Search Documents

By Louis A. Panek

Determining the change of stress in rock based on measurements of the deformation of a drill hole is a procedure that is increasing in popularity. A closely related procedure involves the applicat10n of this principle to determine the existing stresses in a rock medium, by cutting free (core drilling) an annulus containing the drill hole. In this Bureau of Mines report, expressions are derived from which one can calculate the stress ellipsoid--the three-dimensional change of stress, or the existing three-dimensional stress field, as the case may be. Study of these equations shows that the stress components in three dimensions can be determined by measurements in only two drill holes, and yields general principles that are useful in planning an efficient program of drilling and measurement. Procedures are given for calculating the least squares estimates of the stress components and their standard errors, and for evaluating or comparing calculated values by means of standard statistical inferences.

Jan 1, 1966

By V. F. Parry

Subbituminous coal or lignite when stored in random riles or in ordinary bins in which the temperature fluctuates and air circulates quickly undergoes objectionable physical and chemical changes, which decrease the utilization value of the fuel and increase its tendency to ignite spontaneously. Slacking takes place, and the heating value decreases. Those changes are accelerated by fluctuations of temperature and by circulation of air through the storage space. When such coals are exposed to the weather they lose moisture rapidly. If evaporation from the surface of a lump proceeds at a faster rate than that at which it is replaced by moisture from the interior, the rate of shrinkage at the surface is greater than that at the interior; consequently stresses are generated at the surface which cause the coal to disintegrate. Likewise, when moisture is absorbed by the air-dried surface the outside layers expand at a faster rate than the interior, which results in further break-down. As these cycles are repeated the lump may disintegrate completely. Therefore, successful storage of low-rank coals depends on control of the factors that influence change of moisture.

Jan 1, 1941

By Fred D. Wright

This paper describes research at the Bureau of Mines experimental oil-shale mine at Rifle, Colo., to improve blasting techniques and reduce breaking costs. Many of the conclusions are applicable to any mining operation. Experiments Were conducted on many phases of blasting. The effectiveness of various grades of explosives was compared, and several different drill-hole patterns were tried in heading rounds. An experiment was conducted to determine the maximum effective burden for various diameter blast holes. High-speed motion-picture studies were made of blasts, and the time for initial movement of rock after detonation of the explosive was measured. Experiments with millisecond-delay detonators in heading rounds proved that, when used properly, these detonators result in improved fragmentation, economical use of explosive, and compact, easily loaded muck piles.

Jan 1, 1953

By James Noll

Total carbon (TC) is sometimes used to measure or characterize diesel particulate matter (DPM) in occupational settings such as underground mines. DPM samples are collected on quartz fiber filters. When using quartz fiber ?lters, adsorption of gas phase organic carbon (OC) has been reported, causing a positive bias in the particulate TC results (adsorption artifact). Most of the data on the sampling artifacts and corrections apply to environmental air sampling, where samples are collected at a much higher filter face velocity and the OC concentrations are generally much lower relative to occupational sampling. In this study, we investigated the effects of adsorption artifact on samples from occupational settings. Samples were collected with and without denuders to determine the amount of gas phase OC collected and the accuracy of certain corrections. In underground stone mines, the adsorption artifact was found to positively bias the particulate TC by greater than 20% for filter loadings below 25 µg/cm2 TC (8-h time weighted average) 262 µg/m3). The tandem ?lter correction reduced the effect of the artifact, as high as 60% of the TC value, to less than 11% for laboratory data. It also significantly reduced the effect of the artifact obtained for field samples.

