Search Documents

By R. M. Jimeson

Pressure-drop measurements through beds of granular iron, lathe turnings, steel wool, and parallel-plate assemblies were made at linear velocity and gas-density ranges expected in the Fischer-Tropsch hot gas recycle process.4/ Equations relating pressure drop, linear velocity, gas density, and bed porosity were derived. The results indicate that the exothermic heat of reaction can be removed at a lower cost by using catalyst beds with high porosity. INTRODUCTION The Fischer-Tropsch hot-gas-recycle process requires a catalyst offering low resistance to gas flow as one condition to economic feasibility. Conventional granular or spherical catalysts used during early development of the process in Germany did not meet this requirement. Large pressure drops across these beds made the cost of recirculating the gas excessive. The Federal Bureau of Mines is investigating the process by using novel and unusual catalysts that offer little resistance to gas flow. Pressure-drop measurements across these types of catalyst beds are discussed in this report.

Jan 1, 1959

By Floyd G. Anderson

A study was made of the effectiveness of dust-control methods being employed in connection with continuous-mining operations. Airborne dust exposures of workmen and dust loadings of return air were determined for six types of continuous-mining machines. The conditions required for control of dust exposure are summarized and include ventilation of the working face by an exhaust system. Return-air dust loadings ranging up to 13 pounds per hour are reported.

Jan 1, 1963

By Robert S. Warfield

Eight samples of high-volatile bituminous coal, each large enough for a study of its coking properties by the Bureau of Mines, were obtained from a location along the Kukpowruk River, Arctic Northwestern Alaska. Bench scale and pilot plant carbonization studies with several patterns of coal blending were conducted. The data from these tests were compared to data from similar tests on a coking blend used by the Kaiser Steel Corporation at Fontana, Calif. The majority of the samples representing the 20-foot seam was found to have significant coking properties, and produced coke approaching metallurgical quality when blended with selected coking coals. Although oxidation effects were evident in the samples representing upper portions of the seam, it appears that the whole seam could be used.

Jan 1, 1966

By W. N. Hoskins

This report covers the final results of a two-phase contract study conducted between July 1974 and October 1976. A comprehensive summary of the initial phase of the study is included. Phase I of the study involved the investigation and evaluation of all potential candidate underground systems for mining the deeper deposits of oil shale and associated minerals in the Piceance Creek basin of northwestern Colorado. Phase II called for the refinement and the detailed technical and economic analysis of the most promising system or systems, thus disclosed. Of the several systems initially investigated and evaluated, four Showed considerable merit for exploiting the deeper deposits: (1) chamber and pillar mining with spent shale backfill, (2) sublevel stoping with spent shale backfill, (3) sublevel stoping with full subsidence, and (4) block caving mining using LHD's. Final refinement and analysis of these four systems indicated their technical feasibility over at least part of the range of conditions expected in the deeper deposits. Their economic feasibility also was indicated under certain operating and market conditions. A variety of engineering, production, and cost information is provided on each of these systems.

Jan 1, 1976

By Duane L. Abata

Toxic gases produced by the detonation of six explosives were measured in an underground hardrock metal mine during actual mining operations. The six explosives included two semi-gelatin dynamites, three slurry explosives and an ammonium-nitrate, fuel-oil/ammonia dynamite combination. Explosives were detonated at the face of a drift and the toxic gases produced by the detonation were trapped to the end of the drift by a bulkhead located a short distance away from the face. Toxic gas concentrations were then measured with direct readout instruments and together with the containment volume, the toxic gas volumes per mass of explosive were calculated. Toxic gas measurements were found in the following ranges (ft3/lbm): N02 0.010-0.035; N02, 0.003-0.019; CO, 0.08-0.30; S02, 0.00-0.05; and C02, 0.7-1.8. Results showed that toxic gas production (ft3/lbm) correlated with the densities (kg/m3) and energy densities (kJ/kg) of the explosives tested.

Jan 1, 1978

By Russell J. Gartrell

This report describes the engineering feasibility and economic advantages of using a steep angle conveyance (SAC) system in conjunction with medium and large draglines to transport spoil in a typical Western Coal Mine. The SAC system, including a receiving hopper, a steep angle conveyor and a sticker/spreader, is capable of processing overburden material at the rate of 7,000 tons/hr. The unique feature of this system is the steep angle conveyor which transports the overburden material from the pit bottom to the top of the spoil at angles to 45 degrees. Compared to other means of cross-pit conveyance considered during this study, the SAC system offers the advantage of easier operation, lower conveyance cost and greater mobility. The results of this study have shown that integration of the SAC system into both established and planned new mines would improve the overall mining operation, expand the operating capability of existing equipment and reduce mining end reclamation cost.

