Search Documents

By Glenn C. Reed

This report is one of a series describing mineral investigations within the Missouri River Basin in Montana. The primary purposed of these investigations is to provide information to agencies of the Department of the Interior and others concerned with the planning of Federal power developments in the basin. This report is limited in score to consideration of mineral deposits of presumed inventory value within Gallatin County, Mont. The field investigations were made during the fall of 1948.

Jan 1, 1951

By E. C. Lane

Although motor gasoline marketed in the United States in January of this year was, on the average, slightly more volatile than that sold in January 1925, the improvement in quality is too small to be of importance. In other words, there is no evidence that any radical change in the quality of gasoline is being made at the present time. During the past six years the Bureau of Mines has made semi-annual surveys of the gasoline marketed in the United States, the survey just completed being the thirteenth in the series. The cities in which samples have been collected have been chosen as representative of the more important marketing territories as it is obviously impracticable to obtain a sample of every gasoline sold in the entire country.

Jan 1, 1926

By T. A. Evans

The Bureau of Mines conducted a Laboratory and pilot-plant investigation of the flotation of iron sulfides from zinc-lead mill tailings near Platteville, in south-western Wisconsin, at the North Central Experiment Station, Minneapolis, Minn. The procedures used and the results obtained in this investigation are described in this report. Samples for laboratory tests were obtained from each mill in the district, namely, Calumet & Hecla, Inc., Eagle-Picher Co., Vinegar Hill Zinc Co., and Tri-State Zinc, Inc. The sample fat pilot-plant work was obtained from the Davis Mining Enterprises mill.

Jan 1, 1957

By J. A. Pile, Virgil Miller, R. G. Peterson, F. B. Petermann

"INTRODUCTION As virtually no published data are available on the sintering of fine, minus-100-mesh, ferrograde manganese ores, it is most opportune to present data on the amenability of various fine ores and mill products to the sintering process. These data cover the sintering or nodulizing of finely crushed, high-grade pyrolusite and rhodochrosite ores, sintering of manganese carbonate flotation concentrate, sintering or nodulizing the calcine from the deleading of a manganese oxide flotation concentrate, and sintering the calcines made in a Herreshoff furnace from the treatment of manganese sulfate products.If finely sized products are to be smelted in the present electric or blast ferromanganese furnaces, they must be sintered or nodulized. The only specification as to the size of the sintered or nodulized product is that it must pass a 6-inch screen and not contain over 1t-1/2 percent minus 20-mesh material. The minimum-maximum size has not been established. Undoubtedly this opti mum size will be set by the ferromanganese industry when ample quantities of manganese oxide sinters have been smelted."

Mar 1, 1942

By D. A. Reynolds, J. D. Davis

"This work was begun in l928, with the cooperation of the American, Gas Association, and the Association contributed financial aid for that year and for the 4 years following. In 1933 financial aid was discontinued, but the Advisory Committee, under the able, Chairmanship of J. S. Haug, has continued to function through the years to the present date. Mr. Haug's annual reports have been published in the Proceedings of the American Gas Association. The purpose of this paper is to bring the index of coals tested by the Bureau of Mines-American Gas Association (EM-AGA) method up to date, to discuss development of auxiliary tests, and to outiline the uses to which the methods have been put in promoting the war effort.COALS TESTEDThe test methods developed with the advice of the Advisory Committee had been applied to 66 coals up to 1942, and an index giving the serial number, origin, and analyses of these coals was published as Bureau of Mines Technical Paper 637. Since this paper was published, 20 additional coals have been tested; the source and analyses of these coals are given in table 1. The table also refers to publications that have been issued. Complete series of tests at high, medium, and low temperatures,have been made on most of these coals, and blending tests with 20 and 30 30 percent of low-volatile coals have also been made at 900°C.; however a few low- and medium-volatile coals (60, 70, 74, 79, and 80) were bested,at high temperatures only. Those coals were mined in eastern Oklahoma and western Arkansas. The test work included low- and high-temperature assay tests, petrorraphic analyses, and plasticity tests since its inception; and for the last 20 coals of the series, expansion and oxidation tests have been made where applicable."

