Search Documents

1. Data from the Mine Safety and Health Administration (MSHA) indicate that a total of 241,502 employees worked in surface mining locations in 2003, corresponding to 212,113 full-time equivalent (FTE) workers. • Surface employees accounted for 84.6% of all mining employees. • The majority of surface employees (73.7%; n = 177,927) were mine operator employees as opposed to contractor employees. • Stone operator employees comprised the greatest percentage (27.2%; n = 65,743) of surface employees.

Feb 1, 2005

By Wesley A. Grosh

The Vest nickel prospect, in Floyd County, Va., was discovered about 25 years ago. Limited exploration of the deposit had indicated some appreciable nickel mineralization in the sulfide ore. The property was examined on March 9, 1943, by an engineer of the Bureau of Mines in company with C. W. Vest, owner of the property. A limited exploration program was recommended. Two holes totaling 320 feet were diamond-drilled in January 1944. Drilling indicated the sulfides are sparsely disseminated. The only nickel values of interest were at the old prospect shaft.

Jan 1, 1949

By J. E. Murphy

The Bureau of Mines developed a hydrometallurgical method for recovering mercury metal from mercury sulfide concentrates. Sulfide flotation concentrate from the McDermitt Mine was leached in a cupric chloride solution at 80° C. The redox potential of the solution was maintained at 850 mV during leaching by chlorine sparging. Mercury extractions exceeded 99 pct in 3 h of leaching. After leaching, the pH of the solu-tion was increased from 1 to 4.5 to precipitate copper as atacamite. The pregnant solution typically containing 100 giL Hg was sent to elec-trolysis to produce high-purity mercury metal and chlorine for recycle. In a 200-A electrolytic cell operated for 24 h, current efficiency was 99 pct and the energy requirement was 0.9 kW·h/lb of mercury produced. Mercury removal from the waste stream was also investigated. Iron or zinc cementation, sulfide precipitation with H2S, and activated carbon adsorption all decreased the mercury concentration from 10 giL to 0.01 mglL, which is less than the Environmental Protection Agency limit on wastewater of 0.02 mg/L.

Jan 1, 1987

By Wilber Duvall, Leonard Obert

"INTRODUCTION This report is the first of four to be presented on the microseismic method 4/ of predicting rock failure in underground mining. The application of the microseismic method to one specific case, namely, that of predicting rock bursts in deep mining, has been described in two previous reports. 5/ 6/ Since the publication of these reports 5/ 6/ the method has been extended to other fields of mining, end it is the purpose of this report (Part I) to describe the general microseismic method, giving the empirical facts upon it is based, the different testing procedures, the method of recording and analzing the data, and the interpretations that can be obtained there-from. Part II will describe a series of laboratory experiments that were performed to give information on the origin of microceismims and the microseismic properties of various rocks. Part III will cover application of the method to specific mining problems together with a brief description of a number of investigations performed during, the last three years. Part IV will describe in detail the microseicmic equipment used in the various phases of these investigations."

Feb 1, 1945

By E. G. Valdez

Iron foundries that melt automobile scrap produce flue dusts averaging about 32 percent zinc and 6 percent lead. Some is sold to smelters, but because of the meager return and difficulty in handling, most of the dust is discarded. As part of the Bureau of Mines program to find uses for mineral wastes, research was initiated to develop an economical process to recover zinc and lead from the flue dust. Research encompassed the extraction of zinc and lead by fuming, leaching, and agglomeration. Controlled vacuum fuming of zinc to produce Prime Western zinc and a lead-rich residue was the most effective method for treating the dust. This process involved two distillations, or fumings, with carbon and methane as reductants, and resulted in recovery of 91.4 percent of the zinc in a Prime Western grade product, and 98 percent of the lead. Hydrometallurgical techniques involved several leaching methods, but the simultaneous extraction of iron, manganese, and copper resulted in contamination of the solution and made the zinc recovery processes too complicated. Agglomeration was done by pelletizing or briquetting the dust for possible use as feed to a zinc smelter.

