFG?, applications in PGM, primary ore treatment plants or in tailings scavenging and reclamation treatment plants. This represents a total of approximately 70 MW of installed fine grinding equipment. This paper outlines the reasons why the technology take-up has been rapid and illustrates the advantages of this technology over conventional milling. Keywords PGM, platinum group metals, UG2, Merensky, platreef, stirred milling, MIG?mainstream inert grinding, UFG?ultra fine grindingof intermediate flotation concentrates, IsaMill?, Metso SMD?, Deswik, ceremic grinding media, QEMSEM, MLA.

Jan 1, 2011

By Y. Jin

Magnesia ramming materials have been widely used in China instead of magnesia bricks as furnace lining materials of ferroalloy refining furnace. The paper introduces the development of the ramming material, recounts its chemical composition, physical property and application characteristics. Because of its high MgO contents and fine sintering property, the ramming furnace bottom has the properties of good refractory, monolithic construction and thermal shock resistance. The changes in mineral composition and furnace tearout characterization show the reasons for the bottom?s long service life. The obvious benefits are widely achieved, the annual saving cost in refractory is about 2 millions US dollars.

Jan 1, 2004

By C. Legote

"This paper investigates the conditions leading to the indefinite termination of production in four critical primary panels at an underground coal mining operation, the observed shortcomings in the mining approach, and the proposed strategy to mine through the affected panels. Initial assessment of the abandoned panel conditions indicated time-dependent strata failure,(i.e. bolted roof failure overrunning intersections), which occurred from mere minutes to up to four weeks post-production, with and without prior warning of failure. This prompted the constant re-supporting of back areas, which raised safety and productivity concerns. Investigation of the initial mining conditions revealed that the failures were due to a critical combination of factors, the chief of which was isolated horizontal stress. Other factors that were initially overlooked by the mine (i.e. influence of hydraulic stress, misinterpretation of borehole data), resulted in the conditions being described as abnormal. Remedial actions were determined, and in so doing, a new strategic approach was formulated to thoroughly address all failure concerns. The four panels were explicitly planned to serve as the main intake and return airways for the recently commissioned secondary ventilation shaft, as well as providing access to millions of tons in proven coal reserves. It is thus imperative to mine the panels. A feasibility study showed that the proposed strategy set for implementation would be financially viable. Paper written as project work carried out in partial fulfilment for BEng(Mining Engineering) degree"

Jan 1, 2015

By H. P. Kritzinger, T. C. Kingsle

"Rotary kilns are used for a variety of mineral processing operations. Hatch makes use of a kiln model developed from first principles to evaluate designs for its clients. This tool has been applied to a variety of pyrometallurgical applications, including ferrovanadium, nickel carbonate, nickel laterite, iron ore reduction, and spodumene (lithium) production.This paper illustrates the application of numerical optimization techniques in combination with the kiln model in the interrogation of a generic iron ore reduction process. The fundamental modelling concepts are explained, followed by a description of the optimization approach. The results show how the combination of the two methods, with modern computing power, can generate a large number of viable design and operating candidates."

Jan 1, 2015

By J. Dienenthal

Automatic Charging and Stoking Machines for use at ferroalloy furnaces are in operation for more than 20years. Dango & Dienenthal Maschinenbau GmbH (short: DDS) has developed several machine generations. Today advanced solutions help to achieve better charging and stoking results to minimize cost and to improve the working environment around the furnaces. Three different alternatives can be considered: Rail-mounted solution The machine(s) travel(s) on an overhead monorail to one or several furnaces and is locked in the desired working position from where charging and stoking is performed. Mobile solution This machine travels on the charging platform and is also locked at the respective working position to perform charging and stoking. Automation of a standard mobile charging and stoking machine A standard charging and stoking machine can be adapted for automation. A reliable navigation system is included. Charging and stoking is performed with the moving machine. Advantage versus other solutions: considerable lower investment cost and possibility to upgrade the mobile charging and stoking machine for later automation. Overall, automatic charging and stoking can save up to 10 per cent of the specific smelting energy. A better and more consistent furnace operation can be achieved. Different programs are used to cope with different furnace conditions and changing raw materials. All machine movements can be recorded and correlated to other furnace parameters. Working environment on the charging platform is greatly improved.

