Search Documents

By Aubrey Mainza, Malcolm S. Powell

"A hydrocyclone with two vortex finders, named the three-product cyclone, has been successfully tested in the Platinum industry for dealing with the dense chromite found in UG2 ores. This dense component preferentially reports to the cyclone underflow, resulting in an over-ground fine chromite component in the final product. The dense media effect caused by a high chromite concentration in the cyclone feed produces a coarsening of the cyclone overflow, which results in loss of recovery through over-size material in the float feed. The fine barren particles of chromite that report to the overflow are recovered through entrainment in the flotation process, resulting in detrimental contamination of the slag produced from the concentrate.With the three-product cyclone a middlings product has been extracted that has a higher concentration of fine chromite. This volumetric stream flow represents a small percentage of the total cyclone feed and it is thus possible to treat it separately via fine screening to remove the fine chromite from the system and recover coarse silica."

Jan 1, 2003

By J. Faitli

The Lake Balaton is the biggest and for many reasons the most important lake in Hungary. To preserve its healthy nature it is necessary to remove the accumulated mud time to time, similarly to the many living waters, lakes and rivers everywhere. Typical existing technologies (mechanical, hydraulic) require large depositional areas, where the removed slurry and mud is dewatered through very long time. One problem is the non existence of an economical mud thickening technology. Another major problem is that current methods remove the sand fraction with the mud as well. Many times sand has to be complemented from outer sources to endanger the natural balance of the living water. By the financial support of the NKFP 3A/068/2004 Hungarian Research Project our consortium has been looking for the solution to the above mentioned problems. The original ideas of the project were: 1. Sand should be separated and returned to the water by hydrocyclon; 2. New mud thickener should be developed based on the principle that vibrating rods can force settling and packing of mud particles. The work was started by fundamental research with different samples from Lake Balaton and River Bodrog. An automated settling column (45L) has been built for the investigation of the effect of vibrating rods on the settling behavior of suspensions. An optical sensor has been developed by with the settling curve (height of settling slurry as function of time) can be automatically measured. Different vibrating methods and parameters have been tested by the application of a linear motor and mechanical eccentric drive. On the basis of the fundamental research a new thickener, called the rod ? lamella thickener has been developed and an industrial size (50m3/h) mud removing technology has been built. Main parts of the technology are the traditional dredging barge and the thickening technology. The thickening and sand separation technology is tugged by the dredging ship. Its main elements are the homogenization tank, slurry pump, hydrocyclon and the rod ? lamella thickener. In this unit lamellas carry out pre-thickening, then vibrating rods further increase the concentration. The thickened mud is transported out by a screw - of which revolution number is precisely controlled - against a spring supported valve. Paper reports about the design, building, water probe and on-site tests of this mud removing technology. Two new patents had been presented, one is about the rod ? lamella thickener and the other is about the mud removing technology with sand separation.