Jan 1, 1975

By L. B. Berger

"Additions to List Published in Information Circular 7444 NEW APPROVALSThe following respiratory protective devices have been approved by the United States Department of the Interior, Bureau of Mines, since Information Circular 7444 was issued (March 1948):Gas Masks Approved Under Schedules 14, 14A, 14B) 11+D, and 14E Type N: Universal Gas MasksUniversal gas masks with filters that afford respiratory protection against smoke from ordinary fires and limited respiratory protection against dusts, fumes, mists, and fogs but do not afford respiratory protection against the toxic smokes of warfare.Willson WUG-Nl universal gas mask. Approval BM-1443, issued to Willson Products, Inc., May 25, 1948.Bullard universal as mask. Extension of approval BM-1443, issued to E. D. Bullard Co., January 12, 19 9.Supplied-air Respirators Approved Under Schedules 19 and 19A Type C: Air-line Respirators4. METCO air-line respirator. Extension of approval BM-1920, issued to Metallizing Engineering Co., Inc., December 8, 1948.Type CE: Abrasive Blasting Helmets, Hoods, or Masks9. M.S.A. abrasive mask. Approval BM-1920, issued to Mine Safety Appliances Co., April 30, 1948."

Apr 1, 1949

By W. A. Selvig

"INTRODUCTION In 1942, Lowry and Junge 3/ reported the results of a statistical study of errors for the proximate and ultimate analysis of coal and coke when made according to the standard Methods of Laboratory Sampling and Analysis of Coal and Coke (D271-42) 4/ of the American Society for Testing Materials. Some of the laboratories that cooperated in the investigation reported difficulty with determination of the volatile matter of anthracite and low-temperature coke. The small number of analyses reported for these particular fuels was considered inadequate to justify definite conclusions regarding the precision of this determination.The investigation described in this report was made at the request of Committee D-5 on Coal and Coke, A.S.T.M. (A. C. Fieldner, chairman), to secure additional information regarding the errors of the volatile matter determination for anthracite, low-temperature coke, and subbituminous coal; the last fuel also gives trouble in this determination, The committee has recognized that the allowable differences between duplicate determinations of volatile matter for these fuels as given in the standard methods are perhaps too stringent and may require revision."

Dec 1, 1943

By A. Gene Collins

During recent years the interest in trace and minor constituents of oil-field water, petroleum, and their associated reservoir rocks has increased. The metals copper, nickel, lead, manganese, iron, zinc, and cadmium are not determined routinely in oilfield brine analyses. Determination of these metals and subsequent correlation of these data should yield information to aid 1n the interpretation of the origin of different waters. The methods of analyzing oilfield waters have several potential applications: (1) Aiding in the search for petroleum; (2) identifying sources of intrusive brines; (3) controlling corrosion; (4) controlling produced water; increasing knowledge of the geology of subsurface formations; (5) identifying incompatible waters in waterflooding operations; (6) increasing the knowledge of the flow of oil, gas, and water in underground formations; and (7) aiding in the identification and location of valuable mineral reserves. Some brines contain enough valuable minerals to be recovered commercially.

Jan 1, 1962

By E. G. King

Cerium and thorium sulfides have found use as crucible materials for melting certain radioactive metals. However, thermodynamic treatment of these sulfides has been hampered by lack of experimentally derived entropy values. This Bureau of Mines report describes heat-capacity measurements between 51° and 298° K, and entropy evaluations at 298.15° K, for cerium monosulfide (CeS), cerium sesquisulfide (Ce2S3), and thorium disulfide (THS2). The entropy values, with Literature results for the heats of formation, are used to obtain free energies of formation at 298.15°K. MATERIALS The samples used in this work were supplied by Prof, Leo Brewer of the Department of Chemistry, University of California. The methods of preparation and some of the physical and chemical properties of these sulfides were given by Eastman and coworkers.3 4/ Chemical analyses, conducted in our laboratory, gave the following results:

Jan 1, 1959

By R. E. Stiles

The modified perchloric--EDTA method devised by the Bureau of Mines for the determination of copper in high-grade samples gives results that are more precise and more accurate than those from the classical sulfuric-iodometric method. Although the perchloric--EDTA method is more costly than the conventional method, the savings in time alone largely offsets this difference. Specifically, the modifications wade in the more conventional procedure comprise (1) use of perchloric acid instead of sulfuric acid for dissolution of copper minerals, (2) precipitation of copper as copper sulfide from dilute perchloric acid solution, (3) wet oxidation and dissolution of the precipitated copper sulfide, (4) use of larger amounts of indicator than those employed in the Schwarzenbach method of titrating low-tenor copper solutions with disodium ethylenedinitri10-tetraacetate and murexide indicator, and (5) use of refrigeration to partially stabilize aqueous solutions of the indicator.

