Search Documents

By P. R. Tisot

Structural response and/or deformation was determined for each of four different grade Green River oil shales (27.0-, 34.5-, 45.5-, and 63.5-gal/ton) as they were heated in an inert atmosphere, under constant compressive stress, from ambient to subretorting temperatures; that is, below those required for rapid pyrolysis of the organic matter. Small cores and small columns of confined fragments comprised the test specimens, which were heated, in a specially designed microunit, at a uniform rate either to 725° or to 825° F under three different stress levels, 80, 200, and 325 psi. Structural response of some cores was observed as they were heated in a stress-free environment. The obtained stress-strain-time-temperature relationships provide information regarding the oil shale's yield temperature, yield stress, rate of compressive strain, loss of mechanical strength, and nature of structural deformation. Effects of structural deformation on induced permeability in small columns of fragments are presented. Results indicate that underground retorting of Green River oil shale may be seriously impaired through loss of induced permeability brought about by structural deformation of rich oil shale under the influence of heat and compressive stress.

Jan 1, 1971

By Albert L. Toenges

This paper is the fourth of a series5/ that describes some methods and practices of mining coal mechanically where operations are conducted on more than one shift. Many inquiries have been received regarding methods of extracting pillars with mechanized equipment, and this paper deals primarily with this phase of mechanical mining. Some of the questions that have been asked are:

Jan 1, 1942

By W. W. Scott

Measurements of the absolute value of electromagnetic noise and attenuation along a hoist rope were made in an operating hard-rock mine, Lucky Friday Mine, located near Wallace, Idaho. Spectra of electromagnetic noise generated by various pieces of equipment, spectra of specific noise signals at various depths, and noise and attenuation on the 4250 foot (1295 meter) hoist, were measured. Three techniques were used to make the measurements. First, noise was measured over the entire electromagnetic spectrum of interest for brief time periods. Data were recorded using broadband analog magnetic tape for later transformation to spectral plots. Second, noise amplitudes were recorded at several discrete frequencies for a sufficient amount of time to provide data for amplitude probability distributions. A third technique gave attenuation data through the direct measurement of field strength at various depths. The specific measured results are given in a number of spectral plots, amplitude probability distribution plots and amplitude curves as a function of depth.

Jan 1, 1974

By J. M. Riley

This report summarizes Bureau of Mines experiments in purifying sulfate leach liquors, which were prepared from low-tenor beryl concentrates by modifying the Degussa process. The leach liquor was prepared from a beryl concentrate containing 2.7 percent BeO by (1) sintering the beryl concentrate with limestone in a rotary kiln at about 1,150° C. and by (2) treating the sinter first with sulfuric acid and then with water to form and extract beryllium sulfate. About 80 percent of the beryllium was dissolved. The resulting leach liquor contained 2.4 grams of BeO, 20 grams of Al203, and 6 grams of Fe203 per liter. The laboratory solution contained much more aluminum and iron than a solution derived from treating 10 percent BeO concentrate, which is the standard raw material used by industry. Tests were made to determine the behavior of the solution toward alum purification and limestone neutralization both of which were employed industrially in conventional Degussa procedure.

Jan 1, 1962

As part of its research and development activities concerning coal mine operational/emergency communications sys terns, the Bureau of Mines commissioned several contractors to conduct electromagnetic (EM) noise studies and measurements that would aid the development of improved coal mine operational/emergency communications systems. The bulk of the noise studies and measurements were conducted in 1971. The Pittsburgh Mining and Safety Research Center (PMSRC) inherited the responsibility for monitoring the electromagnetic noise activities by mid-to-late 1971, and initiated a review and evaluation of the current and planned electromagnetic noise work. Arthur D. Little, Inc., (ADL) was asked by PMSRC to assist it in performing this review and evaluation by placing stronger emphasis on certain tasks of existing Contract No. H0122026. This technical memorandum report presents the findings, conclusions, and recommendations of our review and evaluation of the electromagnetic noise measurements of the five contractors we were asked to examine. Our review and evaluation effort included meetings and telephone discussions with technical staff of each contractor; serving as Technical Discussion Leader of a "Contractor's Round Table Meeting on EM Noise, Surface and Subsurface, Operating and Non-Operating Mines" called by the Bureau of Mines; examination and discussion of contractor reports and relevant open literature; sample verification calculations; and the documentation of our findings, conclusions, and recommendations by this report.

