Search Documents

By B. W. Zhao

Quantitative analysis of minerals composing in ore is primary in process mineralogy, a veracious quantification and analysis is very crucial to optimize or design a beneficiation process, especially for a low grade and complicated ore. This paper will discuss a SEM-EDS based quantitative analysis developed in JKtech Australia through an example from Jinchuan lean ore. For a low grade, com-plex intergrowths and texture lean ore, chemical phase analysis of value minerals and identification by optical microscope are very essential, unite the SEM-EDS based quantitative analysis, we can understand exactly the lean ore, explain and quantify the process performance.

Jan 1, 2014

By M. E. Holuszko

This paper reports the results of induction time measurements carried out on the products of film flotation of galena and sphalerite particles from three different size fractions (38~75µm; 75~150µm; 150~212µm). As expected, the tailings (sinking fraction) from film flotation at any particular surface tension, had always longer induction times than the concentrates (floating fraction), for both minerals. The difference between the induction times of film flotation concentrate and tailings could be as little as 2.5 ms and 5 ms, and as large as 6 ms and 10 ms. These differences can be related to the different hydrophobic characteristics of these fractions, as expressed by (?c) and composition of the particular film flotation product. In addition, the induction times of the larger particle size fraction were shown to be longer than for the corresponding smaller particle size fraction, even though the average ?c(degree of hydro-phobicity) of these fractions appears to be very similar. Desliming, Cu activation and collector addition to the sphalerite samples was shown to decrease the induction time values significantly.

Jan 1, 2014

By G. X. Du

Improving reaction effectiveness of asbestos tailings and acid is main means to increase the productivity of magnesium hydroxide and amorphous silica and to reduce production costs. In this paper, the process optimization of acid-leaching reaction process of asbestos tailings is reported. Through the orthogonal experiments of four influence factors, such as acid consumption, reaction temperature, reaction time and initial acid concentration in the leaching reaction. The experiment results indicated that the optimal process parameters were as follows: reaction temperature was 95?, reaction time was 1.5h, acid consumption was 218.9g hydrochloric acid(37%) per 100g asbestos tailings and initial acid concentration was about 25%. The influence significance sequence of the four factors was as follows: reaction temperature > reaction time > mass concentration of hydrochloric acid > hydrochloric acid consumption. Under the optimum process conditions, the leaching rate of MgO was 97.3%, total iron 98.15% and Al2O3 57.9%.

Jan 1, 2014

By Bharat Garg

The coking coal or clean coal from raw material division, Tata Steel Ltd. is a prime source of energy for inhouse steel making. Coal reserves of semi soft coking coal at West Bokaro is beneficiated by dense media cyclone and froth flotation processes to produce clean coal. In dense media cyclone process two byproducts-middling and rejects are also produced along with clean coal. With the growing demand for clean coal, it becomes imperative to maximize the recovery of clean coal in beneficiation processes. This will help, not only in reduction in cost of production, but also in raw resource conservation, and proper utilization. In this context, a case study was conducted at West Bokaro to identify opportunities for clean coal recovery from by-products. This paper mainly discusses the process for recovery of clean coal from byproducts and study of further liberation of clean coal from byproducts for economic consideration.

Sep 1, 2012

By Brian Loveday, Sandile Nkwanyana, Indresan Govender

"Recent batch experiments by the authors in a pilot scale ball mill (Ø = 0.6m) have demonstrated that a partial replacement of the ball charge by pebbles (25 % pebbles; 75 % steel balls) optimally reduces the ball and power consumption without altering the rate of production of fine material (passing 75 microns). At higher pebble volumes, the production rate of fines was reduced progressively. With the 25/75 composite charge a saving of 13 % in power consumption was achieved, and a saving of 25 % in steel ball consumption is implied. A partial replacement of steel balls by pebbles reduces the overall density of the grinding media in the charge. Taking into consideration that the production rate of fines is usually proportional to the bulk density of the charge in the mill, it would be expected that a composite charge (e.g. 25/75) would coarsen the grind and consequently reduce the rate of production of fines. Pebble wear contributes a small proportion of fines and it doesn’t provide a full explanation of why the 25/75 composite charge has no (or minimal) adverse effects on the rate of production of fines. Clearly, the production of fines across the mill is directly related to the shear and compressive power dissipation density. Accordingly, we hypothesise that the spatial power dissipation distribution meeting the minimum requirements for fines production— at the so-called active regions—are equivalent, or minimally comparable, for both the 25/75 composite and 100 % ball charge operating conditions. To test the hypothesis, we performed DEM simulations to analyse power dissipation in the active regions. 1. INTRODUCTION Comminution remains to be the most expensive process in mining operations, particularly because the energy consumed in this process accounts for 30-70 % of the total cost of a mining operation (Nadolski et al, 2014). Optimization of comminution circuits has been focussed on reducing capital and operating costs and maximising throughput capacity. For existing operations, it is often a challenge if the optimization process recommends retrofitting new ‘major’ equipment. The challenge arises from new capital cost and the difficulty of retrofitting in an existing circuit, while maintaining production (Major et al, 2001). Thus, for existing mining operations, optimization of comminution (cost and throughput) is often limited to operating conditions and/or addition of auxiliary equipment (such as pebble crushers, additional screens and high pressure grinding rolls (HPGR)) (McIvor and Greenwood, 1996; Hart et al, 2001; Powell et al, 2015b)."

