Search Documents

By Alan Diaz Butron, Eng. Thierry Bernard

"In tunnel blasting the most challenging objective is definitively obtaining the maximum advanceassociated to a minimum overbreak. Achieving 100% of advance with no overbreak is the targetchallenge by Chavimochic Consortium. Chavimochic Special Project is an irrigation system that extends throughout much of the coast of the La Libertad Region, on the north coast of Peru. In 2012, it began management for construction of the third and last stage of CHAVIMOCHIC to irrigate lands of Chicama Valley, North of Trujillo. This project of 13 Km (8 mi) of various tunnels, it's a combination of technology and daily optimization by experienced people, which allow to accomplish the objective. Achieving this advance with no overbreak provide a huge saving on time. This paper describes the method, technology used, and the results obtained on more than 600 blasts done with conventional initiation system on the first 3 km (1.86 mi)."

Jan 1, 2017

By Derek T. Novotny

Blasting cap precision is of major importance to advanced blast design. New technologies have introduced the use of microchips within detonator casings in the hope that the electronic control of the timing element will increase the accuracy of the cap and therefore improve the results of perimeter control blasting applications. The electronic detonators have proven to be accurate in timing tests done to date. They boast cap scatter results to microsecond accuracy, but the question is, does this degree of accuracy actually prove to be beneficial during practical use in the industry, or are conventional technologies applicable.

Jan 1, 1998

By Leslie C. Taylor, Scott A. Yamada, William L. Fourney

Previous studies have shown that the pressure load on a target by a buried explosive charge is not smoothly distributed. The effort reported here was undertaken to explore the mechanisms believed to cause this uneven pressure distribution: jets from the surface originating in instabilities caused by the explosive shockwave interacting with surface irregularities. Small-scale tests using conical, hemispherical, and cylindrical indentations in the sand surface above a buried charge were conducted to identify trends in the velocity and form of the resulting jets. In these tests, the most important factor affecting the resulting jets was the distance between the bottom of the indentation and the top of the charge. Cylindrical indentations resulted in higher jet velocities than those from comparable hemispherical and conical indentations.

Jan 1, 2012

By Duncan Chalmers, Rob Nowell, Miguel Araos

Australian underground mines produce in excess of 60 mtpa of coal. Most of these use the longwall method, and they require the use permitted explosives (which are called “permissible” in other countries) for challenges that appear during the day-to-day activities. To obtain the approval for these explosives, they should pass Testing Memorandum #2 (TM-2), which sets out the test required for each category of permitted explosive. These categories are P1, P3, and P5. With P5 being unrestricted use and P3 and P1 have conditional use in underground mines. The TM-2 test was originally set up for NG-based permitted products around 1900. With the closing of NG plants around the world, ammonium nitrate explosives were the natural replacement, and therefore these explosives need to pass the TM2. Australia does have a P1-emulsion based explosive available. For high-risk scenarios (like blasting coal), no P5 explosives are available. The lack of P5 explosives has been prolonged for more than 25 years, since the phasing out of nitroglycerine-based permitted explosive products around the world. The main problem has been that when emulsion based permitted products are tested in the deflagration cannon, the results obtained were not considered in the TM2 criteria and therefore the tests were invalid. A research work on permitted explosives began in 2005 funded by the Australian Coal Association Research Program (ACARP). The aim of the project was to address the lack of P5-type permitted explosive (and, potentially develop them further, i.e., develop safer explosives) and understand the behaviour of emulsion explosive and the results they presented in the tests. Both bureaucratic and technical barriers appeared along the way. On the bureaucracy side, the facility was shut down, reopened, and shut down again. In view of these difficulties, assistance was sought overseas. On the technical side, from the very start the results of the tests when using emulsion-based permitted explosives were not established in the criteria, ignitions occurred for trial samples that were expected to be P5-type, etc. The aim of this document is to present the painful journey in the Australian industry to have a P5-type emulsion-based permitted explosive, for use in UG coal. Also, the technical learning acquired about emulsion explosives and the ignition path of mixtures methane / air will be shown.