Jan 1, 1972

This report presents the results of reconnaissance-level investigations of the mill refuse disposal systems for 15 plants throw-heat the conterminous United States. The sites visited represent a cress section f the copper, iron, lead and zinc, and phosphate industries' practices in the field of fine-grained refuse disposal. The reconnaissance-level investigations were carried out to gather supplemental data to tae in-depth studies of Kennecott's Magma and Phelps Dodge's Morenci tailings deposits and Kennecott's Chino leaching dump. The various sites visited were classified according to the different systems and techniques used by the mining industry. The probable effects and relationships between site conditions and disposal methods were determined and evaluated to the extent feasible by a reconnaissance level investigation.

Jan 1, 1974

To alleviate the hazard to personnel and danger to equipment caused by fires on large, mobile vehicles. The Approach: A system which automatically senses a fire at its early stage of development, warns the driver of the danger, and activates fire extinguishers in the zone of combustion, How It Works: The automatic fire protection system utilizes both thermal and optical sensors to detect the heat or light given off by a fire in the area of concern (Fig. 1). The system warns the driver of the hazard and then automatically extinguishes the fire with pressurized S-C class powder. The system can also be activated manually from the operator's cab or from ground level. Further, the automatic sequencing of the system can be manually overridden by the driver if he determines that the fire sensors have malfunctioned to cause a false alarm.

Jan 1, 1974

By Ernest W. Hilton

The purpose of this investigation was to assess the environmental impact of the surface mining methods currently used in the steep-sloped areas of Central Appalachia: southern West Virginia, eastern Kentucky, southwestern Virginia and northeastern Tennessee. Comparisons are made between mountaintop/cross ridge mining, contour strip, augering and an innovative method surface shortwall mining which was attempted at Julian, West Virginia. Included in this final report are a discussion and analysis of current Appalachian production, reserves, and the extent of land affected on a county- by-county basis. Additionally, the seams within the steep sloped region have been assessed according to minimal standards of thickness, surrounding lithology, and areal extent to determine their amenability to surface shortwall mining. These seams have been tabulated with their ash, sulfur, and BTU content on a county-by county basis. Only minimal statements are made concerning quantity because of the narrow set of conditions required by the shortwall method. Other sections deal with the possible technical failings of an operational surface shortwall system based on field studies at shortwall operations, discussions with people experienced with shortwalls and research into ground control problems at sites where short- and longwall operations have been monitored. A final section details proposed additional research directions which the Bureau might take in the future.

Jan 1, 1979

This report is in fulfillment of Contract H0230031 awarded to Bituminous Coal Research, Inc., on May 23, 1973. The scope of work to be performed under this contract was divided into four phases: Phase I - Design, Phase II - Construction, Phase III - Field Demonstration, and Phase IV - Analysis and Final Report. During Phase I, an agreement was finalized with the Rochester and Pittsburgh Coal Co. for conducting field tests of the proposed shearer spray systems on a longwall panel in the company's Jane Mine in Indiana County, Pa. A drum was then designed which could be used on the Eickhoff shearer, Model EW170-L, being used on this longwall and which would utilize the following spray systems: 1. One spray nozzle located in front of each cutter bit with the jet directed at the cutting surface. 2. One spray nozzle located in back of each cutter bit with the jet directed at the back of the bit. 3. Standard Eickhoff nozzles located in a header along the drum scrolls. 4. A fixed header mounted on the shearer directly behind the drum to simulate the spray system originally used on the Eickhoff shearer.

Jan 1, 1976

By J. A. Kost

A survey of 80 coal producers was conducted to determine the extent and scope of respirable dust control research for underground coal mines and the current methods employed to control respirable dust. Results of the survey showed that proper face ventilation and an adequate water spray system are sufficient to comply with mandatory standards in room and pillar mining. Difficulties still exist with longwall equipment, auger miners and buring machines. In these cases, known dust control techniques are not sufficient to obtain compliance. Present state-of-the-art face ventilation and water systems were discussed in addition to the sampling program.