Jan 1, 2018

By Y. C. Liu

Arsenic bearing copper-gold ores deposit have been found in most areas of China, especially in southwest. Due to the very closed association between arsenic, copper and gold, conventional flotation and cyanide leaching process may not give positive results. An arsenic bearing copper-gold ore in Sichuan province ,with gold grade of 10.12 g/t, 0.6% Cu and 0.14% As, is characterized by superfine grains with -40 microns fraction accounting for 70.9% and the gold enwrapped mainly by pyrite and tennanite accounts for 34.31%. Arsenic in this ore occurs in isomorphism, deposited in tetrahedrite. The ore was processed primarily in two stage flotation to get copper bearing gold concentrate and pyrite bearing gold concentrate respectively, and sequentially processed by leaching. Under the pressure of 300 KPa and 110~115 ?, the copper-gold concentrate was leached by an oxidizing and catalyzing leach agent then copper and gold were separated from each other in leach solution. The pyrite bearing gold concentrate was processed by cyanide leaching with the leach residue as sulfur product. The test results showed that copper recovery was up to 88.89%, gold recovery up to 89.18% and sulfur recovery up to 92.64%.

Jan 1, 2014

By Cheng Wei

Fly-ash was used as adsorbent to remove butyl xanthate from aqueous solution in this study. Adsorption kinetics investigation reveals that the adsorption process abides by the Lagergren-second-order Kinetic Model, and fine fly-ash prepared by grinding has a higher second-order adsorption rate as 1.25 g/mg?min and a higher saturated adsorption amount as 10.92mg/g. Four influencing factors as adsorption temperature, solution pH, consumption of fly-ash and adsorption time were investigated. Testing results indicate that butyl xanthate removal rates declines slightly with the temperature increase within the range of 15-50?, increases slightly when pH rises from 7.27 to 8.01 and then declines from 99.65% to 98.25% when pH rises from 8.01 to 11.10. An enhancement of removal rates can be observed by increasing the consumption of the adsorbing agent or prolonging the adsorption time. Thermal desorption was adopted to regenerate the used fly-ash, and test results show that fly-ash possess good regeneration performance and could be used as adsorbent repeatedly with little influence on the adsorption capacity.

Sep 1, 2012

By D. H. Xiong

Low grade oxidized iron ores are usually not economic to utilize. However, the development of SLon magnetic separators and other new technologies make the process cost lower and lower. In this paper, several low-grade oxidized iron ore process flowsheets are introduced. The key procedure is that at the early stage, SLon magnetic separators are applied to discharge as more tails as possible with very low cost, only a small portion of rough concentrate going to the cleaning stage, showing the new technologies are profitable for such iron ores.

