Search Documents

Toxic gases, mostly carbon monoxide (CO) and nitrous oxides (NOx), are invariably generated by commercial explosives under practical conditions of usage because of oxygen unbalance and non-ideal chemical reaction. Permitted explosives are statutorily required to meet the criteria stipulated by regulatory authority for their toxic fume quality for their safe use in underground coalmines. Solid blasting using P5 explosives contribute around 60% production from Indian underground coal mines. Low pull and yield per blast in solid blasting has been identified as a reason for low production and productivity of Indian underground coal mines. In an effort to improve performance of solid blasting, it was envisaged to apply air decking between suitable P5 explosives using high density polyethylene (HDPE) spacers under a Ministry of Coal, Government of India funded project. A non-deflagrating slurry explosive composition having high air gap sensitivity was specially developed for this purpose, so that air decked cartridges get detonated sympathetically with single priming. However, statutory authority in India apprehended that the use of oxygen negative HDPE spacers can influence the generation of toxic gases. The effect of using HDPE spacers on the generation of toxic gases was studied under simulated laboratory conditions with newly developed as well as with three commercial P5 explosives. The results of studies presented in this paper revealed that the level of carbon monoxide increases linearly and there is no significant effect on the level of oxides of nitrogen due to the use of HDPE spacers with selected explosives. Studies also revealed that this newly developed slurry explosive can be used for air decking up to 15 cm using HDPE spacers of weight not more than 21 g without exceeding the permissible limits for toxic gases.

Jan 1, 2008

Grains are subject to contamination by mycotoxins which are metabolic by-products of various fungi. The fungal infestations produce local concentrations of the mycotoxins thousands of times higher than the average. These facts make the sampling of the grain for assessment of the mean mycotoxin levels potentially very difficult. In the context of sampling theory, this morphology of the infestations creates a very high distributional and intrinsic heterogeneity of the grain shipment. The distributions of mycotoxin concentrations in seaborne shipments that exist at loading and the number and intensity of infestations that develop under shipping conditions are unknown. All grain shipments carry spores that may give rise to mycotoxin-producing colonies; moisture and temperature determine the final extent of the problem. This paper develops the value of the sampling constant with respect to intrinsic heterogeneity based on data on observed Ochratoxin A (OTA) concentrations in individual wheat kernels. A useful relationship between the distribution of mycotoxin concentrations on a kernel to kernel basis and the distribution of concentration over subsamples is developed.

Jan 1, 2009

By J. B. A. Solar Menéndez, M. A. Martínez Fidalgo, L. A. Alvarez-Santullano

1. ANTECEDENTS This present communication refers to the results of the research project entitled "Training in the correct use of chemical oxygen self rescue apparatus and also an analysis of apparatus autonomy", carried out under the auspices of the Specific Collaboration Agreement signed between the Industry Council of the Principality of Asturias (Spain) and INSALUD (National Silicosis Institute, Spain). The antecedents of this project lie in work undertaken by the National Silicosis Institute aimed at optimising efficiency in the use of chemical oxygen self rescuers through improvements in worker training. To be precise, by means of Agreements drawn up between the above-mentioned parties, a simulator was designed and incorporated as the basis of a training station within the " Fundación Barredo" of the Industry Council of the Principality of Asturias. This has been operative since the year 2001 and, up to the present, 2300 Asturian coal mine workers have been trained there. What prompted this activity was the observation of various errors in the use of the self rescuers, deriving from their innate characteristics, especially with respect to the sensation of discomfort - the high temperature and humidity of the breathed oxygen, resistance and inconvenience - and limited autonomy. It was precisely this insight that, in critical situations, lack of familiarity with the conditions of discomfort likely to be experienced during the evacuation process might lead to rejection of the equipment, with fatal consequences, that has justified the setting up of this training and simulation centre. The centre is able to provide all mine workers with the necessary training, and experience of the characteristic sensations experienced when using such equipment (Fig.. 1).