Jan 1, 1980

By Seth C. Schaefer

The Federal Bureau of Mines studied the Gibbs free energies of formation of chromous fluoride (CrF2), chromic fluoride (CrF3), and chromium (II,III) fluorides (CrF2.40 and CrF2.45) with high-temperature galvanic cells employing calcium fluoride doped with 1 mole-pct yttrium fluoride as the electrolyte. Free-energy changes were obtained from open-circuit potential measurements for the following cells: Cr, CrF2 // CaF2 // NiF2, Ni (a) NiO, NiF2 // CaF2 // CrF3 , Cr203 (b) CrF2 , CrF2.40 // CaF2 // NiF2, Ni (c) and CrF2 ?45 , CrF3 // CaF2 // NiF2, Ni (d) with the following overall reactions Cr(s) + NiF2 (s) = Ni(s) + CrF2 (s) (1) 3NiO(s) + 2CrF3 (s) = 3NiF2 (s) + Cr203 (s) (2) 5CrF2 (s) + NiF2 (s) = 5CrF2.4O (s) + Ni(s) (3) and 3.64CrF2.45 + NiF2 (s) = 3.64CrF3 (s) + Ni (s) . (4) These results were combined with the best available literature values of ?Gf° of NiF2, NiO, and Cr203 to deduce Gibbs free energies of formation for the chromium fluorides expressed as follows: ?Gf°(CrF2) = -179.31 + 24.33 X 10-3T ± 0.43 kcal-mole. (5) (858.1 - 964.9 K) ?Gf° (CrF3) _ -226.16 + 1.82 X 10-3T ± 0.79 kcal/mole (6) (880.8 - 957.8 K) ?Gf°(CrF2.40) _ -213.65 + 32.14 X 10-3T ± 0.44 kcal/mole (7) (0053.9 - 936.8 K) and ?Gf°(CrF2.45) _ -176.17 - 12.67 X 10-3T ± 0.80 kcal/mole (8) (875.1 - 937.6 K). Free energies and equilibrium fluorine pressures for three univariant and one bivariant equilibria are illustrated.

Jan 1, 1976

By K. P. Wang

Mining and metallurgy have had a long history in China, and resources there have always been considered promising. Under the People's Republic of China (PRC), a remarkable industrial renaissance is underway that should further gain momentum in the years ahead. Rapid development of minerals have not only brought the PRC prominence in industrialization, but also in world affairs. Chinese mineral developments, especially petroleum, have been increasingly in the news. Oil and gas may have great potential, but a very large coal industry is already in existence. The steel industry ranks fifth or sixth in the world. The PRC is also prominent in fertilizer, cement, and salt production. The export metals are well known. Also, the country is buying heavily in nonferrous base metals. The need to know and the intense interest in the subject have prompted this study. The world significance of Chinese minerals is pointed out. The history of growth and PRC's mineral supply position are reviewed. Evaluations are made of policy considerations and regional and technical factors affecting mineral development. PRC's mineral trade and efforts to obtain equipment, supplies, and know-how are assessed. Specific reviews are made of major mineral sectors, including coal and power, oil and gas, iron and steel, nonferrous metals, industrial minerals, and fertilizers and chemicals. The overall outlook is summarized.

Jan 1, 1975

By C. H. Riggs

"INTRODUCTION The injection of gas into the McClosky limestone in the adjoining, Griffin and New Harmony field in Indiana and Illinois and resulting increases in oil and gas production from this zone ore described in this report.Since 1911, the use of compressed air or as to increase oil production by supplementing natural reservoir energy has been widely adopted, and has resulted in the recovery of much additional oil, which otherwise would have been left underground. In many of the newer oil fields, including Griffin and New Harmony, a part of the compressed residue gas from natural gasoline plants is returned to the reservoir as a secondary method to increase oil and gasoline production. Part of the injected gas is stored underground for future use.By presenting data on many secondary recovery operations in a series of reports 5-9/ the Bureau of Mines has sought to stimulate interest in secondary recovery as a means of increasing oil recovery and current oil production for wartime needs. Most of the elder fields in the United States produce oil from sandstone reservoirs, and probably more than 90 percent of secondary recovery operations have been developed in oil bearing sandstones. During recent years, the volume of oil obtained by primary methods from limestone reservoirs has increased steadily, but as yet little has been done to recover, by secondary means,,the large volumes of oil left in limestone reservoirs when primary methods production are no longer profitable. Because of inherent differences in the origin and nature of the pore spaces between sandstones and limestones and because of differences in permeability and fluid content, secondary recovery methods, which are successful in sandstone-reservoirs, are not always applicable to limestones. Not much he been written concerning secondary recovery operations in limestone reservoirs, and few data are available to assist operators in developing such secondary recovery projects."

