Search Documents

By J. A. Wates

Stope backfilling in South African gold mines uses the coarser cyclone fraction of the gold tailings. The disposal of the overflow from the cyclones, which is finer and of higher moisture content than normal gold tailings, presents some problems. This paper describes an investigation undertaken to define the parameters that are required for a quantitative and qualitative assessment of the operation and stability of slimes dams built of such material. However, seeing the investigation was conducted on the slimes from only one mine, it is recommended that, until a wider range of data becomes available, tests should be conducted for each individual mine.

Jan 1, 1988

By D. W. Boydell, E. B. Viljoen

A flowsheet incorporating rotary-drum filtration for the solid-liquid separation step, followed by solvent extraction for uranium purification, is used as a standard against which four flowsheets are compared. These flowsheets employ either counter current decantation or belt filtration for solid-liquid separation, and either solvent extraction or continuous ion exchange plus solvent extraction for the purification step. Sales revenue, taxation, capital expenditure, and operating costs are estimated. These factors are taken into account in the calculation of an incremental net present value for each circuit by the discounting of cash flows at 25 per cent per year over a projected life of 15 years. For the material used in these examples, the highest net present value results from the circuit that employs belt filtration followed by continuous ion exchange and solvent extraction.

Jan 1, 1978

By V. E. Ross

These effects were investigated in batch flotation studies, and by the measurement of rest and pulp potentials. At Iow additions of sulphurous acid as the pH regulator, flotation rate increased with increasing concentrations of dissolved oxygen. The recovery of chalcopyrite dropped significantly below a pH value of about 6,5 at 25 p.p.m. of dissolved oxygen, and below a pH value of about 6 at a dissolved-oxygen concentration of 8,2 p.p.m. The rest and pulp potentia Is measured indicated that dixanthogen is the dominant species formed on chalcopyrite surfaces during flotation with sodium ethyl xanthate. The results suggested that the same species might have formed on galena surfaces in the pulp after the ore had been milled in a ceramic mill under nitrogen. Increased additions of sulphurous, sulphuric, and hydrochloric acids increased the rest potentia Is, while the addition of sodium sulphite decreased these potentials.

Jan 1, 1985

William Schreiner Findlay (1908 to 1980) had a distinguished career in the mining industry, to which a mere account of his appointments does not do full justice. However, they give some idea of his ability as an engineer and a manager.

Jan 1, 1981

By G. T. Lineberry, C. M. Baird, D. L. Silverstein

The University of Kentucky (UK), with an enrollment of 25,891 in fall 2002, is a comprehensive, public land-grant university located in the Bluegrass Region of Central Kentucky. As the State’s flagship university, UK has long been involved in distance education, first through traditional correspondence courses, followed by use of videotape and satellite delivery in the 1970s and1980s, but soon supplanted by use of interactive television (ITV) and on-line course delivery in the 1990s to date. Today, UK Distance Learning Programs annually administers approximately600 course sections, with services provided to over 5200 enrollees. Courses are offered via six media: interactive video, Internet, on-site, satellite, open-air and cable television, and videotape, with hybrid delivery becoming increasingly popular. The University of Kentucky College of Engineering experience with distance instruction prior to 1985 was limited to videotape non-credit offerings. The Department of Mining Engineering, a small department in terms of numbers of both faculty and students, was a University pioneer in distance education. The first University degree program offered in its entirety by distance delivery(initially by itinerant faculty) was the Master of Mining Engineering. Satellite delivery from Lexington to Cumberland, Kentucky, was a welcomed change of delivery mode in 1987–88,resulting in six hours less travel time for faculty each week. Shortly thereafter, other initiatives directed toward fulfilment of its land-grant mission were undertaken by the College. Use of satellite for course delivery rapidly declined due to limited interactivity, in favour of compressed video and on-site instruction. Classroom sites in the Kentucky Tele-Linking Network (KTLN) now number over 200. The Network links schools, colleges and universities, as well as public and private agencies throughout the State. The KTLN supports voice, video, and data transmission in a uniformly-equipped environment. Beginning in the early 1990s, transfer-critical pre-engineering courses were delivered from Lexington to Kentucky’s community colleges with the largest pre-engineering enrolments. Success was limited, but lessons learned were invaluable. In 1996, the University of Kentucky College of Engineering was asked by the Kentucky Council on Higher Education (the predecessor to the Council on Postsecondary Education) to expand engineering education in Kentucky, first by initiating cooperative B.Sc. degree programmes in Chemical Engineering and Mechanical Engineering on the campus of Paducah Community College (PCC), located 400 km from the UK campus in Lexington. The third partner in these programmes is Murray State University (MuSU), a public regional comprehensive university 80 km south of Paducah. The genesis of the new degree programmes, which were subjected to ABET review in October 2002, as well as a summary of the major accomplishments and challenges of the innovative programmes, will be offered. The limited use of distance technologies for course delivery in these B.Sc. degree programmes will be discussed. A ‘no-spin’ overview of other non-traditional distance-learning ventures within the College of Engineering will be chronicled, with an honest assessment of the motivation for these efforts and, where appropriate, their relative degree of success. Among these ventures are: a BScME and a Master of Engineering programme at Toyota Motor Manufacturing of Kentucky, Georgetown, Kentucky; course exchange in Chemical Engineering between the University of Kentucky and the University of Louisville; an ITV-based Master of Engineering programme for practicing engineers in Kentucky; proposed joint-degree programmes in Civil Engineering and Mechanical Engineering with Western Kentucky University; and a proposed part-time MScME programme in Paducah, Kentucky, with a start date of August 2002, threshold enrolment permitting. Keywords: distance learning, distance education.