Jan 21, 2025

By Marco Larghi, Jurg Knobel, Braden Schmidt

Remote Avalanche Control Systems (RACS) which uses solid explosives has been used in Europe since 1996 and North America since 1999. With large destructive avalanches in transportation corridors, various States and Provinces have started implementing RACS into their summer construction projects to minimize traffic shutdowns. Since 2014 in North America, many of the projects are requiring the RACS deployment boxes to be removable by light duty helicopter for loading and summer storage. This is to further remove workers from the mountain tops, where inclement weather and Occupational Health and Safety concerns are widespread. We did not believe the method of flying primed charges under a helicopter was safe, so we developed a new charge container to deal with the issue.

Feb 1, 2020

By Bill Loviza, Jimmy Sanders

This report is not everything we would like it to be. Access to information concerning unresolved legal actions is a sensitive matter. Obtaining the information presented in this report was a challenge alone. The Tennessee Department of Commerce and Insurance, Division of Fire Prevention, the firms and individuals that elected to share information did so with various assurances of nondisclosure, confidentiality or anonymity. All those providing information did so with the expectation that the industry and ultimately the public would benefit from this effort. We offer special thanks to Assistant Commissioner, Fire Prevention, Emmett Turner, recently retired Director, Bomb and Arson, Dick Gardner and Director, Codes Enforcement, Randy Safer for support that made this endeavor possible. We make no claim with regard to being a scientific study. We did the best we could with available information. Our task was one of assembly, sorting and reporting. Where collateral information was available we used it.

Jan 1, 2004

By Abraham Lindo

Taboguilla is a small island located 10 miles outside the Panama Canal Pacific Entrance. In 2002 a fuel distribution facility was installed in order to supply fuel to vessels passing thru the canal. The current capacity of the tank farm is equivalent to 1,100,000 barrels. The demand for marine diesel at this location still exceeds the current capacity, thus an expansion project is currently underway to increase the available space for diesel tanks. There is a total of 800,000 cubic meters to be excavated in order to create the new space. 400,000 cubic meters of that total is basalt rock which will need to be blasted

Jan 1, 2011

By Ambrose Buchanan, Rob Farnfield, Charles Adcock

Beginning on 7th September 1940 the City of London was subjected to 57 consecutive days of bombing in what became known as the ‘London Blitz’. To commemorate the 70th anniversary of this event a television series was commissioned that required the open detonation of World War 2 equivalent bombs close to purpose built structures constructed using period design and materials. The structures were built on a remote test facility in the North of England that is able to fire large quantities of explosive in the air.

Jan 1, 2011

By Darío Innamorati, Jorge Oliva

Cerro Vanguardia is a known gold and silver deposit located in the province of Santa Cruz, Argentina. The mine has been in operation since 1998 and is thought to be one of the most important mines in Patagonia. More than 102 epithermal quartz veins have been identified in the area, with variable lengths, thicknesses, orientations and dips that constitute what is possibly one of the most extensive outcropping vein systems on earth. Veins are vertical and have variable depth. For this reason, the deposit is currently mined with a variety of extraction methods. This operation is made up of more than 60 open pits and 20 underground access ramps to exploit the deepest high grade narrow veins. This study is focused on the combination of underground exploitation with open pit blasting. That is, those production stopes in the upper levels of underground mines and their interaction with the damage levels in the final slope of open pit mines, as well as in the study of the impact of the generation of vibrations from the blasting of open pit mines and their influence on underground mines. Considering the current stage of the mine, after 20 years of operation, Cerro Vanguardia faces the need to mine deeper deposits in the face of increasing costs and declining grades. For this reason, it is essential to study the interaction of these exploitations. From a personnel safety point of view, this interaction must be well coordinated so as not to affect people and equipment. Likewise, the generation of vibrations due to blasting must be studied, which would produce new cracks, potentially generating overbreak and dilution. The main objective of this study is to determine the possible causes and influences of the blasting interaction in open pit and underground mines, seeking an optimization of the blasting process and a safety standard for personnel and equipment. To achieve these goals, this study includes a vibration monitoring plan to analyze the charge performance and determine rock constants. With the use of specialized software, damage modelling and simulations are used to determine values of damage in order to reduce overbreak. In addition, this plan contemplates the estimation of flyrock in blasting where underground work is connected to the surface, determining safety distances when carrying out a blast.

