Search Documents

By D. J. Bauer

Solvent extraction separation of light group rare-earth elements in a quaternary ammonium compound-chelating agent system was demonstrated in single-stage studies, Typical separation factor values obtained were 93 for lanthanum-praseodymium, 5.4 for praseodymium-neodymium, and 11.6 for neodymium-samarium. These values are significantly higher than those obtained using organophosphate extractants. Further studies in a 20-stage countercurrent mixer-settler resulted in the production of 99 percent lanthanum (oxide basis) at 96-percent recovery. Subsequently, 88 percent of the neodymium with a purity of 92 percent was recovered in the raffinate.

Jan 1, 1971

1. Data from the Mine Safety and Health Administration (MSHA) indicate that a total of 44,015 employees worked in underground mining locations in 2003, corresponding to 44,778 full-time equivalent (FTE) workers. • Ninety percent of underground employees (n = 39,735) were mine operator employees. • Contractors comprised 10% of all underground mining employees (n = 4,280) and comprised only 5.8% of all underground FTEs. • The majority of underground employees worked for coal operators (73.0%; n = 32,130).

Feb 1, 2005

By Barbara Fotta

According to the Bureau of Labor Statistics (BLS), workforce estimates of median age suggest that the median age of the mining workforce, which has been experiencing overall declines in numbers of employees, is rising more rapidly than for the overall U.S. civilian labor force. In the absence of detailed demographic data for the mining industry, the current study uses injury and illness data reported to the Mine Safety and Health Administration (MSHA) to examine differences, over time and by commodity, in the proportions of injured or ill workers aged 45 years and older. These data indicate that from 1988 to 1998, the percentage of injured or ill older workers (aged 45 years and older) have been steadily increasing. The most notable increase occurred at coal mining operations where the proportion of injured/ill older workers increased from 24 to 44 percent. A more detailed breakdown of the industry by commodity for 1998 showed the highest proportions of older injured/ill workers (over 40%) occurring in coal, iron ore, alumina mills, cement, and trona operations. In coal operations, as the employment size of the mine operation increased, so did its proportion of older injured/ill workers. Also, higher proportions of older injured/ill workers were observed at surface coal work locations than at underground locations. The distribution of older injured/ill miners by occupation for several select commodities shows the highest proportions for supervisors, electricians, mechanics, and surface equipment operators, and the lowest proportions for surface laborers and for underground coal roof bolters and scoop operators. With few exceptions, older injured workers have the highest median number of days lost per injury when examined by type of mining operation and by occupation. Given the high proportions of older injured or ill workers in many sectors of the mining industry, health and safety programs must consider the physiological changes associated with aging when evaluating job tasks and the working environment.

Jan 1, 2004

Crosson and Peters treat the errors that result in miner location due to errors in the overburden earth model used for computing location. A parallel effort by J. Powell of PMSRC is discussed here, where the location method used is that of the Westinghouse location program - "Miner". This location program was tested by Powell by using arrival times generated from the overburden earth model of Table l* rounded to the nearest millisecond. Location computations were then made using 3 geophones at a time. The average location is tabulated for all geophone triplets except when 3 geophones are in line. Geophone arrays were as shown in Tables 2 and 3. The manner in which the test was done is illustrated in Figure 1. I. SUMMARY OF RESULTS The arrival time differences, based on the Table 1 earth model, together with geophone locations based on the array geometries of Tables 2 and 3, were entered into the computer, together with a stated depth of 700 feet and an estimated overburden seismic velocity of 10,000 feet per second. These parameter values were processed by the location program - "Miner". Figure 2 illustrates the interpretation of the plots and data. The tabular data and plots of Table 4 and Figures 3, 4, and 5 illustrate the location error results obtained. These plots indicate that for sources within the array, the errors are considerably less than the measured errors obtained during field tests of the present location system. The possible reasons for this discrepancy are noted in Part Eight (Earth Models).