Jul 1, 1945

By Jennifer Riefenberg

A family of personal computer programs that calculate the Coal Mine Roof Rating (CMRR) has been developed by the U.S. Bureau of Mines. The CMRR rock mass classification system provides a link between the qualitative geologists' description of coal mine roof and the quantitive mine engineers' needs for mine design roof support selection, and hazard detection. The program CMRR is a user-friendly, interactive program into which raw field data are input. A CMRR is calculated and output along with two graphic displays. The first graphic display is a plan view trap with the CMRR's displayed on a color-coded scale. The second display shows a stratigraphic section of the bolted roof interval and its resultant CMRR. In addition, a Lotus 1-2-3 worksheet, computer file BOM-CMRR.WK3, has been developed for easy storage of field data. The worksheet includes four macros that automatically calculate CMRR's, store field test data in a database format, and print a two-page report of the field data and CMRR parameters. Production of summary port; for analysis of site-specific information are readily generated using Lotus 1-2-3 software. These programs help to facilitate the engineer in utilizing the CMRR in ground control studies.

Jan 1, 1994

The Bureau of Mines annually publishes statistical data reflecting technological trends in the minerals industry (metals and nonmetals except fuels). This report outlines recent developments and trends and the technology outlook for mining practices and metallurgical processing based on a review of the minerals industry during the past 2 years. A historical statistical series which indicates trends in the minerals industry has been extended with 1970 data. In addition, data are given from a 5-year Bureau of Mines cyclic canvass of froth flotation plants. Data for 1970 are compared with those of 1960 and 1965.

Jan 1, 1972

By Raymond P. Miller

This two volume report addresses slope stability of surface mine spoils within the Interior Coal Province. Sixteen (16) mines were visited, pertinent data and samples collected, and reported spoil instabilities back-analyzed. Laboratory test results are compared to back-analyzed material properties. Available methods of slope stability analysis are reviewed and evaluated with respect to application to mine spoil stability evaluation and prediction. Correlation and tentative relationships among spoil material properties, highwall conditions, mining equipment and procedures and empirical observations are presented. Slope stability sensitivity plots illustrate the relative significance of various input parameters on stability. Slope stability input parameters are correlated with site and mining conditions to identify the primary factors controlling spoil stability. Investigative methods, spoil stability enhancement techniques, spoil stability prediction procedures and future study areas are discussed. Appendices include a glossary of terms, annotated bibliography, details of mine visits, and detailed laboratory test procedures and results.

Jan 1, 1979

By V. F. Parry, W. S. Landers, John B. Goodman

"INTRODUCTION The object of this investigation was to demonstrate a satisfactory method of storing slack subbituminous coal in open pits in a manner,that would minimize the cause of the physical deterioration and would have a practical application.The storage of coal by industrial plants is to their advantage, since an adequate operating supplying of fuel is available at all times as insurance against transportation delays, shortages, and strikes. Furthermore, it is possible to participate in low seasonal freight rates and mine costs by permitting the railroads to utilize idle equipment and by taking advantage of the off-peak production at the mines. For a number of years, one of the larger beet-sugar companies operating in the Rocky Mountain region has taken advantage of the lower prices and seasonal production of subbituminous slack coal during the summer months and purchased a large proportion of its requirements for the annual winter campaign. This company, operating sugar-refining plants in the 1943 campaign, used 256,613 tons of subbituminous coal. Of this quantity, 166,636 tons was purchased during the off-peak season and stored for use during the winter. It is the practice of this concern to place coal purchased through the months of January to October in underwater storage for use in the beet-sugar campaign, which lasts from October to as late as, January. The beet-sugar refining ""campaign"" period starts immediately after the beginning of the beet harvest and lasts 60 to 70 days."

Aug 1, 1946

By F. R. Lee

When the Bureau of Mines was established in July 1910, one of the problems immediately attacked by the new organization was the development of standard, for the design and testing of electrical equipment that could be used without fear of initiating fires and explosions in underground coal mines. Research and investigation by Bureau personnel, supplemented by the published results of similar work by European mining authorities, led to the establishment of standards or "schedules." which guide manufacturers ill the design of many types of electrically operated machines and devices used in underground coal Mining. By issuing these standards, Bureau personnel establish the requirements to be met by such equipment before it tan be approved by the Bureau of Mines as permissible for use in gassy coal mines. Every 2 years the Bureau of Mines publishes a list of equipment that leas been accepted as approved or permissible during the preceding 2 calendar years. This is done to inform the mining industry of the availability y of the latest equip¬ment for safe use underground.