Jan 1, 1966

Introduction The Coal Mine Roof Rating (CMRR) is a roof classification system. It was first introduced to the mining community in 1994.The CMRR filled a longstanding need to quantify geologic description of coal measure rocks into an engineering value that could be used for mine design. It has now been written to a user-friendly visual basic code that can be run on any PC with a Windows operating system. Background Rocks that form the roof of coal mines can vary widely and quickly in composition, extent, and defects. This results in an equally broad range of rock properties that can substantially affect the ability of the rock mass to form a stable mine roof. The CMRR was designed to evaluate the properties of the coal mine roof rock mass that contribute to its weakness and convert them into a relative strength rating from 0 to 100. These properties include the cohesion and frequency of discontinuities like bedding, slips, shears, and joints; uniaxial compressive strength (UCS); and moisture sensitivity. With simple lab and field tests and observation, the CMRR can be calculated by technical and operating personnel with a minimum of training. The CMRR has been widely accepted in both U.S. and international coalfields. As a result, a number of roof control applications have been found for the CMRR. It is currently used as an input component in the Analysis of Longwall Pillar Stability(ALPS) program, which is used to design longwall chain pillars. Incan be used as a criterion for determining the appropriate width of mine entries. It has also been used to indicate the appropriate length of cut in weak ground. The CMRR can be used as a strength parameter to characterize inter burden between mined seams in the numerical modeling of subsidence effects. In any area where an estimation of coal measure rock mass strength is required, the CMRR can be adapted to fill this need. How It Works Originally designed to be used with underground exposures, the CMRR can also be calculated from core. The chisel test for bedding cohesion and the ballpeen hammer test for UCS are inappropriate for core. These tests have been replaced by point load testing both axially and diametrally. Two other measures that are common to standard core logging—Rock Quality Designation (RQD) and fracture spacing—are also used to estimate rock weakness. With these easily obtained parameters, the CMRR can be calculated from core and used in the mine planning and exploration phase. The input screens allow calculation of the CMRR for both underground exposure and core. The CMRR is reported both as a “dry" value and as a groundwater-adjusted value for moisture-sensitive rocks. There is a graphical output report featuring a lithologic column with annotated unit ratings and a roof bolt symbol representing the height of the bolted horizon. Another important feature is an AutoCAD interface. This feature allows the export of located CMRR data directly to an AutoCAD layer in XYZ form. In this way, drill hole data can be inserted directly to a base map.

Apr 1, 2003

By L. W. Scott, T. H. Dubaniewicz, F. T. Duda, P. G. Kovalchik

Recent research conducted by NIOSH, Pittsburgh Research Laboratory showed that electrical current levels permitted under parent regulations may not limit cable temperatures to less than 90 °C in reeled trailing cables. Reeled cables, tightly wrapped with many turns, ell carrying current in an enclosed space, can become overheated due to poor heat transfer. This overheating can cause the cable insulation to soften and become easily damaged. The damaged insulation reduces the life of the cable and can lead to shock, electrocution, and mine foes. This paper describes a method of measuring the conductor temperature of untie trailing cables during no anal operation. The temperature is measured using a 50/175 micrometer Graded Index Multimode Optical Fiber located in the center of the metallic conductors. Distributed temperature measurements arc made using an Optical Time Domain Reflectometer (OTDR). This system is capable of measuring temperature with an accuracy of plus or minus one degree centigrade over a length of 4 km at 1-m intervals. With this unique way of measuring temperature, tests can be conducted simulating actual mine conditions and provide important data to allow MSHA's Approval and Certification Center to develop approval criteria for cyclically rated reeled machines.

By John W. Adams, W. D. Bensema, Motohisa Kanda

Two different techniques were used to make measurements of the absolute value of electromagnetic noise in an operating coal mine, Robena No. 4, located near Waynesburg, Pennsylvania. One technique measures noise over the entire electromagnetic spectrum of interest for brief tine periods. With present instrumentation, the spectrum can be covered from 40 Hz to 400 kHz. It is recorded using broad-band analog magnetic tape, and the noise data are later transformed to give spectral plots. The other technique records noise envelopes at several discrete frequencies for a sufficient amount of tine to provide amplitude probability distributions. The specific measured results are given in a number of spectral plots and amplitude probability distribution plots. The general results are that at frequencies below 10 kHz, power line noise within the mine is severe. Impulsive noise is severe near arcing trolleys, and at lower frequencies near any transmission line. Carrier trolley phone signals and harmonics are strong throughout the mine whenever the trolley phone is in operation. Additional information beyond that included in this report may be obtained from the authors, who are with the Electromagnetics Division of the National Bureau of Standards.