Jan 1, 2008

By Gerald W. Elger

The Federal Bureau of Mines developed a modification in the conventional Kroll process for preparing high - purity hafnium metal . This modification involved the partial replacement of magnesium by sodium in the batch reduction of purified hafnium tetrachloride to sponge metal . The raw tetrachloride was purified either by thermal degassing of the volatile contaminants to the atmosphere or by fused- salt treatment . In the fused- salt treatment , the tetrachloride was contacted with molten alkali chlorides to remove the impurities . The reaction byproducts were removed from the metal by heat treatment in an evacuated furnace . The metal sponge was consolidated by melting into buttons or ingots , which were analyzed for impurities . The purity of the metal prepared by the modified process is superior to that of the metal produced by the conventional method . The hafnium metal was comparable to crystal - bar hafnium except for the oxygen content , despite the abnormally high impurity concentrations in the raw tetrachloride . Several ingots were successfully cold - rolled to sheet .

Jul 1, 1960

The first metal-mine accident-prevention course was prepared and published in 1942-45 as a series of seven miners' circulars (Nos. 51-57). The course has been broadened in scope, revised, and brought up to date and is being published as a similar series of seven miners' circulars (Nos. 51-57, revised) on accident prevention in metal and non-metallic mines. These circulars are as follows: Injury Statistics (Miners' Circular 51), dealing with general statistics on injuries from accidents at metal and nonmetallic mines, including causes, costs, and the use of investigations and reports of all injuries.

Jan 1, 1960

By Charles Anema

The Mancarried and Helicopter Receivers were developed under the contract for trapped miner location. This program was a five phase program with 15 mancarried and 5 helicopter production receivers delivered under Phase IV and equipment documentation required under Phase V.

Jan 1, 1976

By Francis E. Federspiel

In 1984 and 1985, at the request of the U.S. Forest Service, the U.S. Bureau of Mines examined the 87,720-acre South Boise Yuba study area (formerly known as RARE II Wilderness Recommended area I-4553) to evaluate mineral resources. The study area and additions are in Blaine, Camas, and Elmore Counties, 10, about 60 mi east of Boise. Granitic rocks of the Cretaceous age Idaho Batholith occupy the western two-thirds of the study area. A Tertiary age granitic complex has intruded, and broken into small blocks, Paleozoic age sedimentary rocks in the eastern third of the study area. Tertiary Challis Volcanics overlie both of these rock types. Principal mineralized structures are gold-and silver-bearing quartz veins and shear zones trending northwest to easterly in the Cretaceous granitic rocks. Copper, lead, and zinc are accessory metals in many mineralized structures.

Jan 1, 1987

By R. A. Friedel

THE UTILIZATION by the Bureau of Mines of infrared and ultraviolet-visible spectrometry in connection with coal research has led to some basic improvements in methods, including a calibration method, a quantitative assessment of infrared spectral energy sources, and the development and perfection of infrared filters and cells. The adoption of a micropipet method to flush organic samples into absorption cells permits the investigation of vapors from organic liquids and the identification of volatile organic compounds. The spectral method has been used to investigate the infrared spectra of metal chelates, the charge-transfer complexing properties of aniline and nitrobenzene, an infrared method for determining the presence of methane in coal-mine air that has been adopted for use in enforcing the regulations of the National Coal Mine Safety Act, and atmospheric pollution including smog and odor-causing oxidation and decomposition of organic materials. Correlation of spectra and structure of organic compounds, particularly aromatics, was studied.

Jan 1, 1966

By E. L. Garton

[The oil-producing district, "Southern Oklahoma," is generally considered to be that part of the: State lying; southwest of the Arbuckle Mountains. It includes six counties: Carter, Cotton, Garvin, Jefferson, Kiowa, and Stephens. At present cost of the oil is produced from formations of Pennsylvania age. The individual crude oils resemble those produced in other parts of the State, except that the sulfur content is rather high. This report is a continuation of a study of Oklahoma crude oils3/ being made, by the Bureau of Mines, Petroleum Experiment Station, Bartlesville, Okla. in cooperation with the State of Oklahoma. Analyses are given of 27 samples obtained from 21 fields in the southern part of the State, end the physical and chemical characteristics of these crude oils are discussed briefly. Analyses of crude oils from other Oklahoma areas and publications in which these analyses may be found are listed in tables 2 and 3.]