Jan 1, 2014

By R. S. C. Smart

Surface chemical factors, including the balance of hydrophobic (e.g. collectors) and hydrophilic (e.g. oxidation products, precipitates) species, are major control determinants in flotation rates of specific minerals and therefore grade and recovery. There are a number of challenges involved with the surface analysis of different mineral phases from process streams in a flotation facility. The first is to collect samples that are representative of the process and retain their surface chemistry prior to introduction into the instrument. The second challenge in studying the surface chemistry of specific minerals is to find reliable methods of mineral phase recognition. In surface analysis of mineral particles, confident mineral selection can be difficult with many multi-metal minerals and with precipitated, adsorbed, reacted and contaminant species in the outermost molecular layers. The third challenge is to provide a statistical surface analysis of multiple grains of the same mineral. Methods to achieve these aims are described. Principal component analysis (PCA) of ToF-SIMS data provides improvement in phase recognition, particle selection and associated variations in surface species. Specific examples from both lab and plant operations, demonstrate that this technique can be utilized to differentiate surface chemical factors promoting (hydrophobic species) or inhibiting (hydrophilic species) flotation. A study of copper ion transfer (inadvertent activation) from chalcopyrite to pyrite and sphalerite clearly identified a statistical difference in copper intensities between the sphalerite and pyrite phases corresponding to their flotation response. The PCA analysis applied to concentrate and tails samples collected from the Inco Matte Concentrator demonstrated extensive CuOH and NiOH transfer between chalcocite and heazlewoodite minerals. The statistical analysis has been able to identify mechanisms controlling recovery and selectivity. High intensity conditioning (HIC) tests in which sphalerite was separated from a complex sulfide ore gave a 5% increase in the overall Zn recovery. The PCA/ToF-SIMS statistical analysis revealed the discriminating depressant action of adherent aluminosilicate (gangue) fine particles and adsorbed ions on the surface of sphalerite grains. HIC conditioning resulted in the removal of these gangue fines improving surface collector attachment efficiency.

Jan 1, 2014

By B. McFadzean, P. E. Ngoepe, P. P. Mkhonto

"The theoretical technique of computational modeling and the experimental determination of the enthalpy of adsorption of a ligand molecule onto a mineral surface deliver the same output parameters and, therefore, complement each other in investigating the affinity of different ligand types for mineral surfaces.This study ran parallel experimental tests and computational calculations to determine the enthalpy of adsorption of a series of increasing chain length xanthates onto a pyrite surface. The outcomes showed that, while the absolute energy values were different, the trends were similar. Both computational and experimental approaches showed that the extent of the interaction of the xanthate molecule increases with increasing carbon chain length. The computational values were larger than the experimental values, which could be explained, in part, by the addition of water to the computational system, which resulted in a decrease in the heat of adsorption on the (100) surface, compared to the adsorption of the collector in a vacuum. The computational method showed that, in the case of the pyrite (100) surface, the most exothermic reaction was obtained when the two xanthate sulfur atoms bridged two pyrite 5-coordinated iron atoms. The (111) surface was found to be more reactive and different adsorption mechanisms were predicted for each of the C2, C3, C4 and C5 chain length xanthates.The experimentally determined exothermic increase in heat of adsorption for the addition of each CH2 group was found to be -8.17 kJ/mol. The contribution of the thiol head group was -34.9 kJ/mol. Previous studies on self-assembled monolayers have shown that these values are compatible with lateral interactions between CH2 groups and the exclusion of water. This study provides a rigorous experimental and computational approach which is intended to afford confidence in modelled data for the screening of new ligands for flotation processes.INTRODUCTIONComputational modelling is a fast and cost-effective method of screening collector molecules for the efficacy of their adsorption onto mineral surfaces. However, it is desirable to measure the computational outputs against experimental outputs to check for congruency. Computational modelling and experimental microcalorimetry both deliver the same output parameter: the energy of adsorption of the molecule onto the solid surface. These techniques are therefore ideally suited to complement one another in investigating the affinity of the interaction between collector molecules and mineral surfaces."

Jan 1, 2018

By G. Venkateswara Rao

The jigging of ferrous ore to produce higher-grade products has been practiced for many decades. This is due to easy separation, a beneficial trade- off between operating cost and reduced yield relative to Dense Media Separation (DMS). Jigging becomes prominent for beneficiation of iron ores in the coarser size range. At present drive is towards the use of under bed air pulsed jigs for the beneficiation of ferrous ores. The main advantage is that the under bed air pulsed jigs are capable of generating the large pulse of amplitudes required to fluidize a deep bed of heavy ores particularly lump iron ore up to 40mm size. The major jig parameters effecting the jigging operation are bed height, shape of the pulse, residence time, operating pressure, valve cycle time and water flow rate. With the pulse shape set correctly for optimum stratification rate, even it is still necessary to provide enough residence time, to ensure the difficult material will take time to migrate to the expected layer in the bed. In order to find the Jig Stratification Index (JIS) parameters like bed height, operating pressure, water flow rate, cycle valve time and shape of the pulse were optimized first by conducting various tests. Typical Iron ore samples from Odisha (both lump and fines) were subjected to stratification studies at residence time of 1, 5 and 15 minutes. Jig Stratification Index (JSI) for both lump (0.30) and fines (0.20) were determined by using APIC Jig. The maximum possible JSI was calculated by using heavy liquid separation test (0.42 for lump and 0.24 for fines). It is found that the jig bed JSI is less than the Heavy liquid JSI for both lump and fines. The ratio of Jig bed JSI to the heavy liquid JSI is 0.83 for lump and 0.71 for fines. The JSI and ratio of Jig bed JSI to Heavy liquid JSI are low for fines due to fluid turbulences causing some degree of remixing in the jig bed. The fluid turbulences are more for fines than lump, hence jigging of fines is difficult and challenging. Keywords: sub grade iron ore, gravity separation, jigging, apic jig, stratification, residence time, jig stratification index

