Search Documents

By H. William Zeller

The U.S. Bureau of Mines evaluated the effects of two iron-based fuel additives on diesel particulate matter (DPM) emissions. The 5.6-L, six-cylinder test engine is typical of engines used in underground mines. One additive, ferrous picrate, did not measurably affect exhaust emissions. This report is mainly about a ferrocene-based additive that reduced DPM between 4 and 45 pet., depending on engine operating conditions. The report concludes that the DPM reductions were caused by the catalytic oxidation properties of a ferric oxide coating that developed inside the engine's combustion chamber. The ferric oxide coating also decreased gas-phase hydrocarbons and O2, but it increased CO2 and NOx, The increase in NOx, of about 12 pet, is considered the only adverse effect of the ferrocene-based fuel additive. The results suggest that the effectiveness of ferrocene was partially offset by increased sulfates because of the high-sulfur fuel used. Recommendations for continuing fuel additive research are presented.

Jan 1, 2010

By H. L. Gibbs

Many factors contributed to the decision to build a radiochemical laboratory at the Salt Lake City Metallurgy Research Center to investigate the application of radioactive isotopes and chemical compounds in extractive metallurgy. These reasons included the notable success achieved in biological sciences with radioisotopes, the development of reliable instruments and methods for identifying the isotopes and measuring their activities, and the commercial availability of radioisotopes in a variety of forms and known activities. The paramount reason, however, was the realization that better methods were needed for guiding and quantifying research to resolve the complex extractive metallurgy problems under study at the Research Center. This is the first of a series of reports describing the application of radioisotopes and radioactivity techniques in extractive metallurgy. The report includes a discussion of licensing and safety requirements, a general description of the laboratory and the methods used, a definition of the nature and scope of the research program, and a synopsis of the more important problems studied. Subsequent reports will concern radioactive techniques for solving specific problems in mineral dressing, hydrometallurgy, and pyrometallurgy.

Jan 1, 1960

By Maria I. De Rosa

Table 19 and figure 7 show the number of fires and fire injuries for surface metal/nonmetal mines by state during 1990-2001. Table 19 also shows the injury risk rates, employees' working hours, and lost workdays. A total of 79 fires occurred in 16 states during 1990-2001 for these mines. Forty-five of the fires caused 44 injuries and 2 fatalities (including 9 fires and 7 injuries involving contractors). The yearly average was 6.6 fires and 3.7 injuries. Sixty-five fires with 31 injuries and 2 fatalities occurred at metal mines, and 14 fires with 13 injuries occurred at nonmetal mines. The Ewhr value was 546 x 106 hr (In = 0.016), and the LWD value was 13,134. Nevada and Arizona had the most fires (19 fires, 10 injuries, and 1 fatality; and 19 fires and 11 injuries, respectively). They were followed by Minnesota (11 fires, 4 injuries, and 1 fatality) and Alaska (6 fires and 4 injuries). Of these states, Alaska had the highest injury risk rate value (In = 0.079). Table 20, partly illustrated in figure 8, shows the number of fires, fire injuries, fire fatalities, risk rates, employees' working hours, and lost workdays by time period. The number of fires increased during the second period, then decreased during most of the remaining periods. The number of fire injuries decreased during most of the periods (a small increase is seen during the last period), accompanied by a decline in employees' working hours during most of the periods (a small increase is seen during the third and fourth periods). The In values follow patterns similar to those shown by the number of fire injuries. Tables 21-26 show the number of fires by ignition source, method of detection and suppression, equipment involved, location, and burning material by time period. Figure 9 shows the major variables related to fires for 1990-2001. Table 27 shows the number of fire injuries per number of fires causing injuries and total fires by year, ignition source, equipment involved, and location.

