Search Documents

By Richard J. Bielicki

Poor mixing of methane and air at coal mine working faces causes fluctuating methane concentrations. If these fluctuations are large enough, methane levels can periodically exceed safe limits, even though the time average methane concentration may be satisfactory. Concentration fluctuations measured underground can result both from variations in methane emission rate and poor mixing. The present paper reports on a statistical analysis of fluctuations at a constant methane emission rate, that is, on fluctuations due only to poor mixing. A full-scale model of a working face was used. Both peak heights and elapsed times between peaks were evaluated. Good mixing was indicated by normal, Poisson, and exponential distributions while poor or incomplete mixing was indicated by log-normal or gamma distributions.

Jan 1, 1974

By W. F. Marshall

The Bureau of Mines conducted a series of experiments to determine the influence of exhaust rebreathing on emissions from various gasoline and diesel engines. Tests were conducted that simulated operation of engines in nonventilated spaces as well as in spaces with partially restricted ventilation. Results of these tests showed that exhaust rebreathing can have a marked effect on exhaust emissions and thus on the composition of the air in the working space. For the case of restricted ventilation, unacceptably high (greater than 50 ppm) levels of CO in the air of the working space resulted from exhaust rebreathing rates as low as 8 pct exhaust in the engine's intake. Operation in a nonventilated space resulted in highly critical CO levels (fatal in a few minutes) at times corresponding to 1 to 3 pounds of fuel consumed per 1,000 cu ft of space. Tests involving spaces of various sizes showed that volume of the air space [per se] is not important--the primary variable is fuel consumed per unit volume of air space.

Jan 1, 1973

By Roger J. Morrell

The Bureau of Mines conducted drag cutting experiments in hard, abrasive rock in an effort to extend the capabilities of an experimental kerf-core mining machine. The basic kerf-core mining machine cannot be used in hard, abrasive rocks because of the high wear experienced by the kerf cutters. These experiments were conducted in an effort to develop a method of preweakening the rock ahead of the kerf cutters in order to reduce the high cutting loads and hence the higher wear rates experienced by the cutters. The two "preweakening" techniques studied were indenting with mechanical wedges and single and double slotting with diamond saws. The best cutter force reduction achieved with mechanical indenting as 70 pct, whereas double slotting achieved force reductions of up to 99 pct. Conceptual designs of preweakening systems that could be retrofitted onto the basic kerfing cutterhead were developed for both the indenting and the slotting techniques. A high-energy impactor with wedge bit was used for the indenting method, and high-pressure water jets were used for the slotting method. A preliminary technical and economic analysis was performed for both of these full-scale systems to illustrate the methodology and to point out the important technical and economic factors that must be considered.

Jan 1, 1987

By R. V. Ramani, A. S. C. Owili-eger

This report was prepared by The Pennsylvania State University under USBM Contract No. G0111808. The contract was initiated under the Coal Mine Health and Safety Program. It was administered under the technical direction of DMSE, with Mr. G. R. Schottler acting as the technical project officer. Mr. J. A. Herickes was the contract administrator for the Bureau of Mines. This report is a summary of the work recently completed as part of this contract during the period June, 1971 to December, 1973. This report was submitted by the authors on March 31, 1974. Part of the research reported here was originally done on a grant from the Department of Environmental Resources, Commonwealth of Pennsylvania and reported in Special Research Report No. SR-95 (February 25, 1973) of the Coal Research Board, The Pennsylvania State University.

Jan 1, 1974

By Alan H. Goode

As part of the Bureau of Mines program to broaden utilization of abundant low-quality mineral materials, the Tuscaloosa Metallurgy Research Laboratory conducted beneficiation studies on two Alabama clays. The main purpose of these studies was to develop improved plasticity and green strength in both clays and compare these improved properties with those of a typical ball clay. Whiteness of the clays was also considered. The results indicated that by adjusting the pH of the kaolin to approximately 9, a substitute for ball clay could be obtained. The investigation also showed that by a combination of attrition grinding and sodium dithionite leaching to remove iron, the underclay could be upgraded to a ball clay material.

