Search Documents

By L. D. Tracy

"Introduction In the course of the investigations by the Bureau of Mines into the various causes of coal-mine explosions, the fact that several gas explosions had occurred during or very soon after a mine was being un-watered, attracted the attention of the Bureau's engineers. The apparent coincidence was so marked that there appears to be an extra hazard present, whenever water, which has been standing against the face of the coal for some time, is suddenly removed either by natural drainage or by mechanical means.Actual Occurrences Case 1. - A typical illustration of this hazard is shown in a gas explosion which occurred in a mine in Central Pennsylvania. Four main entries, 50 feet apart with an average grade of 6 per cent, had been driven with the dip of the coal, and from these mains 7 pairs of entries, at intervals of 800 feet, had been turned at such an angle that their grade was slightly rising. Prom these latter pairs of entries, rooms were turned practically at right angles.The main entries had been driven for 4,500 feet and at the face there was 400 feet of cover. As far as could be observed, the roof was of sandstone and the floor of clay.The coal bed being mined was the Lower Kittanning, which has a thickness of about 4 feet. A typical analysis of the coal in that section is as follows:"

Oct 1, 1924

1. In 2002, a total of 4,311 stone mining operations reported employment to the Mine Safety and Health Administration (MSHA). The major industrial classifications in stone mining are dimension stone (used for construction purposes), crushed and broken stone (aggregates), cement, and lime. Stone mines comprised 29.7% of all mining operations. • Mines producing crushed and broken stone (n = 3,372) comprised 78.2% of all stone mining operations.

Jan 1, 2004

By Brian L. Quick

Problem: The National Institute for Occupational Safety and Health's [NIOSH] National Occupational Research Agenda (DHHS Publication No. 96 115) reports that approximately 50% of miners will experience hearing loss by age 50, compared to only 9% of the general population. The present investigation examines three antecedents believed to be associated with miner's use of hearing protection. Method: A posttest delayed posttest control group field research design was employed to assess antecedents toward wearing hearing protection. Results: Following the initial posttest, miners' attitudes and subjective norms were antecedents to intentions to wear hearing protection devices. Also, intentions toward wearing hearing protection predicted hearing protection behaviors. Approximately six weeks later, miners' attitudes and perceived behavioral control were each significant predictors of intentions to wear hearing protection and again, intentions were positively associated with hearing protection behaviors. Impact on Industry: Our results indicate that appeals to normative influences may be the most effective antecedent to employ when persuading coal miners to wear hearing protection. However, messages designed to impact attitudes and perceived behavioral control were also effective.

Jan 1, 2008

"INTRODUCTIONMany of the facilities and much of the equipment available to the Generic Mineral Technology Center for Respirable Dust are highly specialized and therefore, unique to the universities associated with the Center as illustrated in FIGURES 30 through 39.For example, a sample bank of 1300 U.S. coal specimens housed in the Coal Research Section, Deike Building of The Pennsylvania State University has been characterized for physical, elemental, mineralogical and maceral compositions. The results of this research have been used to initiate a study of the relationship between pneumoconioses and coal properties. Selected samples from this bank have been used in animal (primate) studies at the Milton S. Hershey (Penn State) and West Virginia University Medical Centers. These laboratory facilities for research in the medical and biological disciplines is state-of-the-art and includes a primate colony where dust research is currently underway. The Materials Research Laboratory and the Rock Mechanics Laboratory at PSU, and the Mechanical Systems Design and Control Laboratory, the Rock Mechanics Laboratory and the Mine Electronic System Laboratory at WVU are equipped for fundamental research on dust generation and characterization. While the majority of respirable dust research projects fall into these two categories, dust generation and characterization and interaction of dust and lung, there are other laboratory facilities available to the Center which are unparalleled in the type of equipment and expert personnel that they contribute to the program. The Mine Particle Laboratory located at the University of Minnesota and the Diesel Engine Laboratory at Michigan Technological University are examples. They house equipment and instrumentation that is unique to these facilities. much of it having been developed specifically for dust research by the research scientists there. The dust collection equipment and the fine particles measurement, characterization and analysis apparatus are essential to research in the areas of dust collection, particle characterization and diesel particulates. In addition to university laboratories, the research facilities of the National Institute for Occupational Safety and Health (NIOSH) are available to the Center through its relationship With West Virginia University."

