Search Documents

By Laxman S. Sundae

A U.S. Bureau of Mines designed and fabricated in-seam tester (1ST), retrofitted with a dust shroud, was used to establish a respirable dust index (RDI) and to determine cutting forces from a variety of bit types in four coal mines and a salt mine. Results from cutting tests at four coal mines showed that radial bits required the lowest cutting force and the least specific energy. Generally, for each conical bit the RDI and cutting force increased when the included bit tip angles increased from 70° to 90°. During field tests it was not possible to measure the total quantity of respirable dust produced by each cut; therefore, attempts were made to determine the amount of dust that became airborne from each test cut. The test results show that the quantity of airborne respirable dust is very erratic and cannot be related to bit type. Two statistical methods were employed to analyze RDI, but no correlation was found between the RDI and bit type. Despite scatter in test results for RDI, significant difference was found in RDI generated in four coal seams. In general, RDI increased with the increased cutting force for each coal seam from mine 1 through mine 4.

Jan 1, 1989

By J. C. Gerdeen

This project was a supporting effort with research contract H0230016 at White Pine Copper Company. Creep properties of White Pine rock were determined. These and properties for bolted joints were used in finite element analyses of sections of the White Pine Mine which included analysis of bed separations in the roof and sloping faults. In-situ experimental measurements were made of tension, compression, and bending of resin bolts by use of strain-gaged bolts. Evaluations of bolting effectiveness and comparisons of predicted and measured roof behavior are given.

Jan 1, 1976

By Robert L. Lagace

This final report documents the work dune by Arthur D. Little, Inc. (ADL) on behalf of the U.S. Bureau of Mines, Pittsburgh Mining and Safety Research Center (PMSRC), on Contract H0122026 (which began in August of 1971). Under this contract ADL provided technical assistance to the Bureau on a task basis on virtually all aspects of the Bureau's programs related to present and planned emergency and operational communications and miner location systems for underground coal mines. The work consisted of independent investigations, analyses, experiments, breadboard and prototype hardware development, workshops and technology transfer seminars on mine communications, and on-going evaluations and guidance related to the Bureau's contracted programs on electromagnetic noise, mine communications systems, and trapped miner location. This final report documents the work in two volumes, Volume I, "Emergency and Operational Mine Communications," and Volume II, "Seismic Detection and Location of Isolated Miners." The Tables of Contents of both Volumes are included in each Volume. Phase I of the contract was devoted to performing an in-depth assessment of electromagnetic noise measurements taken by several contractors and other investigators, and then defining a new noise measurement program and instrumentation system tailored to obtain the necessary but missing noise data. These data are required for use in the design of new emergency and operational communication systems. This work, and the follow-on coordination and guidance activities of ADL on this noise measurement program in subsequent phases of the contract, are treated in Part One of Volume I.

Jan 1, 1974

By George L. Gates

The Bureau of Mines studied pressure-buildup data from a number of California gas wells to determine if the reservoir properties calculated from these data correlated with field-observed reservoir properties. Pressure-buildup curves from 24 wells showed distinct changes in slope, indicating changes in permeability of the reservoir rock. Calculated distances from the wells to indicated permeability changes were in fair agreement with distances deter-mined in the field. Pressure-buildup curves from three wells had more than one distinct change in slope, indicating multiple permeability changes. Thus field data supported the theoretical relations used to calculate reservoir properties from pressure-time relations measured in gas wells.

Jan 1, 1967

By K. K. Kershner

The purpose of this investigation was to develop methods, on a laboratory scale, for recovering tin from Bolivian metallurgical slimes. Petrographic and chemical analyses were made of slime ore fractions from several well-known tin operations. High percentages of the total tin were volatilized as chlorides at temperatures below 600° C. Under optimum conditions reaction rates were relatively rapid, and the chloridizing reaction approached completion. Owing to the low temperatures involved and the high yields of tin, the process was considered to have possibilities for treating Bolivian slimes on a commercial basis. ACKNOWLEDGMENTS Appreciation is hereby extended to the Patino Mines and Enterprises, Inc., of Bolivia, for supplying slimed tin ores that were used in the experimental work. This company has since been nationalized.