Jan 1, 2003

By C. -J. Rick

The ferroalloy market is characterized by a very long communication distance between the consumer and the producer. This has created a situation where it has been difficult to change ferroalloy properties. In this paper different FeNi and FeCr-compositions are discussed and their merits for stainless steel-makers in different situations are compared using the process models applied at Outokumpus Avesta works and Acerinox's Columbus operation Keywords Ferroalloy design, ferrochrome, ferronickel, stainless steel making, UTCAS software.

Jan 1, 2010

By L. Gunnewiek

An advanced real-time monitoring system called the tapblock diagnostic system (TDS) has been developed. The purpose of the TDS is to help furnace operators manage the safe operation and economical maintenance of furnace tapblocks. This system is an evolution of the current practice of using historical records and operator interpretation to assess the ?health? of a tapblock. The main parameters affecting tapblock health are heat removal capacity and refractory wear, and these are currently difficult to assess in situ except in a global way. By using monitored and operating data together with predictive numerical modelling and multivariate statistical methods, real-time tapblock performance is assessed relative to expected performance. A state indicator in the form of a green, yellow, and red light is used by furnace operators to monitor the tapblock performance and health status during operation. Access to historical operating data and the provision of diagnostic functions allow for probable health degradation events to be deeply investigated. A recent opportunity to evaluate the actual performance of a first generation TDS installed in the KIVCET furnace at Teck Cominco?s Trail Operations showed that a reasonable estimate of tapblock health was made. However, the evaluation also found that some areas of refractory wear were missed, and a new mechanism affecting refractory wear was discovered that was not previously known. This has reinforced the belief that there is a need to develop improved methods of monitoring so that data used to define the health of the tapblock is more comprehensive and accurate.

Jan 1, 2008

By C. D. Winkler

Vanadium-based sulphuric acid catalyst has been utilized to oxidize SO2 to SO3 since the early 1900s. This versatile product displaced the expensive and easily poisoned platinum-based catalyst in nearly all applications by the 1930s. MECS has been manufacturing the vanadium-based catalyst since 1925 and today is the leading supplier in the world of sulphuric acid catalysts in a variety of forms. Currently, MECS has worldwide customer/technical support for the catalyst as well as a dedicated catalyst manufacturing plant in Martinez, California. MECS also has a strong technical and research and development programme dedicated to creating new and improved products and services. This paper will describe some of the technical details of vanadium-based sulphuric acid catalysts as well as offering a unique look into how caesium-promoted MECS catalysts can be used in single and double absorption acid plants, and off-gas plants running on irregular gas feeds, to reduce emissions and preheater run times. An update on MECS technical services extended for use in characterizing converter performance is also presented.

Jan 1, 2009

By S. Schmachtel

Several possible physico-chemical properties of composite electrodes for oxygen evolution are presented to describe experimental data for which a mathematical model had been developed. On this basis, local electrical and electrochemical properties of a composite electrode were investigated with conductive atomic force microscopy (CAFM) and scanning electrochemical microscopy (SECM). It could be shown by CAFM measurement that the boundary between matrix and catalyst particles seemed to have special advantageous electrical properties. The SECM measurements showed the presence of mass transport phenomena with increased surface concentrations, whilst the thickness of the Nernst diffusion layer was very small. An intermediate was detected and assigned to be hydrogen peroxide. From all species involved in the oxygen evolution reaction (H2O2, H+ and O2), it was concluded that local active spots exist on the electrode on which hydrogen peroxide reacts to oxygen and protons. A two?step two-material process was suggested to explain the whole oxygen evolution mechanism.