Jan 1, 2003

By I. E. Teymenson, N Fedunets

Mining-metallurgical complex is the base of any economics and influences directly on practically all branches of world economics. Therefore the task of estimation and selection of investment decisions in mining industry adequate to modern market conditions and the task of decreasing multidimensional alternatives selection uncertainty are very actual. An uncertainty of investment alternatives is explained by a number of reasons, main of which are a presence of several investors types, an unstable situation on the market and an absence of evident relations between appraisal criteria used. Maximum increasing of formalization and objectivity of information technologies applied for an estimation permits to reduce the uncertainty of investment variants estimation. A number of principled innovations, allowing to solve the task of decreasing of multidimensional alternatives selection uncertainty, are introduced into the information technology of estimating and selecting investment decisions in mining-metallurgical branch, developed by us. In the article the necessity of including a cognitive model into developed selection mechanism, which allows to take into consideration inter-influences of used critera, has been grounded. Besides, the forecasting model considering interconnected time rows has been applied for increasing the world conjuncture forecast quality. Further in the article main metrics types have been characterized and application of weighted Chebyshev’s metrics as the most compromised from all studied metrics for variants selecting has been proved, and also the developed procedure of directional search of effective compromise decisions has been described. Brief characteristic of designed instrumental means of multi-criteria variants estimation and selection finalizes the article. In conclusion expedience and efficiency of using the developed information technology for reduction of multidimensional alternatives selection uncertainty have been grounded.

Jan 1, 2003

Notices Competition for Student Members of the South African Institute of Mining and Metallurgy Each year the Institute offers a prize (or prizes should the entries warrant it) of up to Rl00 for the best paper or dissertation on a topic appropriate to the interests of the Institute. The competition is open to all Student Members of the Institute. NEW PUPLICATION Bougainville-the establishment of a copper mine. St. Kilda (Australia), 'Foundations', 1973. The editors of Foundations, Australia's journal of architecture, engineering, and construction, are preparing the above book for publication late in 1973. The story of Bougainville is told and illustrated NIM REPORTS Report No. 1503 Fast-neutron-activation analysis for the determination of oxygen m rock sam ples. Report No. 1514 The determination by X-ray-fluorescence spectrometry of minor amounts of niobium and tantalum in geological materials. Report No. 1530 AUREOL - an X-ray-absorption analyser for the determination of the uranium on loaded resin in ionexchange plants. Report No. 1534 The determination, by atomicabsorption spectrophotometry, of noble metals in the presence of sodium, barium, or sulphate ions. A comparison of uranium and lanthanum as 'releasing agents.

Jan 10, 1973

By K. I. Afewu, L. C. Woollacott

Little is reported in the literature that is directly useful for the interpolation film coefficients for the in-pulp adsorption circuits used in gold metallurgy. This can create a problem if the design or operation of these circuits is to be optimized by the use of simulation techniques. To address this problem, a study was undertaken on the influence of mixing intensity, scale, and geometry on the film coefficient in adsorption systems typical of the carbon-in pulp plants used for gold extraction. This, the first paper deals with the influence of these factors on the film coefficient and shows that the specific power to just disperse the carbon in the slurry is an important variable. This variable is also strongly dependent on mixing intensity, scale, and geometry-a dependence that is dealt with in the second paper in the series. From the informatlon obtained, practical scale-up procedures were developed. These procedures are considered to be applicable to resin-in-pulp as well as to carbon-In-pulp plants.