Jan 1, 1941

By A. A. Berk

Other Federal agencies have been coming to the Bureau of Mines for help with the purchase and utilization of fuel, largely coal, almost since the day the Bureau was created in 1910. The requests covered a wide range of fuel- economy problems and included boiler-water treatment after it became apparent that water-formed deposits on heating surfaces acted as insulators, decreasing heat transfer and impairing fuel efficiency. Dr. Ralph E. Hall, a Bureau of Mines physical chemist determined the 3 reactions that cause adhering scale to form in boilers (7)2 and went on to introduce scientific principles into water treatment for scale prevention (8). Widespread publicity of these achievements increased the requests for help from Federal steam-generating plants. Since no other Federal agency (even those which were more directly concerned with testing water) wanted to provide boiler-feedwater service, the Bureau decided to continue to give requested help to Federal agencies, Later, the Congress endorsed such agency cooperation as an economy measure,

Jan 1, 1963

By Forrest T. Moyer

To keep the mineral and allied industries informed of trends in the causes of accidents and to point out the need for corrective measures, the Bureau of Mines collects, analyzes, and periodically published health and safety statistics. This report includes data for 1964 on injury experience, with related employment statistics, at coal mines in the United States. These data are presented in tabular form under the following headings: General Injury Experience Tables 1 to 6: Current data on number of injuries, degree of injury, frequency and severity rates, average severity, and related employment and production data by work location.

Jan 1, 1967

By Robert H. Merrill

This report contains a summary of the various studies made to determine the structural design of the production mine area of the Oil-Shale mine, Rifle, Colo. Prior to this investigation, it had been determined from a study of the geology, the structure of the deposit, and mining costs that the deposit should be mined by open stoping. The problem remained to determine the maximum safe roof span, the optimum extraction ratio, and the size of the pillars. These factors were determined from a study of the geologic structure of the deposit, the physical properties of the oil shale, and the magnitude and distribution of the stress around proposed underground openings. The latter was determined from both theoretical calculations and model studies. Safe roof spans, pillar sizes, pillar contours, and optimum extraction ratios were calculated from elastic theory and the physical properties of the mine rock. Safe roof spans, pillar sizes; and time effects were determined by Wright and Bucky by testing mine models in a centrifuge. The models were made from rock specimens taken from the proposed mine roof and pillars. The results from both studies agreed.

Jan 1, 1954

By Tuncel M. Yegulalp

This final report contains the results of all work performed under BOM Grant J0333905. A preliminary systems analysis of coarse-particle coal slurry pipelines as a haulage method for longwall mining systems was performed. Two exhaustive literature surveys on state-of-the-art longwall mining and slurry transport technologies were prepared. Two representative longwall systems were designed, one with conventional haulage and one with slurry haulage. These two systems were then compared on the bases of cost, safety, and reliability. The conclusions were that for the case of a two-face longwall mine, a coarse slurry transport system does not have a clear-cut cost advantage over a conventional (conveyor-hoist) system. However, indications were that a cost advantage could occur under different analytical conditions such as: (1) a larger scale mine, (2) if intangible benefits were quantified, and (3) if new generation technology rather than currently available technology were applied to the study. Budget and time constraints prevented exploration of these conditions.

Jan 1, 1982

By Charles E. Semler

The possible utility of selected compositions in the systems SrO-ZrO2-MgO and SrO-ZrO2-Dolomite for commercial refractory products was confirmed in this study. Specifically the compositions of interest are located in the sub-systems SrZrO3-ZrO2-MgO and SrZrO3-ZrO2-Dolomite. Both sub-systems have regions that are not affected by hydration, but the sub-system SrZrO3-ZrO2-MgO has a larger candidate compositional region. Solid state phase relations were determined for the subject systems over the temperature range 1600°C to 1300°C, with compatibility diagrams presented for each. The systems appear to show good refractory character with no apparent low melting compositions. As the compositions of commercial interest lie mostly in the higher ZrO2 portion of each system, information is presented regarding the firing treatment required to develop stabilized cubic ZrO2. A list of suggestions for further study of these systems, to further delineate the characteristics required for possible commercial utilization, is presented.