Jan 1, 1959

By Victor E. Kral

"SUMMARYFollowing a magnetometer survey on the McCoy iron deposit, a trenching and drilling program was carried out by the Bureau of Mines in August 1944.This deposit is 32.3 miles southwest of Battle Mountain in the McCoy Mining District, Lander County, Nevada, and lies on the east flank of the Fish Creek Mountains at an altitude of 5,400 feet, about 1 1/2 miles south of the gold camp of McCoy.Total production from the deposit has been 400 tons of magnetite, mined by hand and shipped to the west coast for ship's ballast.Bureau drilled two holes to a total depth of 92 feet and excavated 12 feet of trenches. Both holes were drilled in the same ore body and engineered magnetite ore 14 and 11 feet thick. Trenching was used successfully to show the lateral limits of the ore.Magnetite ore bodies were found to occur as replacements of a limestone bed in quartzite. They outcrop near and parallel to the exposure of a diorite entrusting that forms a long westward-trending ridge. Although magnetic outcrops can be traced for 5,000 feet trenching definitely proved the ore bodies to be disconnected to have little or no lateral extent beyond their outcrops. Only two ore bodies more than 10 feet thick were found; one of these is the inaccessible to and the other was drilled by the Bureau."

Jan 1, 1947

The selective placement of coal stripmine overburden is examined. Physical and chemical properties of spoil detrimental to revegetation and groundwater are detailed. The United States is divided into regions or similar problems. Five mining methods already used in the industry, that are capable of selectively handling waste are examined in detail. Technical and economic comparisons are made for the systems when applied to realistic mine settings. The same analysis is conducted for five novel methods capable of selectively handling waste. Comparisons are made between novel and existing methods. Suggestions for new and modified equipment are outlined. Recommendations for further research are provided. This volume contains all Appendices to the report.

Jan 1, 1981

By Edward E. Johnson

The U.S. economy boomed in 1965, completing its fifth consecutive year of expansion. Although the advance was somewhat irregular, previous records for production, sales, employment, and income were topped. During the first few months of 1965, as the economy recovered from the depressing effects of the automobile strikes of late 1964, increases were unusually large. The gains moderated in early spring, but were stimulated at midyear by sharply rising capital outlays, excise tax cuts, in? creased Social Security payments, and accelerated Viet-Nam defense expenditures. Gross national product (GNP) in cur-rent dollars rose $49.5 billion or 7.8 percent, to a total of S681.2 billion. In constant dollars (effects of price changes eliminated), GNP increased 5.9 percent, a rate considerably higher than the historical postwar annual average growth of 3.5 per-cent. Demand increased in most final markets and was especially strong for business fixed investment and consumption expenditures. With the exception of construction, most of the increases in GNP were real, since prices increased less than 2 percent.

Jan 1, 1966

By Irving Hartman

The results of the first experimental study by the Bureau of Mines on the explosive properties of metal powders were published in 1945. Since that time the explosibility of numerous other industrial dusts and powders has been investigated. Part of this information has been published, but most of the data has not been released to date. This paper summarizes the results of experiments on 22 samples of titanium, zirconium, thorium, uranium, and hydrides of these metals. The major part of the investigation was made under cooperative agreement with the Atomic Energy Commission.

Jan 1, 1951

By L. A. Panek, A. J. Barry, John A. McCormick

"INTRODUCTION During recent years, roof bolting has become widely accepted as a systematic method of supporting both coal- and metal-mine roofs. Today, over 2 million roof bolts are installed monthly. Most of the information on bolt installation procedure reported to date (1,2,3,4,5,6) 3/ has been obtained by trial and error by individual groups or operators. To insure good roof control, experience and field tests have indicated that roof bolts should be installed immediately after the exposure of new roof, and they should be preloaded enough to minimize sag of the roof over the opening. The question of the proper initial preload for roof bolts is under study, although it is a general practice to impose an initial load on a bolt of approximately 10,000 pounds. This created a problem of measuring bolt loads at installations in underground mines, which was partly solved by using a commercial-type torque wrench; a device that permits a direct reading of the torque applied to the nut on a roof-bolt assembly from which the corresponding load can be determined by referring to specifications furnished by the manufacturers. However, considerable apprehension was expressed regarding the accuracy of this measuring procedure because of variations in the manufacture of roof-bolting materials and the degree of care exercised in making bolt installations. In the process of loading a bolt, only a small part of the effort is expended in producing strain in the bolt - the larger part of the effort is used in overcoming frictional effects in the nut-bolt-washer assembly. These frictional effects are subject to many factors, such as condition of threads, type of lubrication, if any, the finish on the nut and bearing plate, and the alinement of the bearing plate on the bolt. The object of this investigation was to determine the accuracy with which the load developed in a slotted-type roof bolt installed in a conventional manner in shale or sandstone roof rock can be determined from the torque applied to the nut.This report is the first of a series relating to basic research in roof bolting in underground mines. A future report will cover results obtained using expansion-type bolts under similar conditions. Other reports will consider the efficiency of bolt anchorages, the long period stability of bolts, and the design of safe and efficient roof-bolting systems."