Jan 1, 2008

By Kedikilwe Oageng

Effective perimeter control during drilling and blasting is critical not only to blasting results but also to the overall stability of the pit over its entire life span. A pit where perimeter control is not given enough attention when conducting drilling and blasting operations, often experiences over-break or back break beyond final pit wall limits, and therefore has a relatively high probability of failure. Such a pit also becomes unsafe, sometimes not easily accessible, has increased loading costs due to production of oversize, longer cycle times and often problems are encountered when blasting subsequent benches. All these are undesirable consequences, which have negative cost implications. Specialised blasting techniques such as trim blasting and pre-splitting have over the years proved to be effective perimeter control measures. However, the success of these techniques is directly attributable to the time and effort given to the processes. This paper presents results of a project undertaken to monitor, review and optimize the trim blasting and pre-splitting processes at Orapa Diamond Mine in Botswana. The project was specifically incepted to improve the final wall conditions, which continued to deteriorate due to persistent over-break during blasting. The paper also analyses the results obtained against a benchmark of results taken prior to project implementation. Specific blast design parameters which are critical to blasting results were identified as problem areas after auditing of the pre-implementation drilling and blasting practices. These include drill-hole depth, spacing, splitting factor for pre-splits and timing of trim blasts. The impact of different rock types on the results was also studied, and recommendations were made at different phases of the project and results obtained after implementation analysed until optimum results were achieved.

Jan 1, 2008

By B. Geelhoed

Gy's formula for the variance of the fundamental sampling error (FSE) is based on a model that assumes independent selections of particles. A generalization of this model, which can theoretically lead to more realistic representation of actual sampling processes, was, for the first time, experimentally verified by repeated sampling from a well-mixed batch consisting of particles of zirconium silicate of two different sizes. The predictions for the sampling variance made in Gy?s theory and in the more general model were compared with the experimentally observed sampling variance. During the experiment performed here, the variance prediction made in the theory of Gy ranges from 0.96 × 10?7(g2/g2) to 0.95 × 10?7(g2/g2), which is approximately a factor 60 lower than the experimentally observed variance (5.76 × 10?6(g2/g2)). The difference between the Gy prediction and the experimentally observed variance cannot be fully explained by the uncertainty in the experimentally obtained variance due to the finite number of degrees of freedom. Therefore, the difference is likely to be a significant effect. This shows that, under the experimental conditions, Gy?s formula for the variance of the FSE probably undervalues the sampling variance, unless an empirical correction factor for grouping and segregation is applied in the theory of Gy. The new theory resulted in a variance prediction of 6.00 × 10?6(g2/g2), which is much closer to the observed variance than the Gy prediction. This indicates that the generalization of Gy?s theory offers an outlook for providing a better variance prediction than the Gy predictor in the case of dependencies between particle selections. The results are discussed. Keywords: sampling, variance, parameter for the dependent selection of particles, Gy, experiment.

Jan 1, 2009

By J. Danoczi

South Africa is running out of fresh water and is looking at ways to improve water usage. This report addresses how a diamond mine in Gauteng has improved the utilization of its water resources. In the past, water from the local river was deemed the most suitable to use in the grease recovery plant but subsequent tests on the water from the slimes dam have shows that this water source is in fact more suitable for diamond recovery. Utilizing the slimes dam water provides a more stable water source than the local river while also reducing the impact of the mine on the water resources in the area.

Jan 1, 2008

By F. P. Greyling

The aspect of sustainability of ferroalloy processes has long been a serious matter for consideration in many of the world?s industrialized countries. A number of countries can be named where ferroalloy plants that were once flourishing, have all but disappeared. One of the most important factors playing a role in this type of occurrence is the cost and availability of quality raw materials. Given that all natural resources will be depleted with time, users are compelled to develop new processes that are sustainable in the changing environment. The DC arc smelting furnace is one such process that has proved itself, and has gained increasing popularity over the past two decades. This process, amongst other benefits, directly addresses the use of more readily available and more affordable raw materials in ferroalloy production. Since early in the new millennium, GLPS has been involved in various studies for different clients of furnaces for the production of ferroalloys. Two of these recent studies have culminated in the design, construction and commissioning of DC arc furnaces for the production of ferrochrome. One of these furnaces is a 10 MW unit at Mogale Alloys, and the other a 60 MW unit at the Middelburg plant of Samancor Chrome. This paper discusses the approach taken in the design and construction of these two furnaces, which, although varying significantly in size and capacity, are very similar in many other aspects of their design. Keywords Furnace, DC arc, and ferrochrome.

