Search Documents

By Engelmann. William H.

In pursuit of innovative methods to improve mining productivity, the Bureau of Mines is investigating the use of inorganic salts as drilling fluid additives for penetration enhancement. Laboratory diamond drilling tests were performed on Westerly Granite with aluminum chloride solutions and on Sioux Quartzite with aluminum nitrate and aluminum, calcium, sodium, and zirconium chloride solutions as drilling fluid additives. These drilling results were compared with the average drilling performance using distilled, deionized water on Sioux Quartzite (12 replicate tests) and Westerly Granite (3 replicate tests). Maximum in-creases in penetration per given time and bit life were obtained when drilling with zero point of charge (ZPC) concentration solutions of each additive. For Sioux Quartzite, maximum increases in penetration and bit life ranged from 96 to 115 pct and 64 to 99 pct, respectively. For Westerly Granite, maximum increases in penetration of 155 and 165 pct and bit life of 109 and 136 pct were obtained at or near ZPC aluminum chloride concentrations of quartz (7.3 x 10-7 mol/L AIC13) and alkali feldspars (1.1 to 1.5 x 10-6 mol/L AIC13), respectively. This simultaneous increase in penetration per time together with extended bit life should result in increased productivity and reduced bit costs.

Jan 1, 1987

By A. U. Christensen

THERMODYNAMIC data for many of the common interoxidic compounds are seriously lacking, and appraisal of possible ceramic or metallurgical applications depends upon dubious estimates. In particular, high-temperature heat-content estimates may be invalid because of unknown phase-transformations. This paper reports experimental heat-content values above 298.15° K. for five interoxidic compounds-the aluminates of lithium and sodium (LiAlO2 and NaAlO2), the ferrites of lithium and sodium (LiFeO2 and NaFeO2), and lithium titanate (Li2TiO3), as obtained by the Bureau of Mines. Sodium aluminate, sodium ferrite, and lithium titanate were found to have previously unknown transformations in the crystalline state. The heats and temperatures of these transformations were evaluated as were also the heats and temperatures of fusion of sodium ferrite and lithium titanate. The heat-content results are assembled in both tabular and algebraic-equation form for use in conducting thermodynamic calculations at temperatures in the range 298°-2,000° K.

Jan 1, 1960

By E. R. Spencer, E. R. Bauer

Previous studies and research efforts have shown that noise-induced hearing loss (NIHL) is a problem in the U.S. mining industry. In response, researchers at the National Institute for Occupational Safety and Health (NIOSH) have been conducting a cross-sectional survey of equip­ment noise and worker noise exposures in the mining industry to estimate the potential for NIHL within the mining community. One commodity recently surveyed was the extraction of sand and gravel from surface pits and by dredging. To address the potential for NIHL in the sand and gravel industry, sound levels on and around the dredges and processing equipment were recorded to iden­tify areas of high noise levels. Full-shift worker dosimetry, in conjunction with task observations, was documented to determine the relationship between exposure and source. This paper presents research examining noise on dredges used in several surface mine sand and gravel operations and in the processing facilities. Results indicate that there are areas on the dredges (crane, suction pumps and diesel engines) where sound levels greater than 90 dB(A) are pres­ent. In addition, crushers and screens used in the processing of the sand and gravel also generate sound levels greater than 90 dB(A). Although no surveyed worker exceeded the Mine Safety and Health Administration’s (MSHA’s) permissible exposure level (PEL) of 90 dB(A) eight-hour time-weighted average (TWA8), laborers, mechanics, oilers, helpers, pickers and greasers are the workers most likely to be exposed to hazardous sound levels and to thus develop NIHL over time

