Search Documents

By Cleo Griffith Rall, D. B. Taliaferro

The method for determining oil and water saturations described herein has been used successfully for several years in the core laboratories of the Bureau of Mines. The apparatus constructed according to the original specifications has proved very satisfactory; in fact, it has been widely adopted by core laboratories throughout the petroleum industry. The writers have found that the method gives reproducible results, the degree of accuracy depending largely on the attention to details given by the operator. The relative importance of these details of procedure and the design of the apparatus are discussed in this report. In September 1940, the Bureau of Mines published a report describing a method used in its laboratories for the determination of the water content of oil-field cores. The procedure was essentially the same as that adopted by the American Society for Testing Materials for the determination of the water content of petroleum products, although the apparatus and technique were altered slightly to increase the precision of the method and to adapt it to the characteristics of the material to be tested. The report also contained a description of the method used at that time in the Bureau’s core laboratories for measuring the oil content of a core, utilizing the sample on which the water-saturation determination had been made. The procedure involved the transfer of the weighed sample, from which the water had been distilled and measured, to a Soxhlet extractor and the removal of the remaining oil by means of a suitable solvent. Soon after the report was published, the water-determination apparatus described therein was modified so that both the oil and water contents of a core sample could be determined simultaneously. This method, which has been described by Yuster, is now widely used throughout the industry.

Dec 1, 1946

The STATE MINERAL SUMMARIES publication provides estimated data and summaries of mineral activities at the State level for 1989. Most of the estimates are based on nine months data. These summaries have been prepared in cooperation with State geological surveys or related agencies. Individual State summaries are published separately as State Mineral Industry Surveys and copies can be obtained from the appropriate State Activities field office.

Jan 1, 1990

By R. F. Zaffarano

Intergrated energy balances and energy flows were constructed and quantified for State, regional, and national levels from four separate supply and demand commodity balances for coal, dry natural gas, petroleum and natural gas liquids, and utility electricity. These commodity balances were integrated by source and sectors through conversion and aggregation of their components to energy equivalents expressed in British thermal units (Btu). A summarization of the total gross energy components of supply and demand for commercial energy derived from direct fuels, hydropower and nuclear power, based on individual States and regions, is tabulated for 1960 and 1965. Pertinent computerization details and more than 500 individual State and regional printout tables, in both original commodity units and Btu's, are shown. Using these data, energy flows between States and regions were calculated to identify surplus and deficit energy areas. Report emphasis is on the conceptual aspects of integrated energy balances, rather than on the development of missing State energy data.

Jan 1, 1969

By Albert L. Toenges

A phase in strip mining of bituminous coal is the overturning of the surface of the land. The purpose of this report is to acquaint the operators and others interested in stripping with the work that has been done in certain States to reclaim the surface of land from which the coal has been removed by this method of raining. The preparation of this manuscript follows an extensive study of the subject in the field in the course of which a large number of strip mines were visited. ACKNOWLEDGMENT The information used in the report was obtained through the courtesy and cooperation of the operators of the mines visited, State officials and educational institutions, and others interested in the subject.

Jan 1, 1939

By Fred Leonard

This report is principally concerned with the engineering and economic feasibility of area surface coal mining systems other than draglines. This analysis evaluates shovel/ trucks, shovel/crusher/conveyors, and shovel/rail excavation and haulage systems for an assortment of geologic environments and production rates in the Powder River Basin (PRB). Shovel/trucks, front-end loaders trucks, and shovel/crusher/conveyors were studied in a multi-seam, dipping geologic area of the Four Corners Region. The Texas lignite engineering and economic research involved bucket-wheel excavators (BWE), BWE/backhoes, and scraper/backhoe combinations for overburden and coal excavation. The PRB truck/shovel study utilized the most recent computer simulation available in both the design and cost analyses. Detailed engineering analysis, followed by in-depth operating costs (operating and depreciation), result in a complete evaluation of each mining system. Cost comparisons of the different mining systems under similar geologic and production constraints are presented in the report to illustrate the estimated capital investment and production costs per ton of coal and bank cubic yard of overburden.