Aug 31, 1989

By L. C. IlsLey, E. J. Gleim

The extensive use of pulverized coal for fuel in industrial plants has brought to the front again a question that heretofore has been considered only a mining problem, namely, " Can coal dust be ignited by an electric arc ? " If it can be so imited, the next logical query is , "under what conditions can such ignition occur ? " In view of the new problems relating to pulverized coal installations , and because of occasional mine disasters attributed to ignition of coal dust by electric arcs , it seems advisable to review the work done by Thornton and Bowden with electric flashes in coal dust , and to report two preliminary investigations conducted by the Bureau of Mines .

Jun 1, 1922

By Walter R. Storms

The Iron Mountain tungsten deposits first were visited by a field party of the Federal Geological Survey in May 1942 while beryllium deposits in that district' were being examined . Later they were examined by F. A. Rutledge , an engineer of the Bureau of Mines , and an exploration project was recommended , work upon which began in March 1943 and was terminated in April 1943 after intensive trenching and sampling had been completed .

Mar 1, 1947

By McHenry Mosier

A skull breaker has demonstrated its advantages for secondary breaking in a limestone quarry by entirely displacing secondary blasting . It has reduced safety hazards to workmen, increased the number of quarry operating days , and has lowered mining costs by 2.7 cents a ton. It is believed that the application of the skull breaker can be made economically advantageous in the surface mining of other commoditics .

Aug 1, 1948

By Hon-Chung Ko

This Bureau of Mines report provides the enthalpies of formation of cupric bromide and cuprous bromide as determined by hydrochloric and hydro-bromic acid solution calorimetry. At 298.15 K, the values are -33.10 ± 0.4 kcal/mole for CuBr2, and -25.24 ± 0.25 kcal/mole for CuBr.

Jan 1, 1975

By F. W. Smith

This paper is based largely on a study of experimental data obtained by the Bureau of Mines in its comprehensive 25-year survey of the carbonizing properties of American coals. Although the Bureau was interested in and conducted carbonization research-from time to time ever since it was organized in 1910 (1),4/ no systematic studies of the coke-, gas-, and byproduct-making properties of American coals were undertaken until 1927, when the American Gas Association appointed an advisory committee (2) to cooperate with the Bureau in developing equipment and techniques to obtain-data for the accurate assessment of the behavior of coals on carbonization. It was found, in general, that small-scale laboratory tests were unsuitable for the complete evaluation of the coking properties of coal; hence, larger pilot-plant-scale equipment was designed and used (3). It was decided that the scale of the test should be large enough to determine both the yield and quality of the products and yet small enough to maintain adequate control of the process variables (4). These considerations led to development of a carbonizing retort and furnace-of 80 to 200 pounds of coal capacity, suitable for operation at various temperatures up to 1,100° C. (2,0120 F.) and equipment for recovery and measurement of gas and byproducts. This apparatus and the standardized procedure for its operation became known as the Bureau of Mines-American Gas Association (EM-AGA) method or retort (5).