Jan 1, 2004

By F. E. Diebold

The wastewater-treatment system of the Anaconda Mining Co., at its Butte, MT., operation has been physically and chemically characterize modeled on a computer and investigated with respect to alternate systems for economic heavy metal recovery. The system involves lime addition to a mixture of acid underground copper sulfide mine water, acid effluent water from the iron induced precipitation of copper from acid leach solution and basic suspensions of solid effluent from a concentrator plant. Experimental chemical analysis and predictive computer calculations shows that the monosulfllte and disulfllte complexes of transition metals (Iron II being dominant) and alkaline earths are 40% of the total dissolved metal load of both acid streams. The suspended solids (30% by weight) in the basic concentrator slurries are dominated by quartz and pyrite and also contain kaolinite muscovite, biotite and undissolved lime. The mixture of these three streams result's in major reductions in concentrations of Al, Cu, Fe, Mg, Mn, Sir and Zn, and a pH >7 with calcium, sodium, potassium, and sulfate being the major dissolved ions. The treatment system has been simulated in the laboratory and accurately modeled on a computer. The computer program, an altered REDEQL-EPAK, is capable of accurately predicting the amount of lime required to reach a desired effluent water. Preliminary research has indicated the usefulness of electroprecipitation as a means of recovering the valuable metal load and providing an EPA acceptable effluent.

Jan 1, 1982

This Technical Memorandum Report is a collection of three working memoranda, prepared during the course of our work for the bureau of Mines and hound together for convenient reference. These working memoranda present preliminary performance estimates, for baseband voice and narrowband through-the-earth electromagnetic communications systems of principal interest to the Bureau, for operational/emergency mine communications. The calculations were prepared to obtain early indications of the feasibility and governing parameters of such communications systems. They are based on limited, but pertinent, coal mine electromagnetic noise data acquired to-date by Bureau of Mines contractors; and of theoretical signal-attenuation characteristics for two transmitter antenna types of present interest to the Bureau. The memoranda examine the cases of baseband voice and narrowband communications for uplink and downlink transmissions, for frequencies up to 3kHz. Downlink transmissions are via a horizontal wire antenna, up-link transmissions via a vertical-axis loop antenna, for typical mine depths of 300, b00, and 1000 feet. Representative coal-mine overburden conductivities of 10-2 mhos/meter (moderate and common) and 10-1 mhos/meter (high) were used; 10-2 for voice and narrowband, 10-1 for narrowband only. Examples of high, moderate, and low; surface and subsurface; harmonic and broadband-impulsive noise conditions were taken from NBS and Westinghouse (WGL) mine noise data, together with examples of high- and low-levels of ELF atmospheric noise taken from M.I.T. Lincoln Laboratory data.

Jan 1, 1972

By M. L. Wang, S. R. Short, E. M. Daniloff, E. L. Petsonk, D. M. Mannino, G .. R. Wagner

"Background—It has been suggested that health related job selection is a major cause of the healthy worker effect, and may result in inaccurate estimates of health risks of exposures in the working environment. Improved understanding of self selection, including the role of airway hyperresponsiveness, should improve accuracy in estimating occupational risks.Methods—We evaluated symptoms of the respiratory tract, lung function, occupa¬tional and smoking histories, and airway responsiveness from a cross sectional sur¬vey of 478 underground bituminous coal miners and non-mining controls. Workers with abnormal spirometry were excluded from methacholine testing.Results—Methacholine responsiveness (= 15% decline in forced expiratory volume in one second) was associated in both miners and controls with reduced ventilatory lung function and an increased risk of respiratory symptoms. Miners with the longest duration of work at the coal face had a low prevalence of methacholine responsiveness, compared with miners who had never worked at the coal face (12% v 39%, P < 0.01). Throughout their mining careers, miners who responded to methacholine were consistently less likely to have worked in dusty jobs than miners who did not respond to methacholine.Conclusions—These results provide evidence that workers who are employed in dusty jobs are less likely than their unexposed coworkers to show increased non-specific airway responsiveness, pre-sumably as a result of health related job selection. Surveys of workers in which responsiveness data are unavailable may underestimate the effects of dust exposure on respiratory health."

