Search Documents

By B. W. Gandrud

In July 1948, the Bureau of Mines, United States Department of the Interior, in cooperation with the University of Alabama and mine operators, published Report of Investigations 4306, "A Combination Cleaning and Dewatering Process for Treating Fine 'Sizes of Coal, Preliminary Report In this report a new process, referred to as kerosene flotation; was described, and results of experimental work with the process Previous to the fall of 1947 were given, The contents of the report. were summarized on pages 19 and 20' as follows: In coal-preparation plants using wet methods of cleaning, the most difficult problem is the cleaning and dewatering of the "fines" from about 10-Mesh to 0. A combination proceed is now under investigation that shows promise of practically and feasibly solving this problem. The process is similar to froth flotation, but a generous quantity of kerosene is used as one of the reagents, and the feed is from approximately 10-mesh to 0 considerably coarser than the usual froth flotation feed. The kerosene and the coarseness of the reed result in a floated product that, under certain circumstances, can be dewatered satisfactorily by a simple process of mechanical squeezing, Squeezing is accomplished by means of an ordinary conveying' Auger-and trough assembly with a section of pipe easing at the outer end of the trough. The bottom of the trough and. casing is fitted with wedge-wire sections to permit escape of the water freed by the squeezing action of the auger. On account of the important role of the kerosene, the process has been referred to in this report as kerosene flotation. Up to now, the investigative work has been divided about evenly between the laboratory and commercial plants. Nearly all of the work has been done on sludges containing the solids from the underflow of dewatering screens. A few runs have been made on 10-mesh to 0: fines from raw coal, but in some of those runs the dewatering mechanism, failed to function.

Jan 1, 1950

By Thomas J. Peters

A mineral survey of the Sill Hill RARE II area (No. 5304), covering 5,200 acres (2,100 ha) of the Cleveland National Forest, San Diego County, California, was conducted by the U.S. Bureau of Mines and the U.S. Geological Survey. This survey was in conformance with the Resource Planning Act (RPA) of 1974, as amended by the National Forest Management Act of 1976, to provide mineral resource information for study area classification. Bureau of Mines personnel made an economic appraisal of mineral deposits by searching pertinent geological and mining publications as well as U.S. Bureau of Land Management, U.S. Forest Service, and U.S. Bureau of Mines files and records. Known mines, prospects, and mineralized localities were examined during 1981, and sampling and mapping were done where warranted. The Geological Survey 'did geologic mapping, geochemical sampling, and geophysical surveys to aid this study.

Jan 1, 1983

By C. J. Wilhelm

The disposal of brines produced with crude petroleum and natural gas has been a long-continuing problem to oil and gas operators as well as to farmers and stock-raisers in the vicinity of producing fields. An impartial appraisal of conditions pertaining to the problem of brine disposal leads to the conclusion that study of the technical consideration, with proper weight given to the economic and social factors, is the most desirable approach to this problem. Brine disposal is a problem of such magnitude in certain areas in the State of Kansas that in August 1934 a cooperative agreement was made between the Kansas State Board of Health and the U. S. Bureau of Mines for a cooperative technical study of methods of brine disposal.

Jan 1, 1935

By K. E. Stanfield

The oil yields of sections of Green River oil shale in Colorado, Utah, and Wyoming are presented as part of a continuing project to determine oil-shale reserves in the United States. Oil-yield logs, based upon analyses obtained from 1945 through 1952, are presented to show the thickness and richness of 202 sections of Green River oil shale. The logs are based on analyses of approximately 20,500 samples, representing 179,000 feet of shale, which were made by the Bureau of Mines, and upon analyses, representing approximately 26,000 feet of shale, which were made by other agencies. The samples consisted of cores from a Bureau of Mines coring program in U. S. Naval Oil-Shale Reserve 1, Garfield County, Colo., and cores, drill cuttings, and channel samples provided by other agencies, chiefly oil companies. Most of the samples of oil shale from Utah and Wyoming were derived from oil-well drilling operations. As a result, the oil-shale sections were widely scattered and were not extensive or reliable enough to be representative of the significant deposits of Green River oil shale in these States. The oil-shale sections for Colorado, however, were more comprehensive, and a number of the sections were used in a previous report as a basis for estimating oil-shale reserves in Colorado. The present report does not give estimates of oil-shale reserves but is limited to presentation of oil-shale analyses that may be used for future reserve estimates. Other sections of Green River oil shale are being analyzed, and the results will be published in subsequent reports.