Sep 1, 2012

Froth flotation is an industrial process commonly used for the separation of mineral particles. Bubbles sparged in a pulp collect and carry hydrophobic particles to the top layer of a flotation cell, the froth zone. There is a strong correlation between the stability of the froth phase and the flux of solids. However, flotation units placed in series operate, as a whole, in a non-steady state regime with the concentration of particle decreasing from one cell to the next resulting in a decrease in froth stability, which can compromise the recovery of valuables. Organic chemical reagents, frothers, are generally added to prevent fine bubbles from coalescing and to increase the stability of the froth phase. Frothers represent the second largest group of mining chemicals. It is crucial to understand the resulting properties of the frother on the froth phase in order to select the most suitable reagent for a particular operation. The bubble coalescence dynamic of three different surfactants, 1-pentanol, poly (propylene glycol), and tri (propylene glycol) methyl ether, were investigated in this study. In the first stage, the stabilisation mechanism of bubbles in a solution of surfactant was investigated using a specifically designed experimental setup. The coalescence behaviour of bubble pairs was recorded using high-speed video imaging in which information such as the coalescence time and the deformation of the resultant bubble upon coalescence could be extracted. The results were then compared between the different surfactants for several concentrations. It is shown in a study that the coalescence time increases with surfactant concentration until the Gibbs-Marangoni effect is suppressed by bulk diffusion. Conversely, the oscillation of the resultant bubble was found to be affected only at concentrations at which the film is saturated. The implications of the effects of surfactant type and concentration on the coalescence time and bubble oscillation in froth flotation are discussed. Keywords: froth flotation, frother, bubble coalescence

Sep 1, 2012

By V. I. Ryaboy, V. P. Kretov, S. E. Levkovets, I. V. Ryaboy

"Using the flotation of a gold-containing ore from a deposit in Kazakhstan as an example, we have conducted a study designing dialkyldithiophosphate collectors, in addition to xanthates, for the flotation of hard-toenrich gold-containing ores to increase gold recovery.The increased flotational ability of the dialkyldithiophosphates was determined by their surface activity at the liquid-gas interface and their hydrophobic ability, the changing of which allowed us to control the collecting power and selective ability of the dialkyldithiophosphates. The studying of the surface activity of aqueous solutions was done using the stalagmometric method and the evaluation of the hydrophobic ability was done in percentage of the relative value of the zinc ion binding in the solution in standard conditions.Studying the influence of surface activity in our designed dialkyldithiophosphate collectors, with their close hydrophobic ability, showed that even with a small increase in surface activity in their aqueous solutions, gold recovery increased by 2-3% in laboratory conditions. Using this enabled us first to apply the dialkyldithiophosphate collector BTF-161 at a plant in Kazakhstan, and then to introduce the specially designed dialkyldithiophosphate collector BTF-163, which has been in use since. Further study of dialkyldithiophosphate activity based on this concept showed us that for the range of short-chain dialkyldithiophosphate collectors with a chain length of up to ?5, the effectiveness of ore processing became lower the higher their surface activity got, with relatively small differences in their hydrophobic ability. For long-chain dialkyldithiophosphates with a chain length of over ?5, ore processing effectiveness increased with the increase of their hydrophobic ability.Based on these studies, a new effective dialkyldithiophosphate collector, BTF-1517, was designed. Using this reagent in continuous gold recovery tests allowed us to reach an 84.21% recovery with a concentrate quality of 15.66 g/t, while using the applied collector BTF-163 in similar conditions led to the recovery of 82.87% with a concentrate quality of 15.65%. As a result, the Kazakhstan processing plant decided to conduct industrial tests with the BTF-1517 collector."