Jan 1, 2014

By J. Lindström, J. Hamuyuni, M. Lundström, J. Aromaa

"The rising demand for metals today, coupled with the scarcity of primary sources for raw materials threatens both technological advancements and industrial manufacturing. In order to meet the demand, metals and other resources trapped in waste streams, have to be harnessed. This philosophy supports circular economy, where metals and other resources are kept in a closed loop. The pickling acid recovery system of most stainless steel production is one such example where the dissolved metals such as iron, nickel and chromium are currently not completely recovered due to the limitations of the current technologies. The aim of this study was to assess the available metals recovery methods from extremely concentrated acids. The main aim is to simultaneously recover metals and keep sulphuric acid reusable in acid circulation process. From the available literature, the most promising methods were chosen for laboratory experiments. Based on experimental work, the results and observations of electrodeposition, solvent extraction, and freeze crystallization are provided. KEYWORDS Pickling acid, metal recovery, solvent extraction, cathodic polarization, Freeze crystallization. INTRODUCTION Pickling in stainless steel production is an essential surface treatment process (Regel-Rosocka, M. (2010); Agrawal and Sahu, 2009). It is applied for removing surface films such as oxides and chromium-depleted layers to improve the corrosion resistance and surface finish of steel (Regel-Rosocka, 2010). Whilst the process greatly improves the surface finish of the stainless steel, it generates large amount of used acid, containing dissolved metals including chromium, iron, and nickel (Agrawal and Sahu, 2009). Recovery of acid is common practice for most steel producing industries (Nyman and Koivunen, 1986). In this work, acid regeneration process is investigated so as to simultaneously reusing sulfuric acid and recovering the dissolved metals. Recovery of valuable metals even in very small amounts would also bring additional revenue to the steel production industry. At a time when metal production has also been challenged by lack of natural resources for raw materials, secondary sources for metals such as the acid pickling process therefore, have greater potential as supplements. From earlier studies, electrodeposition (Giovanardi and Orlando, 2011; Kuznetsov et al., 200; Rögener et al., 2012; Surviliene et al., 2006), solvent extraction (Alguacil and López 1996; Haghshenas et al., 2009; Kesieme et al., 2013) and freeze crystallization (Beyer et al.,2003; Hasan et al.,2017; Van der Ham et al., 1999) are some of the most established potential methods. Earlier studies have also shown that simultaneous recovery of acid and metals would require combination of different methods. This is primarily due to the nature of very stable metal containing complex compounds formed during pickling. These complexes must be broken down to free the metals for further recovery processes."

Jan 1, 2018

In this paper, the recovery of copper minerals and molybdenite in the rougher/scavenger banks of two separate mineral processing plants is compared with recovery in laboratory (batch) cells. A number of metallurgical surveys were conducted in two plants treating porphyry copper and molyb-denum ore. Batch flotation tests were performed on plant conditioned flotation feed slurry, in parallel with the plant metallurgical surveys. The effect of flotation feed density on recovery of copper minerals and molybdenite in the plant and batch laboratory cells was investigated. Changes in flotation pulp density had little effect on copper mineral recovery, in both plant and laboratory cells. The ultimate recovery for molybdenite, on the contrary, increased considerably when the pulp density was reduced, both at plant and laboratory scale. Recovery of copper minerals in the plant and laboratory cells was comparable, while molybdenite recovery in laboratory flotation cells was 3%~13% higher than in plant. It is hypothesised that the flotation rate of molybdenite is sensitive to cell hydrodynamic conditions (i.e. local turbulent energy dissipation) more than the flotation rate of copper. The flotation behaviour of molybdenite particles is likely to be predominantly controlled by bubble-particle collision frequency, which is enhanced in high local turbulent energy dissipation environment. For chalcopyrite, the flotation recovery is mostly determined by attachment and stability efficiencies. An increase in local turbulent energy dissipation, while increasing collision efficiency, may negatively impact on attachment and stability efficiencies. The outcomes may have a considerable impact on increasing molybdenite recovery from porphyry ores.

Jan 1, 2014

By R. Batterham

"The history of mineral processing is indeed long and has always been tied to mining methods of the day. While many new processes and devices have been developed, the most significant trend in recent times has been the ever increasing scale of operations. There is serious doubt this ongoing trend is enough to match the global trend of falling grades and rising energy demands needed for mineral processing. As well we see that globally, the social licence to operate for mining (and hence mineral processing) is far from secure. Indeed, some argue that mining as we know it is dying and in the future, mining will be much more environmentally secure, even to the extent of insisting upon “in place” recovery and only bringing to the surface the valued product. In this paper we comment on the ramifications of broader uptake of more sustainable mining for mineral processing methods and address the specific question of whether recent progress in in place recovery will lead to a timely breakthrough. The answer proposed is that this is possible in the next 10 - 20 years but in the meantime, the focus is just as likely to be on removal of waste much earlier in circuits. Either way, mineral processing as we know it will change significantly. INTRODUCTION Mineral processing has a long history well covered in a recent publication (Habashi, 2006) who points out “the ancient Egyptians knew already that it would be easier to melt an earth rich in gold particles than another which is poor. As a result, all efforts were made to enrich the gold by washing away the light gangue minerals. Similarly, another ancient method for enriching gold particles from a river stream was by means of fleece, hence the Greek myth of the “golden fleece”. Since the middle ages, striving for improved economics has driven a string of innovative developments in milling and separation. The reader is again referred to the informative and illustrative text by Habashi."

