Search Documents

Council for 1995/96 President D.A. J. Ross-Watt President Elect Dr N.A. Barcza Vice Presidents Senior R.P. Mohring Immediate Past President J.A. Cruise Junior J.R. Dixon Honorary Treasurer J.A. Cruise

Jan 1, 1996

By J. J. Van Rensburg

The commissioning of a test facility for the calibration of anemometers by J. J. VAN RENSBURG (Student Member). After the erection of a commercially produced open-jet wind tunnel for the calibration of the anemometers used in mine ventilation, the wind tunnel was calibrated for routine use. There is a choice of five orifice plates. which, together with a variable-speed fan, can give a measurable range of air velocities in the test section from about 0,05 to 35 m/so The orifice plates were calibrated against a standard pitot tube, and it is now necessary only to measure the pressure drop across an orifice plate and to read off, from a set of graphs, the true outlet velocity in the test section. The paper describes the underlying theory and the test results.

Jan 4, 1975

A description is given of a simple, cheap device that enables the intact shear strength of rock to be determined quickly and inexpensively. Thin rock plates, prepared with a diamond saw, are tested in double shear by a linear punching action. By varying the direction of the diamond-saw cut in a number of specimens, the change in shear strength can be measured for different orientations relative to the rock fabric.

Jan 1, 1980

By R. P. King

The flotation behaviour of phoscorite from the Phosphate Development Corporation was measured in a pilot plant, the flotation cells in the plant being varied in configuration so as to operate with or without circulating loads. The ore was floated in a batch cell so that the parameters for a kinetic model could be estimated, and these parameters were then used in a flotation-plant simulator, which is based on the kinetic model, in the prediction of the performance of a pilot flotation plant operating on phoscorite. The simulator predictions compare well with the measured performance of the ore in the pilot plant, but the comparison shows that the kinetic model is not completely adequate for the prediction of performance in continuous flotation plants. The model is weakest in its ability to model the behaviour of the froth phase. The flotation behaviour of the ore could be adequately described when it was assumed that the apatite and gangue each consist of floatable and unfloatable components. The effect of particle size on the specific flotation-rate constant of apatite was found to have a maximum at 85 µm and to fall to zero at 400 µm that for the gangue had a maximum at 50 µm and was zero at 350 µm.

Jan 1, 1978

By L. W. Helle

In this investigation, which was conducted at the Metallurgical Research Plant, Lulea, Sweden, a series of experiments were carried out using a water-model to simulate the gas rinsing of a ladle containing liquid metal. The factors examined include the effect of gas flowrate, the position of a porous plug or lance, the immersion depth of the lance, and the geometry of the bath at the time of complete mixing. Mixing times were recorded by conductivity measurements. The results showed that there is a threshold level for mixing above which no advantage is to be gained from an increase in the gas flowrate. It is suggested that the results can be applied to rinsing ladles in working situations, the levels being approximately 270 dm3/min for 40 t ladles and 780 dm3/min for 150 t heats. The optimum siting of the lance or porous plug is a position that is three-quarters of the internal radius from the centre of the ladle with the lance penetrating as deeply as possible into the ladle. The best design of liquid bath is that having a diameter-to-height ratio of I. An equation was developed for the calculation, by dimensional analysis, of the time required for mixing during gas rinsing, and a comparison of the calculated mixing times with the results from production trials shows a satisfactory agreement (with a correlation factor of 0,91). Thus, an equation is available for the calculation of the stirring time needed to completely mix the bath in production situations.