Jan 1, 1974

Over and above the technical support arid consulting work described in the preceding Parts of this Volume, ADL staff also provided a wide range of additional technical assistance to the Bureau on an ad hoc basis over the course of the contract, and particularly in 1973. Some of these assignments were on tasks that temporarily assumed a high priority at PMSRC, requiring a fast response, while others were more suited to conventional schedules but on communication and location topics less directly related to those in the preceding Parts. Chapter I briefly describes some of the diverse short-term assignments while Chapters I1through V treat assignments on the other topics. I SHORT-TEXM ASSIGNMENTS A sampling of short-term, fast-response assignments undertaken on mine communications and miner location for PMSRC during 1973 are given below. These assignments included technical reviews, discussions and recommendations related to the theory, experimental data, designs, and hardware implementation of experimental CW and pulse miner location EM transmitters; preparation of technical performance specifications for a miniaturized preproduction prototype CW electromagnetic location transmitter; review of specifications for a seismic signal detection experimental study; participation in technical discussions and experiments with PMSRC and equipment suppliers regarding the UHF radio/radiax-cable communications installation in the Bruceton mine; participation in an informal conference to discuss mine communication and monitoring needs and preferences with representatives of the Bureau, mine operators, and equipment manufacturers; participation in technical discussions with representatives of a U.S. mine operator and CERCHAR* concerning the characterization of faults on trolley lines and means of improving their rapid detection;** recommendation of simple signal, noise, and ground fault measurements on mine phone lines; review of an inexpensive automatic telephone dialer; preliminary discussions regarding the feasibility of adapting and assembling a collection of available telephone industry carrier equipment for installation and test in an operating coal mine; evaluation of a proposed call alert mine paging system; review of hardware designs and future experiments for a mine communication sled; design critique of a proposed six-channel narrow-band FM voice modem for carrier communication on the mine phone line; preparation of technical performance

Jan 1, 1974

By Ronald D. Hill, Elmore C. Grim

The removal of overburden often exposes pyritic materials (iron disulfide). As shown in equations 1 and 2, the oxidation of this material results in the production of ferrous iron and sulfuric acid. The reaction then proceeds to form ferric hydroxide and more acid, as shown in equations 2 and 4. [ ] Consequently a low pH water is produced (pH 2-4.5). At these pH levels, the heavy metals such as iron, manganese, copper, and zinc are more soluble and enter into the solution to further pollute the water. Water of this type supports only limited water flora, such as acid-tolerant molds and algae; it will not support fish life, destroys and corrodes metal piers, culverts, barges, etc., increases the cost of water treatment for power plants and municipal water supplies, and leaves the water unacceptable for recreational uses. The amount, and rate of acid formation, and the quality of water discharged are a function of the amount and type of pyrite in the overburden and coal, time of exposure, characteristics of the overburden, and amount of available water(l). Crystalline forms of pyritic material are less subject to weathering and oxidation than amorphic forms. Since oxidation by oxygen is the primary reaction during early acid formation, the less time pyritic material is exposed to air, the less acid is formed. Thus, a positive preventative method is to cover pyritic materials as soon as possible with earth, which serves as an oxygen barrier. In terms of mining, this step is accomplished by current reclamation techniques and small open pits.

Jan 1, 1974

By Foster Fraas

In the separation of a component from a mixture , two fractions are obtained , one containing a high - percentage composition of the component and the other a low - percentage composition . The high - percentage fraction is frequently called the concentrate and the low - percentage fraction the tailing . In many separation processes the recovery is not complete , and the composition of the concentrate decreases as the recovery of the component, which is concentrated , increases . It is this particular class of separations to which this paper is confined .

Oct 1, 1942

Heavy liquids have come into use in ore-dressing investigations, as they make possible the separation of an ore into its specific-gravity components. A paper containing a general dissertation on heavy liquids has been written by John D. Sullivan,4 and the practical application of heavy liquids is explained by Box and Crabtree5. Some heavy liquids become discolored after continued use, and the lack of transparency impairs their value. Since they are fairly expensive, reclaiming is desirable. This paper briefly discusses the preparation and care of some of the more common heavy liquids.