Jan 1, 1954

This manual provides instructions for installing, operating, and maintaining a protective canopy on the Joy Mfg. Co. loader. These instructions are based upon two actual install .at ions: one made in a mine on loader, model 14BU10-11AH, and one in the factory on model 14BU10- 11AH. The parts list and engineering drawings for the protective canopy are included at the end of the manual. And a discussion of some alternative design concepts is also included. The manual can also be used for retrofitting other loaders with similar protective canopies. Skilled mechanics can determine if the instructions herein would be applicable to the other loaders and can determine any necessary modifications if they are not.

Jan 1, 1973

By C. J. Wilhelm

The disposal of brines produced with crude petroleum and natural gas has been a long-continuing problem to oil and gas operators as well as to farmers and stock-raisers in the vicinity of producing fields. .An impartial appraisal of conditions pertaining to the problem of brine disposal lead to the conclusion that study of the technical considerations, with proper weight given to the economic and social factors, is the most desirable approach to this problem . Brine disposal is a problem of such magnitude 1n certain areas in the State of Kansas that in August 1934 a cooperative agreement w s made between the Kansas State Board of Health and the U. S. Bureau of Mines for a cooperative technical study of methods of brine disposal.

Jan 1, 1935

By M. F. Dunn

During a mine fire or other emergency, it may be desirable to reverse the airflow in order to provide an escapeway or to isolate a fire. Also, in colder areas, the airflow may be reversed to prevent ice buildup. When reversing main mine fans, the mine operator usually does not know what operating characteristics of flow and pressure to expect. Laboratory and field tests of vane axial main mine fans in the 7- to 9-ft diameter size range were conducted to establish forward and reverse performance characteristics under controlled conditions and at typical mine installations. The data obtained suggest that reverse performance characteristics are dependent upon the blade angle and the hub to tip ratio. There is also evidence that reverse performance can be predicted for a family of blade angles and a given hub to tip ratio. Generally, quantity of air is 30 to 65% less in reverse than when operating in the normal forward mode.

Jan 1, 1983

Provide coal mine shafts/slopes with an optimum coal mine shaft fire and smoke protection system composed of reasonably-priced, reliable hardware. Approach Accident and injury data indicate that a relatively low percentage (5%) of underground coal mine fires occur in shafts or slopes. Nevertheless, shaft or slope fires are extremely serious because they block critical escape routes for miners. That also can happen when combustion products resulting from fires in other mine areas contaminate shahs and slopes. Seeking the optimum configuration for a shaft/slope fire and smoke protection systems, the Bureau of Mines gathered data on the performance of existing fire detection devices and signal telemetry systems In several mines, and analyzed the generic protection needs of the U.S. underground coal mining industry. The optimum system developed by the Bureau provided an adequate number of detectors, a wide area of coverage, and an extensive data acquisition, analysis, display, and storage capability. This system. recommended for fabrication and in-mine testing, consisted of a microcomputer-controlled master panel located in the test mine's slope hoist room, and four remote units. Two of the remote units were placed on the surface atop upcast ventilation shafts, a third was situated underground near the slope bottom, and a fourth was installed at the slope top in intake air.

Jan 1, 1986

By Webster S. Anderson

Bureau of Mines planer mining tests on the phosphate bed of the Douglas mine, near Drummond, Mont., indicated that a competent bed with a Mohs' scale hardness of 3 to 4 cannot be mined economically with the planer. Although planer mining was feasible where the bed was fractured enough for a 4-inch depth of cut to be consistently maintained, the depth of cut in the competent beds at the Douglas mine did not exceed 0.5 inch. Average production rates were 0.15 ton per minute and 9 tons per man-shift.

Jan 1, 1966

By Danqing Xu, A. W. Khair

"This paper presents a laboratory simulation of regrinding and resulting dust generation. An Automated Rotary Coal Cutting Simulator (ARCCS) was modified to conduct regrinding experiment. In order to estimate the effects of coal properties and operating parameters on regrinding and dust generation, an orthogonal fractional factorial experimental design was implemented in regrinding experiment. Marple personal cascade impactors, Series 290, were used to measure dust concentration during experiment. Three types of coal seams, namely, Waynesburg, Pittsburgh, and Lower Kittanning, were used to represent different coal properties. Experimental results and complete parametric analysis were presented.In a rotary cutting system, all the broken coal and part of the remaining coal from previous cutting cycles must be transported through part or entire circumference of the cutting drum. This transportation of already recovered coal through the cutting zone of rotary head makes it a rotary grinder. Some of the coal particles will be subjected to secondary fragmentation or regrinding in the process. The potential effect on dust generation by regrinding is significant because the cutting head utilizes kinetic energy to comminute recov¬ered coal material. The moving bits and bit blocks on the cutting head impact coal particles and transfer some of their kinetic energy to the particles. After obtaining kinetic energy, coal particles are free to impact one another and they also impact the coal seam or cutting head. During impact, high impact force and high internal stress concentration are created in the particles. Kinetic energy is transformed into strain energy. When stored strain energy exceeds allowable strain energy, the particles will break. A great amount of respirable dust will be generated due to impact failure. In reality, regrinding occurs at the same time as primary cutting. The particles to be ground are the result of primary cutting. Both primary cutting and regrinding produce dust. Therefore, it is impossible to separate regrinding from primary cutting. In order to study respirable dust generation by regrinding and analyze the influencing parameters, a laboratory approach was adopted. In this approach, it is possible to study the regrinding separating from primary cutting."