Jan 1, 1955

By Janke L. W. Jolly

Owing to an upsurge in export earnings. Cameroon made substantial economic Progress in 1978 and 1979. With a real growth estimated at 6%, the gross domestic product (GDP) for 1979 surpassed $5 billion.2 Crude petroleum production was providing a new potential in 1978 and 1979 for achieving national self-sufficiency. Among other benefits, crude petroleum exports were helping to offset the escalating costs of refined petroleum imports and to reduce the 14% to 17% annual rate of inflation. Over the 4 years prior to 1978, Cameroon's petroleum imports increased by 12.1% in volume annually, while the import cost increased by 24.5% annually to about $105 million. Total export earnings for 1978 were $805 million,3 to which crude petroleum contributed $25.3 million and crude aluminum product exports contributed $25.9 million. Petroleum exports had increased to about $240 million in 1979 and were in third place after coffee and cacao. Total imports for 1978 were valued at nearly $1 billion. The volume of petroleum imports decreased in 1979 to 552,000 tons, compared with 622,000 tons in 1978. The European Economic Community (EEC) countries purchased over 75% of total Cameroonian exports and provided most of the Nation's imports. The United States purchased $12.4 million in petroleum exports from Cameroon in 1978. Domestic consumption of aluminum metal from imported Guinean alumina continued. to grow; thus exports of this metal to France (valued at $2 million in 1978) and Japan

Jan 1, 1981

By Douglas Talley

This report describes a 4-inch diameter borehole probe which contains a low light level TV camera, magnetic compass, light illumination source, bottom/water detector sensor and a pointing angle sensor. The camera viewing angle is at a right angle to the probe's body. All data from the sensor is multiplexed into the closed circuit camera video for transmission on a single 50 ohm coaxial cable to a surface control unit. Likewise control of the probe's power, zoom lens, focus, panning and aperture is accomplished via a down-link multiplexed on the same cable.

Jan 9, 1984

By Ted C. Briggs

Twenty-two compressibility runs were made with helium over the temperature range -5° to 80° C and at pressures to 800 atmospheres. A Burnett apparatus was used. Data from the runs were fitted to a fourth degree polynomial equation of state in the pressure and a weighting factor of Pr-3/4 was used. All data for a particular isotherm were treated simultaneously. A temperature function was found to represent the parameters B and C. Compressibility factors determined by this investigation are believed to be accurate to better than 0.05 percent.

Jan 1, 1970

By A. L. Engel

Simple treatment methods, employing the least possible equipment, can sometimes be established for marginal ores and economical results achieved. In continuation of a long-established part of the hydrometallurgical and ore-dressing program of the Reno Station of the Bureau of Mines, typical ores from newly discovered or recently explored mining districts have been investigated. The purpose of such investigations is to encourage the search for and development of mineral resources and particularly to assist in the economical exploitation of low-grade and marginal ores, as well as the conservation and recovery of values in products from former operations that were discarded because of past inability to treat them economically. Several of these investigations have been limited to preliminary tests of samples from prospecting operations, whereas some involved samples of old dumps or tailings piles. The test, work in these cases was not extensive enough to warrant publication as individual reports, but is of considerable interest inasmuch as it indicates the possibilities as well as the limitations of treating the respective materials; and because, inasmuch as the samples were representative of the districts from which they were obtained, this in-formation should be helpful in the future development of these districts. The present report is a compilation of results of brief preliminary tests on oxide ores only, which contained gold and silver and in some cases base metals. The methods of treatment used include gravity concentration, amalgamation, flotation, and cyanidation. For the most part, only standard laboratory procedures were employed. No attempts were made to develop new methods for the low-grade refractory ores in this group of samples if simple treatment was not successful, as the stage of development of the properties did not warrant extensive experimentation on the samples submitted.

Jan 1, 1951

By E. P. Youngman

The basic mining law of French Morocco is the Edict of 1914, "Danir of Jamary 19, 1914, for the Regulation of Mineral Prospecting and Exploitation in the Zone of the French Protectorate of the Cherifien Empire," which, as the preamble states, was promulgated at the instance of the Director General of Public Works, in consideration of the fact that mines constitute one of the sources of wealth of the Empire. According to a consular report, dated May 18, 1923, by Bradford, men- tioned above, the mining industry of that country, aside from the exploitation of the extensive phosphate deposits, can scarcely be said to exist, but the potential field for mining is promising. However, no large-scale exploitation of the mineral wealth of French Morocco can be hoped for until there is complete pacification of large areas that are still in an unsubdued state or until adequate transportation facilities, scientific prospecting, and large investments of cap- ital are assured. An edict in 1920 (Dahir of January 27, 1920) modified the law mentioned above by declaring the prospecting for and the exploitation of phosphates to be exclusively reserved to the Government. The Dahir o. August 7, 1920, announced the creation of the Cherifien Phosphate Office (Office. Cherifien des Phosphates), a State monopoly charged with the exploration, management, and exploitation of the phosphates of Morocco.