Dec 1, 1996

Bosworth, T. 0. The Mackenzie oilfield of northern Canada. Petroleum Times, vol. 5, Apr. 30, 1921, pp. 489-491. Jour. Inst. Petroleum Technologists, vol. 7, Oct., 1921, pp. 276-290; discussion, pp. 290-297. Gives location of the field, some of its geology, mode of occurrence and character of the oil. See also Oil Trade Jour., vol. 12, June, 1921, pp. 48-108. Canadian Min. Jour., vol. 42, May 27, 1921, pp. 420-422. Oil and Gas Jour., vol. 20, June 3, 1921, pp. 90-90. Petroleum World (London), vol. 18, June, 1921, pp. 233-2.64, 236-238, 240-241. Bull. Canadian Inst. min. and met., July, 1921, pp. 629-638. Mining and Metallurgy, Oct., 1921, pp. 47-48. Bureau of Foreign and Domestic Commerce. Resources of Balkan and Near Eastern countries. Commerce Repts., Oct. 24, 1921, pp. 488-489. Includes summary of the mineral resources of these countries, mentioning petroleum and allied substances in Roumania, Albania, Anatolia, Mesopotamia, Palestine, Arabia, Persia.

Jan 1, 1921

By Jon G. Bredeson

A survey of electromagnetic noise reports was performed and a summary of the results are given. Industrial concerns were surveyed for techniques to minimize the effects of electromagnetic noise and are presented. The common types of communication links used in mines today are presented. A mathematical development was presented which determines the probability of bit errors versus distance for various types of communication links designed for in mine use. The probability of undetected errors for the protocols of the communication links is given together with burst error detection.

Jan 1, 1981

By P. H. Floyd

This report presents the results of laboratory and continuous mill-beneficiation tests conducted at the Bureau of Mines Northwest Electra Development laboratory, Albany, Oreg., on nonsulfide lead ore from the Sherman mine, Leland district, near Burke, Idaho. The predominant lead-bearing mineral in the ore sample treated was pyromorphite, a minor ore mineral of lead. Known reserves of pyromorphite lead ore in the United States are limited, although an appreciable tonnage of this type of ore is found in the Sherman mine. Very little pyromorphite is being mined in this mine or in the United States. This beneficiation problem presented a unique opportunity to study the mineral-dressing properties of a less widely known lead mineral, and consequently adds valuable knowledge to the ways of beneficiating ores containing nonsulfide lead values. This mineral-dressing problem was successful with conventional concentration methods of flotation and Gravity separation.

Jan 1, 1952

By Beatrice Lukens, David Schlain, John D. Prater

"The electrolytic manganese process4/ developed by the Bureau of Mines involves the electrolysis of a solution of manganese sulfate and ammonium sulfate in a diaphragm-type cell. Metallic manganese is deposited on the cathodes, and sulfuric acid is produced at the anodes. The spent electrolyte contains, in addition to the sulfuric acid, approximately 40 percent of the manganese sulfate and most of the ammonium sulfate originally present in the feed solution. This spent solution is used to leach fresh ore that has previously been subjected to a reducing roast. The resulting leach liquor is purified and returned to the cell.Manganese of very high purity is produced by the electrolytic process. The properties of this metal are so different from those of the best grade of manganese that can be made by any other commercially feasible process that it is virtually a new material. Electrolytic manganese has been used in the preparation of new high-manganese alloys with valuable properties.3/ and further developments are to be expected. The electrolytic manganese process not only results in a product of superior qualities, but is applicable to large tonnages of domestic ores that are unsuitable for direct use in producing ferromanganese.The future industrial use of electrolytic manganese is of course, related to its cost. Decreases in the cost of production will lead to wider use of the metal; conversely, increases in the volume of production made possible by greater demand will bring further .decreases in cost."