Jan 1, 2018

Hydrofluoric acid (HF) is traditionally used in plant operation to separate feldspars from quartz. It acts during the conditioning step as a pH regulator and an activating agent providing an excellent selectivity. However, a corrosive chemical environment and the ecological impacts from the potential fluoride ion contamination are limiting factors to use this chemical agent at an industrial scale. Investigations of the amine-feldspar interactions in the absence and presence of non-linear long-chain alcohols were carried out on two ore samples. The presence of alcohol molecules led to form a closed packed layer only on the surface of feldspars. The highest order and packing at the feldspar surface were observed with a particular alkyl chain structure as Guerbert alcohols. A new flotation process was developed and tested at both lab and pilot scales on different feldspar ores. The Guerbert alcohols allow to perform a feldspar concentrate with very low content in quartz (2.3-3.5 %) and feldspars recovery from 78 to 81 % while the aliphatic isoalcohols show a more higher recovery level (88-89 %). New HF-free process is strongly dependent on the pH range (1.7-2.5) and sulphuric acid consumption during conditioning steps. Optimal amine/alcohol weight ratio is ranged between 0.8 and 1.0. The values below 0.8 decrease strongly the flotation selectivity and the quartz recovery within the feldspar concentrates is higher than that occurs with HF.

Sep 1, 2012

By T. V. Chnyrenkova, J. Troncoso, V. A. Luganov, G. P. Kluev

"Arsenic-gold bearing ores are used as flux in smelting or are leached to extract gold. The main aim is to decrease the arsenic content in processed materials and to break up the ore lattice, thus liberating the gold. Some regulations were established by authorities for sulfidizing of arsenic bearing compounds in a presence of pyrite and for oxidation of ores and concentrates in the presence of soda.This article analyses the results of laboratory and pilot plant testing of dissociating and oxidizing roasting of gold-arsenic bearing concentrates. During the dissociation roasting under vacuum, arsenic is sublimated into elemental and sulfide forms. This process allows for the minimization of the negative influence on the environment, but requires costly engineering solutions. Roasting in a limited quantity of oxygen in the gaseous phase makes it possible to sublimate arsenic in the form of oxides and sulfides and it may be carried out in fluid bed furnaces.Oxidizing roasting of the concentrates in the presence of soda results in formation of water-soluble compounds and forces practically all arsenic and sulfur to remain in the cinder."

Jan 1, 2003

By Z. H. Zhang

Shizhuyuan is a world-class WO3, Mo, Bi and CaF2 poly-metallic deposit; it has rich reservation, but great difficulty in ore?s processing; thereby, for many years, it has been the target problem of beneficiation technologies. This paper, while briefly reviews its main scientific and technological advancement, pays special attention to the complete set of new technology and technical index achieved in recent years, which is characterized by using full-floatation flow-sheet as the backbone flow-sheet, explores some key factors influencing tungsten floatation, and presents a brief introduction to such new equipment as flotation column and comprehensive utilization of fluorite.

Jan 1, 2014

By Chuansheng Luo

If lead-zinc ores have high oxidation rate, separation of lead and zinc is very difficult. This paper studied the technology of preferential flotation by the coarse grinding and re-grinding. The lead concentrate grade is 51.40% and the lead recovery is 62.83% when feed grades Pb 1.74% and Zn 6.46% with oxidation rate being 13.75%. At same time, the zinc concentrate grade is 50.07% and its recovery is 90.01%.

Sep 1, 2012

By Sanchita Chakravarty, Sumantra Bhattacharya, Divya Jyoti, A. K. Mukherjee, Soni Jaiswal