Jan 1, 1928

By Richard W. Lewis

Domestic production of greensand (glauconite) increased 15 percent in quantity and 13 percent in value compared with that of 1964. Since only two firms were in operation, statistics on production and sales for the year are not reported in order to avoid disclosure of individual company confidental data. The average annual production for the 5-year period 1961-65 was 4,306 tons valued at $200,200. The material was marketed for use as a soil conditioner and a water softener. An article of mineralogical interest was published concerning the New Zealand glauconites.2

Jan 1, 1966

By F. E. Brantley

Optimum autoclaving conditions were determined for separation of iron and manganese values from pregnant leach liquor produced in extracting manganese from low-grade umber are. The umber was leached with a synthetic anolyte similar to a recycle solution, used in manganese electrolysis cell operations, that had been renewed with ferrous sulfate and sulfuric acid. The equipment used and results obtained are presented for the several conditions employed. The kinetics of the separation were studied. Rate equations were derived for the formation of solid ammonium-manganese sulfate, (NH4)2 Mn2 (S04)3.

Jan 1, 1968

By Oliver Bowles

"On January 15, 1920, a man was killed by falling rock in a limestone quarry in Utah. The quarry was visited by a representative of the Industrial Commission of Utah, and the cause of the accident was carefully determined. The facts concerning this accident, and the Bureau's recommendations are given in some detail in the hope that quarrymen may take steps to avoid dangerous conditions, and thus reduce the liability to accident.The quarry rock face is about 180 feet high, and the ledge is covered with an overburden of 10 to 20 feet of a mixture of soil and boulder. The rock face is not vertical, but slants at an angle of about 45° to 50°, while the stripping face stands at an angle of 70° to 80°, and is flush with the rock face. The conditions are shown in the accompanying figure.The man who was killed was employed in breaking rock at the foot of the quarry wall. The sun had been shining on the stripping face, and probably thawed the ground, thus permitting a boulder weighing about 20 pounds to roll down the slanting face, striking, and almost instantly killing the workman who was working with his back toward the quarry wall."

Feb 1, 1920

By Van E. Shaw

Fusion of an 86-percent euxenite concentrate with ammonium sulfate was investigated by the Bureau of Mines. Reaction for 4 hours at 400° C results in conversion of both the rare-earth elements and the titanium-columbium components to water-soluble compounds. Similar results are obtained with ammonium bisulfate. Stirring the fusion mass decreases the reaction time substantially. Alternatively, treating the fusion product with a 3-hour, 650° C calcining step renders the non-rare-earth constituents insoluble, thereby allowing selective leaching of a pure rare-earth fraction with an overall yield of 97 percent.

Jan 1, 1967

By C. J. Tsai, K. Olson, R. Caldow, B. Cantrell, D. Y. H. Pui

"The amount of new surface generated during fracture of coal and rock has been found to be directly proportional to the amount of energy associated with the fracture. To confirm this and study the relationship between the new surface and dust aerosol formed during fracture the U.S. Bureau of Mines has conducted experiments simulating fracture as it occurs during mining operations. In addition to fracture energy measurements, fragment size distributions were determined over a size range of 0.5 microns to 1 inch. The size measurements accounted for the mass of the original sample. Material studied was Illinois No. 6 coal, coal from the Taggart seam of Virginia, and Berea Sandstone. The experiment employed a chamber to confine sample fracture fragments and a combination of particle measuring systems. Measurement methods included aerodynamic sizing of entrained dust aerosol with optical counting and inertial impaction techniques, physical sizing of non-airborne fragments by sieving, and optical sizing of fragments using optical counting and scanning electron microscopy.Results of the size distribution measurements indicate that a single size distribution law does not adequately describe the entire fragment size distribution. A combination of two size distribution laws, such as the Rosin-Rammler and log-normal distributions, is necessary to describe this size distribution. New surface created by fracture is primarily found 1n particulate between 2 and 50 microns with a mean size of 12 microns. It was also found that the specific energy of fracture can be linearly related to the .concentration of aerosol in this size range.Only a .small fraction, between 0.02 and 0.16 pct, of the dust particles .generated during fracture become airborne. The remainder adhere to the new surface created during fracture. An entrainment fraction, defined for a given particle size is the ratio of the mass of airborne particles to that of the total particles generated in that size range. This experimental entrainment fraction is related to the Van der Waals adhesion force and the electrostatic forces operating during fracture and is used to derive empirical parameters to model these two processes."