Jan 1, 1981

By K. Hodgson, J. P. M. Hojem, N. G. W. Cook

Already about one-third of South Africa's coal is mined at depths exceeding 100 metres. Almost all this mining is done by the bord and pillar method. Conventional design procedures call for ever larger pillars as depths of workings increase, resulting in the loss of large amounts of coal and reductions in productivity. Barrier pillars are in general use to ensure against large collapses. The presence of these strong pillars would allow a more efficient design of the bord and pillar layout to yield improved extraction ratios by using smaller, yielding, pillars between the bords. Knowledge of the complete load- displacement curves for such pillars is a prerequisite for the design of such a system. A 100-MN, stiff jacking system for measuring the complete load-displacement curves of pillars with cross-sections of up to 2 m X 2 m is described. The jacks are installed in a slot cut across the central plane of symmetry of a pillar, thereby ensuring that the stress distribution in the pillar during a test, especially at its contacts with the roof and floor, is identical to that caused in a similar pillar by convergence across the seam. Preliminary results in the form of complete load-displacement curves for test pillars of about 1.5 metre square section are given.

By D. F. Howarth, F. F. Roxborough

Some important aspects of the design of rock-cutting systems remain relatively unexplored. Two areas of practical significance in this context form the subject of this paper: cutting in jointed or fissured rock, and groove-deepening. A series of controlled laboratory experiments on the performance of disc cutters in jointed rock showed that the spatial and geometrical configuration of jointed rock masses needs to be taken into consideration in the design of mechanized rock excavating systems. One series of experiments showed that, under favourable geometric conditions, the energy required to cut in a jointed rock mass is at least half that required to cut otherwise intact rock. Groove-deepening-the progressive deepening of a groove by successive passes of a cutter-is a potential operational feature with most mechanized rock-excavating systems. Laboratory experiments revealed an important fundamental cycle of events associated with disc cutters when progressively deepening a groove in intact rock. Furthermore, in contrast to pick cutting, groove-deepening by discs is shown to be an efficient operation and one that should not necessarily be avoided. This can be directly attributed to increased interaction between the disc cutters as the result of an increase in magnitude of the lateral forces generated as a groove is deepened.

Jan 1, 1982

By A. A. Bradley, K. H. Stanton, P. J. D. Lloyd

A theory for the dynamic balancing of centrifugal mills is presented that takes account of the mass and shape of the charge in a gyrated grinding tube and the way in which the charge lags behind the centrifugal force vector. predicts that a corresponding lag in the angular position of the counterweight centres of mass is necessary, and that the fractional filling should be increased if the ratio of gyration diameter to tube diameter is decreased. A worked example is given for a I MW centrifugal mill that was balanced adequately by the methods described.

Jan 1, 1983

By J. Levin

The Bond standard grindability test provides a Work Index that is widely used to estimate the energy required for grinding, but the test cannot be applied to fine materials such as plant tailings and middlings. For such materials, a comparative grinding test must be used in which a reference material from an operating plant is ground in a laboratory mill to determine the 'equivalent' energy consumption per revolution of the laboratory mill. As the Bond grindability test mill and its operating conditions are specified, its equivalent energy consumption per revolution should be a constant, here designated as B. Once B has been determined, the mill can be used to estimate the grindability of fine materials without the need for reference materials. A value of B can be calculated from any Bond grindability test, and 245 tests that were conducted at Mintek were examined to determine its value. A wide range of values was found, but most of them were grouped around 198 x 10- 7 kWh/rev, which is taken as the best estimate of B that is available at present. Values of B that are not close to this figure are obtained from materials for which the Bond grindability test gives misleading or 'spurious' Work Indexes. These spurious Work Indexes lead to the apparent departure of B from its true value. Some limitations of the Bond grindability test arise from its use of a mill without litters and of screening, instead of classification, to close the circuit.

Jan 1, 1989

Contribution by F.S.A. de Frey The authors are to be congratulated on a job well done by making, in their paper, such a pool of information available to mining engineers. I would like to comment on the following statement: 'As an alternative to the commonly used deep-level mining methods, consideration should also be given to pillar mining at great depths as a logical extension of the current methods. For example, a 75 per cent extraction Or Ryder's discussion The moderate levels if average pillar stress (APS) (320 MPa) are consistent with pillar stability. Squat 10:1 pillars should never 'fail' in themselves, and foundation strengths are also not exceeded (the stresses are well below the 2 ½ x UCS rule-of-thumb provided the foundations comprise normal strong 200 MPa quartzites). Authors' reply We thank Dr de Frey for his contribution to our paper on shallow hard-rock pillar systems. To considerable extent, we share his enthusiasm the potential role of squat pillars in deep-level mining, although we harbour reservations concerning strata control, mining economics, other issues. We agree wholeheartedly that further research, together with carefully planned field trials, is warranted in pursuit of this potentially highly rewarding concept. .