Mar 1, 1992

By W. E. Young

This study was made to present the mining methods and costs of a uranium mine typical of other mines in the highly productive Westwater Canyon member of the Morrison formation in New Mexico. Four mining methods have been used at the Section 23 mine: the retreat- room-and-pillar method, a sublevel-slicing method (also called top-slicing), the horizontal-cut-and-fill method, and a modification of the ring-drill method. The application of the methods at this mine and at other mines in the area should be of benefit to operators with similar problems. Ore bodies in the Section 23 mine are irregularly shaped and vary in size, in rock strength, in moisture content, and in uranium concentrations; different mining methods are required and mining costs are not constant. A 6-month period of operation at the Section 23 mine was analyzed and mining costs, not including amortization, depreciation, or Federal taxes, averaged about $6.80 per ton.

Jan 1, 1965

By W. C. McBee

A family of modified-sulfur cements has been developed by the Bureau of Mines for the preparation of construction materials with improved properties. Various types of sulfur cements were prepared by reacting sulfur with mixtures of dicyclopentadiene (DCPD) and oligomers of cyclopentadiene (CPD). Durable cements were prepared with structural characteristics ranging from rigid to flexible. These cements were used to prepare corrosion-resistant materials for use in a wide variety of industrial applications where resistance to acidic and salt conditions is needed. These materials were prepared as rigid concretes, flexible pavings, spray coatings, and grouts. Production of modified-sulfur cements in a commercial-size plant was demonstrated.

Jan 1, 1981

By Grant R. Brown

This report presents the results of a study examining the relationship between supervisor characteristics and performance in underground coal mines, The specific objectives of the research include; document tasks performed by first-line supervisors during a normal shift; explain why supervisors carry out their duties as they do: identify salient characteristics of effective first-line supervisors; and formulate criteria for selecting and developing candidate supervisors. To accomplish the study objectives, on-site observation and data collection was carried out at 13 underground mines in Illinois, Ohio, and Pennsylvania. One hundred thirty-eight first-line supervisors were observed during a full work-shift and discussions with the supervisors and the mine superintendent were held during the course of the visit. The observational data from the study provide a detailed description of what supervisors to during their shift. The report begins with an introduction discussing the problem being studied and objectives of the research. The literature related to supervisor selection is then reviewed. The following section describes the research design including data collection procedures and statistical methodology used in the study. The next sections present the analysis of mine, section, crew, and supervisor characteristics. The report concludes with a discussion of the results of the study and recommendations concerning supervisor selection and development.

Jan 1, 1987

By R. B. Schluter

Magnetite pellets were simultaneously reduced and indurated on a laboratory scale in order to determine the effects of temperature, induration time, degree of metallization, and sulfur content upon the physical and chemical properties of prereduced pellets. The reductants were commercially-pure tank gases. Among the findings were these: 1,100° C is the minimum temperature that will produce acceptably hard pellets using carbon monoxide as the reduc-ing gas. Prolonged treatment time improves the pellets' crushing strength, but the rate of improvement falls off sharply after 2 hours' induration. At 1,120° C, 75-percent metallization produces the maximum crushing strength; there was no corresponding peak at 900° or 1,050° C. Sulfur in the furnace atmosphere lowers the required induration temperature. A few tenths of 1 percent sulfur in the pellet increases the sintering rate of metallic iron in pellets by forming a liquid FeS phase that facilitates iron transfer.