Jan 1, 1980

By Michael Radnor

The purpose of the study was to 1) examine the social and economic impacts of surface mine blasting in relation to variations in conditions of terrain and geology, population density and type, levels of ground motion and air blast; 2) consider technical, legal and government policy issues; and 3) examine the potential, nature and extent of surface mine blasting impacts and its regulations upon both communities and surface mining companies. Phase One designed the empirical research and technical analyses of Phase Two, focused upon surface coal mining and quarrying in the Eastern U.S. Several broad conclusions are evident: 1) blasting is not the major issue for communities or surface mine companies; 2) while the number of instances of severe cracking or annoyance are relatively small, the impact can be severe for individuals immediately involved; 3) blasting/drilling cost curves tend to rise significantly at intervals below 1.0 particle velocity, in/sec, dependent upon the size of a permit area and the size of a mine; and 4) the legal, complaint, cost and density analyses do not suggest the need for a general lowering of present regulations.

Jan 1, 1981

By P. Nicholls

[This paper sets forth the burning characteristics of coke used as a domestic fuel as shown by work of the U. S. Bureau of Mines and others. Coke is a truly smokeless solid fuel and is held in high regard for this quality. Ways are being found for making commercial coke from a wider range of cools than heretofore, and tale use of coke for domestic heating is increasing. ACKNOWLEDGMENTS The experimental work reported in this paper was conducted at the Pittsburgh Experiment Station of the U. S. Bureau of Mines cinder the authority of O. P. Hood, chief mechanical engineer; M. L. Orr, assistant feels engineer, and W. M. Brewer, junior fuels engineer, assisted by Charles Schramm cooperated in making the tests.]

Jan 1, 1929

By O. Llewellyn Jack

From September 1978 to December 1983, ESD Corporation (formerly a Division of FMC Corporation) undertook the development and testing of a bidirectional auger under contract with the U.S. Department of Energy. Underground testing began in August 1981 at Peabody Coal Company's Marissa Mine near Marissa, Illinois. The auger was developed to increase mine production and coal recovery without increasing land subsidence. It bored 4-foot-diameter by 10-foot-deep holes into pillars on 7-foot centers (each hole recovering 5 tons). All operating during this test was performed by maintenance personnel with the goal of finding ways to increase the machine potential. The maximum excavation rate achieved was 1.4 tons per minute. It was concluded that the concept of drilling short holes to extract coal from underground pillars without surface subsidence was practicable with a wheel mounted auger, but that more power was desirable for this mine, and that the hydraulically driven augering system that provided experimental versatility was not sufficiently reliable for production use.

Jan 1, 1983

By James F. O?Neil

Brown iron ore deposits in Quitman County, Ga., were investigated by the Federal Bureau of Mines in cooperation with the State of Georgia, Department of Commerce, and the University of Alabama. Ninety-one holes were drilled, having an aggregate footage of 2,188 feet; seventy-one holes penetrated 248 feet of iron mineralization. Average thickness of the ore zone was 3.5 feet under an average thickness of 14.7 feet of overburden. The drilling developed inferred reserves containing nearly 30 million long tons of crude ore with an average analysis of 28 percent iron plus minor quantities of manganese. Test work done by the Bureau on the crude ore samples indicated that they would upgrade by current lug washer practice, with the use of a 1i8-inch screen, and yield 4.4 million dry long tons of concentrate with an average analysis of 52.1 percent iron plus manganese. The weight recovery obtained was 14.7 percent. Research studies made by the Bureau showed that the weight recovery would be increased by changing the screen size without any appreciable sacrifice of grade. The average weight recovery was increased to 18 percent with a 10-mesh screen and 22.8 percent with a 20-mesh screen. Screen tests studies indicated that there was no appreciable interlocking of the iron and manganese minerals and the clay and silica waste particles of the materials retained on a 200-mesh screen. Clay was prominent in micron-size slimes. Silica was deleterious in the minus 20-mesh size.