"Release analysis is independent of collector and frother dosage and type, but it is primarily influenced by the degree of liberation or “state of release of the sample”. The shape of release curve is an indication of the degree of liberation. This paper briefs about the effect of reagent combination, particle size and surface characteristics on the release analysis of difficult-to-clean LVC coal.Release analysis of three LVC coal fines obtained from two different coalfields of India was carried out at three different size levels such as -0.5mm, (-0.5+0.1) mm, and -0.1mm. The collectors used were n-dodecane and commercial diesel oil. Incomplete liberation of coal fines even at a size of -100µm, corroborated by photomicrographs of ROM and clean coal macerals, in a great measure reduced the flotation-based cleaning potential of the fines. FESEM images of fines reveals that the adherence of ultrafine onto the surface of relatively coarser particles reduced the clean coal recovery. The results obtained also appear to be coal, reagent combination and, particle size and particle surface specific. Only one coal indicated the liberation as is usually expected for -0.1mm particles with a reasonable yield of 65% at 18% ash. INTRODUCTION Froth flotation has a long history of being used to treat coal fines. Coal flotation is considered to be difficult, if the percentage of Near Gravity Material (NGM), i.e. essentially locked particles, in flotation feed is >10% [Aplan, 1993], which is usually the case with all the coking coal fines in India. The fines are rich in vitrinite, so valuable for coking coal. Unfortunately, there appears to be no standard procedures to determine the separation efficiency of froth floatation. Release analysis proposed by C.C. Dell in 1953 [Dell, 1953], aimed to determine the ultimate floatability of coal. Several other techniques had been proposed but release analysis technique has been considered to be a vast improvement over the batch flotation process [Forrest et al. 1994]."

Jan 1, 2018

By Matthew Thurley

Optimisation and control of comminution, pelletization, and agglomeration processes is a complex task with large potential for gains in productivity, energy efficiency, and particle size distribution quality. One factor in realising these gains is the requirement for fully-automated online particle size distribution measurement. Moreover, online particle size distribution measurement that is based on the particles on the visible surface and can avoid or mitigate substantial errors that result from under-sizing overlapped particles and over-sizing areas of fines particles. Literature review indicates a body of substantially 2D photographic based particle size measurement systems that suffer from a large number of significant errors except in the simplest case of a monolayer of particles under good illumination with limited color variation in the material. In order to measure the visible particles on a pile there are a number of requirements including; avoiding particle delineation errors due to variation in material color and shadows, detect overlapping versus non-overlapping particles, and identify areas of fine particles as fines and not large rocks. Results are presented using a fully-automated online measurement system of crushed rock on conveyor belt using a 3D surface laser profile. The system provides continuous online measurement and results are shown on over four hours of production after the primary crusher. Size distribution results are calculated using volumetric estimation of the particles on the surface of the pile. The results show a strong capability to discriminate size variation especially in the 10% and 20% passing values. Furthermore results show that if areas of fines are misclassified as large rocks, and overlapped particles misclassified as small rocks, then a near complete loss of discrimination occurs for the P10 and P20 values which become largely constant values.

Jan 1, 2014

By B. McFadzean, P. E. Ngoepe, P. P. Mkhonto, J. Taguta

The adsorption of heterocyclic collectors such 2-mercaptobenzothiazole (MBT), 2-mercaptobenzoxazole (MBO), 2-mercaptobenzimidazole (MBI) and their derivatives on pyrite form a basis in understanding the flotation reactivity that may be applicable in a wide range of sulphide minerals. This study uses a computational and experimental approach to determine the heat of adsorption of MBT, MBO, MBI and modified MBT collectors onto pyrite surfaces. Computational calculations found that the adsorption energies were in the order: MBO > MBI > MBT. The heterocyclic collectors were adsorbed in their thiolate form on the surface. In the case of the pyrite (100) surface, the MBT adsorbed through the exocyclic sulphur atom, while MBO and MBI adsorbed through the exocyclic sulphur and N atoms onto the 5-coordinated Fe atom. The (111) surface was found to be more reactive and different adsorption mechanisms were predicted, where the MBT exocyclic sulphur atom bridged on the 5- coordinated Fe and surface 2-coordinated sulphur atoms, while the N atom adsorbed on the 5-coordinated Fe atom. In the case of MBO and MBI, dissociation of the exocyclic sulphur atom from the collector occurred with subsequent interaction with the surface 5-cordinated Fe and 2-coordinated S atoms. This resulted in the collector carbon atom adsorbing on the surface 2-coordinated S atom, while the N atom adsorbed on the 5-coordinated Fe atom. The adsorption of the modified MBT was found to be more exothermic than the MBT, which showed that introduction of a –CS2 group on the exocyclic sulphur atom improved the affinity of MBT on the surface, and was thus a better flotation collector. The computational results were supported by experimental enthalpy of adsorption measurements and microflotation tests. The chemistry of the heterocyclic thioamides is complicated by the fact that they can exist in a number of tautomeric and ionic forms at different pH’s. This is discussed in relation to the flotation and calorimetric data.

Jan 1, 2018