Jan 21, 2025

By B Mohanty, M Alam, F Gauthuer

A series of eleven full-scale production blasts has been earned out in a limestone quarry to study the effect of delay interval and its precision on overall blasting performance. The quarry employed ANFO and cartridged aluminized emulsion in 75 mm diameter boreholes with 2.6 m burden and 2.9 m spacing on a 6.7 m bench. Both V-cut and echelon designs were studied. The types of detonators tested were regular short period electric detonators with expanding delay intervals, a more precise pyrotechnic-based electric detonator (EXADET) with a fixed (25 ms) delay interval, and the ultra-high precision electronic delay detonator (EDD) with constant (but site-selectable) delay interval. The various techniques employed to assess the blast results are described, and the performance of the three types of detonators compared. The use of both EXADET and EDD lead to improved blast results in echelon design. Of the three delay intervals (25 ms, 38 ms, and 50 ms) studied, the best results were obtained with EDD with a 38 ms delay interval, which translates into a delay of 38 ms/m of effective burden. The results also show the need for modification of current V-cut delay designs to derive full benefits from these high precision detonators.

Jan 1, 1991

By Richard J. Mainiero, Michael S. Wieland, Harry C. Verakis

The Bureau of Mines, U.S. Department of the Interior, has been conducting research on delay blasting in underground coal mines in support of the efforts of Mine Safety and Health Administration (MSHA), U.S. Department of Labor, to revise coal mine blasting regulations. Part of the research centered on developing an understanding of the factors that lead to misfires of permissible explosives. Research was conducted to determine whether frequency of misfires was related to borehole spacing. For a wide variety of permissible explosives, misfires were observed for about 50 X of the holes at 45-cm (18-in) spacing. Misfires were also observed for 60-cm (24-in) spacing, but the frequency of misfires was much lower than observed for the 45-cm (18-in) spacing. The Bureau has recommended that hole spacings of less than 60 cm (24 in) be prohibited.

Jan 1, 1986

By J. Silva, M. Kotraba, F. Pontanilla

Blasting is the application of highly complex science that, in some cases, could be viewed as an art. Many variables are involved in a blast, including geology, pattern design, timing and firing sequence, and explosives selection. Assuming that better results can be achieved by only increasing the powder factor is inaccurate. The Drill-to-Mill (D2M) concept has been in the mining industry for over two decades. The D2M approach is commonly viewed in an oversimplified manner, assuming that by simply increasing drilling and the amount of explosives used (both of which add operational costs), the downstream value will be created. An optimized D2M initiative should combine the smart application of explosives at the beginning of the mining process, matching the dynamic properties of the rock to the explosive selected to improve the efficiency of the energy created by the explosive to the rock mass being blasted, and to bring benefits to the mining operation across the entire mining and processing value-chain. This paper reviews the principles behind matching the shock impedance of the rock and the explosive and compares the traditional use of explosives versus the smart application for two hypothetical blasts.

Jan 1, 2024

By Randy Wheeler

In recent years the issue of seismograph calibration and accuracy has been a major focal point of the ISEE Blast Vibration and Seismograph Section. In fact, questions concerning the consistency and reliability of seismograph measurements essentially led to the development of this ISEE section. One of the early actions of the section involved the development of “Field Practice Guidelines” for the use of seismographs. These guidelines specifically state that “Placement and coupling of the vibration sensor are the two most important factors to ensure accurate ground vibration recordings.” This paper will address the results obtained from using different coupling methods to record vibration and airblast levels generated from production blasting in a limestone quarry. The data obtained clearly indicate that seismometer burial provides the best coupling for recording ground vibrations. Microphone height has also been an issue regarding the accuracy of recorded airblast levels. The data we obtained indicates that microphone height is not a significant factor.

Jan 1, 2004

By John Vynne

BHP’s Navajo coal mine installed drill monitoring and high precision navigation systems on their three overburden drills during 2002 and 2003. Details of the DrillNav system hardware and reporting system will be discussed, as well as the significant benefits Navajo has achieved since the systems were installed. Navajo is not satisfied with the current results and plan additional upgrades to the systems. In addition, Navajo plan to integrate the data from their drill systems with data from other systems to achieve even greater increases in drill productivity and to reduce overall mining costs.