Jan 1, 1965

By Albert W. Deurbrouck

The percentage of coal cleaned mechanically has increased greatly in the past 30 years. This technological change in preparation methods, accompanied by mechanical innovations in most phases of coal mining, has enabled the industry to supply quality coals at competitive prices. The Bureau of Mines has contributed to this progress by conducting research on coal-preparation problems, by evaluating the performance of domestic-and foreign-made preparation equipment, and by recording advances as they occur in industrial coal-cleaning practices. The Bureau's work in this field is recorded in the more than 150 technical and scientific publications listed in this volume. These reports, published by the Bureau over the past half century, document the Nation's progress in a vitally important phase of fuel technology.

Jan 1, 1961

By K. L. Rubow

"IntroductionAir sampling for airborne contaminants requires a system for moving air, a collection method, and a procedure to determine the quantity of contaminant collected. Because occupational exposure limits and air quality standards frequently are expressed in terms of concentrations, a method of determining the volume of air sampled is also needed. The four principal components in a sampling train are shown in Figure 12-1. The inlet admits the air sample into the train; the collector(s) separates the gas, vapor, or particles from the air; the flowmeter measures the rate or total quantity of air sampled; and the pump (air mover) provides the suction required to draw an air sample through the train. Inlet sampling considerations are discussed in Chapter 21. Various types of collectors are described in subsequent chapters. Flowmeters are discussed in Chapter 7.This chapter will describe the air mover portion of the sampling train and air sampling systems that contain three or four components in a convenient package. The chapter consists of two parts. The first part contains a brief description of the different types of air movers and air sampling systems. The second part consists of tables and figures showing detailed information on a wide variety of commercially available air movers and sampling systems. ient size is filled with a liquid in which the suspected contaminant is insoluble. When the liquid is allowed to escape from the vessel, it is replaced by air from the atmosphere to be sampled. Such an air sample is an integrated sample rather than an instantaneous sample because the mass of fluid requires a finite time to empty. In fact, by employing a large vessel with controlled drainage, this method can be used to move air at low flow rates through a sample collector for extended intervals. Additional discussion of this method can be found in Chapter 17."

Dec 1, 1996

By K. E. Stanfield

One of the initial projects under the oil-shale research and development phase of the Synthetic Liquid Fuels Act, Public- Law 290, 78th Congress, approved April 5, 1944, was a survey of oil shales of the United States for the selection of a site for an oil-shale demonstration plant. The oil shales were assayed by the conventional Bureau of Mines retort method proposed by Karrick and described by Guthrie in a more recent publication. From previous experience and that had in making these assays, it became evident that the assay method should be modified or replaced by a more satisfactory one. There are several outstanding objections to the Bureau of Mines oil-shale assay method: (1) the oil yields are frequently smaller than those obtained by other types of assay equipment and by commercial retorts; (2) the assayed oil yield represents only a portion of the organic matter in the shale, which under more favorable conditions, may, Jae converted, more completely into oil; (3) the retorting procedure is controlled mainly by trial-and-error methods; and (4) the assay requires approximately 6 hours for completion.

Jan 1, 1949

By William H. Schiffbauer

One of the safety and health research programs of the former U.S. Bureau of Mines Pittsburgh Research Center was the evaluation of technology that will provide remote-controlled operation of mechanized equipment in underground room-and-pillar mining. The purpose of this effort was to enable workers to be located away from the hazardous and unhealthful coal extraction area (the face). As part of this program, advanced machine navigation and control technologies were developed for underground room-and-pillar and highwall coal mining that can be applied to commercially available mining equipment. These technologies use off-the-shelf components and a flexible control software architecture to minimize the effort required to adapt them to mining equipment. An accurate, reliable navigation system that can provide the mining machine's heading and location is a critical requirement for a remote-controlled mining system. After investigating several different types of navigation sensors, researchers selected the Honeywell Ring Laser Gyro Inertial Navigation System (INS) as showing the most promise. It was installed on a continuous mining machine at our Mining Equipment Test Facility. Extensive testing at an open pit (OP) site was also performed. This report describes the INS as it was employed on the mining machine in the laboratory, in the field, and OP tests, and provides the accuracy and performance results of the OP and highwalltests.