Jun 1, 1944

By Oliver Bowles

The United States has never attained importance as a producer of asbestos, the domestic output being only 1 to 3 percent of the quantity required to supply raw material for its extensive asbestos-product manu- facturing industries. Production is centered in four principal countries-- Canada, Rhodesia, Union of South Africa, and the Soviet Union. Since asbestos first became an important commercial commodity the Province of Quebec, Canada, has led in tonnage produced, but a large proportion of the output of this province is shorter, nonspinning grades. Since 1916 the Union of South Africa and Rhodesia have become increasingly important as sources of the higher-grade spinning fibers. Before the World War Russia ranked next to Canada as a producer of asbestos, but during the revolution- ary period the industry in that country was almost at a standstill. In 1926, however, activity was revived, and each year since then production and exports have increased greatly. Minor quantities of asbestos are produced in Cyprus; Australia, Finland, and several other countries. Chrysotile is the leading product in all the producing countries, but substantial quantities of both blue (crocidolite) and brown (amosite) asbestos also are produced in the Union of South Africa. Minor quantities of anthophyllite and similar amphibole varieties are mined in the United States, Italy, Bulgaria, Finland, and several other countries.

Jun 1, 1934

Between 1985-1986, the Bureau of Mines reviewed the mining history and minerals information for areas in and near the San Isabel National Forest to appraise the mineral resources present and determine the types of deposits, and their location in the Forest, that could be mined economically if sufficient demand and metal prices existed. The two major metallic deposit-types that are of national mineral resource significance within the Forest are stockwork- molybdenum (with tungsten and tin) and carbonate-replacement zinc-lead-silver deposits. Historically, small gold placers, gold-quartz veins, silver-quartz veins, skarn iron and copper deposits, volcanogenic copper-zinc-precious metal deposits, and base- and precious-metal veins have been mined. Barite, carbonate rocks, gypsum, other non-metallic deposits, and pegmatites, have also been mined. Sand and gravel, present in large volumes, occurs along and has been mined outside the Forest along the upper Arkansas River valley. Turquoise and gemstones are present in small amounts and are of interest to collectors and jewelers. Geologically, sediment-hosted uranium and copper are present in small occurrences but no resources have been identified. Geothermal resources are related to the Rio Grande rift which parallels the central part of the Forest. Four hot spring areas are present - two of these are within the Forest. Because of the low power requirements of the region, and the presence of other generating facilities, these geothermal resources have had only limited local use. Evaluation of mine models that may be found in the region show that base-metal deposits require a high precious-metal component to be economic. Although molybdenum can be produced at economically competitive prices, there is little demand for the product. Capital costs to start new molybdenum mines would be very high and it is not likely that new mines will be put into production in the near future.

Jan 1, 1989

By J. M. Riley

A fluorometric method using morin in an alkaline-buffered chelating solution has been developed by the Bureau of Mines for determining beryllium in ores and mill products. Apparatus for measuring fluorescence intensities of the beryllium-morin reaction is described. Preparation of the sample for analysis consists essentially of digestion with sulfuric, nitric, and hydrofluoric acids, fusion of the residue with sodium carbonate and sodium borate, Solution of the melt with sulfuric acid, and proper dilution. Chemical separation of other ions is usually unnecessary. The method rave reliable beryllium determinations on samples in the 0.01- to 0.37-percent BeO range. The method is particularly applicable to low-grade beryllium ores; however, semiquantitative beryllium determinations have been made on beryl containing 12.0 percent BeO.