May 1, 1946

By J. S. Miller

The Bureau of Mines developed methods for fragmenting oil shale formations with chemical explosives to prepare oil shale for in situ retorting and to evaluate the extent of fragmentation by various methods. A combination of three methods of explosive fracturing was used: (1) The displacement and detonation of a liquid chemical explosive in a natural fracture system; (2) the use of 60-pct dynamite to relieve stress conditions of the rock around the wellbore; and (3) the use of pelletized TNT in a series of wellbore shots to fragment the oil shale. An attempt was made to seal or grout around the fragmented oil shale by drilling 67 holes and displacing approximately 200 bbl of neat cement in the fracture system to aid in evaluating the fragmented zone, Seven methods were used to evaluate the fragmented zone. The primary evaluation method was the recording of seismic waves to delineate the fragmented zone with results based on arrival time, amplitude, and record quality. The data from the seismic measurements indicated the extensively fragmented zone was approximately 95 ft in diameter and 70 ft thick. Results of the remaining methods of evaluating fractures--including air-flow tests, coring of the expected fragmented zone, elevation measurements to indicate overburden crowning, and surveys with high-speed camera, impression packer, and down-hole camera--agreed with and supported the data from seismic measurements. Further field application of explosive fracturing and evaluation methods is needed to determine when a zone of oil shale is effectively fragmented for efficient in situ retorting.

Jan 1, 1973

By Je M. Oh

The U.S. Bureau of Mines is conducting research on the oxidation resistance and structural stability of Fe-(0-8)Cr-(0-16)Ni-(0-16)Mn-3.5Si-lAl alloys as potential substitutes for high-Cr stainless steels. Oxidation tests were conducted in air over the temperature range of 6000 to 9000 C for up to 1,000 h. Microstructures were analyzed at room temperature after hot rolling. The oxidation properties and the structural stability were found to be greatly affected by the Cr and Mn levels. Although substitution of Mn for Ni increased the oxidation rate, the Mn helped to stabilize the austenitic microstructure. Decreasing the Cr content or increasing the Mn content produced higher oxidation rates and earlier oxide spalling. In this study, reaction kinetics, oxide morphologies, and microstructure of the alloys were investigated using scanning electron microscopy, energy dispersive X-ray analysis, X-ray diffraction, and electron microprobe analysis.

Jan 1, 1989

By R. E. Tremoureux

This paper describing the methods and costs of quarrying limestone at Sloan, Nev., is one of a series of similar papers being prepared for and published by the Bureau of Mines on this industry in the United States. These papers are designed to disseminate information regarding the methods used. The cost tabulations represent local operating expenditures only and not total production costs. It is recognized that publication of total production costs might in many instances cause embarrassment to individual producers as well as to the industry as a whole. On the other hand, operating costs are essential to the technical discussion and study of the methods Employed. The attention of the reader is specifically called to this differentiation in order that no misunderstanding of the scope of the cost tabulations shall ensue. The quarrying operations at Sloan are interesting not only from a technical viewpoint and because of the magnitude of the deposit, but also because the quarry is located in a desert region far removed from the centers of population where lime is used. The quarry and plant are in Clark County, Nev., 20 miles west of Las Vegas, which is the nearest town to the site of the Boulder Canyon Dam. Sloan is on the main line of the Union Pacific Railroad connecting Salt Lke City and Los Angeles. The latter city is 280 miles from Sloan and it is the shipping, point for all supplies.

Jan 1, 1932

By W. H. Kerns

The Taylor Creek lead-zinc deposit is on Taylor Creek, approximately 1-1/2 miles from tidewater, at the head of Duncan Canal, on the east side of Kupreanof Island, Petersburg district, southeastern Alaska. The property was located in 1903, and a 30-foot discovery cut was put to the west tank of the creek. Very little prospecting end developing has been done since that time. The property was examined by J. C. Roehm, associate mining engineer, Territorial Department of Mines, Juneau, Alaska, in June 1946. From exposure n the creek, a mineralized zone with possible dimensions of 1,700 feet by 1,000 feet was indicated. The general strike was northwest, and the dip was low and variable to the northwest. During September through November 1948, the Bureau of Mines conducted a project on the property. Four diamond-drill holes, totaling 770.5 linear feet, were drilled from the surface and 280 lineal feet of hand trenching done. The mineral deposit was found to occur as patches that appear to be a replacement in dolomitic limestone. The patches of mineralization are small, irregularly shaped, and irregularly distributed. Maps showing the location of the drill holes and trenches, analyses of the cores from the drill holes, and anal lee of the samples from the trenches accompany this report (see, also, appendixes A, B, and C).