Jan 11, 1997

By S. K. Mathur

This report identifies all the possible activities, variables and factors that contribute to the surface subsidence process over room and pillar workings. These factors are responsible for mine instability and collapse that ultimately transforms into surface subsidence. Such a failure mechanism is initiated by the failure of the mine floor bed and or the failure of the pillars or the failure of the roof after second mining, which eventually brings down the roof. The individual responses of the pillar, floor and roof rocks to the mining induced stresses and the complex interaction between these components can't be attributable to any single factor. Also, no attempt has been made to quantify the significance of each of these factors and relate to the ground subsidence due to the lack of field data. The discussion here is centered primarily on the first mining though second mining is mentioned very briefly,

Jan 1, 1982

By J. R. Thoenen

For several years the Bureau of mines has been investigating the characteristics of ground vibrations produced by quarry blasts. Considerable basic information has been obtained in the course of this study, and the results have been made known to the public through various publications listed in the accompanying bibliography The studies have been confined to obtaining fundamental knowledge of the characteristics of the vibrations themselves, because it was evident at once that he problem was extremely complicated. It was felt that any attempt to predict the effect of a ground vibration on any type of artificial structure would be useless until the complexities of building vibrations are better understood. As opportunity offered, teats wore made in various types of structures and the effects of vibrations from many different sources were measured. In one set of tests (5)4/, it was demonstrated that the behavior of a building as quite different if it was shaken by vibrations originating outside tae foundation walls than if the source of the vibrations was within the building; vibrations coming from the ground outside seemed to shake the building as a single, loosely-coupled structure, whereas mechanically induced vibrations within the house seemed to set floors and walls in motion as independent units, each of which communicated its own natural motion to the adjoining member, causing a very complicated movement that was impossible to interpret.

Jan 1, 1938

By J. R. Thoenen

For several years the Bureau of mines has been investigating the characteristics of ground vibrations produced by quarry blasts. Considerable basic information has been obtained in the course of this study, and the results have been made known to the public through various publications listed in the accompanying bibliography. The studies have been confined to obtaining fundamental knowledge of the characteristics of the vibrations themselves, because it was evident at once that he problem was extremely complicated. It was felt that any attempt to predict the effect of a ground vibration on an' type of artificial structure would be useless until the complexities of building vibrations are better understood. As opportunity offered, teats wore made in various types of structures and the effects of vibrations from many different sources were measured. In one set of tests (5)4/, it was demonstrated that the behavior of a building as quite different if it was shaken by vibrations originating outside tae foundation walls than if the source of the vibrations was within the building; vibrations coming from the round outside seemed to shake the building as a single loosely-coupled structure, whereas mechanically induced vibrations within the house seemed to set floors and walls in motion as independent units, each of which communicated its own natural motion to the adjoining member, causing a very complicated movement that was impossible to interpret.

Jan 1, 1938

By Stanley P. Jacobsen

Samples of fine coal refuse were obtained from 11 coal preparation plants throughout the United States. These samples were characterized by ash analysis, particle size, and mineral composition. From the characterization, geographical locations, and the dewatering equipment being used by the plants, five sites were selected for obtaining bulk fine refuse samples. The selected coal preparation plants were using for final dewatering thickeners followed by: a vacuum disc filter, a filter press, a belt press filter, a centrifuge, and a settling pond. None were using thermal drying. The moisture content of the final cake varied from approximately 23% to 50% depending upon the feed material, flocculant addition, and the type of equipment. The filter press gave the lowest moisture content followed by a belt press and then either a centrifuge or vacuum filter. The centrifuge products were all dried to an approximate 5% moisture in a thermal dryer.