Jan 1, 1977

By R. V. Ramani

This volume is the fourth of a four-volume final report on research carried out under a contract from the U.S. Bureau of Mines on the development of a computer simulation model for surface mine reclamation planning. The other volumes are titled as follows: Volume I: Ore Reserve Estimation, Volume II: Dragline Model, and Volume III: Mine Coordinate Generator System. The Open Pit Materials Handling Simulator (OPMHS) was first developed" in 1971 and modified and updated in 1975. The present work is an update of the 1975 version and provides a direct link between the geology and reserves system and the various activities of the mining equipment in a mining system. Also, the modeling techniques in OPMHS/2 have incorporated a flexible method for describing various equipment (shovels, trucks, belts, trains, etc.), locations, their sequence of operations, place changes, and their interactions. These features allow for studying mining equipment selection, mining method analysis and reclamation planning. This report describes the Open Pit Materials Handling Simulator Version 2 (OPMHS/2). The report details the program features, operation, and application. Through an extensive set of appendices, the data input sequence, input variable definitions, sample data listing and program output are presented in detail.

Jan 1, 1985

By Bruce Pinkston

This report presents a description of the Prototype Demonstration Vehicle and Safety Guidelines developed under U.S. Bureau of Mines Contract No. JO 366003, ?Improving Man Transit Safety. This vehicle was constructed to assess the feasibility of a set of equipment related guidelines which were drafted in Phase I of the same contract. State-of-the-Art improvements are embodied in such areas as collision survivability, occupant comfort, and multiple mode (on and off rail) operation. The electric battery powered vehicle carries a twelve man section crew at speeds up to 12 mph. The description of the demonstration vehicle Is presented In Volume I. Safety Guidelines are presented in Volume II.

Jan 1, 1981

By R. E. Gray

[The purpose of the study is to investigate cases of subsidence over abandoned mined-out areas of the Pittsburgh Coal identified from published and unpublished sources and to determine through a consideration of the geology, topography, climate, mining activity, and evidence at ground surface, what mechanisms control subsidence .and under what circumstances it takes place. The study wan performed it two phases, the first to identify all documented incidents of subsidence in mined-out areas of the Pittsburgh coal Region; and the second, to study a particular portion of the region in detail, collecting pertinent data relative to the sites within, characterizing roil the nature of the subsidence and its economic consequences, and determining the applicability of the findings to other areas whore similar problems with the collapse of abandoned miner have been encountered.]

Jan 1, 1977

By Phillip R. Moyle

Several deposits in the Sheep Hole/Cadiz Wilderness Study Area (WSA) have small identified or potential for undiscovered gold and silver resources. One prospect area is a potential target for molybdenum. Most base and precious metals and one uranium deposit in the study area are of the fissure-filling, contact metamorphic type associated with late stage fluids of the Cretaceous Cadiz Valley batholith. Some evidence suggests limited Tertiary and Quaternary mineralization. Mineral deposits are controlled by faults, shear zones, and joints which strike northwest and dip northeast or southwest. Although undefined, calcium, sodium, lithium, and strontium brines are inferred within the study area. Some potential for oil and gas and geothermal resources is indicated by the interest private industry has shown in the eastern part of the study area. INTRODUCTION The U.S. Bureau of lines and U.S. Geological Survey conducted a mineral survey of the Sheep Hole/Cadiz Wilderness Study Area (p1. 1) which encompasses approximately 205,000 acres (83,000 ha) in south-central San Bernardino County, California. The U.S. Bureau of Mines studied the mineral resources of mines, prospects and mineralized areas; geological, geochemical, and geophysical investigations were conducted by the U.S. Geological Survey.