Jan 1, 2010

By E. Keskinkilic

In this study, sulfide-type inclusion morphologies of a Ca-treated hot-rolled wheel steel, Grade-X, were investigated. The specimens taken from the hot-rolled products of Grade-X heats were studied. The size and distribution of elongated sulfide inclusions were examined for the heats of different S levels. Elongated sulfide inclusions were either not observed or rarely encountered when ladle analysis S content was below 50 ppm. The size and relative abundance of sulfide inclusions were reported to increase markedly when the S composition was greater than or equal to 70 ppm and the Ca/S ratio was less than 0.50. The effect of Ti addition (0.010?0.020% Ti) on sulfide-type inclusion morphologies was then investigated for heats having a sulfur content higher than 50 ppm. Addition of Ti was found to have a partial effect on decreasing the size of sulfide-type inclusions under real steelmaking conditions. Keywords Sulfide inclusions, Ca-treatment, titanium.

Jan 1, 2011

By N. C. Gay

The quantitative evaluation of the performance of fill materials placed in gold mine stopes is achieved by (i) measurement of the in-situ load- displacement, or stress-strain, characteristics of the materials; (ii) an objective comparison between the observed fill performance and that predicted from suitable computer modelling techniques; and (iii) objectively comparing conditions in backfilled and conventional stopes. Considerable problems have been experienced with the development of sufficiently robust instrumentation which can be installed within filled pad- docks and give reliable information over a long period of time. However, at most mines where backfill performance is being monitored, it has been possible to correlate stress measurements within the filled paddocks with strain measurements adjacent to the paddocks. The resultant stress-strain curves agree relatively well with those determined in the laboratory. Measurements in the hangingwall strata of filled and unfilled stopes indicate that the placement of fill does reduce the amount of inelastic convergence due to bed separation. Moreover, in some stopes, the rate of convergence with respect to face advance does reduce to that of the theoretical elastic convergence. Quantification of changes in the conditions at the stope face due to placement of fill has proved difficult. Observations indicate that, provided the fill is placed close to the face (- 5 m), and adequate temporary face support is used, conditions in filled panels are superior. In addition, in filled panels the damage caused by a rockburst in the stope and, particularly, in gullies is generally much less than would be expected in an unfilled stope. To quantify these improvements, parameters such as stope height, face advance and the frequency of falls of ground are being monitored.

Jan 1, 1988

The Barrick North Mara Mine and the Advanced Systems Group at SGS Minerals collaborated on the implementation of a grinding expert system for the control and optimisation of a single semi autogenous (SAG) mill. Over the last 5 years, grinding expert control has gained wide acceptance by mineral processors. In this paper, two key factors for success are highlighted: the adaptability of the software tools and the interaction with site personnel. Created with SGS?s MET expert console (MEC) toolkit, and running on Gensym?s G2 real time inference software, the North Mara expert logic has been set up to keep a steady and on spec leaching feed slurry while striving to maximize throughput. Leach feed stability was achieved by standardizing operating practices across shifts; a result of successful collaboration with site personnel in developing a consistent control strategy. The strategy maintains the SAG load and power draw in an optimised range by manipulating SAG feed rates and inlet water flow. The project life-cycle was slightly longer than average due to site specific constraints. One of these was the high turnover rate of site?s workforce during the project, coupled with the availability of key staff on site due to the fly in fly out work roster. These constraints called for different, and innovative ways of project commissioning and hand-over. This paper describes details of the control solution, its implementation as well as results and conclusions.