Jan 1, 1982

By R. A. Bloomfield

This report summarizes Bureau of Mines contract research on the disposal of retorted oil shale. A data base has been developed describing the physical-chemical properties, geotechnical engineering properties, and natural cementation characteristics of spent shale. Results of field compaction tests and seepage pond tests are presented, along with results of a partially saturated finite element seepage model used to predict infiltration and seepage rates. Preliminary engineering analyses are presented for underground disposal systems, which include material transport methods, and for a surface disposal system, which includes stability analyses.

Jan 1, 1981

By Foster Fraas

This report describes the application of pulsed magnetic fields derived from alternating and intermittent magnetizing currents. Application of such pulsed magnetic fields to the matrix-type separator permits (1) the complete discharge of the magnetic fraction with wet feeds and (2) the dry separation at particle sizes down to 325 mesh. At smaller particle s indications are that frequencies above 60 hertz will be required. Applications of intermittent magnetizing current to the cross-belt separator give the cross-belt-separator an advantage over the conventional constant-field cross-belt and induced roll separators; the intermittent current enables the cross-belt separator to separate matted fibrous and magnetically coagulating feeds, a type of feed that occasionally occurs with mineral, industrial, and secondary materials.

Jan 1, 1973

By David A. Hill

This volume contains a summary of the results of past analyses on U.S. Bureau of Mines Contract No. 80122061 which are relevant to electromagnetic location in mine rescue situations. The analytical results indicated that detection of a trapped miner equipped with a special transmitter is feasible in most situations. Location of the miner by surface measurements is also generally feasible within certain errors. The feasibility of miner detection and the accuracy of miner location have been examined theoretically for a wide variety of situations. Agreement with experimental results is generally good in cases where measurements are available. Personnel involved in the investigation include J.R. Wait (Principal Investigator), D.A. Hill (Co-Principal Investigator), K.P. Spies, A.Q. Howard, and Lana Slusher (Administrative Assistant).

Jan 1, 1974

By R. O. Kneisley

This U.S. Bureau of Mines report summarizes a study of large-scale strata response to longwall mining at a western U.S. coal mine. This study utilized surface and subsurface measurements, geologic mapping, in situ stress measurements, and pressure cell readings to characterize strata behavior. Preliminary analysis of surface subsidence and time-domain reflectometry (TDR) was used to determine a suggested main roof caving sequence. Coal ejected from the face apparently resulted from brittle failures that occurred because of lack of significant yield zone development. The combination of a strong coal with pronounced directional behavior, low overburden pressures, a good caving roof, and a high-production environment that minimized time-dependent loading apparently reduced yielding of the longwall face. The panel 1 headgate-entry design appears adequate; however, the abutment pillar and adjacent panel tailgate rib are highly stressed and may contribute to problems during second panel mining. The small chain pillar yielded after passage of the face, but the pillar width may be near maximum since evidence of a stressed core exists.

Jan 1, 2010

By A. A. Berk

Other Federal agencies have been coming to the Bureau of Mines for help with the purchase and utilization of fuel, largely coal, almost since the day the Bureau was created in 1910. The requests covered a wide range of fuel-economy problems and included boiler-water treatment after it became apparent that water-formed deposits on heating surfaces acted as insulators, decreasing heat transfer and impairing fuel efficiency. Dr. Ralph E. Hall, a Bureau of Mines physical chemist determined the reactions that cause adhering scale to form in boilers (7)2 and went on to introduce scientific principles into water treatment for scale prevention (8). Widespread publicity of these achievements increased the requests for help from Federal steam-generating plants. Since no other Federal agency (even those which were more directly concerned with testing water) wanted to provide boiler-feedwater service, the Bureau decided to continue to give requested help to Federal agencies, Later, the Congress endorsed such agency cooperation as an economy measure,

Jan 1, 1963