Jan 1, 2007

By L. Linzer, J. Oelofse, T. Rangasamy

Extraction of isolated blocks of ground with elevated levels of stress and/or seismicity is a common occurrence in South African gold mines. Isolated blocks of ground that are divorced from the main orebody and are bound by complex, dip and strike parallel, non-persistent geological structures dominate the Klerksdorp gold fields. No quantifiable methods exist to assess the risk associated with mining these and other classes of remnants. A case history, from a gold mine that planned to extract three remnant blocks hosted in a large complex fault system, is used to illustrate the decision making process based on a combination of underground observations, numerical and seismic techniques. Simple risk estimation matrices were developed and used to estimate remnant-mining risk and finally to quantify the decision on which of the three remnant blocks could be extracted at the lowest possible geo-mechanical risk. Il est courant dans les mines aurifères sud-africaines d’extraire des blocs de terrain isolés qui possèdent des niveaux élevés de contraintes et/ou sismicité. Les régions aurifères de Klerksdorp sont dominées par des blocs de terrain isolés qui sont séparés du gisement principal et qui sont retenus par des structures géologiques non continues, à parallèle de pendage et direction, et complexes. Il n’existe pas de méthodes quantifiables pour évaluer le risque associé à l’extraction de ce genre et autres genres de résidus. Une observation de cas, celle d’une mine d’or qui avait l’intention d’extraire trois blocs de résidus qui se trouvaient dans un grand système complexe de faille, est utilisée pour illustrer le processus décisionnel basé sur une combinaison d’observations souterraines, et de techniques numériques et sismiques. Des matrices simples d’estimation de risque furent développées et utilisées pour estimer le risque lié à l’extraction des résidus et finalement pour quantifier la décision sur lequel des trois blocs de résidus pouvait être exploité au moindre risque géo-mécanique. Die Extraktion isolierter Gesteinsblöcke mit erhöhtem Spannugsniveau oder Seismizität ist in südafrikanischen Goldminen üblich. Isolierte Gesteinsblöcke, die von der Haupterzader getrennt und durch komplexe, parallele abfallende und horizontale nicht persistent geologische Strukturen gebunden sind, beherrschen das Klerksdorp Goldfeld. Es gibt keine quantifizierbare Methoden die das Risiko welches mit dem Abbau dieser und anderer Klassen verbunden ist beschreiben. Eine Fallstudie einer Goldmine, welche die Extraktion von drei in einem großem komplexen Verwerfungssystem eingelagerten Einschlußblöcken plante, wird verwendet um den Entscheidungsprozeß zu illustrieren, der auf einer Kombination von Untertag Beobachtungen und numerischen und seismischen Techniken basiert. Einfache Gefahreinschätzungsmatrizen wurden entwickelt und angewendet um das Abbaurestrisiko abzuschätzen und letztendlich die Entscheidung zu quantifizieren, welcher der drei Einschlußblöcke unter dem niedrigst möglichen geo-mechanischen Risiko extrahiert werden konnte .

Jan 1, 2003

Current mine production planning, scheduling, and allocation of resources are based on mathematical programming models. In practice, the optimized solution cannot be attained without examining all possible combinations and permutations of the extraction sequence. Operations research methods have limited applications in large-scale surface mining operations because the number of variables becomes too large. The primary objective of this study is to develop and implement a hybrid simulation framework for the open pit scheduling problem. The paper investigates the dynamics of open pit geometry and the subsequent material movement as a continuous system described by time-dependent differential equations. The continuous open pit simulator (COPS) implemented in MATLAB, based on modified elliptical frustum is used to model the evolution of open pit geometry in time and space. Discrete open pit simulator (DOPS) mimics the periodic expansion of the open pit layouts. Function approximation of the discrete simulated push-backs provides the means to convert the set of partial differential equations (PDEs), capturing the dynamics of open pit layouts, to a system of ordinary differential equations (ODEs). Numerical integration with the Runge-Kutta scheme yields the trajectory of the pit geometry over time with the respective volume of materials and the net present value (NPV) of the mining operation. A case study of an iron ore mine with 114 000 blocks was carried out to verify and validate the model. The optimized pit limit was designed using Lerchs-Grossman?s algorithm. The best-case annual schedule, generated by the shells node in Whittle Four-X yielded an NPV of $449 million over a 21-year mine life at a discount rate of 10% per annum. DOPS best scenario out of 2 500 simulation iterations resulted in an NPV of $443 million and COPS yielded an NPV of $440 million over the same time span. The hybrid simulation model is the basis for future research using reinforcement learning based on goal-directed intelligent agents.