Jan 1, 1975

By Seth C. Schaefer

The Bureau of Mines studied thermodynamic properties of Al-Ni alloys con¬taining 0.54 to 30.04 atomic percent nickel with the aid of the high-temperature galvanic cell Al(1) // Al+3 (AlCl3 in NaCI.KC1) // Al-Ni alloy (1 or s). Activities of aluminum and nickel (compared with pure liquid metals as the standard state) show pronounced negative deviation from Raoult's law at 1,273 K. The properties [?G, ?Gxs, ?G ideal, ?GA1, AGxs1, ?Gni , and ?GNixs] have been derived from the experimental data and are summarized in tables and illustrations. At 1,127 K, the thermodynamic stability for the invariant three-phase equilibrium consisting of a saturated liquid, A13Ni, and A13Ni2 has been uniquely defined by an activity for aluminum of 0.751. A free energy of formation at 1,127 K of -7,940 cal/g-atom was derived for the compound A13Ni.

Jan 1, 1975

By F. S. Karn

Measurements were made of the flow of helium, methane, ethane, butane, and toluene through thin disks of coal. All measurements were made on a dense layer in the Pittsburgh seam identified as attritus. Flow increased with pressure differential and temperature. At room temperature and a pressure differential of 1 atmosphere flow rates along the bedding plane of Pittsburgh seam coal were helium 881 X 10-10 cm2 sec-1, methane 1.2 X 10 -10 cm2 sec-1, ethane 0.54 X 10-10 cm 2 sec-1, n-butane 0.35 X 10-10 cm2sec-1, and toluene 3.8 X 10-10 cm2sec-1. Flow rates were 50 percent lower across the bedding plane of the coal than along the bedding plane. Activation energies were 3.9 kcal mole-1 for helium and 13.6 kcal mole-1 for methane, with diffusion measured either along or across the bedding plane.

Jan 1, 1970

By E. R. Maize, R. D. Currie

"Good ventilation is one of the first requisites in the safe and efficient operation of a coal mine. If a mine is gassy, the uninterrupted circulation of an adequate supply of fresh air is imperative if that mine is to operate with a relative degree of safety. That ventilation is not •only a safety consideration, but is an extremely important economic factor is shown by the fact that in many mines 50 per cent of the total power cost is for ventilation.The system used in the Graceton Coal & Coke Co. mine, Graceton, Pa., is believed to be unusual in many ways. Its application in this mine has re¬sulted in good ventilation of the working faces, no interruption to the venti¬lating current through the use of doors. a large- portion of the air circulated by the fan reaching the working places, low velocity air currents on traveling and haulage ways, low water gage and power consumption of the fan, and well-ventilated gob areas.This investigation was made possible through the courtesy of W. H. Robertson, mine superintendent. Fred Roberts, mining engineer, and Floyd Phillippi, mine foreman, assisted in the collection of information.The Graceton mine is a slope, opening the Upper Freeport or E bed, on the Pennsylvania Railroad about midway between Blairsville and Indiana at Graceton, Indiana County, Pa. The production is approximately 1,000 tons of coal per day and about 170 men are employed underground. The mine is considered gassy and was found to be liberating approximately 300,000 cubic feet of methane in 24 hours. The return airways terminate at a circular, concrete lined shaft 12 feet in diameter and about 115 feet deep at which is the exhaust fan.Mining is done by a block system with flat or level entries turned off the main slope at intervals of 1,350 feet, off which the butt headings are turned up the grade parallel to the slope. Rooms, which are about 225 feet long and 12 feet wide, are turned off the butt headings on 80-foot centers, leaving a block about 68 feet thick between rooms.Haulage on the main slope is by rope, with the hoist on the surface. This hoist is electrically driven through a 500-h.p., 2,300-volt motor. The rope used in this haulage is 1-1/8 inches in diameter. There are five electric trolley locomotives - one 10-ton and four 6-ton - which do all of the hauling in the flat and butt entries.Before it is blasted all of the solid coal and as much of the pillar coal as can be cut with safety is undercut by permissible mining machines. Shooting is done by shot firers who use permissible explosives, electric detonators, and dry-cell, nonpermissible batteries.In rooms where conditions are normal, timbering consists of two rows of posts on 4-foot centers. Posts are required to be within 6 feet of the face in machine-cut places and within 3 feet of the face in hand-mined places. Timbering on entries, where required, is of two types: a bar hitched into the ribs and supported by the coal, or 3-piece sets. The legs of the 3- piece sets used on the slope are set well back into the rib to prevent their being. knocked out by a wreck."