Jan 1, 1956

With a growing concern over mine fires, prevention and suppression are hot topics. NIOSH researchers Michael Trevits, Alex Smith and Edward Thimons discuss their research in the area. The leading causes of US mine fires include flame cutting and, welding operations, frictional heating and ignitions, electrical shorts, mobile equipment malfunctions and spontaneous combustion. From 1990 through 2007, there were 1601 reportable fires that occurred in the US mining industry -an average of 89 fires per year. The fact that mine fires are occurring with alarming regularity reinforces the importance of recognizing and eliminating the potential hazards. These statistics also show the need for improved control and suppression technology to ensure worker health and safety if a mine fire does occur.

Jan 1, 2008

By A. G. Smelley

As part of research conducted in its mission to effect pollution abatement, the Bureau of Mines, U. S. Department of the Interior, is developing a dewatering technique that allows for disposal of phosphatic clay wastes, for reuse of water now lost with clays, and for reclamation of mined land. The technique utilizes a high-molecular-weightnonionic polyethylene oxide polymer (PEO) that has the ability to flocculate and dewater phosphatic clay wastes. A synergistic flocculation study was made to determine whether a portion of PEO could be replaced by other reagents. Several groups of reagents were tested: (1) those that increased the zeta potential of the phosphatic clay wastes; (2) those capable of hydrogen bonding; and (3) those which flocculated the phosphatic clay waste. Reduction in PEO consumption occurred only with addition of those reagents able to flocculate the slime. The use of natural guar gums resulted in a lower PEO requirement and also yielded a dewatered product of higher solids content, 43 to 45 percent, versus 33 to 35 percent obtained with PEO alone.

Jan 1, 1980

By F. W. Lane

Some months ago the Bureau of Mines began research of a fundamental character on sulphur in petroleum. In the course of this work, the usual qualitative test for sulphur in organic compounds1 was applied to certain oils that were believed to contain approximately 0.5 percent sulphur. No sulphur was found, and, as a check on the qualitative test, the oils were subjected to quantitative determination of this element by the oxygen-bomb method.2 The sulphur content of the oils ranged from 0.10 per cent to 0.50 per cent. This experience led to further trial of the qualitative test for organic sulphur, both on the oils mentioned above, and on common sulphur-containing organic substances. No difficulty was experienced in detecting the element in the latter, but with the petroleum oils the test, as usually performed, could not be relied upon to detect less than 0.60 per cent of sulphur consistently. The use of mechanically polished pure sheet copper for the detection of free sulphur, hydrogen sulphide, and perhaps other sulphur compounds has been recommended.3

Jan 1, 1927

By C. J. Thompson

This Bureau of Mines study describes the preparation of sulfur compound concentrates boiling from 225° to 400° C, and reports the sulfur types detected in these concentrates by low-voltage mass spectrometry (LVMS). Existing LVMS methods were extended; the procedures described should be generally applicable to high-boiling petroleum distillates and concentrates as a preliminary means of narrowing the number of factions to be considered for more detailed separation and identification studies. The following major sulfur compound constituents of petroleum are indicated by the data: benzothiophenes, dibenzothiophenes, naphthanothiophenes, naphthenobenzothiophenes, and homologs and isomers of these. Cyclic and chain sulfides comprise a significant portion of the gas-oil range sulfur compound types. The presence of some classes of sulfur compounds containing two sulfur atoms per molecule was indicated.