Jan 1, 1995

Contribution by W.D. Ortlepp? The authors are to be commended for publishing their interesting view of an aspect of deep-level mining technology that is becoming increasingly topical and vitally important. This is the second paper in the journal within four months to deal with the crucial needs of highly stressed tunnel construction, the other being the paper on the design and testing of rockburst support in the February 1994 issue. Both papers re-examine important innovative ideas that are more than a quarter of a century old, but that have not yet been implemented by the industry. It is to be hoped that they will now, taken together, serve as a new starting point for a definitive examination of what constitutes proper tunnel-support design. There can be no question that the need to develop a design approach that will solve the problems of tunnelling at depths of 4000 m or more has now become crucial. Contribution by A.M.J. Vervoort* Although the overall paper is very interesting and the future research (comparison between numerical simulations and underground measurements) will be very challenging, I would like to make some remarks regarding the set-up of the numerical model and the interpretation of the elastic results.

Jan 1, 1995

By J. D. Koch

A 'project' is defined here as a process in which an idea is developed from its inception until either it is discarded or the product of the idea has been accepted by the ultimate user. The phases in a project, particularly the early phases, are examined, and project organization is described and contrasted with a functional line-management type of organization. Emphasis is placed on comprehensive definition, which is vitally important to the achievement of the goals of time, cost, and quality set for a project.

Jan 1, 1981

By M. Splaine, W. Davidson, D. C. Atkinson

Since 1964, Nchanga Consolidated Copper Mines, Ltd., has been developing and using production scheduling methods for optimizing its metallurgical operations in the short term (up to one year). Medium-range metallurgical planning has been possible only by successive evaluations of a single-year LP. A modified version of Rosenbrock's direct search technique has now been developed to allow multi-year optimization of both mining and metallurgy for medium-range planning. The modifications to the search technique have produced a marked increase in computational efficiency for this heavily constrained problem in many variables and the system is a usable planning tool, given a reasonably powerful computer. The plans are 'optimum' in the sense that they yield the maximum present value of the operations. Each of the resulting five-yearly mine plans forms the basis for further detailed metallurgical evaluation by the established production scheduling system.

Now a new generation of computerized drill rigs has been launched and they are based on modern standard PC-computer technology. The rigs have been well embraced by the market and more than 100 units have left the assembly line. The new generation has taken a quantum leap forward with respect to drilling accuracy, logging capabilities, reduction of manpower in some types and serviceability compared to the previous generation of drill rigs. The Can bus technology, well proven in the automobile products, is the backbone in the new generation control system of Atlas Copco. The short-term development is now focused on establishing this new automation platform on other product lines of Atlas Copco products. The long-term objectives is to offer the mining industry Atlas Copco products with one common automation platform. Essential for Atlas Copcois to contribute to the work with the on-going Data Exchange standard between mining machines and mining computer systems (IREDES). Our belief is that an accepted standard will make mine automation programs affordable for a wider base of the mining industry, because of the possibilities to a cost effective integration of different equipment with a minimum of system integration problems and machine specific interfaces.

Sep 1, 2001

By P. Wiesner, H. –M. Stonner

A brief account is given of the influence of sulphuric acid and chloride ions during the recovery of uranium by solvent extraction, followed by a discussion of the settling behaviour of dispersions and models to represent that behaviour. The paper ends with a description of various methods for the recovery of solvent, which is lost in the solvent-extraction process by entrainment and adsorption on solids and by dissolution.