May 1, 1932

By Robert M. Doerr

In a process being investigated by the Bureau of Mines for recovering alumina from domestic nonbauxitic resources, calcined kaolinitic clay is leached with hydrochloric acid. Iron impurity in the clay is coleached and is removed in a solvent extraction step prior to crystallization of aluminum chloride hexahydrate, which is subsequently thermally decomposed to alumina. The FeCI3-HCl stripping liquor from the solvent extraction step is unsuitable for discharging to the environment; furthermore, economics requires recovery of the contained chloride values. In the present research, it was shown that the stripping liquor can be reacted with calcined clay to yield AlC13 in solution, plus precipitated iron oxides, residual silica, and unreacted excess clay as mixed solids. For the recovery of the AICl3 solution, the slurry could be separated or returned to the clay-HCI process stream at the solids washing step that follows primary HCI leaching of the clay. For the range 20° to 99° C, the time (t) (103 sec) required to react the waste liquor with excess clay, for essentially complete iron precipitation, depends on the absolute temperature (T) chosen, according to the expression t = e[(9.000/T) -23.5J. (1) Alumina was tried as a reagent alternative to clay but was not very effective, even under pressure and at high temperatures.

Jan 1, 1982

By David Cooper, Susan Robertson, William Wiehagen, Launa Mallett, Charles Vaught, Joan Dickerson, Richard Conkle, ROBERT PETERS, Mike Brnich, Charles Urban

This trainer’s guide is designed as a reference manual. The purpose is to offer information and examples to skills trainers to assist them in structuring training for new operators of Walk-Thru roof bolting machines. Trainers can use this manual as a resource for helping trainees learn, understand, and apply knowledge and skills. In this sense, the guide is not prescriptive. It is designed to offer information and trigger ideas on what might be done to accelerate learning to those who are new to the roof-bolting task. On-site trainers can modify this guide to fit their conditions, machines and equipment, and work procedures. They can integrate roof control plans, company policies and procedures, and operators’ manuals from the manufacturers of the original equipment into this guide. Every trainee is different and will come to the job with varying levels of relevant knowledge and skills. The trainer’s decisions on where to start, how to organize the on-the-job and classroom training portions, and when and how to offer different aspects of the training will be based on (1) a pretraining assessment of the trainee’s knowledge and skills and (2) the trainer’s experience in conducting skills training. The “Skill Check” section might be useful for deciding where training should start among miners who have underground experience but limited knowledge of roof-bolting techniques. Every job carries a learning curve and likely has a number of “teachable moments” where significantly new knowledge and skills can be learned. The videos on the DVD that accompany this guide can be shown at the beginning of training to give trainees an idea of what the job entails and related requirements. They can also be used within the training cycle (after the trainee has some experience in the job) to reinforce key points or as a trigger for eliciting questions about particularly difficult parts of the job. The video segments are meant to be visual models of good performance. They are designed to elicit discussion on good (lower risk) ways to do the job. In this context, they can be used very creatively at different times within the training cycle. The section on “Talking Points” offers a number of questions that can be used in the classroom to support and elaborate on certain aspects of the job duties. If the trainee has a fair amount of underground experience, some of the questions can also be used to support the pretraining assessment (i.e., skill check) of knowledge and skills. Likewise, some of the questions can also be used while teaching on the job to reinforce key points affecting safety, production, or maintenance. The section dealing with a mine’s roof control plan should be used at various times in the training cycle to make sure the trainee understands the plan and knows how to apply it in performing the job. The supplemental materials offer additional resources that can be used to support initial job training or follow-up. Learning continues well after an individual has been trained. The supplemental materials can help reinforce good operating skills and provide an opportunity for further discussion on better ways to do the job.