Jan 1, 2007

By Jane Wright, Brent Blanchard

Question: When it comes to demolition projects, what could be more demanding than asking a blaster to explosively demolish a stubby, heavily-reinforced concrete structure in the heart of a third-world country? Answer: Asking them to fell only half. Such was the charge recently put forth to Controlled Demolition Group (CDG), Yorkshire, UK when they were called to Casablanca, Morocco to provide a stunning demolition effect for the upcoming Universal Pictures film Spy Game, starring Robert Redford and Brad Pitt. Director Tony Scott (True Romance, Enemy of the State) contacted the renowned demolition firm after seeing their work on television and receiving recommendations from explosives manufacturers. The film’s producers then asked the CDG team if they could bring down half of an apartment block as part of a dramatic suicide bomber sequence.

Jan 1, 2002

By Barbara Rutter, Shonn Kevin McNeil

"This study discusses how a prototype was built to measure the sonic velocity in powdered explosives.The sonic velocity of an explosive is a benchmark to determine if the explosive deflagrates or detonates;however, little work has been done to determine this value for powdered explosives. This paperdiscusses the results of the initial prototyping tests where two known mediums, air and water, were used for validation. The prototype did record the sonic velocity within the known velocity ranges of air and water; however, a few depths did not fall into this range. This prototype could be used for testinggranular materials."

Jan 1, 2017

By Tapas Kumar Mukherjee, Sujit Kumar, Sanjay Kumar Singh

This paper dwells on the epic blast conducted at Tata Steel’s captive coal mine in India and the insights drawn from it. Optimal blast design parameters had to be ascertained for operating benches (6.56 yards (6 meters) to 16.40 yards (15 meters)) where shovels and mining pay-loaders are deployed. Better fragmentation and suitable muck profile with controlled vibration levels were the pre-requisites. The landmark blast was carried out at Quarry-AB, West Bokaro on 17th March 2017. The colossal blast was done with 275 US ton (250 tonnes) of explosives poured down 1074 drill holes of 6.5 inch (165 mm) diameter. This blast is unique from the perspective of vibration control as it was conducted near local villages situated beyond 546 yards (500 meters) but within 601 yards (550 meters)) from the blast site. The entire array of preparatory activities had been successfully and impeccably executed within the same day. The optimization was achieved through meticulous coordination between TSL team, M/s Solar and M/s IEL. When a rock is blasted, numerous interactions occur among granular particles which are impacted by rock mass properties, explosives properties, blasting geometry and the detonation timings. Optimized use of resources requires a better understanding of these interactions. Extensive field studies have shown that blast fragmentation and suitable muck profile influences the performance of downstream processes in a mine. Consequently, profitability of whole mining operation can be greatly improved through optimized fragmentation. For arriving at the best blast geometry, several blasts were conducted with differing ‘burden and spacing’ design and charging pattern at various loading benches of the mine. Eventually, the largest ever blast was successfully carried out. This accomplishment is the culmination of the insights derived, confidence built, and expertise evolved through a progression of larger blasts conducted earlier (202 US tons (184 tonnes) and 143 US tons (130 tonnes) respectively) by the same team. All blast parameters were within the recommended level and no adverse impact on nearby structures was evidenced. In-the hole VOD of different explosives was determined and placement of boosters was standardized. The signature blasts were conducted to optimize the delay interval between the holes in a row and between the rows. Blasting parameters were fine-tuned in alignment with the desired fragmentation level and muck pile profile conducive to smooth and expeditious loading and hauling by mining HEMM. Rock fragmentation analyses were carried out using photo-analysis system. The insights gained from this blast would serve as the cynosure for planning and carrying out more such blasts with highly optimized parameters in the future with the intent of improving mining efficiency and productivity