Jan 1, 1968

By W. H. Tavenner

The Bureau of Mines gathered test data on the use of a continuous borer in mining an anthracite bed, which was 30 feet thick on a pitch of 15° to 45°. Gangways were driven with the continuous borer, ventilation openings between gangways were driven with a large-diameter auger, and the blocks of coal between completed gangways were mined by the long-hole method, Conveyors were used to transport the mined coal. The continuous borer operated on a coal floor that was frequently soft because of heaving. The continuous borer could not bore openings on a grade exceeding 27 percent (15° pitch). Because 150 was also the lower limit of the pitch, of the bed, the continuous borer was used only to drive gangways. The continuous borer virtually filled the workplace, leaving insufficient space to place heavy-duty timber and cushioning material between the timber and coal back to allow for normal expansion of the uncut coal. The light? weight yieldable steel arch against the coal back gave inadequate support to control convergence, which in a disturbed area sometimes occurred with explosive violence. This exposed the machine operator to a hazardous condition, since a satisfactory solution could not be found, the company discontinued the use of the continuous borer.

Jan 1, 1966

By L. C. IlsLey

The cool drills that have received the approved of the Bureau of Mines may be divided into three general classes: (1) Hand drills, small drills that are held in the hands or supported against the body while in use; (2) post drills, drills that are too heavy or powerful for hand operation and therefore require some mechanical mounting when in use; and (3) drilling machines. Besides these three classes, drilling equipment has been incorporated in the design n of a number of permissible coal-cutting machines, but such drills are considered an integral part of the cutting machine and are not given separate approval. The hand drills have been described in Report of Investigations 3363, which is cite of several papers that have been published dealing with miscellaneous types of permissible motor-driven mind equipment not covered in bulletins. The present paper describes post drills and drilling machines approved by the Bureau of Mines up to July 1, 1937.

Jan 1, 1938

By R. C. Hickman

Preliminary evidence indicated that the Chattanooga Shale might constitute a potential vast low-grade source of uranium. Investigation by core drilling indicated that while the Chattanooga Shale may constitute a resource for the future, the very low (0.006 percent) average uranium content is not economic when compared with the relatively higher grade western ores. A total of approximately 12,000 feet of test drilling was done in 72 drillholes, and large samples were mined for extractive and metallurgical testing. An experimental mine site was selected on the basis of the drilling project.

Jan 1, 1967

By Terry J. Close

Between 1986 and 1989, at the request of the U. S. Bureau of Land Management, personnel from the U. S. Bureau of Mines Western Field Operations Center studied the highly-mineralized, 25,335-acre, Crack Canyon Wilderness Study Area (UT-060-028A), to evaluate its identified mineral resources. The 16-mi-long, 2-mi to 4-mi-wide stud/ area is on the southeast side of the San Rafael Swell, about 40 mi southwest of Green River, Emery County, southeast-central Utah. The study area is underlain by Mesozoic sedimentary beds. Uranium, the principle mineral resource, occurs in two formations. The principle uranium deposits are in mudstone, sandstone, and conglomerate lenses in the 22-mi-long outcrop of the Triassic Chinle Formation which parallels and straddles the northwest boundary of the study area, Some small low-grade uranium occurrences and an extensive gypsum deposit are hosted by the Jurassic-age rocks that underlie the southeast part of the study area.

Jan 1, 1989

By L. C. IlsLey

[The cool drills that have received the approval of the Bureau of Mines may be divided into three general classes: (1) Hand drills, small drills that are held in the hands or supported against the body while in use; (2) post drills, drills that are too heavy or powerful for hand operation and therefore require some mechanical mounting when in use; and. (3) drilling machines. Besides these three classes, drilling equipment has been incorporated in the design n of a number of permissible coal-cutting machines, but such drills are considered an integral part of the cutting machine and are not given separate approval. The hand drills have been described in Report of Investigations 3303, which is cite of several papers that have been published dealing with miscellaneous types of permissible motor-driven mind equipment not covered in bulletins. The present paper describes post drills and drilling machines approved by the Bureau of Mines up to July 1, 1937.]

Jan 1, 1938

By Albert W. Deurbrouck

This report describes the preparation characteristics of the significant, presently producing coalbeds in Mercer County, W. Va. Approximately 650,000 tons of coal was produced in Mercer County, W. Va., in 1960, of which over 630,000 tons was cleaned in four preparation plants. In 1960 the Pocahontas Nos. 3, 6, and 11 coalbeds supplied 99.5 percent of the total coal mined in the county. Because the number of working mines In this county was small, only six samples were collected; four of which were of metallurgical quality as mined. The remaining two samples could be upgraded by washing at suitable specific gravities. Many of the samples taken were of metallurgical quality as mined; however, the float-and-sink analysis on these coals has been included to point out their amenability to the production of premium quality, special purpose coals. In general the coals were low-volatile bituminous in rank with low ash and sulfur contents.

Jan 1, 1963