Jan 1, 1995

The first neutrinos in nature ever detected by man were "caught" in a unique laboratory some 3 km (over 2 miles) underground in one of the world's deepest mine shafts at East Rand Proprietary Mines (ERPM), Boksburg. Only 100 m from where gold is being mined from the rock face a small team of South African and American physicists work on one of the most fascinating and important fundamental research projects that is currently exciting the imagination of the scientific world. Neutrinos are sub-atomic particles just as are protons, neutrons and electrons, but they are unique in that they have neither electric charge nor mass. Cosmic neutrinos travel at the speed of light and penetrate stars and planets. Even a million kilometres of solid lead would not provide a satisfactory shield against them. Stars are believed to "burn" by means of nuclear reactions which produce enormous fluxes of neutrinos. The sun, for example, illuminates the earth with visible light, but also bathes it with neutrinos. After World War II, two American physicists, Profs Frederick Reines and Clyde Cowan, experimenting at a large nuclear reactor, succeeded in obtaining direct evidence of the existence of the laboratory-produced neutrino. It then became very important to establish whether neutrinos also existed in nature. This knowledge would lead to a greater understanding of the forces of nuclear physics, of the behaviour of nuclear particles and, indeed, is also relevant to astrophysics. From the start it was clear that the search for "natural" neutrinos would be difficult. Questions which arose were- * how could they be traced if they were without mass or electric charge? * how could other nuclear particles be screened off? * could these not be wrongly detected, or even prevent accurate detection of neutrinos? Neutrinos were known to be produced along with charged particles, by the reaction of primary cosmic rays with the constituents of the atmosphere. It was also known that when the neutrinos collided with matter, they themselves produced the same type of charged particle which could be detected if the unwanted charged particles from the atmosphere could be screened off. What was needed, therefore, was a laboratory where the particles produced in the atmosphere could be screened out, yet which would receive and detect the particles produced by the neutrons' collision with the matter (solid rock) in the vicinity of the laboratory. This meant that scientists either had to build a laboratory with an enormously thick lead shield for their detection work. . . or they could go as near as possible to the centre of the earth where only charged nuclear particles of the very highest energies could penetrate. ERPM was clearly the most suitable place in the world where so effective a "neutrino trap" could be set. Under more than 3 000 m of solid rock the apparatus for detecting neutrinos is well shielded against unwanted nuclear particles produced in the cosmic radiation which can reach the laboratory only in a steeply vertical trajectory. Other particles are easily stopped by the great thickness of rock. The air-conditioned laboratory is at one end of a 150 m long tunnel, 2,5 m high and wide, blasted from the rock. The electronic recording equipment is housed here, while the rest of the tunnel is filled with the detection system. When a charged particle passes through a detector element, it produces a minute flash of light which is recorded and which triggers a flash-tube array. This then defines the trajectory of the charged particle, which is also recorded on film for analysis. So far 82 neutrinos have been detected, 50 at the present level and 32 at a higher level, and the findings have borne out the physicists' theoretical expectations. In this joint project Profs Reines, J. P. F. Sellschop, Director of the Witwatersrand University's Nuclear Research Unit and M. F. Crouch of the Case-Western Reserve University of Ohio are the Chief Investigators. This unique endeavour has been made possible by financial support from the US Atomic Energy Commission, the University of the Witwatersrand and the Chamber of Mines of South Africa, as well as by the cooperation of the management and men of ERPM.

[Council for 1993/94 President Dr H. Scott-Russell President Elect J.A. Cruise Vice Presidents Senior D.A.J. Ross-Watt Junior P.D.K. Robinson Immediate Past President J.P. Hoffman Honorary Treasurer J.A. Cruise]

Jan 1, 1994

By M. H. Moys, K. S. Liddell

The dynamics of the ball load within a wet-grinding mil are examined, using measurements of torque and load position, The test equipment provided an accurate torque measurement, and the toe and shoulder positions of the load were measured by the use of a conductivity probe mounted in the mill shell. Both the variables tested-mil filing and rotational speed-influence the position of the load, and hence the torque, and have interactive effects on both the torque and the load position, An increase in mil speed and filing causes the torque to increase to a maximum value, after which further increases in speed or filing cause the torque to decrease. The position of the load toe is influenced only by the filing up to speeds of approximately 80 per cent of critical, whereas the speed and filing both cause the load shoulder to rise as their magnitudes are increased, The power drawn by the mill is predicted by the use of published equations, and these values are compared with the measured power draw.