Jan 8, 2006

"There mines are located in out of the way places, where timber is scarce and its price high, the problem of protecting it from fire risk is of considerable practical importance. Scarcity of timber for mining purposes is commonly met with in the more arid parts of the country, where, so, mine timbers are most likely to become dry, and inflammable, and where, therefore, the risk from fire is accentuated. Any effective and cheap method of securing adequate protection of such timber at the lowest possible cost is worthy of careful investigation. The use of magnesite cement has been suggested in this connection.The necessary qualities for any substance for the use suggested above may be summarized as follows: It should be resistant to abrasion, and to impact and structural stresses. It should be durable when subjected to the action of the elements, and stable to any minor derangements of the base on which it is placed. It must be relatively unaffected by changes in temperature, by the action of water, and should adhere to the material on which it is placed, and it should also be free from shrinkage cracks due to setting up the material, Magnesite cement appears to fulfill the various conditions outlined above.The elasticity of such cement is the outstanding quality which makes it desirable for exterior work. It also possesses the ability to adhere to all materials in a marked degree. Its freedom from expansion and contraction after setting is one of the principal reasons for its adhesive quality. It may be applied to old brick or stone walls, even tho they have been repeatedly covered with paint, and the quality of adhearing to wood makes it possible to secure a weather-proof protection to the wooden casings and trim of exterior openings. The quality of adhesion and elasticity is easily proved by applying a 1/2"" layer to a 1"" board which has been first covered with metal lath. Such a board, about 8 feet long, may be repeatedly deflected about 3"" in the center without breaking the bond to the board, or causing any cracks to appear in the magnesia cement. The ability to resist fire as well as the possession of insulating qualities are also desirable characteristics of magnesia cement stucco.Magnesite cement stucco should be applied in two coats, each 1/4"" thick on various surfaces such as wood lath, metal lath, sheathing board, brick, hollow tile, or stone; care being taken as regards the presence of lime, unless the same has been rendered, or become inert as with very old, walls. The first coat made up to a consistency that works easily under the trowel is applied in the usual manner. No water should be added to the liquid chloride as it would alter its density, and injure the work. The second or finishing coat is then applied. The aggregates are different in each, and no other dry material should be added to them as they come to the trade. The cement may be applied in zero weather without damage. Setting is quite slow under such conditions, but the cement ultimately becomes hard. It should always be applied to a dry surface excepting that under certain conditions it is desirable to apply a solution of magnesium chloride before using the stucco."

Dec 1, 1919

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

7. Hoisting Systems Hoists used solely for emergency escape use should above all, be simple and dependable. The hoist systems' motive power should be independent of all other mine equipment so that only an emergency in the immediate vicinity of the hoist will render it inoperative. The hoist should receive the same high level of inspection as is normal with any other man hoisting system. It should be operated at regular intervals, and must include sufficient safety devices to ensure safe operation when hoisting men. Of equal importance, however, safety devices must be included to safeguard the hoist system from in¬advertant damage due to inspection, maintenance or operator error In an emergency situation the hoist operator will be under considerable stress and the system must be simple and foolproof to operate. Under normal circumstances the hoist will only be operated during the regular inspection cycle. Because of this very low operational use rate, certain requirements, normally associated with man hoisting, can be relaxed. In particular the wire rope installation requirements, in terms of drum and sheave diameter and fleet angles, can be reduced provided that rope inspection during the system life is maintained at a high level. The following section includes recommended guidelines for emergency hoist system design, installation, operation, maintenance and inspection A summary of available hoisting equipment and components is included in Appendix C. Emergency Hoist Guidelines All hoists designated as part of a mine emergency escape system shall meet the requirements of the Emergency Hoist Guidelines. Where these hoists are also utilized for hoisting other than emergency hoisting, the requirements of Title 30, Code of