Jan 1, 1989

"Minimizing Particle Contamination During Generation of Fresh Dust for Inhalation Studies J. Abraham, MS, Mechanical and Aerospace Engineering, West Virginia University, 1995Correlating Lung Crackle Using Holographic Interferometry Ali Afshari, MS, West Virginia University, 1989Effect of Bit Wear on Dust Generation Mudassar Ahmad, MS, West Virginia University, 1992 The Effect of Surfactants on Suppression of Non-Wettable Particles Ali Alaboyun, MS, Mineral Engineering, The Pennsylvania State University, 1989 Geochemical Characterization of Kerogens, Shales, and Coal Refuse Associated with Allegheny Formation of Cases of Northern West Virginia Dick Andre, MS, West Virginia University, 1987Size and Mass Characterization of Airborne Particulate Matter in Underground Coal Mines Using Diesel-Powered Equipment Indranil R. Bardhan, MEM Report, The Pennsylvania State University, 1992Size and Mass Characterization of Airborne Particulate Matter in Underground Coal Mines Using Diesel-Powered Equipment I. Bardhan, R. V. Ramani, and J.M. Mutmansky, Mining Engineering, The Pennsylvania State University, University Park, PA, Final Report to the U.S. Bureau of Mines, April, 1994Particle Concentrations in a Hazelton Inhalation Chamber Shahram Bavani, MS, West Virginia University, 1985Use and Potential of Lazer Holographic Interferometry and Subsidence Model- Study of an Underground Room and Pillar Mine Richard Begley, MS, West Virginia University, 1984Development of a Mechanistic Model for Prediction of Subsidence in a Longwall Mine Richard Begley, PhD, West Virginia University, 1990Redesign of Micro-Orifice Uniform Deposit Impactor Steve Behm, MS, University of Minnesota, 1991Evaluation of a Two-Phase Spray System for Dust Suppression B. Belle, MS, The Pennsylvania State University, 1996Evaluation of a Two-Phase Spray System for Dust Suppression B. Belle and R.-V. Ramani, The Pennsylvania State University, University Park, PA, Final Report, September 9, 1996A Fracture Mechanics Study of Crack Propagation Mechanism in Coal: The Mechanics of Fine Fragment Formation Z.T. Bieniawski and R. Karl Zipf, Jr., Mining Engineering Department, The Pennsylvania State University, University Park, PA. Final Report, October l, 1988A Mathematical Model for the Prediction of Ambient Dust Concentrations in Mine Atmospheres R. Bhaskar, MS, Mining Engineering and Operations Research, The Pennsylvania State University, 1984Spatial and Temporal Behavior of Dust in Mines-Theoretical and Experimental Studies –R. Bhaskar, PhD, Mining Engineering, The Pennsylvania State University, 1987"