Jan 1, 2008

By G. L. Smith

This paper introduces and defines the concept of a linkage between long-term planning parameters (?global assumptions?) and possible future world views as conceived in scenario planning. Scenario planning, the tool that is used to arrive at plausible future worldviews, is described in the context of the platinum industry. The interpretation of the scenarios into long-term planning parameters is made, followed by an illustration of how the long-term planning process has been adapted at Anglo Platinum to include the notion of uncertainty.

Jan 1, 2008

By John W. Harbaugh, Alfredo Prelate

The goal of the study described here is to develop objective. quantitative methods for estimating the outcome probabilities of exploratory oil wells. The study employs the 're-experience' approach, in which historical data are used in a manner which attempts to recreate the past. Our past experience, of course, is the principal guide to the future. To appraise present-day oil prospects, however, we must analyze prospects that have been drilled in terms of how these former prospects were interpreted before they were drilled. An analysis of how they are interpreted after they were drilled is an inadequate guide to the future because our hindsight knowledge is superior to our foresight knowledge. Objective calculation of future outcome probabilities, then, requires that we attempt to treat past information in a manner analogous to that in which we must treat present information in forecasting future outcomes.

Jan 1, 2014

By L. A. Matthews

The embrittlement of the Ti-6Al-4V alloy by hydrogen dosing at elevated temperature has been investigated. Metal coupons were subjected to isothermal treatments in a partial hydrogen atmosphere in the temperature range from 650ºC?950ºC and the degree of embrittlement after treatment was determined by drop-weight impact testing. Embrittlement was found to be inversely related to reaction temperature as a result of the combined effects of greater hydrogen absorption and titanium hydride precipitation at the lower isothermal temperatures. Keywords Titanium, hydrogen embrittlement, impact energy

Jan 1, 2011

By M. Jeffrey

This study investigated the elution of precious and toxic metals from activated carbon. Gold and mercury are of primary interest, due to their value and environmental impact respectively. A laboratory elution rig was commissioned to simulate industrial Zadra and AARL carbon elution conditions. Mercury was found to elute most effectively in strong caustic cyanide solutions; gold was found to elute most effectively in hot low ionic strength solutions. As cyanide decomposes on contact with activated carbon at high temperatures, optimum elution conditions for gold conflicts with those for mercury?no practical compromise in conditions was found. However, sequential elution allowed reasonable recovery of both metals. Ongoing work is looking at the deportment of other metals under elution conditions.

Jan 1, 2009

The estimation of the spatial variation of the b-value of the Gutenberg- Richter relationship is important for both the general interpretation of the mechanism of rock mass response and seismic hazard assessment. The interpretation of b-value as a parameter of rock mass response is discussed in this paper. The methods applied to evaluate the spatial variation of b-value and the algorithm for obtaining the magnitude of completeness and b-value for subsets of data are presented with some verification analyses. The algorithms presented enable the automation of a spatial evaluation of b-value.

Jan 1, 2014

By W. Abdellah

The purpose of this paper is to establish a qualitative method to estimate the risk level (e.g. rating and ranking) resulting from mining activity. Risk is the product of two factors: probability of failure and cost of consequences. A resultant assessment scale matrix is then used to assign a risk index value which is directly proportional to the potential for excavation instability. A case study, the No. 1 Shear East orebody at Vale?s Garson Mine in Sudbury, Ontario will be examined. A three-dimensional, elastoplastic, finite difference model (FLAC 3D) is presented for a mine development intersection situated 1.5 km below ground surface. The developed assessment scale matrix is used to estimate risk index for intersection (2981) located on 5000 level. The results are presented and categorized with respect to risk-index value, probability of instability, cost of consequence, and mining stage.