May 1, 1930

By H. C. George

This report presents a comprehensive tabulation of lifting cost data collected from oil companies in many different fields. These data were collected during the writer's studies of surface equipment and methods of pumping oil wells, in practically all of the important oil fields in the United States and are based on average operating conditions at 57 groups of properties with a total of 4,497 producing wells. Although lifting cost is only a part of the total cost of producing oil, it nevertheless gives a representative cost figure for purposes of comparison.

Jan 1, 1923

By H. A. Tucker

This Bureau of Mines investigation was conducted to determine the appropriate quantities of rare-earth methals (REM) in the form of silicides to add to an alloy steel for the purpose of increasing toughness and ductility. The work was conducted in a vacuum induction furnace with the rare-earth additions required to deoxidize and desulfurize a simulated basic oxygen furnace (BOF) vacuum-degassed steel initially containing 0.013 to 0.016 percent sulfur. The product proved to be as good or better than the best basic electric furnace steel of the same composition made by the steel industry. Twenty-three experimental heats of 5 Ni-Cr-Mo-V steel were made, cast into 50-1b ingots, and hot-worked in a press and a rolling mill to ½ inch plates which were then heat-treated to 130/150 ksi4 yield strength. Impact and tension tests showed that the addition of 0.025 to 0.100 percent, or ½ to 2 lb per ton, respectively, of rare-earth metals when compounded with silicon were appropriate for increasing toughness and ductility. These quantities resulted in retained cerium contents between 0.014 to 0.025 percent, and increased the Charpy V-notch energy absorption and the percent reduction of area significantly as compared with base heats at the same sulfur content levels. All the test heats, including those with additions of REH of as much as 4 lb/ton, had greater Charpy V-notch energy absorption values than the base composition could have developed at the starting sulfur range of 0.013-0.016 wt pct.

Jan 1, 1968

By J. M. Stuve

Heat of solution measurements of high-purity neodymium metal and neodymium trichloride (NdCls) in 4.360 molal hydrochloric acid (HCI) were used to determine the standard heat of formation (6EPr) of NdCls? From solution data obtained, the heat of formation of NdCls (c) was computed as -248,970 ±260 cal/mole at 298.150 K.

Jan 1, 1965

By J. M. Stuve

Calorimetric data for the dissolution of scandium sesquioxide and scandium trichloride in 4.360 molal hydrochloric acid were used to evaluate the standard heat of formation of ScCl3(c). The heat of reaction for Sc(c) + 1.5Cl2(g) = ScCl3(c) at 298.15° K was computed as -225,440 ±340 cal/mole.

Jan 1, 1965

By H. C. Ko

As part of the Bureau of Mines effort to provide thermodynamic data for the advancement of mineral technology, the standard enthalpies of formation for ZnO?2ZnSO4 and COS04-6H20 were determined by HC1 acid solution calorimetry. The values are -550.31 ±0.28 and -641.33 ±0.15 kcal/mot, respectively.

Jan 1, 1982

By Michael R. Grubbs

The Bureau of Mines is currently developing methods for reclaiming the metal and mineral values contained in unburned urban refuse. One important phase of this research deals with recovering Mastic from shredded refuse using in electrodynamic separation process. The results of this study have indicated that mixed plastic concentrates analyzing 99.4 percent plastic can be consistently recovered from the light material fraction of shredded refuse, leaving a mixed paper traction analyzing 99.9 percent paper. Recovery of the plastic exceeds 99 percent.

Jan 1, 1972