Jan 1, 1966

By H. R. Hardy Jr., E. J. Kimble Jr., H. W. Shen

"The primary objective of this research project is to study the character of the bit-coal interaction during coal cutting and its influence on the size and shape distributions of the generated dust. Secondary objectives include the investigation of the acoustic emission technique as an indirect method for coal dust characterization and remote bit wear monitoring. The results of the project will be useful in developing efficient coal cutting techniques which significantly reduce the harmful coal dust components, and in providing methods for remote monitoring of bit condition and associated coal dust character. This paper will outline recent experiments carried out on coal under uniaxial compression, linear single-bit cutting, and cutting using a laboratory-scale, single-bit shearer. During the experiments acoustic emission and a variety of other mechanical parameters were monitored. · A commercially available artificial intelligence computer package, namely: JCEPAK (Intelligent Classifier Engineering Package), has been utilized to provide a powerful and objective means for AE waveform analysis. This program is able to evaluate a number of features of each AE event and to make objective comparisons between AE signals associated with different loading or cutting parameters. Finally, the paper will discuss the results obtained from a variety of coal breakage tests.INTRODUCTIONStudies to date clearly indicate that the reduction of the severity, and eventual elimination, of Coal Workers' Pneumoconiosis (CWP) depends on gaining fundamental understanding in a number of major areas. These include dust generation and entrainment, transportation, suppression, medical effects of dust and possible treatment. At present a project is underway by the authors to investigate the character of the bit-coal interaction during coal cutting and its influence on the size and shape distributions of the generated dust. An important aspect of this on-going project is the development of acoustic emission (AE) criteria which will make it possible to carry out remote monitoring of coal cutting operations. Suitable on-line analysis of monitored AE data would allow engineers to evaluate factors such as shearer bit condition and cutting efficiency, and to quantify the particle size and shape distribution of the generated dust. The on-going AE studies are fundamental in form and were undertaken to evaluate the general feasibility of AE monitoring techniques using simplified coal cutting procedures. This paper will outline recent experiments on coal under uniaxial compression, linear single-bit cutting, and cutting using a laboratory-scale, single-bit shearer. Additional information on these studies are presented elsewhere [4]."

Dec 1, 1996

By J. M. Mutmansky, S. Padmanabhan

"The subject of quartz occurrences in respirable coal mine dusts has been of increasing concern in recent years. The primary impetus for this concern has been provided by better measurement technology that has detected an increased number of mines with high quartz content in their respirable dusts. This paper presents the results of statistical analyses of quartz levels in multi-stage impactor samples from eighteen different coal mining sections located in Pennsylvania, West Virginia, Ohio, Illinois, Kentucky, Colorado and Ucah. The quartz and kaolinite determinations were then determined by combining impactor stage loadings to provide larger dust masses and applying the infrared spectrometry procedure outlined in Bureau of Mines/MSHA Method P7.The results will be presented using two categories of data collected during two separate phases of the research:(l) quartz concentration data from mines where quartz was known to be present in relatively high concentrations, and(2) quartz concentration data from mines chosen at random.The aspects of the occurrence of quartz in coal mine airborne dusts that will be reported include the size dependence of the quartz content, quartz variations with location in the mining section, and variations due to mining region. The results of the study show a strong pattern of size dependence of the quartz content in mines for which high quartz concentrations exist. A similar, though less pronounced, pattern exists in mines chosen at random. Quartz levels appear to have a varying relationship to section location and strong geographical patterns do not appear to exist in the data collected. Kaolinite content was found to be similar to that of quartz with patterns that are somewhat more consistent."

Jan 1, 1989

By James R. Boyle

The value of mineral production increased 6.2% in 1976. With the exception of coal, practically all commodities registered an increase in production and value; most had an increase in unit value. Total value exceeded $1 billion for the first time. The increase in nearly all nonmetallic mineral production was a complete reversal of the 1975 experience. Alabama led the Nation in the production of crushed marble and was second in bauxite and scrap mica, third in oystershell, third in kaolin, and fifth in dimension limes-tone and dimension marble. International Trade.-The international trade passing through the Mobile customs district was valued at $2,524 minion in fiscal year 1976, up 20% from that of the previous year. Of the total value of trade passing through the district, 52% of the value of experts and 89% of the value of imports were handled through the port at Mobile. The major export Commodity was coal through McDuffie Coal Terminal which amounted to nearly 2.9 million tons, up from 2.4 million tons in 1975. Coal exports were to Japan, Italy, Turkey, the United Kingdom, and Brazil. Other exports were cement (114,000 tons) and [ ]