Jan 1, 1988

By W. K. Brisden

The SAG Milling Seminar, which was held at Murdoch University in Perth on 30th November and 1st December, 1989, was a very successful technical seminar. Organizer Dr Norm Stockton reported a total attendance of 130, which was higher than the 70 expected: 20 delegates came from the eastern States and the remainder were from Western Australia.

Jan 1, 1990

By P. D. K. Robinson

In the second of a series of five colloquia with the theme Rescue 91 ..Survival Initiatives for the Mining Industry, the emphasis was placed on the harnessing of improved technology for the benefit of all the industry. The Colloquium was held at Mintek, Randburg, and attracted some 150 delegates and speakers from a cross-section of the industry. Eight papers were presented, and panel discussions were held to round off the morning and afternoon sessions. The purpose of the Colloquium was to allow mines and other groups to put forward innovative schemes in the management of technology that could be shared by everyone in their determination to ensure the survival of the gold-mining industry in the current difficult times. PAPERS The papers presented were as follows: The introduction of detachable bits at Cooke No. 1 Shaft, by C.A.F. Sweet of Randfontein Estates Survival through cost-saving measures in the engineering field, by E.J. Jurgensen of Freddies Survival through innovation, action, and a positive vision for the future, by G.C.V. Wade of Vaal Reefs Measuring misaligned guides, by H. Sperling of CSIR Rock-crushing innovations, by E. Trueman of Nordberg Improved explosives technology-has it been worth the effort? by RA. Lindsay of Sasol Cost savings through corrosion monitoring, by M. Tullmin of CSIR Enhanced efficiencies through technical developments in the survey departments, by D. Maree of Beatrix.

Jan 1, 1992

By R. J. Davidson, V. Veronsee

Some of the parameters affecting the elution of gold from freshly loaded activated carbon using pure water as an eluant were studied. The procedure involved pretreatment of the gold-loaded activated carbon with a strong reagent of sodium cyanide and sodium hydroxide, followed by elution of the gold with water. Gold-loaded carbon obtained from three different sources was studied. It was shown that the elution temperature was the most critical parameter, and column operation at I !OCC (gauge pressure of 50 to 100 kPa) is suggested. The effects of variations in the concentration of sodium cyanide required for the pretreatment of loaded carbon and of variations in elution flowrate were also investigated. Both these parameters were found to have only a marginal effect on the efficiency of gold elution. The investigation also indicated that gold-elution rates were affected to a considerable degree by the particle size of the carbon concerned. Higher elution flowrates could be used when carbons of finer particle size were eluted. A modified eluate-collection procedure was also developed during the course of the investigation. Oven-drying of the loaded carbon was shown to have little or no effect on the efficiency of the subsequent gold elution. The calcium and silica contents of the various carbon samples were also determined. It was immediately evident that the calcium content was very considerable in the case of loaded carbons originating from carbon-in-pulp operations. Calcium concentration was particularly high where air agitation had been employed in the carbon-contacting circuit. To some degree, the calcium build-up explains the serious carbon fouling taking place, resulting in a decreased efficiency of gold adsorption. The fouling problem was found to be less severe when mechanical agitation was used. No poisoning by calcium carbonate was observed where the pregnant solution had been acidified before it was contacted with the carbon.

Jan 1, 1979

By W. P. Channon, J. B. See

The reduction of fluxed and non-fluxed manganese, ores by ferromanganese silicide by W. P. CHANNON, B.Se. (Eng.), M.Sce. (Eng.) Wits. (Visitor) and J. B. SEE, B.Sce. Hons., Ph.D. (New South Wales), M.I.M., M.I.M.M. (Member) In South Africa, medium-carbonferromanganese is produced by the silicothermic reduction of slags containing MnO. Because of its importance in the production of refined ferromanganese, a study was made of the reaction between a premelted South African Mamatwan manganese ore and various ferromanganese silicide reducing alloys, with and without fluxing agents. Because the reaction is highly exothermic, temperature appeared to have little effect on the rates of manganese transfer to the metal and silicon transfer to the slag, and an apparent equilibrium was rapidly approached. Limits were determined for the favourable effects of fluxing additions, and manganese recoveries were found to decline as the ratio of CaO to MgO decreased as a result of the addition of basic flux. The recovery of manganese passed through a maximum, and subsequently decreased for variations in the ratio of alloy to ore. The results obtained, when used in conjunction with other physicochemical data related to this slag-metal system, suggest optimum slag compositions for the efficient manufacture of medium-carbon ferromanganese from Mamatwan ore.