Jan 1, 1950

By F. M. Goodwin, John Campbell, G. W. Jones

"INTRODUCTION In cooperation with the Boston Edison Co. and the Boston Consolidated Gas Co. of Boston, Mass., a survey has been conducted continuously since 1929 by the Bureau of Mines to determine the general hazards of combustible gases and vapors in manholes of the Boston Edison Co. The New England Telephone & Telegraph Co. also has cooperated in the investigation, and tests have been made in its manholes from May 1, 1933, to October 15, 1937. Yearly reports. 6/ on the results obtained since the beginning of the survey have been published.The methods and procedure of conducting the survey in 1937 were the same as heretofore."

Jan 1, 1939

By D. G. Willard

The U.S. Department of Interior, Bureau of Mines has evaluated the potential resource and annual availability of cobalt from 27 deposits or districts in 11 market-economy countries. More than 95 pct of primary cobalt production from market-economy countries, mainly byproduct output from copper and nickel operations, was analyzed. Approximately 1,200,000 mt of cobalt is potentially recoverable at the demonstrated resource level. Very large additional resources exist, especially in laterite deposits, but are at the inferred level. The producing operations evaluated in this study are expected to produce about 19,000 mt of cobalt in 1989, significantly less than the available capacity of about 31,000 mt. More than 14,000 mt per year of cobalt is produced from copper-cobalt deposits in Zaire and Zambia, of which 11,000 mt can be produced at a copper price of $O.60jlb or less with a O-pct discounted cash-flow rate of return (DCFROR). Approximately 4,400 mt of cobalt is produced annually from nickel-cobalt deposits in six countries, of which about 1,800 mt (in Canada and Brazil) could be produced at a nickel price of $1.50jlb or less at a D-pct DCFROR. Approximately 200 mt per year of cobalt is produced from a cobalt mine in Morocco. Most of the evaluated nonproducing operations and prospects that could potentially produce cobalt as a principal product or byproduct would require a total cost (including a 15 pct-DCFROR) significantly exceeding January, 1989 market prices of the principal commodities. Principal-commodity dependence, transportation routes, cobalt toxicity, and other issues that could affect the availability of cobalt are addressed herein.

Jan 1, 1991

By Harold M. Smith

Natural gas has been used as a fuel and source of energy almost from its discovery, but its use as a chemical raw material may be said to have begun in 1918, when Brooks and Humphrey3/ showed. presence of alcohols in the diluted acid oil obtained by the sulfuric acid-treatment of cracked petroleum distillates. However, development of the utilization of natural gas for chemical syntheses was slow, partly because erroneous ideas existed regarding the nonreactivity of tine hydrocarbons composing natural gas. Data accumulated by petroleum chemists throughout the world, particularly since about 1930, have shown that these hydrocarbons will react when activated by the effects of heat, pressure, chemical reagents, and light; also that the reactions can be made to proceed of practicable speeds and to provide good yields of useful products with moderate operating conditions, especially if catalysts are employed. As those results became known, the possibility of a synthetic organic chemical industry based upon these reactions became apparent, and today this industry is large and growing rapidly in importance. In this paper the story of the manufacture of chemical products from natural gas is told simply in graphic form. The industry is developing so rapidly that soma products may have been omitted, but every effort has been made to include all that are important or likely to become so. The difficulty of keeping information of this tape up to date is shown by reference to an information circular4/ or, the sore subject published by the Bureau of Mines in 1930, in which the important products are shown on a single chart, where as five charts are employed for the cane purpose at present.