Jan 1, 1979

By R. D. Leitch

The work of the United States Bureau of Mines on stream pollution by coal-mine drainage has included a study of seasonal variations in acidity and volume of several streams in Pennsylvania. The acidity of these streams has been determined during the two or three years prior to 1930 and the results may be considered to represent "normal" low water conditions. The summer of 1330, however, was unusually dry and represents what may be termed "extreme low water conditions on these streams. This report is a comparison of the results obtained for extreme low water of 1930 and for other years. The streams investigated were Buffalo Creek in Somerset County, Indian Creek (lower 5 miles) in Westmoreland County, Little Toby Creek in Elk and Jefferson Counties, Daguscohonda Run in Elk County and West Creek in Elk and Cameron Counties. These will be treated separately in the order given. Most of the descriptive matter and physical data pertinent to the streams and drainage basins are taken from published reports of the Pennsylvania State Water Supply Commission, 1917.

Jan 1, 1931

By David R. Peterson

This report presents a deep ocean mining operational simulation which is capable of describing the response of the bottom collection unit to specified mining ship maneuvers and the corresponding operation of the mining ship maneuvering system. Bathymetry, obstacles, collector and pipe dynamics and ship maneuvering capabilities are included in the simulation. The simulation is capable of evaluating the technical requirements and operating costs for specified mine plans, Results are useful in assessing mine size requirements and provide operating 'cost 'estimates useful as inputs to deep ocean mining economic feasibility assessments, The simulation is used to determine the consequences of obstacles to mining system operations in terms of impact on mine size requirements and reduced production arising from obstacle avoidance maneuvers of a towed (unsteered) collector.

Jan 1, 1979

To rapidly and dependably locate shorts and opens in mining equipment power cables. Approach: The approximate locations of faults are found using a sound pulse echo, then the faults are exactly located with one of two probes. How It Works: To approximately locate u fault in shielded or unshielded cable, the cable is disconnected from the mine power center, and connected to the sound pulse generator. The generator is also connected to the ground conductor of the cable. When the generator is energized, electrical pulses are transmitted, and each moves along the conductor until it reaches a fault. When a pulse reaches the fault an echo returns to the instrument, either a positive pulse if the fault is an open, or a negative pulse if the fault is a short. See Figure 1. The further along the cable the first fault is from the instrument, the longer it takes for the echo to return. The instrument automatically measures the time and calculates the distance. The distance in feet is shown on an illuminated digital display.

Jan 1, 1976

By E. P. Youngman

This paper is one of a series of digests of foreign mining legislation and court decisions that is being prepared in advance of a general report relative to the right of American citizens to explore for minerals and to can and ore rate mines in various foreign countries. This interpretation of the mining laws of the Irish Free State has been prepared from the best available material in Washington and is released subject to amplification and correction, if necessary, by American foreign-service officials. INTRODUCTION This paper is based upon the mines and minerals act, 1931, enacted by the Legislature (Oireachtas) of the Irish Free State (Saorstát Eireann), December 22, 1931, the lull title of which is "An act to establish a board to perform functions in relation to mines and minerals, to authorize the making of lenses of mines and minerals belonging to or vested in Saorstát Eireann, to name provider for facilitating the working of other mines and minerals and, for imposing restrictions on the working of minerals required for the support of buildings and works, to amend the law with respect to mines, and for other purposes incidental to the matters aforesaid.'

Jan 1, 1933

By John E. Miller

Absolute viscosity values for gases usually are determined with a capillary tube viscosimeter, One of the correction factors applied to the experimental data is that for nonuniformity of the capillary bore. This report contains useful analytic expressions of the nonuniformity correction for the following cases: ellipse, cone, sine wave, sawtooth wave, square wave, and the general case. The methods herein described are applied to estimate the nonuniformity of a section of stainless steel capillary tubing to be used at the Bureau of Mines Helium Research Center. Several other examples are given to illustrate the usefulness of the present results.

Jan 1, 1967