Jan 3, 1977

By N. A. Barcza

An investigation was conducted into the reactions between the slag system MnO-CaO-MgO-SiO2(AI2O3) and the alloy system Mn-Fe-Si-(C). Synthetic slags representative of plant melts and a plant alloy were reacted in alumina crucibles at temperatures of 1400°C, 1450°C, 1550°C, and 1600°C. In similar experiments, slags were used that comprised a South African manganese ore with various amounts of lime and several synthetic alloys with various silicon contents and manganese-to-iron ratios. These experiments were conducted in a vertical molybdenum-wound resistance furnace with full temperature control. Slag-to-alloy ratios were also varied during the tests. The rate of reduction of Mn.O3 and the MnO from the slag by the silicon in the alloy was extremely rapid, most of the reaction being completed within five minutes. The strongly exothermic nature of the reaction resulted in considerable generation of heat at the slag-alloy interface, causing convectional stirring of the contents of the crucible and promoting the rate of reaction. Equilibrium was usually attained after fifteen minutes. The major limitation governing the recovery of manganese is the need for the silicon content of the alloy to meet a maximum specification of 2 per cent. Higher concentrations of silicon in the final alloy of between 8 and 12 per cent favour good recoveries of manganese from the slag, but, since such an alloy is not salable, lower recoveries must apparently be tolerated. In alloys of 2 per cent silicon, low activities of the silicon are responsible for poor recoveries of manganese. The activity of MnO in the slag can be increased by moderate additions of CaO and small amounts of MgO, i.e., by an increase in the basicity of the slag.

Jan 1, 1979

By M. R. Grant, G. S. Kruger, H. D. van der Merwe, T. N. Huffman

Sixteenth to seventeenth century Kalanga miners dug a series of sub-vertical shafts into a 10 to 30 m wide zone of copper ore at the Thakadu Mine near Matsitama, Botswana. They went down at least 6 m in search of thick malachite veins. The host rock was hand 'cobbed' to remove the veins, which were then smelted nearby in small bowl furnaces. Evidently, the furnaces lacked clay superstructures, since a simple pit was sufficient to smelt the almost pure malachite. The copper bloom was probably refined in villages further away.

Jan 1, 1995

By A. Koursaris, J. B. See

The influence of Iscor coke and Delmas coal on the reduction of Mamatwan manganese ore to ferromanganese was examined by use of a variation of the 'stationary charge in controlled environment' (SCICE) technique. The charges of Mamatwan ore and the appropriate reducing agent were heated to temperatures between 1300 and I600 °C and either allowed to cool immediately the required temperature had been reached or held at that particular temperature for periods of up to ... hours. The heating rate was 350°C per hour, the particle size of the ore was between 2,83 and 12,7 mm, and the particle size of the reducing agent was between 2,83 and 6,35 mm. After being allowed to cool in air, the reacted charges were examined by optical microscopy, X-ray-diffraction analysis, scanning electron microscopy, and electron-microprobe analysis. No significant difference was found between the changes observed during the reduction of Mamatwan manganese ore by Iscor coke and by Delmas coal. A hypothesis is advanced to explain the mechanism of formation of the Fe-Mn-C alloy.

Jan 1, 1979

By C. Ringas, F. P. A. Robinson

Various theories proposed to account for microbial corrosion are reviewed as a background to a better understanding of this type of corrosion in iron-based alloys. Experimental evidence is presented to show that even stainless-steel alloys are prone to microbial attack by sulphate-reducing bacteria. The corrosive attack by the bacteria is due primarily to the hydrogen sulphide that is produced as part of their metabolic processes.

Jan 1, 1987

By M. E. E. Douglas, A. K. Haines, D. I. Nicol, C. M. Olëm, W. M. Craig, G. D. Louw

A description is given of the design of the continuous ion-exchange demonstration plant at Blyvooruitzicht Gold Mine, including details of the process design, the column construction, and the control system. The operating and process results gathered over a period of seventeen months are summarized, and development work and modifications to the process are discussed. It is concluded that the system comprising continuous loading and continuous elution is technically feasible and can be scaled up with confidence.

Jan 1, 1978