Jan 1, 2018

By Hillary Williams, Ronghao Li, Christopher Marion, Kristian E. Waters, Devin Hundt

"Zircon is an important mineral for ceramic, foundry, casting, and refractory applications; and it is the worlds primary source for zirconium. Zircon can also contain large and valuable proportions of other valuable metals, such as rare earth elements and hafnium. The Nechalcho deposit (Northwest Territories, Canad), is a hard rock REE deposit, which looks to recover zircon for its Zr and REE content. In this deposit, zircon is finely disseminated and associated with predominately silicate gangue minerals. Most of the work to date has focused on the beneficiation of mineral sand deposit, which typically remove silicate gangue minerals through physical separation steps. Therefore, the separation of zircon from silicate gangue, such as quartz, by flotation, has received little attention. This work used zeta potential measurements and microflotation experiments to understand the interaction between zircon and six different collectors (sodium oleate, sodium dodecyl sulphate, dodecylamine, SM 15, K-octyl hydroxamate and Florrea 7510). The results were compared with those of quartz. This study indicated that selective separation of zircon from quartz without the use of selective depressants or activators is likely challenging. The findings suggested sodium oleate and SM 15 only offered selective flotation of zircon in highly acidic conditions. Separation by the flotation of quartz is possible using sodium dodecyl sulphate, dodecylamine and K-octylhydroxamate. However, selective separation is highly dependant on collector dosage, for dodecylamine, and the selective activation of quartz, for sodium dodecyl sulphate and K-octyl hydroximate. Florrea 7510 offered poor recoveries for both zircon and quartz.INTRODUCTIONZircon (ZrSiO2) is a nesosilicate mineral which has a wide variety of applications, due to its hardness, opaqueness and resistance to heat and corrosion. Its major end uses are in ceramic, foundry, casting, and refractory applications (Bedinger, 2017). Zircon is also the most abundant zirconium (Zr) bearing mineral in the earths crust and is the principal economic source of Zr (primarily used in alloys for heat and corrosion resistance) and zirconia (ZrO2) (primarily used in ceramics) (Bedinger, 2017; Milnes and Fitzpatrick, 1989). Zircon forms in silicate melts and can often contain large proportions of other valuable metals such as rare earth elements (REE), and hafnium (zircon is the primary source of hafnium) (Bedinger, 2017; Belousova et al., 2002; Orlova, 2007). A common chemical formula showing the range of substitution in zircon is (Zr,Hf,Th,U,REE,Ca,Fe,Nb,Ta)(Si,P)O4 (Orlova, 2007)."

Jan 1, 2018

By L. J. Li, Q. Zhang, Z. H. Liu, Q. L. Chen

Phosphogypsum (PG) is an industrial waste from the production of phosphate fertilizer. The utilization of PG is restricted by its containing impurities, and the pretreatment is crucial to eliminating these impurities. The purpose of the research is to recycle pretreatment PG as raw material for preparation of a-calcium sulfate hemihydrate (a-HH) by salt solution method. The effect of pretreatment technologies of lime neutralization and washing on dehydration rate, phase composition and morphology evolution of a-HH were investigated by crystal water content analysis, XRD and SEM. Furthermore, the change of pH in the reaction process was also discussed in detail. The results show that the dehydration rate of conversion PG to a-HH increases and the corresponding induction period, crystal growth period and total time decrease with an increase in CaO dosage from 0.2% to 0.6%. In the presence of 0.4% CaO or 0.6% CaO, the a-HH presents a long hexagon-prism-shaped crystal with a purity of 94%, and the end face of a-HH presents polyhedron. The system pH sharply decreases with the reaction time under different CaO dosage, and the pH variation from the initial alkalinity to acidity. The main reason is that as the co-crystallized phosphorus dissolved and released HPO42-, and with the pH decreasing to 4-5, HPO42- transformed into H2PO4-. The dehydration rate of washing PG is lower than that of original PG. Compared with the original PG, a-HH with the larger width and smaller aspect ratio can be achieved from the pretreatment PG subjected to lime neutralization and washing, meanwhile the crystal surface is more smooth.