By R. A. Cattell

With the activities of the Petroleum and Natural Gas Division geared chiefly to problems directly connected with the war effort , the emphasis of the work under oil and gas development and production was to make engineering studies of selected reservoirs for the Petroleum Administration for War , to determine the extractable quantities of components in them, and to study the characteristics of these components for use in the manufacture of aviation gasoline and other products . The needs of the Petroleum Administration for War and the operators for specific data from gas - condensate fields were fulfilled , and , in addition , engineering data along lines of a forward - looking program of research on reservoir behavior were collected , which should be of great value in the postwar period . It is planned to publish many of these data as soon as conditions permit . The work of the Secondary Recovery Section had as its objectives in- . creasing the rate of production of crude petroleum and , which is more important , preventing the premature abandonment of wells in " stripper " and marginal According to the National Survey of Stripper Wells by the National Stripper Well Association in cooperation with the Interstate Oil Compact Commission , a total of 67,460 stripper wells was abandoned from January 1 , 1935 , to July 1 , 1942 , inclusive , with an estimated loss in proved reserves of approximately 216 million barrels . This survey also indicates that over 1.2 billion barrels of oil would be recovered by primary production from more than 290,000 stripper wells then in operation , and an additional 2.5 billion barrels of oil could be recovered from them by secondary production methods . The work of the Chemistry and Refining Section was oriented towards the optimum utilization of crude oils in the manufacture of aviation fuels for spark-ignition and jet - propulsion engines . The work involved intensive studies of superfractionation , hydrocarbon analysis , and the engine testing of fuels . Particular attention was given to the effect of sulfur compounds in the crude oils and in the fuels made from them . The research on thermodynamics is concerned with the experimental determination of precise and accurate values of the fundamental thermodynamic constants of pure hydrocarbons and related compounds . The data obtained in these investigations will be utilized for devising and improving chemical processes in which petroleum hydrocarbons are the raw materials . Without such data , much time and expensive material and equipment may be wasted in attempts to obtain reactions under conditions that the laws of thermodynamics rule out of consideration . Thermodynamic data are useful and required in the petroleum industry for calculations of heat balances in the design of furnaces , fractionating towers , and heat- transfer equipment . It is of utmost importance , also , to know the heat requirements of cracking and other chemical reactions so that heat may be supplied or dissipated in the proper proportions . These needs for thermodynamic data are being recognized more and more by petroleum -refining engineers . The responsibility for the production of helium for the Navy , the Army , other governmental agencies and non-Federal users is vested in the Bureau of Mines by an Act of Congress ( 50 Stat . 885 ; 50 U.S.c. 161-166 ) . The Helium Subdivision of the Petroleum and Natural Gas Division continued to meet all demands for helium .

Jun 1, 1949

By John Ward Smith

This paper describes and evaluates a method that the Federal Bureau of Mines used to determine the ultimate composition of the organic material in 10 samples of oil shale from the Mahogany zone of the Green River formation in Colorado and Utah. Since interest has centered on the Mahogany zone, the richest section of the deposit, these 10 samples were chosen to provide a broad representation of this zone with the objective of obtaining generally valid ultimate composition values. The most probable organic composition for the Mahogany zone and the 95-percent confidence limits for each component average (in weight-percent of organic material) are: Carbon 80.5 ± .4 Hydrogen 10.3 ± .1 Nitrogen 2.4 ± .1 Sulfur 1.0 ± .1 Oxygen 5.8 ± .5 As only minor variations in composition were observed, the organic material of this particular bed is quite similar over a wide geographic area.

Jan 1, 1961

By R. L. Grant

The principal official test performed by the Bureau of Mines to determine the permissibility of coal-mine explosives, commonly referred to as the gallery test, has been in use at the Bruceton station for many years (2, 16).4/ In this test the explosive under study is loaded into the borehole of a steel cannon and fired into a flammable mixture of natural gas and air or natural gas, air, and coal dust. To meet the requirements for permissibility, the explosive must not ignite the gas mixture under the conditions of the test. There is little doubt that these tests have succeeded in the main objective, namely, to screen the relatively safe from the relatively hazardous explosives. It has been generally conceded that adoption of permissible explosives by the coal-mining industry in the United States has substantially reduced the frequency of disastrous underground explosions caused by blasting. In recent years, however, research workers planning programs for improving the safety of coal-mine explosives have felt the growing need of a more quantitative method for measuring the incendivity of explosives based on a better understanding of the role of the important variables in the gallery tests, Accordingly, it was decided to apply certain statistical methods and techniques to the gallery test to develop it into a more precise tool for evaluating permissible explosives. One of the first and more important methods applied for this purpose was the up-and-down technique (6,7,17), It was demonstrated (14,15) that the weight of the explosive charge directly affects the ignition probability of the natural gas-air atmosphere and that the curve of ignition probability versus charge weight is a cumulative normal curve. Following these experiments, a program, still in progress, was set up to study how the addition of sodium chloride to various permissible-type ex-plosives affects their incendivity. This program resulted in 3,294 shots,