Jan 1, 1976

By Bernard Porter

Differential thermal analysis measurements were used to characterize a phase diagram for the KF-YF3 system at compositions between 0 and 60 mole-percent YF3, A congruent melting point compound was observed at 3KF?YFs, which melts at 965°±5° C and undergoes solid-state decomposition at 725°±2° C. One peritectic and two eutectic compositions are also defined.

Jan 1, 1969

By K. D. Luxbacher

Understanding methane emissions in underground coal mines is critical for a safe and productive mine. In addition to reasonable estimation of initial coalbed reservoir parameters, it is also crucial that changes in effective stress due to mining and pore pressure reduction are taken into account due to their effects on porosity and permeability. Primary parameters for estimation of emissions or modeling of the mining environment for this purpose are porosity and permeability which can change dramatically as a result of stress redistribution associated with mining and gas desorption from a large coal volume. These parameters affect the emission rates and ventilation requirements, as well as water inflow into the working environment. Stopping leakage, on the other hand, is a secondary stress dependent factor in estimation of emissions, as convergence of the roof and floor strata, compromising the integrity of the stopping, may result in leakage, making prediction of ventilation requirements difficult. This paper aims to examine the effects of porosity and permeability changes of the coal seam on methane emissions in an underground continuous miner section. The models were developed and executed in a dynamic fashion to simulate an advancing section. Through this process, the changes of effective stress in coal, particularly their change paths, on porosity and permeability were incorporated into the models and methane emissions, concentrations, air requirements, water inflow and possible leakage from the stoppings were investigated using a conventional coalbed methane reservoir model.

Jan 1, 2009

By M. Viswanathan, M. J. Jorgensen, N. K. Kittusamy

Operating heavy construction equipment is often associated with elevated rates of low back discomfort (LBD). However, there have been few formal studies that dealt with evaluating controls that can reduce the LBD among these workers. The objective of this study was to determine the effectiveness of using a continuous passive lumbar motion system (CPLMS) in reducing low back discomfort among operators of heavy earthmoving equipment. The CPLMS is an additional seat support that has a lumbar support bladder and a pump to provide cyclic inflation and deflation. Two groups of operators were identified as potential subjects for this intervention study, the intervention group with a mean age of 41.2 years and experience of 9.7 years used the CPLMS, and the control group with a mean age of 37.5 years and experience of 7.6 years did not use the CPLMS. Body part discomfort surveys were collected from both groups. In addition, the intervention group completed a CPLMS preference survey. The body part discomfort survey was collected up to eight days at three different times of the day. Results from the body part discomfort survey showed a decreasing trend the longer the CPLMS was used, for both the upper and low back region. A decreasing trend for the low back was also found comparing morning to evening discomfort scores across the days when using the CPLMS. When compared to their regular seat, 54% of the operators felt very comfortable in using the CPLMS, 36% of them wanted one for their equipment, and 54% showed interest in experimenting with the CPLMS for a longer time period. Results from this study indicate that the use of a CPLMS can effectively reduce the low back discomfort experienced by operators of heavy construction equipment.