May 1, 1953

By G. D. Andria

Contract J0275007 was to consist of a thorough two-phase statistical analysis of respirable coal mine dust data from USBM Contracts H0232061, H0232060, H0230029, H0230031, H0210050, and H0242013. Consequently, BCR cataloged and assembled relevant data items from these contracts and formulated procedures suitable for the evaluation. The selected procedure was a Multilinear Regression Analysis which related dust concentrations measured in the mine to other mine parameters. Under the first phase, a thorough analysis of the date from USBM Contract No. H0230029 was completed. Primary results from this analysis are as follows: (1) The five variables that significantly affect dust concentrations in the return behind the brattice are the spray system utilized; the distance from the face to the return brattice; the return airflow; the production rate; and the water consumption rate, in that order. These five variables describe about 85 percent of the total variation in the return dust concentration. (2) Results at the miner and jack-setter locations were somewhat less conclusive due to the fact that only 17 percent of the variation in dust at the miner could be resolved and only 48 percent of the variation at the jack-setter location could be explained. The decision of the sponsor was that these initial results revealed as much information as could be expected; thus, per instructions from the USBM, the second phase (analysis of the other five contracts) was abandoned.

Jan 1, 1978

By G. P. Houston

This is the final, report submitted for the Contract No. H0220002 with the U. S. Bureau of Mines for the design and development of a Permissible Automatic Data Acquisition System (PADAS) to measure and record roof stresses in underground mines Basically the PADAS is a portable, battery powered, 24-channel data acquisition system designed for safe unattended operation of up to 30 days duration in explosive environments. The unit will accommodate twenty-four pressure transducers or eight borehole deformation gages (or any combination) at distances up to 300 feet from the PADAS to measure pressures up to 10, 000 psig. All 24 channels as a selected group are scanned sequentially at one of several selectable rates.

Jan 1, 1973

By Sean Gallagher, John R. Bartels, Dean H. Ambrose

Remote operation of continuous miners has enhanced the health and safety of underground miners in many respects; however, numerous fatal and non-fatal continuous miner struck-by accidents have occurred when using remote controls. In an effort to prevent these injuries, NIOSH researchers at Pittsburgh Research Laboratory examined the workplace relationships between continuous miner operators and various tramming modes of the equipment using motion captured data, predicted operator response times, and field- of- view data to determine causes of operator-machine struck-by events in a virtual mine environment. Factors studied included machine speed, direction of escape, operator facing orientation relative to the machine, work posture, distance from machine, and operator anthropometry. Close proximity to the machine, high machine tramming speeds, a right-facing orientation and operator positioning near the tail all resulted in high risk of being struck. It is hoped that this data will provide an improved rationale for operator positioning for remotely operated continuous miners.

By M. C. Irani, Maurice Deul, M. G. Zabetakis, T. G. Bobick

This survey was conducted to determine the magnitude of the methane emission and control problem in U.S. bituminous coal mines. The resultant data indicate that the emission rate for any given coalbed depends primarily on the coal production rate and on mine depth, as well as on the nature of the coalbed and the surrounding strata. An excellent correlation was found between (1) the methane emission rate and (2) the product of coal production rate and mine depth for the mines in the Pittsburgh, Pocahontas Nos. 3 and 4, and the Illinois Nos. 5 and 6 coalbeds. The highest total emission rates found in U.S. bituminous coal mines were as follows, in million cubic feet per day: Monongalia County, W. Va., 39; Marion County, W. Va., 30.4; McDowell County, W. Va., 13.1; Washington County, Pa., 11.9; Greene County, Pa., 11.4; Buchanan County, Va., 21.6; Jefferson County, Ala., 10.3; and Franklin County, Ill., 6.6.

Jan 1, 1972

By Adrian Brown

Pilot Hole ?X? was drilled to test the formations through which the ventilation shaft for the proposed U.S.B.M. demonstration oil shale mine will be drilled. Five permeability tests were performed at various stratigraphic levels within this hole. The test method used was that of pumping fluids out of the hole for three hours, using the air lift method, followed by a three-hour period where the recharge was observed. Transmissivity and permeability results were determined from these test data. The test procedure used is described and supporting data for the hydrologic tests are provided.