Jan 1, 1998

By Warren E. Morrison

The continuing high-level performance of the domestic mineral and mineral fuels industries during 1966 was sustained by the longest business upturn in the Nation's history. Spurred by consumer demand at home and the defense production requirements of the Viet-Nam war, the rising trend of economic activity during the year was reflected in the upward movements of the major economic indicators. At yearend the gross national product (GNP), representing the value of all goods and services produced, stood at $740 billion, $58 billion greater than in 1965. Corrected for price changes, the real value of GNP in terms of 1958 dollars was $648 billion and represented an annual increase in economic activity of 5.4 percent. Some 74 million persons were employed during the year out of a total population of 196.8 million, while unemployment fell below 4 percent. The Federal Reserve Index of Industrial Production averaged 156 for 1966, up 13 points from the previous year. However a jarring note in the 1966 expansion, and one which affected the mineral industries in particular, was the increasing pressure on prices and the threat of inflation. From 1961-65 economic growth was facilitated by relatively stable wages and prices and only mild inflation. During the period average wholesale prices hardly moved while average consumer prices rose only about I percent per year. But this long run of relative price stability ended during 1966 when consumer prices rose 2.9 percent and wholesale prices were up 3.2 percent from the previous year.

Jan 1, 1967

By R. K. Koch

The vapor pressures of liquid molybdenum and liquid zirconium were determined by the Langmuir free-evaporation method. An electron-beam furnace with a water-cooled copper crucible was used for melting. Temperature was measured with a two-color ratio pyrometer. The vapor-pressure data led to the following equations: [log p (atm) = 5.429 - 28,380 T for liquid molybdenum in the range 2,890° to 2,990° K, and log p (atm) = 6.521 - 30,940 T for liquid zirconium in the range 2,229° to 2,795° K.] Third-law evaluations of each data set gave mean heats of sublimation (298.15° K) of 157.6 ± 1.8 kcal/mole and 148.4 ± 2.4 kcal/mole for molybdenum and zirconium, respectively, where the uncertainties are two standard devia¬tions. Second-law standard heats of sublimation determined from sigma plots and tabulated enthalpies were 143.5 ± 2.7 kcal/mole and 149.2 ± 3.8 kcal/mole for molybdenum and zirconium, respectively. The better agreement in heats of sublimation for zirconium is attributed to the 566° K temperature range studied which permitted a more accurate definition of the vapor pressure curve than could be obtained from the 100° K span for molybdenum. This supposition was verified by making a sigma-prime plot which utilized solid vapor pressure data for molybdenum to extend the evaluation range by 800° K. This gave a standard heat of sublimation of 155.2 ± 1.6 kcal/mole which is in good agree¬ment with the third-law value. The plot also gave a standard entropy of sublimation (298.15° K) of 35.73 ± 0.48 eu.

Jan 1, 1968

By J. L. Ellenberger

The National Institute for Occupational Safety and Health (NIOSH) has continued the research role of the former US Bureau of Mines (USBM) to engineer techniques that will reduce the hazards in the mining workplace associated with coal bumps. Recent research focused on a longwall coal mine in Utah with overburden greater than 750 m (2,500 ft) containing several massive sandstone units. The primary field instrumentation at the site was three-dimensional, full waveform, autonomous microseismic arrays placed underground and on the surface in order to surround the active multi-panel longwall district. The purpose of these arrays was to help investigate the strata mechanics associated with the redistribution of stress and the associated gob formation of the longwall. Specifically, the seismic arrays were used to determine the timing and location of the failure in the strata surrounding the active mining. Overall 13,000 seismic events were detected and located with on-site processing during the five months the panel was being mined, including a magnitude (ML) 4.2 event. Of these, a smaller subset of 5,000 well-located events was selected during post-processing to form a consistent data set for analysis in this paper. From this data set, it was observed that the seismic events generally occurred in advance of the longwall face, both above and below the panel, consistent with failure of the strata in the forward stress abutment zone. Also, the occurrence of the ML 4.2 seismic event within 150-180 m (500-600 ft) of a deep cover longwall face with no associated bump caused a re-evaluation of the nature of the connection between seismic activity and coal bumps.