By S. E. Khalafalla

The ability of potentiometric, gas-sensing electrodes to reliably monitor free gaseous molecules in solution has been recently demonstrated. A gas such as sulfur dioxide from a dilute sample solution diffuses through a hydrophobic, gas-permeable membrane to an internal filling solution. The latter solution contains a sufficiently large excess of sodium bisulfite, the concentration of which can be considered constant regardless of the quantity of sulfur dioxide entering by diffusion. The electrode response is essentially due to the liberated hydrogen ions from the bisulfite-sulfur dioxide equilibrium. This Bureau of Mines report describes a new technique used to detect the formation, and to estimate the stability constant, of gas-molecule and gas-ion complexes in solution, as part of an effort to minimize the undesirable environmental impacts associated with mining and mineral processing. Although the unknown activity coefficients of the neutral and ionic species in the external solution complicate the quantitation of results, methods to circumvent these difficulties are presented. The technique is based on the isometric shift of the Nernst diagram of ion-selective electrodes to higher concentrations relative to the standard aqueous calibration curve. The method is applied to detect and estimate the formation constant of a sulfitocitrate complex, and agrees well with an independently determined stability constant of the disulfitomercu-rate complex.

Jan 1, 1978

By Ronald D. Hill, Elmore C. Grim

The goal of blasting is to get maximum fragmentation of the consolidated material in the overburden with optimum drilling and blasting cost. The amount of fragmentation required is determined by the stripping unit to be used In overburden removal. Many coal seams must also be broken by blasting; this is conducted before coal removal. There are environmental factors as well as due regard for public safety, health, and welfare that must be considered in choosing the blasting plan. The blasting plan should be made during preplanning and is based on data from the overburden cores. Analysis of the data will help In determining the kind of drilling equipment and bit types that will be needed for overburden preparation.

Jan 1, 1974

To suppress the natural bacterial action in acid mine drainage (AMD), the major contributor to acid formation. Approach Recycle partially-treated affluent back to the source of AMD within a mine, or to the coal or coal-waste stockpile. This effectively eliminates any further biologically-promoted AMD by inhibiting catalyzed weathering or oxidation by acid-forming bacteria. How it Works AMO-type effluents can be largely reduced by "recycling" the acidic outflow back to the source of AMD within a mine or to the Input side of a waste pile to percolate through the reactive pyrite and bacteria mixture. The bacteria in the cell thrive on the oxidation of ferrous to ferric iron through the electron transfer, Fe2 +[=]Fe3 + + e. Its reaction product [s, therefore, essentially ferric iron. While small quantities of Fe3 + will not interfere with the exponential multiplication of the bacteria

Jan 1, 1982

By Robert W. Freedman, Benjamin I. Ferber, Wayne H. Duerr

Vacutainers are employed by the Bureau of Mines and the Mining Enforcement and Safety Administration for sampling mine air and other atmospheres containing fixed gases, low-molecular-weight hydrocarbons, and products of combustion. Tests were conducted to study shelf life of evacuated samplers prior to sampling and also to check the stability of sampled gases prior to analysis. An unexplained phenomenon, slow accumulation of carbon monoxide in evacuated samplers, occurred after a few weeks' storage; levels were low but increased with time and could pose a problem for critical applications. Accordingly, attempts to halt CO release by additional means of treatment were made, and storage at low temperature was found to be effective.

Jan 1, 1978

By J. A. Eisele

As part of its goal of maintaining an adequate supply of minerals to meet national economic and strategic needs, the Bureau of Mines has studied the removal of iron from simulated aluminum nitrate leach liquors by solvent extraction. Iron must be removed from aluminum nitrate liquor produced by leaching calcined kaolinitic clay with HN03 to reduce the iron level in alumina to less than 0.02 wt-pct Fe203 for use in reduction cells. The parameters reported are for (1) extracting iron from a feed containing 1.5 g/l Fe with di(2-ethylhexyl) phosphoric acid (EHPA), (2) stripping loaded organic phase with 20-pct HCI, and (3) water washing of loaded and stripped organic phase. Recommended operating conditions are two extraction stages using 15 vol-pct EHPA in kerosene and three stripping stages using 20-pct HCI. Results are also given for tests using other extractants and stripping agents.

Jan 1, 1982