Jan 1, 1977

By N. H. Coates

The Bureau of Mines determined average film coefficients of heat transfer for helium flowing through smooth, water-cooled tubes at Reynolds numbers of 5,000 to 25,000, helium inlet temperatures of 1,600° to 2,600° F, average temperature difference across the helium film of 800° to 1,300° F, and heat flux to 215,000 Btu/(hr)(sq ft). Since helium was the only gas used, the ranges of values for physical properties of the fluid are limited--thermal conductivity from 0.15 to 0.20 Btu/(hr)(sq ft)(O F/ft), viscosity from 0.082 to 0.104 lb/(ft)(hr), and Prandtl number from 0.63 to 0.68. Four equations, three of them dimensionless, correlate these coefficients with other properties of the helium--bulk temperature, film temperature, dimensionless parameters based on temperature, and the ratio of wall temperature to bulk temperature.

Jan 1, 1966

As part of the Phase I study activity, a questionnaire was sent to a representative sampling of mining companies to obtain information on the uses, use conditions, personnel policies and other user concerns associated with front-end loaders. On-site visits to several of the mining companies were also parried out and the questionnaire was used during these visits as well. Five major areas were dealt with in the user questionnaire. These included: 1) Front-End Loader Critique - An open-ended form was employed to permit the mining companies to describe the particular things they liked and disliked about front-end loaders, in general, and/ or specific models in particular. 2) Usage - A form indicating the functions performed by front-end loaders and the numbers, makes and models of front-end loaders being used by mining companies. 3) Environment - A form where the user indicated the various types of conditions encountered in their use of front-end loaders. 4) Personnel - A form for describing factors pertaining to the qualifications of front-end loader operators. 5) Miscellaneous and Comments - A form permitting the user to comment on his feelings toward standardization of front-end loader operator stations.

Jan 1, 1973

By P. Cole Gregory, Michael R. Yenchek, John C. Edwards

The U.S. Bureau of Mines investigated the performance of portable power cables under transient conditions. This research had a twofold purpose: (1) to define the thermal characteristics of electrically overloaded trailing cables, and (2) to conceptualize electrical protection for cables that allows maximum cable efficiency without diminishing electrical safety in underground mines. Several tasks were under- taken in support of these goals during the 3-year research effort. Overload tests ranging from 2 to 12 times rated ampacity were conducted in the Bureau's Mine Electrical Laboratory. Two thermal models of energized type G-GC trailing cables were constructed, one based on thermodynamic theory and the other using empirical data from previous Bureau load tests. The empirical model was then incorporated into an interactive computer program that can assist designers and approvers of mining machines in selecting the appropriate size trailing cable. This program can be the basis for a cable protection system that ensures that cables are not the source of fires, ignitions, burns, or explosions underground.

Jan 1, 1993

By Otto Ruhl

The Oronogo-Webb City-Duenweg district is in the northeastern part of the Tri-State zinc and, lead field. Its metal-mining history dates from the early 1850's. For some years prior to 1918 it ranked as the leading producing area of the entire Tri-State field, but by 1920 most of its mines had been abandoned and allowed to fill with water. Its mine operators had-been attracted, to the newly discovered and richer deposits around Picher, Okla. In 1943, the Orenogo Mutual Mining Co. was exploiting the Oronogo Circle deposit in the northern end of the district, and the Federal Mining & Smelting Co. was preparing to mine on its holdings in the southern part near Duenweg. The area between these two operating units ranked as the largest single block of ore reserves under water in the Tri-State field. In 1942, engineers of the Bureau of Mines, in collaboration with the William Stewart Engineering Co. of Joplin, collected all available mine maps, mine reports, and logs of old drill holes in the inundated area. From a careful study an appraisal of these data, the reserves in the block were calculated at 20,647,800 tons of ore containing 606,440 tons of 60-percent zinc concentrates and 46,970 tons of 80-percent lead concentrates. The ore was estimated to contain 1.76 percent recoverable zinc and 0.18 percent recoverable lead.

Jan 1, 1949

By F. Garacia, J. Cervik

Gob holes are routinely used by the mining industry to vent methane from gobs and to prevent it from entering the mine ventilation system. In some cases, flows from gob holes are measured by centering an anemometer on the end of a discharge pipe. These measurements are erroneous and tend to be high by as much as 30 pct. The Bureau of Mines deter- mined method factors (correction factors) for anemometer measurements taken in this manner. Method factors for 4-, 6-, and 8-in (10.2-, 15.2-, and 20.3-cm) ID pipe are 0.68, 0.71, and 0.78, respectively. Comparisons between horizontal and vertical flows indicated no significant change in method factors. Consequently, the method factors for horizontal pipe flows can be applied to vertical upward flows.

Jan 1, 1987