Jan 1, 2009

By M. F. Handley

This paper covers in situ stresses in the Earth?s crust prior to any man-made disturbances, such as mining. It introduces the Southern African Stress Database, which contains primitive stress measurements obtained from locations spread all over southern Africa. The measured stress data shows large variability without any visible trends, except a relationship with increasing depth. The stress database is reviewed briefly, establishing means to measure the variability or dispersion in the measurements, and showing that the dispersion is not as much a result of experimental error as it is a feature of primitive stress. The paper demonstrates from the beginning that the state of stress in rock is highly variable, but that there are well-defined maximum and minimum limits to all the stress components in rock. Formal error analysis is introduced to check the consistency of the database and to separate out a database of consistent stress measurements for use in a primitive stress model. The aim is to provide a picture of primitive crustal stress based on objective stress measurements together with interpretations of how the primitive stress can be affected by the five main influences; namely, depth, rock mass properties, tectonism, isostacy, and erosion. Four elementary models for primitive stress are introduced and compared with the measured data. It is quite clear that none of the elementary models is sufficient to describe the data. In the absence of a better model, this paper suggests a generic model based on the Hoek-Brown failure criterion and the consistent stress database, since it incorporates the variability in the stress tensor that is likely to be encountered underground all over southern Africa. Rock engineers should take every opportunity to obtain local primitive stress data at every mining operation and civil engineering project, and to adjust the proposed model accordingly Keywords primitive stress, Southern African Stress Database, error analysis, generic primitive stress model.

Jun 1, 2013

A high volume of slimes which are separated out during the mining of heavy mineral sands has a high environmental impact and results in great capital as well as operational expenses. The presence of clay minerals drastically increases the slimes volume that needs to be catered for due to its low settling capability as well as swelling characteristics. By adding coagulants in the form of cations and organics, one can improve the settling rate of the minerals as well as the degree of solid bed compaction. The addition of flocculant, which is currently used in industry to improve settling rate, is detrimental to solid bed compaction. By combining the cations and flocculant one can dramatically improve the solid bed compaction. This combination is, however, detrimental to the settling rate of kaolinite-rich slimes but improves the settling rate of smectite-rich slimes. Organics can also be used to produce a clear supernatant and improve the settling rate.

Jan 1, 2010

By H. Edinger

China?s engagement with the African continent has increased impressively in the past decade. Even though China is not the African continent?s largest stakeholder, the rapidly increasing engagement is evident in the huge number of Chinese migrants that have come to Africa in the wake of unprecedented trade and investment levels, as well as in increasing diplomatic and political interactions, which has taken most other commercial partners by surprise. All but four countries in Africa have adopted the ?One China?1 policy stance; and in so doing opened the door for new or strengthened commercial dealings with China, including increasing investments into Africa?s extractive industries. This has been particularly evident since the turn of the century, with a clear shift in China?s policy towards Africa elevating the continent in China?s foreign policy objectives. As such, Africa has become a strategic focus2 for Chinese outward bound and internationalizing companies, especially in the extractive industries. This planned shift in focus is based largely on geo-strategic and commercial needs and interests, rather than previous ideological ones.3