Jan 1, 2018

By Fang Liu, Xin Tan, Zhong-ming Wang, Yan-bo Shang, Jie Zhao

"The flotation separation of sulphides bulk concentrate containing Cu, Zn, Mo and Bi, which was obtained by both table-flotation of gross sand of gravity separation of wolframite and bulk flotation of wolframite slimes using butyl xanthate and oil No. 2, etc., has been conducted by using the cyanide process in the tungsten concentrator. The process has problems of high reagents consumption (25 tonne of cyanide dosage per year) and mineral processing cost (800~1000 RMB reagents cost per tonne of by-product concentrates), high mutual containing loss in the by-product concentrates and serious environmental pollution caused by lots of cyanide-containing wastewater. In order to solve this problem, a new cyanide-free separation technology is studied, which is used to process this sulphides bulk concentrate with 8.68% Cu, 8.98% Zn, 0.26% Mo, 1.58% Bi and 40.12% S. The results of the closed circuit test show that Cu, Zn, Mo and Bi can effectively be separated from this sulphide minerals concentrate by using the reasonable flotation-gravity flowsheet, high-efficiency collectors and regulators simultaneously. The metallurgical recovery and concentrate grade are as follows: molybdenum recovery is 94.63% with 50.62% Mo content; copper recovery is 85.18% with 29.29% Cu content; zinc recovery is 75.92% with 46.49% Zn content; total Bi recovery is 65.08% with 16.86% Bi content. The new technology is an alternative to the cyanide process due to its low cost for reagents, satisfying separation results and economic profits, and solves the problem of environmental pollution caused by the use of large quantities of cyanide. Some important parameters in separating the Cu-Zn-Mo-Bi sulphides concentrate are also introduced in this paper. This study provides pretty good technical support for separating the polymetallic sulphide ores containing Cu, Zn, Mo and Bi by cyanide-free technique."

Jan 1, 2014

By Q. Shi

An investigation into the hydrophobic aggregation of ultrafine smithsonite in surfactant solution has been undertaken through a combination of hydrophobic flocculation experiments, zeta potential measurements, surface tension measurements, and contact angle measurements. The experimental results have revealed that the behaviors of hydrophobic aggregation were closely correlated with the particle hydrophobicity, but they were not lowered byte change of the particle surface charges due to surfactants adsorption. On the other hand, the liquid (solution) surface tension (?LV) plays an important role in hydrophobic aggregation, and the hydrophobic aggregation could not occur below the critical liquid (solution) surface tension (?c). Meanwhile, this flocculation has been observed to require sufficient stirring strength and magnitudes of kinetic energy input to achieve the maximum aggregation degree. From the microflotation results, it has been found that the flotation kinetics response of smithsonite fines is markedly improved due to sufficient stirring strength, and the stirring strength influenced the floc flotation in a manner quite similar to their influence on the hydrophobic aggregation, suggesting that the formation of hydrophobic flocs is a promising means to recover smithsonite in the fine size range.

Sep 1, 2012

By G. Zaitsev

In mining and mineral processing, ammonium and nitrate from residues of explosives and other sources are discharged to the aquatic environment. Nitrogenous compounds in mine water can adversely affect the aquatic environment. The aim of this work was to study the biological removal of nitrate from cold inorganic mine water at the pilot-scale in an operating underground mine. Seven-months pilot testing on biological removal of nitrate from inorganic mine water was successfully performed in denitrifying fixed-bed biofilm reactors. The feed to denitrification bioreactors contained 11 mg NO3--N/L. Methanol was added as an external carbon source to the denitrifying bio-reactor since the inorganic mine water contained only traces of organic compounds (<CODCr (50 mgO2/L). Nitrate removal reached 75 g NO3--N/m3/d with removal efficiencies above 95% at temperature below 4°C. Thus, removal of explosives-residues from cold inorganic mine water was shown in pilot-scale biofilm reactors.