Jan 1, 1961

By A. N. Fried

With the growing importance of fluid injection in recent years, the petroleum industry has been investigating and field- testing a variety of new methods designed to modify the physical properties of reservoir oil to improve the efficiency of gas and water injection. These procedures include condensing-gas drive, LPG (liquefied petroleum gas) injection, alcohol-slug process, high-pressure-gas displacement, detergent-solution flooding, and in situ combustion (30, 37).3 A new and different method to increase the effectiveness of gas and water injection has been tested by the Bureau of Mines, Consideration of both fundamental and practical factors that operate to limit the oil recovery attain- able by conventional oil-displacement mechanisms led to the concept of a displacement mechanism called the foam-drive method. This report describes the experimental study that tested this concept in the laboratory.

Jan 1, 1961

By Robert M. Becker

Particle mixtures were sampled in the laboratory, using ordinary sampling procedures, to determine whether or not the compound-multinomial probability distribution and other developments of part 2 agreed with experimental results. The objective was accomplished by the Bureau of Mines by comparing the moments and moment relationships of the appropriate probability models with their corresponding experimental values over a fairly wide range. The overall agreement between the corresponding theoretical and experimental values is both good and complete. The results demonstrate that sampling to a constant amount, such as weight, of items per sample is not the same, in general, as sampling to some constant number of items per sample. The results seem to confirm all the developments of part 2 and the application of the compound-multinomial function to bulk sampling.

Jan 1, 1965

By A. T. Sweet, G. Douglas Gardner

"INTRODUCTION In the ammonium sulfate process for the production of alumina from clay,,3/ the clay is baked with amonium sulfate at about 400ºC. to form anhydrous ammonium alum and free ammonia or ammonium carbonate. The alum is leached from the baked product with water and circulating liquors and is purified by recrystallization. Aluminum hydroxide is precipitated by treating thus alum the alum the ammonia or ammonium carbonate from the baking step. Ammonium sulfate is recovered from the filtrate for reuse, and the aluminum hydroxide precipitate is calcined to produce high-purity alumina. In this process, as in other acid processes for the production of alumina, 4/ a large part of the iron in the clay is extracted. The iron tends to build up in the leach liquors and contaminate the crystals, so that its elimination is one of the most important problems in the process. A number of large clay deposits occur in the Western States. Those that have boon explored most extensively 5/contain an average of 24 to 30 percent available A12O3 and 2 to 8 percent available Fe2O3. 6/ The available Fe2O3 content of various other clays ranges from less than I percent to more than 20 percent. The available Al2O3 or Fe2O3 is usually 90 to 98 percent of the total but may be much less. In generals the iron content bears no fixed relation to the alumina content and may vary widely within a given deposit."

Jan 1, 1948

By M. J. Kovalik, D. E. Wolfson, F. Fischler

Plastometric tests were made to determine the maximum thickness of the plastic layer for different U.S. coals . The effect of test variables on the maximum thickness of the plastic layer was studied . The values for the maximum thickness of the plastic layer were found to be related to the Gieseler maximum fluidity , plastic temperature range , free swelling index , and other plastic properties of coals . Only a general relationship was observed between the plastometric parameters obtained in these tests and the coking properties of coal .

Jan 1, 1964

By Ralph H. Whaite

The Bureau of Mines program for microfilming maps of abandoned mines in the Pennsylvania anthracite region is described. A catalog of the maps that have been microfilmed in the Eastern Middle anthracite field--the first area to be covered in the program--is presented. Additional catalogs will be published as significant mining areas are completed.