Jan 1, 1982

By J. P. Capp

This experiment, one of a series on underground gasification of coal, was an investigation by the Federal Bureau of Mines of hydraulic fracturing as a means of increasing the air acceptance of a coalbed to permit introducing combustion air and removing product gases. Specific objectives of the investigation included: (1) Fracturing a coalbed; (2) determining the distance the coal was physically affected; (3) ascertaining the effect of the fracture on air acceptance of the coalbed; and (4) gasifying the coal. The coal was fractured with a fluid consisting of 15,000 lb. of sand mixed with 10,000 gal. of fuel oil and 5,000 gal. of kerosine, injected at pressures up to 900 p.s.i.g. and rates up to 425 g.p.m. The oil served as the fracturing medium, and the sand as a propping agent to hold the fracture open. From the fracture point, (the place in the bed where the fluid was injected), the fracture extended 200 ft. or more along the face cleats, somewhat less along the butt. cleats, and was confined to the coalbed. At the fracture point, the bed accepted about 500 std. c.f.m. of air, which was an etghtyfold increase. Fracture effects were extensive, as airflow was noted from old mine workings and outcrops 600 to 800 ft. from the fracture point. It is probable the actual fracture was much less than 600 ft. and that normal coalbed permeability beyond the fracture limits was responsible for this flow. This indicated that effects of the fracture extended beyond the area of coal physically affected. Although no attempt was made to gasify coal more than 200 ft. away, these effects plus the natural permeability of the bed likely would permit combustion beyond the outer limit of the fracture. As these experiments continued for more than 2 years, and greater air acceptance due to the fracture was observed at the beginning of each test, it is apparent that the effects of the fracturing persist for a considerable time.

Jan 1, 1960

By A. Galaitsis

This report summarizes part of the work performed under the USBM Contract No H0155113, "Noise Abatement of Continuous Mining Machines." It describes the noise source diagnosis of a Jeffrey 120M conveyor and the evaluation of several treatments all conducted in a test facility aboveground. The conveyor noise at the operator's position was gradually reduced from 101.5 to 93 dBA using damping, vibration isolation, sound barriers and smoother discontinuities. The underground performance of the selected treatments will be addressed in Volume II of the report.

Jan 1, 1979

By Lawrence J. Froisland

To aid in minimizing adverse environmental impacts of mining and mineral processing, the Bureau of Mines studied changes in soil characteristics in topsoil stockpiled during mining operations. Topsoil stockpiles in arid areas of New Mexico, Utah, and Wyoming were sampled over a 1- to 8-yr period to determine any changes in physical, chemical, or biological parameters in the top 15 ft of soil. Parameters examined in this study included soil moisture, pH, electrical conductivity, and cation exchange capacity; total nitrogen, organic carbon, carbon to nitrogen ratio, extractable potassium, and soluble phosphorus levels in the soil; general levels of bacteria activity in the soil; and productivity of the soil as measured by shoot yield in growth tests. Data were analyzed by multiple linear regression to determine possible effects of stockpile age and depth. Bacteria population counts, used as an indicator of goner l bacterial activity, was the only parameter found to be significantly correlated with stockpile age and depth at more than one site. Bacterial activity increased with depth at the two sites where it was measured. Activity increased with age at one site and decreased with age at the second. Significant changes in soil pH, electrical conductivity, and moisture were significantly correlated with stockpile age and depth at single sites. This study did not show significant, consistent deterioration in soil characteristics or growth yield of topsoil stored in stockpiles.

Jan 1, 1987

By C. E. Dobbin

The coal fields of Montana are widely distributed through the plains region in the eastern and northern parts of the State, and the mountain regions in the central, southern, and southwestern parts of the State. (See fig. 1.) SURFACE FEATURES The Fort Union region in eastern Montana is a broad plain of almost horizontal rocks, characterized by extensive "bad lands" along the larger streams and by red hills, benches, ridges, and buttes which represent shale and sandstone that have been fused by the burning of an underlying coal bed.

Jan 1, 1932

By William J. Campbell

This report describes a Bureau of Mines study undertaken to determine the applications and limitations of solution techniques as a general method of fluorescent X-ray spectrographic analysis. Systematic errors due to variations in particle size, surface preparation, and sample inhomogeneity are eliminated by the use of solutions. The range of applicability of fluorescent X-ray spectrography is increased in two ways: (1) Samples in the form of wire, filings, turnings, etc., can be analyzed as solutions, and (2) samples submitted as solutions can be analyzed as received 0 The lower limit of detectability varies from 0.14 gram per liter for sulfur, atomic number 16, to 0.0015 gram per liter for strontium, atomic number 38. Most elements have limits of detectability between 0.02 and 0.002 gram per liter.