Jan 1, 2014

By M. Ito

The authors have developed the RETAC jig (a modified TACUB jig) and have reported that the RETAC jig can separate relatively low density particles such as plastics. To further improve the separation ability, a hybrid jig (a RETAC jig with an air bubbler under the particle bed), which can separate plastics having similar specific gravities by the differences in the wettabilities of the particles was developed. Surface modification of plastics with similar wettability enabling separation in the hybrid jig and the effects of wettability control of the plastics using reagents are reported.

Sep 1, 2012

By Zhazira Baltabekova, Nina Lokhova, Arailym Dukembayeva, Madali Naimanbayev, Zhantore Dzhurkanov

"Recycling of industrial waste provided they have enough valuable elements requires significantly less investment compared with ore processing. Promising man-made raw material of rare earth elements (REE) is phosphogypsum. Works performed on dismantlement of phosphogypsum only concern phosphogypsum processing from apatit. In this case, none of the developments was tested for phosphogypsum produced on the basis of phosphorus, chemical and mineralogical composition of which is markedly different from apatites. We studied phosphorites of the Karatau deposits (Kazakhstan). Mineralogically all the layers are composed of three main ingredients: phosphate, silica and carbonate, which account for 92-96% of the weight composition of ores and rocks. Of impurities there are pyrite, iron hydroxides, gypsum, fluorite. In addition to the actual composition of phosphate in phosphate ores there are apatite. Silica is presented by chalcedony and quartz, and carbonate by calcite and dolomite. The results of X-ray microanalysis showed point cluster of grains containing REE in samples of phosphate ore. Analysis of the grain showed that REE are in the form of phosphates and silicates, which according to numerous studies in apatites is not established. In this regard, phosphogypsum, waste of production, is different in composition too. Therefore, transfer of techniques proposed in the methods for extracting REE from phosphogypsum after processing apatite, did not give the stated results and required a new approach to solving this problem. It should be noted that the phosphogypsum produced by processing the Karatau phosphorite contains medium group of REE by 2.6, and heavy group by 7.8 times more than phosphogypsum from processing the Kola apatite. Given the shortage of medium and heavy REE research to develop ways to extract the lanthanides from phosphogypsum after processing phosphate rock is promising. The study contains results of studies on the extraction of REE from phosphogypsum after Karatau phosphorite processing."

Jan 1, 2014

By V. V. Morozov, Ganbaatar Zorigt, Delgerbat Lodoy, Y. P. Morozov

"At the processing plant Erdenet, a new facility for advanced ore diagnostics in-stream (at the conveyor), based on optical analyser of mineral composition, was tested. Such systems provide highly accurate in-stream measurements of ore properties. The system provided information on the ore mineralogical composition, the particle size distribution and the impregnation of minerals. A special flatbed facility for optical spectrum-based estimation of fine-crushed ore has been developed, being incorporated into the existing system of ore sampling and analysis. Application of the flatbed facility renders possible a high accuracy of determining ore mineralogical composition. High precision of the optical spectrum-based estimation is achieved using special devices, installed in the sampling and the sample analysis flow sheet, applied by the technical control department. Modern systems for optical spectrum-based estimation of ore grade provide a basis for effective automated control of ore benefication processes, based on the principle of advanced ore grade control. Process management task of grinding and flotation was to choose options that take into account the composition and grade of the ore coming. The calculation data array comprises consumption of reagents, ore processing, grind size etc. The systems implemented at the processing plant contributed to increasing copper and molybdenum recovery. INTRODUCTION In-stream ore grade analysis is a new trend in effective control of ore benefication processes. This is realised based on radiometric measurements in the X-ray and visible spectrum regions, in which mineral components of the initial ore (Sbárbaro and Villar, 2010) or the benefication products become apparent (Hyotyniemi and Ylinen, 1998; Haavisto and Hyötyniemi, 2010). An important advantage of such methods is in-stream measuring ore parameters, including mass fractions of individual minerals, which makes it possible to use the information obtained in the processes of automated control."