Jan 1, 1965

By W. W. Adams, T. D. Lawrence

"The National Safety Competition of 1938, the fourteenth of its kind conducted by the Bureau of Mines in which bronze trophies known as Sentinels of Safety are awarded to winning companies, has just been completed and the results are presented here.With 345 mines and quarries competing, more than in any previous year except 1931, the contest revealed low accident rates at many of the enrolled plants and, which is even more remarkable, it revealed 113 mines and quarries at which no lost-time accidents occurred during the contest year.The Sentinels of Safety trophies, provided by The Explosives Engineer magazine, were awarded to four underground mines, one open-pit mine, and one quarry. Each employee of the winning plant was awarded a Certificate of Honor by the Bureau of Mines in recognition of the employee's part in helping his company to win the trophy. In addition to the award of trophies, a Certificate of Honorable Mention was awarded to each of the mines and quarries in second, third, fourth, and fifth places in their respective contest groups and also to each mine and quarry that worked 30,000 or more man-hours without a lost-time accident. Ninety-two such certificates were awarded for 1938. Twenty-three other mines and quarries also operated without an accident but worked less than 30,000 man-hours, the minimum required by the contest rules for award of Certificates of Honorable Mention.Previous to 1938, five trophies were awarded annually in the National Safety Competition. For the 1938 contest a sixth trophy was provided by The Explosives Engineer so that open-pit mines and quarries, two classes of operations that previously had been included in one group in the competition, might have separate awards."

Aug 1, 1939

By William E. Bruce

The Bureau of Mines performed drill calibration tests on two industrial percussive drills of 2-5/8- and 3-1/2-inch piston diameters to determine operating characteristics for their use in conjunction with penetration rate data in developing drillability equations and furthering the knowledge of percussive drills. The use of a linear velocity transducer for measuring piston velocities and application of its instrumentation are described. Data presented include relationships between maximum piston velocity and feed air pressure other results confirm the theory or data of previous investigators, and some comparisons are made with the performance prediction formulas of other investigators.

Jan 1, 1969

By J. Dean Warner

Alaska contains many critical and strategic minerals that are scarce in the conterminous United States. Among these are tin, tantalum, and columbium. This Bureau of Mines report summarizes available data on the production, reserves, and occurrences of these minerals in Alaska. Alaska produces about 200,000 lb of tin per year, with historical production since 1901 estimated to have totaled 5,830,600 lb. Measured, indicated, and inferred tin reserves total over 140,000,000 Ib. Much of the tin production has been from the placer mines of the western Seward Peninsula; however, most of the reserves are in that area's lode deposits. Alaskan tin occurrences are part of a belt of tin mineralization that extends along the western coast of North and South America. The Alaskan portion of this "tin belt" comprises placer occurrences and lode occurrences of five major types: greisen, vein, skarn, pegmatite, and volcanogenic massive sulfide. Greisen and vein occurrences are the most abundant, but skarn deposits have historically been the most economically important. Columbium and tantalum have not been produced in Alaska; however, they may be recoverable as byproducts of tin, tungsten, gold, or uranium mining. Approximately 135,000 Ib of columbium oxide (Cb205) are inferred within the Tofty placer deposits in the Manley Hot Springs district.

Jan 1, 1985

By P. C. Good

Tungsten metal in fused form and of high purity was prepared by reducing tungstic oxide with redistilled calcium metal in a heavy-walled sealed reactor. Alloys of tungsten with vanadium, molybdenum) chromium, columbium, and tantalum were prepared by coreduction of mixed metal oxides in the same manner. This work was undertaken by the Bureau of Mines to investigate new approaches for preparing tungsten and its alloys in high-purity form. The standard method of producing tungsten metal has been the reduction of tungstic oxides by hydrogen. The resulting metal powder is compacted, sintered, and fabricated by powder metallurgy methods. Long experience in this field has resulted in the development of a technology that (by careful control of the variables such as metal composition, particle size, and sinterng technique) is well adapted to producing wire and the small shapes usually prepared from tungsten metal.