Jan 1, 2014

By R. Dippenaar

Traditionally, iron ore has been reduced with coke in a blast furnace and the hot-metal product of the blast furnace containing carbon, manganese, silicon, sulphur and phosphorous, was subsequently refined in a steelmaking furnace. During iron making as well as during steelmaking, significant amounts of slag are produced. Two decades ago, more than 13 m tonne of blast furnace slag and 4 m tonne of steelmaking slag per annum were produced in the USA alone. It is, therefore, not surprising that many attempts have been made to re-use iron and steelmaking slags. However, these slags are not merely metallurgical waste products but, on the contrary, their compositions and physical properties are judiciously designed to optimize the operations in the respective metallurgical reactors. The variation in composition and properties of blast furnaces lags are largely determined by the gangue in the ore and ash in the coke and much progress has been made in the re-use of such slag. With respect to steelmaking slag, emphasis has in recent years been placed on hot-metal treatment before refining and ladle treatment after decarburization. The bulk removal of silicon, phosphorous and sulphur from the hot-metal product of the blast furnace by specially designed slags prior to refining in a basic oxygen furnace, has reduced tap-to-tap time, lowered cost and produced steel of much higher quality. The use of synthetic slags in ladle refining techniques subsequent to decarburization in the basic oxygen furnace has resulted in reduced hydrogen and nitrogen contents and reduced solute impurities. Moreover, inclusion shape and composition control, again by the use of specially designed slags has led to the achievement of much improved mechanical properties of the steel. In these revised process routes, slag of different compositions are produced in the variety of unit processes and hence the re-use of steelmaking slags has become much more complex. Clearly, a thorough understanding of the design and use of these different slags is a pre-requisite to the development of re-use strategies. Japanese steelmakers have spearheaded attempts to reduce slag volumes in the individual unit processes and to strive towards ‘slagless steelmaking’ by recycling slags internally. Steelmaking slag volumes have been reduced on commercial scale from about 140 kg/tonne steel to 60kg/tonne steel. Moreover, model predictions have shown that, in principle, all slag can be recycled and the phosphorous extracted to produce fertilizer. This development is of particular significance since the supply of low-phosphorous iron ores is diminishing at an ever increasing rate. Keywords: slag, environment, iron, steel,

Jan 1, 2004

By M. Lange

The postulation that primary platinum group metal (PGM) matte will chemically react with magnesia-chrome bricks when temperatures exceed 1500°C was tested. Magnesia-chrome brick samples were heated in contact with matte at 1300°C to 1750°C for 30 minutes, after which the refractory samples were analysed using reflected light microscopy and scanning electron microscopy. The samples were all completely penetrated by matte. As the temperature increased the matte also penetrated the fused aggregate grains and disintegrated them. The chromium concentration of the matte inside the refractory samples was found to be slightly higher than that of the bulk matte. At temperatures of 1500°C and higher, MgO, FeO, and magnesium-rich silicate crystals could be identified in the matte directly adjacent to the refractorymatte interface. Phase relations clearly indicated that chemical reactions take place between primary PGM matte and the magnesiachrome refractory material at temperatures above 1500°C, but that these reactions are more complex than expected from FactSAGE® calculations.

Jan 1, 2014

By H. Saroglou

The anisotropic behaviour of Athens Schist has been brought out through the testing of specimens with varying orientation of schistosity with respect to the major principal stress under uniaxial, triaxial and dynamic conditions. A large number of results from tests on intact rock specimens of the Athens Schist were statistically analysed and evaluated.

Jan 1, 2004

By B. Leong, H. Joubert

Keywords: Pyrometallurgy, furnace, auxiliary equipment, copper slag launders Pyromet has designed copper launders for tapping slag. What makes Pyromet?s launder design innovative and safe is that it does not have any cooling water channels underneath the launder runner, whilst achieving effective cooling of the runner. If matte burn-throughs were to occur through the launder runner, the risk of damaging water channels and the risk of explosions are reduced. In addition, since the cooling water channels are not harmed, the launder is easily repairable and reusable. Pyromet makes use of Finite Element Analysis to optimize the launder geometry to ensure that sufficient energy is removed from the centre of the launder. Factors considered during the launder design include the suitability of the geometry to the client?s needs, experience from existing installations, and ease of fabrication. Pyromet goes so far as to develop procedures for fabricators to ensure that fabrication issues do not compromise the functionality of the launder. When launder orders are received by Pyromet, the entire fabrication process and the functioning of the launders during operations are monitored to ensure that the launder designs are continuously improving with every installation.