Jan 1, 2018

By B. P. Baruah

A good deposit of high sulphur coals of tertiary origin is existent in North eastern region of India. These coals are known to have indifferent characteristics in comparison to other Indian coals. The general Physico-chemical characteristics are low ash and high volatile matter, calorific value and sulphur content. Sulphur in these coals (70-95% of organic) is mostly affixed to the structure of the coal. Owing to the stringent environmental regulations, the utilization of these coals has severe limitations due to high sulphur content. In the present investigation, sulphur incorporation in to these coals has been discussed along with possible organic sulphur functionalities. The various desulphurization techniques carried out for removing sulphur from these coals have been discussed. Two step oxidative desulphurization processes has been found to be most efficient for organic sulphur removal along with mineral matter and potential toxic elements. Keywords: oxidative desulfurization, potential toxic elements, sulfur incorporation

Sep 1, 2012

By Henrique Kahn, Daniel Uliana, Carina Ulsen, Guilherme Nery

"Gold has been a material in high demand since the dawn of humanity. After hundreds of years of exploitation, the increasingly search for gold occurs in lower grade deposits with greater extraction difficulty. Therefore, for maximum efficiency, deep knowledge of the characteristics of these minerals and their associations is crucial, which is acquired through an accurate and rigorous routine of process mineralogy and batch extraction tests. The industrial gold process extraction occurs by gravity concentration, sulphides flotation and cyanidation. For gravity concentration, it is fundamental to establish the proportion of free or coarse gold grains and its association to heavy minerals; regarding flotation, the most relevant data are the proportion of gold associated to sulphides and their liberation by the surface area; for cyanidation, it is crucial to evaluate gold accessibility and the kinetics of leaching. Thus, the characterization of gold associations and liberation is vital to establish the plant design, to optimize operating plants and to reduce gold losses. Our aim is the characterization of gold occurrence in low-grade Brazilian deposits with complex mineralogical assemblages to support processing flowchart definition and to predict metallurgical recoveries. Gold distribution in light and heavy minerals was evaluated by heavy liquid separation and the occurrence of gold in free or locked particles was carried out on heavy products by SEM-based automated image analysis using the MLA system. All the products of heavy liquid separation were cyanidated in head samples with different milling conditions to evaluate the reaction kinetics and maximum recovery."

Jan 1, 2014

By Vladko Panayotov, Marinela Panayotova

"Recently, in order to extract metals, the industry is trying to process old metallurgical slag. The material requires very fine grinding that results in enhanced slime-formation. This in turn leads to problems in the course of the flotation process and to a loss of metal. In addition, it causes difficulties in the wastewater treatment aimed at water reuse. The aggregation and separation of the fine particles and their further subjecting to mineral processing would result in more efficient use of raw materials. Closing the water cycle also would be facilitated. The paper presents results from studying sixteen flocculation reagents, commercially available for treating municipal wastewater, including products based on nanotechnology, for their ability to rend the production wastewater in suitable for reuse in the flotation. It turned out that, from all studied reagents, the cationic C-587 is suitable for the purpose. Some of reagents were studied for their ability to flocculate selectively, in presence of coke fines, rich in copper fines which are produced at grinding of a slag from lead-zinc metallurgy. Most promising reagents are chosen, based on the chemical analysis of the flocculated materials. Open-cycle rough copper flotation experiments with the flocculated fines and recycled wastewater gave encouraging results."

Jan 1, 2014

By Gustav Hawlitschek, Henrique Kahn, Carina Ulsen, Renato Contessotto

"The problems related to waste dumping increased with the growth and development of large cities. In the U.K., more than 50% of landfill waste comes from construction use and the U.S. alone produces around 200 to 300 million tons of CDW annually. The exhaustion of natural sand deposits close to large urban centres stimulates the recycling of construction and demolition waste for the production of recycled aggregates as a construction material. This paper presents a flowchart for the production of recycled sand with low porosity and regular shape by the selective removal of the cement paste attached to recycled aggregates. The products characterization was carried out by the determination of the particle size and shape distribution, chemical and mineralogical composition, heavy liquid mineral separation and quantification of all present phases using a scanning electron microscopy with automated image analysis (SEM-MLA). The comminution of CDW by vertical shaft impact crusher made possible the production of a lower porosity recycled sand. The heavy liquid mineral separation showed that the proportion of low porous phases (d>2.5 g/cm3) is very high, exceeding 70% of the weight, encouraging further mineral processing separation to obtain a fine recycled aggregate with less cement paste content. The mineralogical characterization by XRD and SEM indicates that the main phases are tectosilicates, phyllosilicates and calcite which one can be attributed to both calcareous aggregate and cement paste. The precise quantification of cement paste and calcite/dolomite alone is just possible by automated image analysis. The characterization results demonstrated that proportion of phases with no cement paste attached increases progressively in denser products. The results of heavy liquid separations and image analysis are comparable and automated image analysis can be used for the characterization of phase content and their main associations."