Jan 1, 1961

By W. D. Mcmillan

Preliminary examination of the north-central Kansas clay deposits was made by the junior author during March 1943. He was accompanied by Norman Plummer, ceramist of the State Geological Survey of Kansas. Three areas Nacre selected for further investigation. Detailed field investigation by the Bureau, consisting of hand auger drilling, trenching, anti. test pitting to obtain representative samples of the clays was carried on from April to June 1943. Field .work was under the direction of Edgar B. Butte and Richard L. Schumacher, former Bureau of Mines engineers. The samples taken were analyzed at the Bureau of Mines laboratory at Rolla, Mo. Factual data obtained from the field investigation and laboratory work are set forth in this report.

Jan 1, 1948

By E. L. Rawlins

Pipe lines through which natural gas is flowing should be buried in order to minimize fluctuations in the temperature of the gas, as these fluctuations have several harmful effects. One of these effects is to decrease the accuracy of measurements of gas volume. In order to meter properly the quantity of gas flowing past any point in a transmission system, it is necessary to how the temperature of the gas. If the temperature remains fairly constant, the gas flow can be measured with a close degree of accuracy, but if it fluctuates rapidly, close measurement is impossible.

Jan 1, 1926

By E. J. Kloos, R. H. Schutz, B. I. Ferber

To Assist users in the selection of reliable and satisfactory respiratory protective devices, the Bureau of Mines has established five schedules of minimum performance requirements for the approval of respirators . The current revisions of these schedules include 13D for self-contained breathing apparatus, 14F for gas masks , 19B and the amendments to 19B for suppliedair respirators , 21B for dust , fume, and mist respirators , and 23B for chemical cartridge respirators . Copies of these schedules may be obtained from the Bureau of Mines, Publications Distribution Section, 4800 Forbes Avenue, Pittsburgh , Pa . , 15213 . Approval tests on respirators are performed only at the request of the manufacturer of the respirator and at his expense. If the device meets the approval requirements , a certificate of approval is granted on the complete respirator. This certificate states that as long as the respirator is manufactured as originally approved, or in accordance with any changes covered by an extension of the original approval, the manufacturer may advertise and sell his respirator as being approved by the Bureau of Mines. Many industries and regulatory agencies require that respirators approved by the Bureau of Mines be used where respiratory protection is needed. The Bureau of Mines, however, has no regulatory power over the use of the respirators that it approves. It acts as an impartial testing agency to insure the availability of suitable and safe respirators. At frequent intervals, the Bureau of Mines purchases approved respirators and replacement parts on the open market. These are examined for conformity to the approved status, and are checked to insure that the manufacturer's production facilities are maintaining a satisfactory quality control .

Jan 1, 1966

By Ralph H. Whaite

The Bureau of Mines program for microfilming maps of abandoned mines in the Pennsylvania anthracite region is described. A catalog of the maps that have been microfilmed in the Eastern Middle anthracite field--the first area to be covered in the program--is presented. Additional catalogs will be published as significant mining areas are completed.

Jan 1, 1965

By R. F. Linfield

Figure 1-1 shows the basic transmitter design concepts used for the pulse system, the half-wave CW system, and the full-wave CW system. The antenna current waveform is also shown for each transmitter for typical operating frequencies and antennas. The switches shown in Figure 1-i were actually implemented using solid state devices. In all three systems the signaling format may be interrupted to conserve power and thereby extend battery life. Frequency accuracy and stability is achieved using a tuning fork oscillator in the transmitters and tuning fork filters in the receivers for all three systems. This provides the narrow reception bandwidths needed to enhance signal detectability. All three systems also use frequency assignment for identification purposes. The location schemes employed are likewise identical, each being based on detecting the null (signal minimum) of the horizontal magnetic field on the surface. Since these systems are basically similar, the primary purpose is to select the system which gives the maximum signal detectability on the surface from a manpack transmitter operating in the mine. Both the pulse and half-wave C W systems use a d. c. pulse to energize the loop antenna. However, with the pulse system, this pulse duration is short compared to the pulse repetition rate (prf), whereas with the half-wave C W system the pulse duration equals one-half the period of the switching frequency. In the pulse system, energy from the battery is stored in a capacitor so that during the switching interval the internal resistance of the power source can be considered almost negligible. Both transmitters must drive a loop antenna which is a reactive load having inductance, L, and resistance, Ra.

Jan 1, 1973