Jan 1, 1959

By D. W. Blaylock

1. The Lower Freeport and Lower Kittanning beds are the most important beds in Clearfield County, Pa., from the standpoint of production. The Lower Kittanning bed has the largest remaining recoverable reserves of any of the beds in the county. 2. Known measured and indicated reserves in all beds, based on a minimum thickness of 14 inches and 1,800 short tons per acre-foot of coal in place, are estimated at 1,909 million short tons as of January 1, 1953. Of this total, 1,177 million short tons is in beds 28 inches and more thick. Areas in some beds were omitted from the estimate because available data relative to the bed characteristics are too meager to make an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1955

By Joseph T. Singewald

The possible value of the red hematite iron ore of the southern Appalachian States, if some practicable method of concentrating it could be devised, has long been recognized. The ore is very low grade, and although in enormous quantities, particularly in the States of Alabama, Tennessee, and Georgia, is only at a few points rich enough to work, and even the best of it ranks among the lowest grade iron ores being mined in the United States. A cheap method of beneficiating this ore would make enormous quantities available and vastly increase the iron-ore resources of the country. However, this low-grade ore in effect constitutes a potential iron reserve, and as long as ample quantities of ore can be obtained elsewhere the question of its utilization does not demand immediate notice. Where these ores are in part of workable grade, however, a problem of more immediate importance arises which, from considerations of economy and prevention of waste in their mining, ought to be solved or, at least, attacked as quickly as possible. Where these ores are being worked they are usually intimately associated with lower-grade material that in mining is left behind. The difficulty and expense of going into ground broken by old workings makes the recovery of this lower-grade ore practically impossible and it is lost forever. Success in concentrating the red ores, therefore, would save material that is now being irretrievably lost. The successful large-scale concentration of law-grade ore in the last few years on the Lake Superior iron ranges should encourage the attack of similar problems in the Birmingham district.

Jan 1, 1917

By A. Brown

This report details work performed and results obtained in a study of the water management aspects of oil shale mining and retorting in the Piceance Creek Basin. Three specific sites were investigated, and optimal water management systems for both conventional and in-situ extraction processes were generated. Water-related legal and environmental constraints on development were identified and the water management schemes were developed in compliance with these regulations. Limitations on shale oil production implied by limited water supplies were evaluated. Potential Basin-wide effects of development were evaluated using a computer model, and mitigation strategies were developed. Recommendations for additional investigation and analyses were presented.

Jan 1, 1977

By E. G. Davis

The Bureau of Mines investigated gaseous direct reduction of low-grade iron ore concentrates in a continuous fluid-bed reactor. These studies were made in a 4-inch diameter fluid-bed reactor using hydrogen alone, and oxygen-or air-reformed natural gas as the reductants. The percent reduction is directly dependent on the mole ratio of hydrogen in the reducing gas to the oxygen associated with the iron oxide in the ore. Two-and three-stage fluid bed tests were simulated by repeated continuous tests. The results showed that percent reduction of the final product was dependent on the mole ratio of the quantity of hydrogen in the gas of each stage to oxygen in the iron oxide of the initial ore feed. Reduction as high as 87 percent in the single stages and as high as 94 percent in the multistages was obtained when either hydrogen or reformed natural gas was used as the reducing gas. Magnetic separation and concentration of the highly reduced fluid-bed product yielded a high metallic iron concentrate analyzing 85 percent total iron and 80 percent metallic iron with total iron recovery as great as 90 percent. Agglomeration of the high-grade metallized concentrate produced hard pellets analyzing 85 percent total iron and 78 percent metallic iron. Green pellets, with good strength, were made without any binder in a drum pelletizer. Direct melting of the high-metallic fluid-bed product in a basic lined arc furnace produced a nearly pure iron which contained 0.09 C and 0.01 P with 95 percent recovery of the metallic iron in the metal.

Jan 1, 1972

By Pedro Lilienfeld

This report describes a program to develop, design, fabricate and subject to environmental testing three prototype collection-sensing devices of an eventual mining-machine mounted automated monitor for the measurement of the respirable fraction of coal mine dust to determine both short-term as well as average mass concentrations over typical 8-hour shifts. The design of this instrument is based on collection by filtration and mass sensing by beta-radiation attenuation. The emphasis of this development program was to evolve a rugged, stable and reliable collection-detection head compatible with the environment to which An eventual monitor will be subjected. Laboratory testing of this prototype instrument was performed over a representative range of temperature, humidity, dust concentration and composition, shock and vibration. The results of this testing program indicated that the operation of the prototype version His compatible with these environmental conditions and that further development of this configuration into a field operational device is justified.

Jan 1, 1977