Jan 4, 1974

By E. J. Ostrowski

The Bureau of Mines experimental blast furnace, Bruceton, Pa., was operated to determine the feasibility of replacing part of the burden coke requirements with solid fuels injected directly into the smelting zone. This report describes preliminary experiments and information resulting from such an interchange. These experiments were made on an all-sinter burden, using two parts sinter to one part fuel. Anthracite fines were injected intermittently into the smelting zone of the furnace by compressed air through auxiliary tuyeres. The interval between injection periods ranged from 5 to 15 minutes. A maximum of 28 percent of the stock column coke bur-den was replaced. This percentage replacement caused furnace malfunction, but the overall percentage of these experiments indicated that 20 to 24 percent of the coke requirements could be replaced in this way. The metallurgical coke consumption was decreased by as much as 377 pounds (25.3 percent) per ton of pig metal produced. Buckwheat anthracite No.4 was used in this experiment; however, such solids as bituminous coal or coke fines also could be used. The frequency as well as the quantity of solid fuel injected has a direct bearing on furnace performance.

Jan 1, 1960

By J. W. Paul

This paper deals with the second phase of an extensive research on coal-mine ventilation factors. A comprehensive report of the entire work is in course of preparation, but abstracts of the various chapters are being prepared in order to make the results public as rapidly as possible. Part 1 dealt with the resistance of unobstructed entries and was issued as Serial 2621 of the Bureau of Mines, in July 1924. Description of tests. After the resistance of an unobstructed entry to flow of air had been determined by tests in the Experiment mine, mine cars were; run into the test section in various arrangements and the increase in resistance was determined. The cars used were of the wooden type with loose end gate, and would hold about one ton of coal, level full. They were 7 feet long. 4 feet 2 inches wide above the wheels, 3 feet high, and had a cross-sectional area of approximately 10 square feet. The average area of the entry was about 57 square feet, the ratio of unobstructed to total area being about 17.6 per cent. The track gage was 42 inches and the wheel-base 20 inches.

Jan 1, 1924

Objective To develop a passive, inexpensive technique for monitoring explosion overpressures within sealed areas in underground coalmines. Background From 1994 to 2000, seven explosions of methane and/or coal dust occurred within the worked-out, sealed areas (gobs) of underground U.S. coal mines. These explosions, believed to have been started by lightning, destroyed many seals and caused much damage external to the sealed area. One gob explosion went undetected until the mine operator reopened the sealed area and discovered the damage. Fortunately, these gob explosions did not cause any fatalities or injuries. Because lightning occurs in just about all mining areas, several questions arise. Could gob gas explosions be occurring in other sealed areas and going undetected? If so, what is the magnitude of the resulting explosion overpressures? The Pittsburgh Research Laboratory (PRL) of the National Institute for Occupational Safety and Health (NIOSH) undertook a study to identify and evaluate passive measuring devices to monitor and quantify the overpressures associated with such explosions. This work was done in parallel with full-scale explosion experiments for evaluating the strength characteristics of seals used for isolating areas in underground coal mines. Approach Evaluation studies were done in PRL's 20-liter explosion test chamber and in the full-scale Experimental Mine at Lake Lynn Laboratory to evaluate the response and accuracy of various commercially available automobile tire pressure gauges to overpressures generated from gas and dust explosions. The first series of tests was done in the 20-liter chamber, which is used to study the explosibility and inerting of fuel dusts and gases. Data from the tire pressure gauge tests were compared to the pressure-time data obtained from the 20-liter chamber 's traditional electronic strain gauge pressure transducer recorded on a high-speed data acquisition system. To evaluate the tire pressure gauges, the valved inlet (tip) of the candidate pressure gauge was removed and the body of the gauge was cemented with epoxy into a 0.25-in pipe elbow and attached to the outside of the test chamber. A second series of tire gauge evaluation tests was done at Lake Lynn during explosion-resistance testing of seals used in underground coal mines. Full-scale seals (20 ft wide by 8 ft high)were constructed as one wall of a 2,000-ft3 chamber and exposed to a series of methane explosions. Average overpressures ranged from20 to 80 psi. The seals were built with various strength materials ranging from 7 to 48 in thick. The modified tire gauges are attached on the outside of the chamber to a 0.25-in NPT pipe that extends into the chamber (figure 1). The axis of the gauge is mounted at a right angle to the plane of the seal to minimize the coupling of any seal movement to the stem of the gauge that may cause inaccurate readings. The internal explosion pressure history is recorded with a strain gauge pressure transducer mounted inside the chamber. Methane is injected into the chamber, mixed with air, and ignited with an electric spark located at the geometric center of the chamber. Maximum explosion overpressures are recorded and compared with the tire gauge pressure.