Jan 1, 2002

By W. H. Frederic, A. C. Fieldner, W. A. Selvig

"Low-rank coals have a pronounced tendency to disintegrate or ""slack” when alternately dried, and wetted by exposure to the weather. The more readily a coal slacks the greater is its tendency to ignite spontaneously and the more care must be used in its shipment and storage. Lignite slacks very readily when exposed to the weather. Slacking trouble is also experienced in shipping and storing subbituminous coal, but not to the same extent as with lignite. As a rule, bituminous coals are only slightly affected by weathering and in general may be classified as nonslacking coals. The slacking tendency of subbituminous coal is one of the characteristics that is used to distinguish it from bituminous coal. An accelerated laboratory method of test was developed to measure such slacking tendencies. This method was applied to a number of coals, principally from the State of Washington, and the method and the results obtained are given herein.Helpful information concerning slacking tendencies of coal was received from Marius R. Campbell, senior geologist U. S. Geological Survey.Coals that slack readily contain relatively large amounts of moisture. When exposed to the weather such coals lore moisture rapidly. As the coal loses moisture at the surface there is a gradual drift of moisture from the interior of the piece to the surface. If the loss of moisture at the surface proceeds at a faster rate than it is replaced by moisture from the interior of the coal piece, there undoubtedly in greater shrinkage of the coal at the surface as tom-pared to the interior of the piece and stressed are generated in the surface coal.These stresses in the surface coal cause it to crack and disintegrate.Likewise, when the air-dried coal is wetted by rain, the exposed surface of the coal pieces gain moisture more rapidly than the interior of the piece, causing greater expansion in the surface coal and the coal breaks down further. As this process of air drying and wetting is continued when the coal is exposed to the weather, the slacking proceeds and the exposed lumps of coal may disintegrate completely."

Nov 1, 1930

By Bruce Cantrell, K. L. Rubow

"INTRODOCTIONMeasurement of the contribution of diesel exhaust to respirable aerosol in mine environments has become increasingly important because of current concerns over the occupational health effects resulting from exposure to diesel emissions. In response to this, the U.S. Bureau of Mines is developing and evaluating new sampling methods for measuring diesel aerosol in underground mines. Two such techniques are being studied by the Bureau, size selective sampling and Chemical Mass Balance (CMB) modeling. These techniques use measurable physical or chemical characteristics of a mine aerosol sample to infer the amount of diesel particulate material contained in the sample.Size selective sampling is being adapted for measurement of diesel aerosol by the Particle Technology Laboratory (PTL) of the University of Minnesota under sponsorship by the Bureau. 1 It is based on the premise that diesel and mineral dust aerosol can be physically separated by size and collected during sampling using inertial impaction. An independent effort by the National Institute for Occupational Safety and Health to develop a size selective sampling technique was also sponsored by the Bureau.The second technique, CMB modeling, is being developed by the Bureau as an alternative measurement technique to referee the results obtained using size selective sampling.3 It compares measured trace element ""finger prints"" of aerosol sources with similar profiles of mine aerosol samples. From these, the portions of the sample contributed by each source can be determined. Results of these investigations in underground coal mines have confirmed that diesel and coal dust aerosol are of different size and can be measured separately using size selective sampling techniques.A major difference in diesel usage among underground mines is the requirement for exhaust gas cooling systems in coal and gassy noncoal mines. Nongassy mines usually employ limited exhaust conditioning in the form of catalytic converters, which have limited effect on primary exhaust particulate. The cooling system in most general use in gassy mines is the water scrubber. This device has little effect on most of the gases but removes particulate material from the exhaust. 5 Because of this, exhaust aerosol characteristics in nongassy mines are expected to be different. To see if size selective sampling techniques can be used in such mines, the Bureau and the University of Minnesota conducted a second study in three metal and nonmetal mines, two nongassy and one rated as gassy."

Jan 1, 1990

The Ringelmann Smoke Chart fulfills an important need in smoke abatement work and in certain problems in the combustion of fuels. A knowledge of its history and method of preparation is, therefore, of interest to many. Since instructions on its use are not shown on the recent edition of the chart, those included in this revision of the previous Bureau of Mines publication now are a necessary complement to the chart, More detail regarding the use of the chart is included than was given in the earlier version.

Jan 1, 1967