Jan 1, 2014

By X. M. Wang

Magnetic floatation column (MFC) is a new equipment used for increasing content of iron, in which magnetite is separated in open gradient magnetic field. Simulation study was performed to investigate the separation characteristics of the separation method by analyzing the dynamic motion of magnetic particles. In this paper we compare two magnetic fields created by different magnets. The obtained simulation results give perspective in industrial design of MFC as the basis stage.

Jan 1, 2014

By Heinrich Hutchison, Thomas von Moltke, Roelof F. Sandenbergh, Katarina P. Cerovic

In the leaching of gold in aqueous cyanide solutions the rate of gold leaching may be decreased by the passivation of the gold, that may however be prevented or reversed in the presence of lead species in solution. In the present study potentiostatic, potentiodyanamic and XPS (X-ray photoelectron spectroscopy) analysis were used to further clarify the action of lead ions on the anodic activity of gold in alkaline cyanide solutions. It was found that lead increased the gold dissolution rate as it deposited on the gold surface at potentials more positive than its reversible Nernst potential for bulk metal deposition, i.e. by underpotential deposition mechanism, but that it decreased gold activity if present as bulk plated lead on the gold.

Jan 1, 2003

By A. Tolentino, J. Bravo, M. A. Corona-Arroyo, C. Quintero, R. Zarate, A. Lynch, L. Carillo

"This paper presents the performance of the flotation circuit of Minera Fresnillo PLC, Mexico. A plant survey was carried out on the lead banks and a size-by-size assay on the samples was conducted. The results indicate that the plant is treating fine particles in the flotation circuit. At least 30% of the particles in the feed are finer than 8 microns and that high amounts of Pb, Au, Ag and insolubles are in this particle size. It was also found that higher percentage of insolubles in the -8 micron particles are recovered in the final concentrate rather than being rejected in the tails. The presence of high amounts of insolubles in the concentrate is an issue of the company. The result of the plant survey provided valuable information for effective reduction of the insolubles in the concentrate and for plant optimization. The work conducted is part of the training of the students involved in a mine placement in the Alban Lynch Student Venture. INTRODUCTION Minera Fresnillo is one of the operating mines and the main contributor to the silver production of Fresnillo PLC group, the world’s leading producer of silver from ore. It is located in the mining district of Zacatecaz, Mexico, approximately 650 kilometers from Mexico City. The major minerals that make up the ore are galena, sphalerite, tetrahedrite, pyrargyrite, proustite, polybasite, pyrite and pyrrhotite. Minera Fresnillo has a capacity to treat 8300 tonnes of ore per day. The plant consists of semi-autogenous mill - ball mill – hydrocyclone circuit for primary grinding followed by silver-lead flotation then zinc flotation circuits. This paper reports the plant audit conducted in the silver-lead flotation circuit (Figure 1) of Minera Fresnillo. The circuit includes rougher, scavenger and two stages of cleaning. The tails from the scavenger goes to the zinc flotation circuit while the second cleaner yields the final silver-lead concentrate. The feed to the circuit has a particle size of 90% finer than 75 microns and generates a concentrate with grade of about 35% Pb, 5700 g/ton Ag, 16 g/ton Au and recoveries of 90% Pb, 90% Ag, 64% Au, respectively. Although the plant achieves their target concentrate grade and recovery, the concentrate also contains significant amount of insoluble materials which is about 18%. These insoluble materials consist of gangue minerals. The plant audit was conducted primarily to determine the possibility of further reducing the amount of insoluble materials present in the silver-lead concentrate."

Jan 1, 2018