Jan 1, 2011

By C. A. Preece

Finsch Diamond Mine, part of De Beers Consolidated Mines (DBCM), is situated between Kimberley and Postmasburg in the Northern Cape, South Africa. The kimberlite pipe was discovered in 1960 and De Beers assumed full mining rights three years later. Production commenced in 1966 from an opencast mine, and the operation moved underground in 1990 by developing and implementing a new mining method of blast hole open stoping. A mechanized block cave was brought into production in 2005. While block caving was not new to DBCM, with productive caves having operated in Kimberley and Cullinan, from the outset, the Finsch caving operation was designed as the most advanced with a semi-automated ground handling system. The extraction level was laid out as a single sided herringbone system due to the very poor ground conditions on the south side of the pipe. These factors combined to create a unique environment, which necessitated a completely new approach to draw control. The required system was developed by a team consisting of DBCM personnel from head office and Finsch, GEMCOM and Sandvik-Tamrock, the equipment manufacturers. It was essential that the system could be run quickly, provide daily updates and issue calls directly to the LHDs. It was also important that the base data were obtained from the resource model, which was to be depleted on a monthly basis, thus forming a close link between mine planning and draw control. A further requirement of the system was that it would form a central database for the extraction operation where all data pertaining to delays and changes in conditions, be they production or ground condition related, could be recorded and analysed. The design brought together empirical rules and tables developed at Cullinan plus concepts from programming developed for the front cave at Koffiefontein so that the new system was based on sound practical experience. These facets were incorporated into PCBC (GEMCOM) and CMS and PCS (Sandvik-Tamrock programmes). The system has now been operational for just under a year and while modifications have had to be made, it has proved itself as a practical and reliable tool with which to manage the draw control at Finsch. The system is unforgiving and has forced the production team to focus on the specified drawpoints. Problems have been encountered but most of these have been related to re-educating a workforce, familiar with a flexible mining method, to the strict discipline required for a modern block cave.

Jan 1, 2007

By D. Bessinger, H. Kotzé, J. Beukes

Keywords: Pyrometallurgy, furnace, ilmenite, smelting, Ticor Ticor SA began with a detailed feasibility study in 1995. The Hillendale mine (situated between Richards Bay and Empangeni) and Mineral Separation Plant were approved in 2000. The smelter, just outside Empangeni, consists of two 36 MW DC arc furnaces that were commissioned in 2003. Experiences gained during the initial commissioning of the furnaces proved valuable in later commissioning work, as shown by the increase in ramp-up rates. The capacity of the plant is 250 kt/a TiO2 slag and 145 kt/a of pig iron.

Jan 1, 2006

By D. Vogt

South African underground hard rock mines are typically managed using measurements made daily, weekly or even monthly of key parameters such as face advance, readiness to blast, blast success, temperature or dust levels. Safety and health can be greatly improved if a real-time measurement system can inform decision making. To enable this vision of widespread sensing, communication and decision support, CSIR has developed an open standard architecture for communication of sensor data, and a reference implementation using that standard. The standard is called AziSA, which means ?to inform? in isiZulu. AziSA provides an architecture that allows for connection of any type of sensor and that is particularly suited to wireless sensing. On the safety side, the CSIR is developing a suite of sensors specifically around the risk of rockfalls. Sensors such as an electronic replacement for the barring tool, or a thermal sensor that can detect loose rock, can already be used to identify potential hazards in the hangingwall. When these sensors are combined with location and time information in a single database, it becomes possible to build maps of risk and to extrapolate risk into unmined areas. It is also easy to confirm that routine safety procedures like barring are actually taking place. In the future, it is proposed that entry inspections will be made using remote techniques that will not place an individual miner at risk. While miners will still be required to bar or place support, they will do so with a clear idea of which portions of the hangingwall are safe, and which present risk. On the health side, if a network such as AziSA is deployed in the stope, it becomes much easier to monitor the condition of individual miners. The work strain experienced by miners can be monitored through heart-rate sensors, and their core body temperature can be monitored using various novel techniques discussed in the paper. Additional sensors can be added to quantify worker exposure to hazards such as noise or dust. Individual sensors allow for people who are at an unacceptably high risk of developing heat disorders to be treated timeously, and they also allow for team management based on objective measures. Over a longer period, position sensing and environment monitors, or personal dosimetry, provide a powerful management tool to prevent workers from being overexposed to hazards, and to confirm that management instructions are being followed. Cost-effective sensing in the stope is a major challenge, but one that can be overcome through technology like that used in AziSA. Sensing provides opportunities both to make immediate interventions when workers are exposed to unacceptable risk, and to manage the long-term exposure of workers to hazard.

Jan 1, 2010