Jan 1, 1940

By Kristine M. Krajnak

Occupational exposure to hand-arm vibration through the use of powered hand tools can result in reductions in tactile sensitivity, grip strength and manual dexterity. In fact, even acute exposures to vibration cause shifts in vibrotactile thresholds in exposed fingers (2,4,5). Although reductions in tactile sensitivity after acute vibration exposures are transient, cellular changes associated with this shift in sensitivity could lead to the more permanent reductions in tactile sensitivity that are a common symptom of hand-arm vibration syndrome (HAVS). Methods Animals. Male Sprague Dawley rats (6 weeks of age) were used for all experiments. Animals were housed in AAALAC accredited facilities, and all procedures were approved by the NIOSH Animal Care and Use Committee and were in compliance with the CDC guideline for care and use of laboratory animals. Vibration exposures were performed by restraining rats in a Broome-style restrainer, and securing their tails to the vibration platform using 6 mm wide straps that were placed over the tail every 3 cm. Restraint control animals were treated in an identical manner except that the tail platform was set on isolation blocks instead of a shaker. Tail temperature and current perception thresholds (CPTs). Rats were exposed to 4 h of tail vibration (125 Hz, 49 m/s2), or restraint. Tail temperature was collected prior to and immediately following the exposure using an infra-red camera. Sensory neuron function was assessed by measuring CPTs with a Neurometer (Neurotron, Baltimore, MD). Transcutaneous nerve stimulation was applied to the C10 region of the tail. Three frequencies were used to test specific fiber types (5 Hz – C, 250 Hz - Ad, and 2000 Hz – Aß). The intensity of the stimulus was automatically increased in small increments until the rat flicked its tail. Tests at each frequency were repeated until the animals displayed 2 responses that were within 2 CPT (or 0.02 mA) of each other (2-4 tests/animal). CPT tests were performed prior to the exposure, immediately following the exposure, and 24 h after the exposure. Data Analyses. Temperatures were analyzed using a one-way ANOVA with animal as a random variable. ANCOVAS were used to analyze the CPTs at each frequency. Temperature at the time of the CPT test was used as a covariate, and animal was used as a random variable Results Tail temperatures declined between pre and post exposure (F(1,25) = 62.85, p < 0.001; mean ± sem pre 25.96°C ± 0.42, post 20.71°C ± 0.77), but were back to baseline levels by 24 h after the exposure in both groups of rats. The ANCOVAs demonstrated that exposure to a single bout of vibration did not alter sensitivity of C (5Hz) or Ad (250 Hz) fibers to stimulation.

Jan 6, 2006

By William A. Beck

Since bauxite mining began in the Irwinton District, Wilkinson County, Ga., in 1912, it has been on a small scale, as most of the deposits of high-grade ore are small. The bauxite has a high silica content, and its use has been largely limited to the chemical industry. Drilling under this project did not disclose any bauxite deposits of commercial value: However, numerous holes penetrated high-alumina clay deposits, but no attempt was made to delimit them, as the project was solely an exploration for bauxite. Bauxite was first discovered near Irwinton in 1907. The district covers virtually all of Wilkinson County and extends into the adjoining counties of Washington, Baldwin, and Twiggs. Mining was begun in 1912 by the Republic Mining & Manufacturing Co. on the Honeycutt, Parker, and Daniel properties, which are 1.5 miles from Wriley on the old Irwinton to Milledgeville Road.

Jan 1, 1949

This report summarizes the cost of U.S, mining and milling industry compliance with the Environmental Protection Agency (EPA) interim water quality guidelines for waste discharges. Applicable excerpts from Public Law 92-500 are stated and interpreted in conjunction with the guidelines being used for implementation of the law. Over 200 U.S. Army Corps of Engineers applications for discharge permits were used to develop the quality and quantity data base needed to estimate the cost to comply with EPA guidelines, Cost of three basic treatment methods were considered: Aeration, addition of lime, and sedimentation. From the process design, cost-capacity graphs were developed to consider maximum flow rate, maxi lime addition, and average flow rates. The graphical method used in this evaluation should provide a reasonable guide to the effect of waste treatment and, therefore, Public Law 92-500 and corresponding EPA guidelines on the mineral processing industry. The cost of complying with the EPA guidelines will have the effect of prompting the mining industry to minimize the production of waste water and of undertaking some additional treatment, Two case studies are presented to illustrate efforts that might be fruitful for minimizing waste water production and for treatment of combinations of acid mine drainage, mill wastes, and metallurgical process wastes when treatment is deemed necessary.

Jan 1, 1975