Jun 1, 2001

By Connie S. Musulin

The Bureau of Mines conducted an experiment at Exxon Mineral Co.'s Buffalo Shaft Operation to determine the time required for radon concentrations to return to a base average after fan shutdowns. Shutdown times ranging from 5 min to 16 hr were evaluated. An equation was derived to calculate a ratio that determines the time required for the radon concentration to return to the average level that existed in the mine prior to shutdown. For fan shutdowns of 15 min or more, underground personnel should be evacuated to areas with natural downcast ventilation. For shutdowns of less than 1 hr, personnel should not return to the working area until the elapsed time is four times the shutdown, or until the working area is resampled and found safe. If the mine is not in production during weekends, the downcast fans can be turned off .from midnight Friday until 4 p.m. Sunday, and the radon daughter concentration should be below 1 WL throughout the mine by the start of the shift Monday. This fan shutdown would conserve energy and save the mining company an estimated $21,000 each year.

Jan 1, 1982

By James Paone

The Bureau of Mines conducted laboratory drillability studies on nine rock types using two mining-type percussive drills. Percussive-bit action was simulated by dropping a known weight on a rock sample to obtain a coefficient of rock strength for each rock drilled. While no single physical property of a rock is completely satisfactory as a predictor of penetration rate, coefficient of rock strength showed a better correlation with penetration rate than did other physical properties. Results also indicate that over the range of energies investigated, energy per unit volume in a given rock is independent of blow energy. A drillability index for the percussive system is proposed that utilizes the coefficient of rock strength test to determine energy per unit volume for a given rock which, along with the work rate of a given drill and the bit diameter, is used to predict the penetration rate as shown in the following equation: [R = 4P pD2 E, where R = penetration rate, in/min, P = work rate, in lb/min, D = bit diameter, in, and Ev = energy required to produce a given volume of rock, in lb/in3.] Laboratory tests indicate this method's potential as a simple and reasonably accurate method of predicting penetration rates with any percussive drill and bit combination.

Jan 1, 1969

By M. J. Ferrante

The Bureau of Mines determined the enthalpies of Ni3S2 relative to 298.15 K to provide new thermodynamic data for advancement of mineral science and technology. Enthalpies were measured with a copper-block calorimeter from 298.15 to 1,197 K. A solid-solid transition was found at 834±1 K, with an isothermal heat absorption of 13.32 kcal/mol. The temperature of this solid-solid transition was accurately measured by differential scanning calorimetry. Because Ni3S2 does not melt congruently, the heat of fusion of 4.70 kcal/mol was obtained by extrapolation of enthalpy measurements from the solid and liquid phases to approximately 1,064 K. Tabulated values are given for the relative standard enthalpy, heat capacity, entropy, and Gibbs energy function between 298.15 and 1,800 K. Enthalpies are also given in equation form and combined with data from the literature to derive values of standard enthalpies of formation and Gibbs energies of formation. Similar calculations were made for the reaction of crystalline and liquid nickel with gaseous diatomic sulfur for Ni3S-2(c, l).

Jan 1, 1982

By M. J. Spendlove, P. P. Zapponi

"INTRODUCTION In carbothermic processes for the production of magnesium, magnesium oxide is reduced by carbon according to the following equation:(1) MgO + C = Mg(g) + CO.The reaction is virtually complete at temperatures above 2,000° C. but reverses rapidly at somewhat lower temperatures. To produce magnesium by this reaction, therefore, it is necessary to cool the gas very rapidly to a temperature at which the rate of the reverse reaction becomes negligible. Several media for quenching the gas have been proposed, among which are hydrogen, natural gas, liquid hydrocarbons, and molten metals of low melting point.The results of a preliminary investigation on the use of molten lead as the quenching medium are summarized in this report. The work was done in 1941, when the threat of war made it imperative to investigate every process that offered possibilities for rapid expansion of domestic production of magnesium. Although the results were encouraging, other processes appeared to offer better prospects for immediate wartime development, so the work was not continued. Shortly before the investigation was completed, several patents on the use of low-melting metals for absorption of magnesium vapors appeared, 4/"

Jun 1, 1947