Jan 1, 2006

By A. H. Swart

Unplanned stope panel collapses occur on most near-surface and shallow mines in South Africa. Although these incidents often occur during blasting, they pose a major threat to the safety of underground workers and the economic extraction of orebodies. Most stope panel collapses occur due to excessive panel lengths (resulting in excessive stope spans) that are not designed according to a systematic design procedure or methodology. Instead, panel lengths are often dictated by the equipment in use and by previous experience under similar conditions. Hence, a rock engineering design methodology for the design of stable stope panels between pillars is of vital importance for optimum safety and production in shallow mining operations. Using the proposed design methodology described in this paper, rock mechanics practitioners and mine planners should be able to identify and quantify the critical factors influencing the stability of stope panels. The critical factors should then be used as input to the design of stable stope panels that will provide the necessary safe environment for underground personnel working in stopes. The proposed design methodology is an iterative process, which includes aspects such as rock mass characterization, estimation of rock mass properties, identification of potential failure modes, consideration of appropriate stability analyses and other elements of the rock engineering design process. This process continues after implementation. During monitoring, new data should be included in the database and the design process repeated on a regular basis. Design approaches included in the proposed design methodology include empirical methods such as different rock mass classification methods, analytical methods such as elastic and Voussoir beam analyses, kinematic analyses, probabilistic analyses, and numerical analyses. Keywords: stability, stope panels, design methodology, hardrock mines, shallow mining operations

Jan 1, 2005

By J. Sjöberg, P. Lundman, E. Nordlund, C. Quinteiro

Abstract In the Kiirunavaara underground mine, crude ore is transported through ore passes from the production levels to the main haulage level. Failure and stability problems have occurred in some of these ore passes, with increasing frequency as mining depths increase. In this paper, selected results are presented from a research project run by LKAB. The presentation focuses specifically on stability analysis. Numerical models were used to identify failure mechanisms, in conjunction with empirical data and engineering judgment. The most important controlling factors governing failure and damage in ore passes were quantified. A causative model was established in which failure mechanisms and failure development were described. This model was used to formulate a prognosis of future ore pass stability, and for recommending remedial measures. Résumé Le transport du minerai entre les niveaux de production et le niveau principal de transport, à la mine de fer de Kiruna, se fait par des passes à minerai. Avec la profondeur d'extraction grandissante, les problèmes de stabilité au niveau de ces passes à minerai se sont multipliés. Les résultats d'un programme de recherche sur la stabilité des passes à minerai à la mine de fer de Kiruna sont présentés dans cet article. Les mécanismes de rupture ont été identifiés à l'aide de modèles numériques, de données de terrain et du jugement empirique des ingénieurs. Les facteurs principaux controllant l'instabilité des passes à minerai ont aussi été quantifiés. Un modèle a été établi dans lequel les mécanismes de rupture et le développement des dommages ont été décrits. Ce modèle a été utilisé à fins prédictives et remédiatives. Zusammenfassung In der Grube Kiirunavaara wird das gewonnene Erz über Sturzschächte von den Abbauebenen zu der Hauptförderebene gefördert. Mit zunehmender Tiefe des Abbaus sind vermehrt Standsicherheitsprobleme in den Sturzschächten aufgetreten, die teilweise zu Verbrüchen geführt haben. In dem vorliegenden Beitrag werden ausgewählte Ergebnisse einer Forschungsarbeit des LKAB präsentiert. Dabei wird der Schwerpunkt auf die Standsicherheitsuntersuchungen gelegt. Zur Ermittlung der Bruchmechanismen wurden numerische Modelle in Verbindung mit empirischen Daten angewendet. Die wichtigsten Einflußfaktoren für das Versagen der Sturzschächte wurden ermittelt. Es wurde ein Modell zur Beschreibung der Bruchmechanismen und des Versagensablaufs aufgestellt. Dieses Modell wurde verwendet, um die Standsicherheit zukünftiger Sturzschächte zu prognostizieren und um Sanierungsmaßnahmen zu erarbeiten.

Jan 1, 2003

By Ö. Uysal

This study deals with the presentation of the mechanized longwall mining project introduced some years ago to increase productivity and output of Aegean Lignite Establishment (ELI) owned by Turkish Coal Enterprises (TKI.) and the comparison of this method with a planned alternative new mining method called ?shortwall mining? where continuous miners will be introduced as primary coal excavation machines. Following the planning phase, production costs have been calculated for both mining methods on the basis of a panel having a height of 7.5 m. In addition to cost analysis, both methods have been evaluated using ?the multi-dimensional objective system?. In this evaluation the value synthesis has been carried out according to scoring models. Lastly, the advantages and disadvantages of both production methods have been stated by analysing them according to related criteria. In the light of outputs gathered from the analyses, it has been determined that the shortwall mining method will out perform the longwall method. Keywords: continuous miner, shortwall mining, longwall mining, multi-dimensional objective system.

Jan 1, 2006