Jan 1, 2019

By D. S. Scovira, T. Gustavsson

Exiting WW2 (mid-1940s), the potential of nitrates (ammonium nitrate, calcium nitrate, sodium nitrate) and hydrogen peroxide for application as a commercial explosives for mining, construction, and other industrial purposes both became known. The technology stream advanced the development and uptake of nitrate based explosives to the point that they are the current global standard for blasting. Today, environmental issues are shaping the strategic agenda across various industries. Most global mineral resource, construction houses, and explosive manufacturers have publicly announced ESG carbon reduction commitments in support of COP26 Net Zero 2050. The mid-2010s saw a renewed interest in hydrogen peroxide explosives to eliminate NOx fume. Carbon reduction initiatives in the early 2020s provided additional impetus to investigate hydrogen peroxide based explosives for industrial use. Hypex Bio has recently pioneered the formulation, manufacture, and end-use delivery of a Hydrogen Peroxide Emulsion (HPE) on an industrial scale. The HPE is composed primarily of hydrogen peroxide (H2O2) plus a lesser amount of fuel and emulsifier phase. The base HPE is produced in a low energy intensity modular plant using industry proven mixing techniques. The base HPE is a white, highly viscous emulsion that is similar in consistency to base nitrate emulsions. To enable end blasting use, a mobile charging unit gases the base HPE to a detonable density. The HPE is compatible with current priming and initiation systems. Hydrogen peroxide explosives offer a significant reduction in total carbon emission as compared to nitrate based explosives. The production of ammonium nitrate (AN) emulsion is energy-intensive and not carbon neutral. Based on the EU Average and for the oxidizer phase only, 1 kg [2.2 lb] of AN emulsion emits 2.3 kg [5.1 lb] of CO2 as compared to the production of hydrogen peroxide emulsion that results in 0.23 kg [0.5 lb] of CO2. This is a difference of 90%. HPE contains no nitrates and does not generate post blast nitrous oxides (NOx). HPE generates no aqueous nitrate or ammonia pollution and is a solution to meeting increasingly regulated mine site water discharge limits. Hypex Bio recently conducted a successful underground HPE evaluation with a major mining company in Sweden. HPE blast designs were the same as those done with nitrate based emulsions. Rock breakage, advance, muck displacement, and excavator performance were equivalent. Ventilation and re-entry times were reduced. The mining company has expressed further interest in assessing HPE and is demonstrating industrial leadership by exploring this transformative explosive technology

Jan 1, 2024

By N. Skopak, C. Aimone-Martin, J. Redyke, B. O. Meins

PipeBlast is a spreadsheet-based calculator based on research conducted by Southwest Research Institute (SwRI), used by the pipeline industry to determine if proposed blasting planned near existing pipelines can be safely executed. The two factors determining “safe” are blast-induced pipe wall hoop stresses and predicted peak particle velocity (PPV) at the pipeline. Although methodology used to predict hoop stresses is somewhat sound, predicted PPV amplitudes are highly exaggerated based on inappropriate attenuation models developed using spherical explosive charges of limited charge weights, placed in soil adjacent to model pipelines that do not represent rock blasting. Hence, pipeline companies readily reject well-design blasts and limit scaled distances far beyond what is reasonable and cost-effective to pipeline owners. Full-scale trench blasting in rock was conducted near a 24in (711mm) diameter operating API 5L X70 grade steel pipeline in Texas to compare PipeBlast model predictions with a Ground Strain Model (GSM) based on field measurements of ground motions on the surface and at the pipeline springline. Results of the GSM were compared with pipeline strains measured using wire gauges mounted on the Springline. The comparative results showed that a site-specific velocity propagation model provided good estimates of ground strains that are replicated on the pipeline walls in terms of hoop and longitudinal strains. Trench blasting 28ft (8.5m) from the pipeline produced ground motions of 7.6in/s (193mm/s). At this ground motion amplitude, the factor of safety defined as the allowable stress divided by the combined operating and blasting hoop stresses was reduce from 3.04 in the absence of blasting to 2.98. This paper explains the research and findings on which PipeBlast is based and presents an alternative approach to predicting blast-induced pipe wall stresses based on site-specific velocity propagation measurements and a ground strain model.

Jan 1, 2024

By Jean-Francois Lagueux, Andre Pomerleau

Goldex Mine is an underground mine located near the town of Val-d’Or. Multiple innovations were required to work the mine. Due to its low grade, it was important to develop a bulk mining method to economically extract the ore. The method used is a combination between shrinkage stope and long holes stope methods. This modified method is more than adequate; however, all of the ore body must be liberated in a very short period of time. Therefore, to bring down 23.0 M tonne (25.3 M ton) of ore, large blasts up to 1.8 M tonne (2.0 M ton) are required. The situation is also complicated by the fact that the mine is located in a residential area. No less that 40 homes are built within a 1 km (0.62 mile) radius of the mine site.

Jan 1, 2011