Jan 1, 1981

By Manuel Gomez, V. F. Parry, John B. Goodman

"INTRODUCTION The need for an accurate and precise analytical method for determining moisture in coals of high water content has been recognized by the coal industry as well as the fuel technologist. Interest in this particular phase of coal technology extends back to the early work of German investigators on the brown coals of Central Europe. Studies by these workers led to the establishment of a direct immiscible liquid-distillation method 4/ as the accepted moisture determining technique in European laboratories. Direct moisture determining methods, those methods that utilize various techniques to drive off the water from a given sample of coal and either collect the water in a calibrated receiver or selectively trap the water driven off in a suitable absorber, have found little favor in the United States. They have been treated merely as research tools.5/ The problem of moisture determination in low-rank coals of the United States has not been given much consideration because such coals contribute only about 2 percent of the total United States production. With renewed activity in low-temperature carbonization and with the growth of interest in coal and coal-tar hydrogenation, the American coals of lover rank containing 20 to 40 percent bed moisture will be subjected to extensive investigation. If the low-rank coals of the United States are to be accurately appraised, the need for qualitative and quantitative analytical proceeded becomes more pronounced. These coals, especially the lignites of Texas and North Dakota, are highly susceptible to oxidation, a process that proceeds to a greater or less extort when low-rank, high-moisture coals are treated by oven-drying methods. The extent of this atmospheric oxidation has been described and evaluated by numerous workers. 7/In many respects, the problem of moisture determination in low-rank coals, those found in the United States and the high-moisture coals of Central Europe, is similar. Conversely, the problem of moisture determination assumes a different aspect when the coals of the eastern and the middle-west sections of the United States are considered. Present methods, the loss in weight gravimetic-type procedures, serve adequately to test these low-moisture coals. The determination of moisture in coals containing 20 to 40 percent water should be approached from a direct method rather than from an indirect gravimetic-type procedure because of the oxidative tendencies of these coals and the demonstratrated inability of a loss-in-weight technique to remove all the water in a given sample of coal."

May 1, 1953

By H. V. Makar

Laboratory tests were performed to obtain a quantitative description of the effectiveness of sodium sulfate (Na2SO4) for removing copper from molten iron and to determine the effectiveness of Na2SO4 on actual auto scrap. The tests were conducted on induction melted heats of iron averaging 0.58 and 1.50 percent initial copper and on cupola-melted auto scrap containing 0.45 percent initial copper. The Na2SO4 was added in powder form in amounts ranging from 2.9 to 43.8 percent of the weight of iron being treated. The data showed that copper removal for the various Na2SO4 treatments followed a similar trend, regardless of the iron composition that was tested. The equation Y = 1 - e-3.23x approximately reflects the relationship between copper removal and amount of Na2SO4 added, where Y is the fraction of copper removed and x is the ratio of the weight of Na2SO4 added to the weight of metal treated. Copper removals ranged from 3.3 to 74.5 percent and reductions down to less than 0.10 percent final copper were achieved in the auto scrap. Copper removals were generally accompanied by sulfur removal, and initial sulfur contents ranging from 0.10 to 0.20 percent were reduced to as low as 0.02 percent. High temperatures and long slag reaction times tended to induce copper and sulfur reversion from the slag, but, generally, the Na2SO4 treat¬ments were effective up to approximately 2,820° F with reaction times not exceeding 7 minutes.

Jan 1, 1968

By Wilbur L. Webb

This publication reports on the design, fabrication and test of an Improved methane monitor system for compliance to 30CFR75.313. The system will Initiate automatic shutdown of mining machinery when excessive concentrations of methane are encountered. The prime consideration: In the design were small size, Improved accuracy and reliability, fast response and a transient resistant power supply capable of reliable operation from any mine power source. The power supply contains an internal battery that provides operating power to the detection system prior to mining machine start-up or after machine shutdown. This report documents the development program from conception through in-mine testing.

Jan 1, 1978