Jan 1, 1982

By K. R. Vost

Variation in air temperature in a cross-section of an underground airway by K. R. VOST, B.Sc. (Glas.), M.Sc. (N.S.W.) (Visitor) Measurements of air temperatures in underground airways are normally made at only one point in a cross-section, and the air tem peratures at other points in the cross-section are assumed not to differ significantly from this. This paper discusses measurements made at a number of points in fifty crosssections in airways with different air velocities and wetness of floor. These measurements show that significant variations of air temperature can occur in a given cross-section at a given time. The effects of such variations on the accuracy of measurement of rises in air temperature as air passes along an airway are discussed. The importance of considering experimental error in the measured rises in air temperature when attempting to validate theoretical and empirical methods of predicting such rises is also discussed.

Jan 7, 1976

By RT White

For a number of years the steel tube and pipe industry has worked on resolving problems of product quality. These have largely been resolved and new products have been developed to take advantage of new developments. To fully coordinate market acceptance guidance on use of galvanized piping was also required. This was largely achieved locally in 2004 with the publication by the SABS of ARP 060 - Guidance on the use and application of hot dip galvanized steel piping for the transportation of potable water in South Africa. Use of this document is not easy however and a need to have a simple computer model to assist the specifier was identified. Working with a major tube and pipe manufacturer this is now being developed and this paper will provide the background to the model?s development and its intended use. There is still a need for a partner Code of Practice on the performance of galvanized piping in buried conditions and the need for this will be highlighted together with current available information.

Jan 1, 2006

The 90th Annual General Meeting of The South African Institute of Mining and Metallurgy was held at Kelvin House, Johannesburg, on 19th August, 1987. Dr H. Wagner (President) was in the Chair and declared the meeting open at 16h00. Obituaries The President read out the names of the departed Members as follows: N.M. Airey, F.J. Kisbey-Green, Dr R.A. Pelletier, C.B. Anderson, A.R. Cator, J. van Heerden, P.J. Burman, C.C. Crosson, M. Livingstone¬Blevins, S.T. Firman, V.E. Kisbey-Green, and A.L. Corna. All stood and observed a moment of silence as a mark of respect. Minutes The minutes of the 89th Meeting of the SAIMM, which was held on 20th of August, 1986, were confirmed.

Jan 1, 1987

By J P. van Dyk

The dramatic strengthening of the rand against the dollar as well as a decline in quantity and quality of locally available concentrates have had a dramatic impact on Zincor?s operations during the previous two years. Zincor has responded with the implementation of a number of technical improvements to the process to decrease cost and increase revenue and plant flexibility. Among the initiatives is the pre-leaching and pelletising of the zinc concentrate, de-bottlenecking and process improvements in the leach and purification circuits, the introduction of cathode washing and automated cathode stacking in the cell house and the installation of a new furnace to produce pre-alloyed jumbos. This paper will describe these initiatives and others that Zincor have recently taken to stay competitive in changing global base metals market.

Jan 1, 2005

By J. Levin, I. J. Corrans

Wet high-intensity magnetic separation (WHIMS) for the concentration of gold and uranium was tested on many Witwatersrand cyanidation residues, and on some ores and flotation tailings. The results varied, but many indicated recoveries of over 60 per cent of the gold and uranium. The main source of loss is the inefficiency of WHIMS for material of smaller particle size than 20fLm. The recoveries in the continuous tests were lower than those in the batch tests. The continuous tests indicated an operational difficulty that could be experienced in practice, namely the tendency for wood chips and ferromagnetic particles to block the matrix of the separator. It was decided that a solution to the problem lies in the modification of the separator to allow continuous removal of the matrix for cleaning. A system has been developed for this purpose and is being demonstrated on a pilot-plant scale. Promising results were obtained in tests on a process that combines a coarse grind, gravity concentration, and WHIMS. In the gravity-concentration step, considerable recoveries, generally over SO per cent, of high-grade pyrite. were obtained, together with high recoveries of gold and moderate, but possibly important, recoveries of uranium. A simple model describing the operation of the WHIMS machine in terms of the operating parameters is described. This should reduce the amount of empirical test work required for the optimization of operating conditions and should provide a basis for scale-up calculations. The economics of the WHIMS process is discussed.

Jan 1, 1979