Jan 1, 1964

By G. L. Oldright

As sponge iron is much like porous, coarse sand, it is a tempting material to use in place of coarse scrap iron as a precipitant of metals, for scrap iron is relatively awkward to handle and exposes only a small amount of surface to pregnant solutions. The results of the experiments described in this bulletin are largely a record of the behavior of sponge iron as a precipitant of lead and copper under laboratory conditions comparable to those that would obtain in a commercial plant were it attempted to secure the maximum contact of surface between solution and precipitant. Physically, the study is largely one of the rates of diffusion of the metal ions in the solutions and through the metallic coatings surrounding the sponge iron particles. The practical objectives are to remove completely the valuable metals from solution and at the same time to obtain a precipitate of good grade. In order to fulfill this latter requirement, the precipitant should be almost completely consumed. These practical ends are usually secured by having the two substances involved pass each other counter-currently-that is, in such a manner as to have the strongest precipitant in contact with the most impoverished solution, and vice versa. EXPERIMENTS WITH LEAD SOLUTIONS In nearly all of the schemes involving the leaching of lead from its ores the metal has been put into solution as the chloride, and fairly concentrated liquors have been employed. The solubility of lead under such conditions is comparatively small at best; the hot pregnant liquors from which the metal is to be precipitated are then made nearly saturated with respect to lead, and only a very small amount of acid is used. Therefore it was not as necessary to learn the behavior of the sponge iron in precipitating lead from solutions of widely differing composition as to learn under what conditions, and with what mechanisms, this precipitation might be carried out most readily.

Jan 1, 1928

By BUREAU OF MINES

In 1948 the United States became a net importer of oil. Coupled with an unprecedented domestic production of 5,900,000 barrels daily, imports approximating 500,000 barrels made available a total supply of 6,400,000 barrels a day. Thus, by a herculean effort, the oil industry was able to meet an extraordinary demand at home and, in addition, to ship abroad almost 460,000 barrels daily of petroleum and products. The country’s oil position now differs greatly from that prevailing at the beginning of World War II. Then, actual oil production averaged about 4 million barrels a day, and productive capacity probably was greater than 5 million barrels a day. As the demand of the military and industrial machine grew with the rising tempo of the drive toward victory, the United States not only met its own needs but produced about two-thirds of the total oil requirements of the Allied Nations, excluding Russia. As a people, we can be deeply grateful that the Nation’s petroleum resources were adequate and sufficiently developed to support such a tremendous effort. Even in those critical hours when immediate needs were the paramount issues, a prudent Congress paused to contemplate the importance of an assured long-term supply of liquid fuels. From these deliberations came the Synthetic Liquid Fuels Act of 1944, which authorized research and development work on new sources of oil – coal, oil shale, and agricultural and forestry products. Since World War II, a civilian demand for 6 million barrels of petroleum products has become the order of the day. By drilling as many as 39,000 new wells a year, the production rate has increased enough to meet domestic requirements by a bare margin. Some imports were necessary, however, to fill both domestic and foreign demands, and these doubtless will increase. Is this policy of exploration within the United States and the development of oil in foreign countries adequate insurance for the fulfillment of our future national needs? This question has two aspects – one purely civilian and economic in character and the other significant from the standpoint of our national defense. There are now approximately 4,000 producing oil fields in this country. At first thought, it would appear that production could decline in a considerable number of these fields without materially affecting the overall daily output. However, 48 percent of the oil comes from only 111 major fields which contain 60 percent of the total proved domestic reserves. It is apparent, then, that the flow from large fields – having proved reserves of 100 million barrels or more each – must be sustained if daily production is to be kept at the present levels. Essentially, this means that new major fields must be discovered about as rapidly, or perhaps more rapidly, than the older ones lose productive capacity. From 1940 through 1947, only eight major fields with estimated reserves of more than 100 million barrels each were discovered and proved – an average of one such field a year. The total estimated reserve of these eight fields was less than 1 year’s supply at the present rate of use. As drilling continues, some existing fields ultimately will prove reserves larger than those now known. Without a pronounced increase in the number of major discoveries, however, the prospects for increasing our present productive level are not encouraging. Any gap that appears between domestic productive capacity and demand could be filled with supplies from proved oil resources abroad. Assuming cheap pipeline and tanker transportation to the United States, freedom from exorbitant taxes and charges...

Jan 1, 1949