Search Documents

By L. Gao, X. Gui

Fine coal obtained from Kailuan mine served as the processing object of this study. This material was difficult to separate. A flotation rate experiment was designed to investigate the process distribution characteristics of size and density during fine coal flotation. Size and density analyses of five clean were studied. The mineral morphology of flotation rate experiment cleaning was observed through scanning electron microscopy. The fractions -0.074+0.045 mm and -0.045 mm exhibited the best practical floatability and presented the highest combustible body recovery rates, but the selectivity and natural floatability of these two fractions were the worst. The - 0.074 mm fraction has contaminated the clean coal from the early stage of flotation, and the cumulative clean coal ash of -0.074 mm reached up to 17.20%. The low and middle-density classes displayed varying flotation behavior, but the flotation yield difference was only nearly 3%. The middle-density class caused the clean coal to have high ash content. The poor selectivity of fine coals, middle-density fraction, and fine mud resulted in high-ash clean coals during flotation. Thus, improving the selectivity of fine coal, restraining the flotation of fine mud, and grinding the coal to decrease the middle density mass fraction to liberate clean coals can yield high-quality clean coals through flotation.

Jan 1, 2014

By D. Moradkhani

Copper metal has important role in the basic industrials, as if it did not exist, modern human life would not develop! Copper leaching, as the first step, is important step in copper production processes. In this research, efficient factors on the leaching have been investigated. For this reason, four efficient factors on leaching namely pH, liquid to solid ratio (L/S), temperature and time, as independent variables, were optimized using response surface (RSM) with D-optimal. A quadratic equation was used to create response and contours. According to the results from analysis of variance (ANOVA), the value of determination coefficient (R2=96.77%) indicates that the model was good fit. Optimum experiment condition also was found: pH of 1, L/S of 8.24, temperature of 26.06 ? and time of 43.64 min. At this condition, the maximum recovery of copper was equaled to 92/38 in which good desirability achieved.

Sep 1, 2012

By Lilong Huang, Xiang Zhao, Yuan Long, Li Shi, Guowang Zhang, Xiao Xiao

"Vertical stirred mill is expected to upgrade the iron concentrate by further size reduced efficiently. The tests for fine grinding of iron ores from Baiyun Boyu iron ore, Baogang Goup, iron contained tails of Cu-Pb-Zn ore in Wanguo ore, Xiaoshalong iron ore in Qinghai were conducted in this paper. The data of appropriate grinding fineness, optimum grinding conditions and energy consumptions obtained from the test were used to select appropriate scale of the vertical stirred mill, optimize the parameters of the grinding process and upgrade the iron concentrate of the iron ore dressing plant or design the new ore dressing plant. Based on the laboratory tests, industrial system of regrinding and magnetic separation with vertical stirred mill as the regrinding mill in micro-fine grained iron concentrate upgrading has worked out very well. The grade of Fe in iron concentrates has increased to about 65.0% (by 4.0~6.5 point percent) when the iron concentrates were reground to designed fineness and the specific energy is 5.0~7.1kWh/t. The system of regrinding and magnetic separation is proven to be eco-efficient in iron concentrate upgrading."

Jan 1, 2014

By U. S. Chattopadhyay

The estimated requirement of the nation by the year 2020 is approx. 80 Mt of steel and more than 0.2 million MW installed capacity of the electricity, thereby increasing the consumption of the coking and non-coking coal, which is expected to be in tune of about 75 Mt & 500 Mt respectively. One of the major deleterious factors in achieving the goal is the deteriorating quality of the feed coal used in both steel and power industries. Indian coking coals, in general, are typified by high ash, high inert (both organic and inorganic), low rank, low reactive macerals content, heterogeneous petrographic make-up, inferior coking properties and poor amenability to washing, thereby necessitating suitable washing measure. Coke-based steel industries in India require washed coking coal containing ash % varying between 17-19. The situation demands taking on immediate challenges to fill up the gap between the requirements and supply of coking coal. This paper reviews the R&D attempts in this laboratory and throws light on the key measures as long-term solution to the problem. Search for alternative source of coking coal, like LVC coal and their judicious preparation technology. The low volatile coking coal (LVCC) constitutes about 50% of the total coking coal reserves in India. These coals are characterized by high raw coal ash content (37 to 40%) and very difficult washability potential. If these coals are treated in the existing washeries, which are generally 2 or 3-product systems, the cost of clean coal is high as the byproduct sale value is low. It has been proposed to produce a new type of by product, which enjoys high demand and good coking properties.

Sep 1, 2012

By A. K. Mukherjee

In this apparatus closed sized particles are placed in a container and then fluidized by passing water through the load of particles. Water flow is adjusted to deposit particles in one or more layers depending on the specific gravity of each of the particles, after which the deposited particles are separated in portions of different specific gravity. The obtained portions represent different ore content of the closed sized fraction. The process is repeated for all other size fractions to generate washability curve of the feed. Three different types of iron ores and one coal sample are tested in this equipment. The theoretical yield-grade curve generated for iron ore feed is unique in absence of any such practice for ore minerals. Similar curve is generated for coal and it is compared with washability curve, an existing practice followed worldwide. This comparison validates the performance of the process and the equipment.

Sep 1, 2012

By Jingzhong Kuang, Zheyu Huang, Chuanzhou Guo, Pengfei Liu

"In this paper, scheelite and scheelite coated with Pb2+ (SC) were synthesized by chemical precipitation with the help of ultrasonic. The role of the Pb2+ on scheelite was evaluated. Additionally, the dissolution behavior of minerals and the adsorption mechanism of collectors were investigated systematically via SEM, XRD, EDS. The results indicate that the ultrasonic cavitation can promote the formation of scheelite with large particle size and high crystallinity. Due to the exchange of WO4 2- and OH-, the dissolution of scheelite are not in a 1:1 equivalent amount by chemical formula and the concentration of WO4 2- is higher than that of Ca2+ in the solution because Pb2+ promotes the transfer of WO4 2- from scheelite surface into the solution. The dissolution of scheelite is an endothermic reaction and its enthalpy reaches the maximum value of 692.59J·mol-1 at pH=8~10. But the coating of Pb2+ changes the thermal effect of scheelite in the solution and the dissolution of SC is an exothermic reaction with the dissolution enthalpy of -262.30 J·mol-1. At pH=8~10, the adsorption capacity of sodium oleate and salicylhydroxamic acid on the surface of SC is higher than that of scheelite which delivers that Pb2+ contributes to the scheelite surface dissolution and enhances the adsorption of collectors on the mineral surface, thus achieving activation.INTRODUCTIONIn modern society, tungsten is a type of quite important rare metal and also a strategic resource. Because of its low vapor pressure, high melting point, good electrical and thermal conductivity properties, it is widely applied in high-temperature technology, lighting, machine and engine construction (Zhao,Z.W, 2013; Yan, W, 2017; Ilhan, S, 2013). Both scheelite and wolframite are the major tungsten deposits. With the depletion of easily-processed wolframite, scheelite has drawn a great deal of scientific and industrial attention. Scheelite can be recovered by flotation due to the metathesis of polarity and chargeability on minerals surface via adding regulators and collectors."

Jan 1, 2018

By G. Unland

The sizing of crushers depends on the expected crushing forces. However, the crushing forces develop differently with every individual rock while it is compressed by the working surfaces of the crusher. For sizing, this compression process has to be characterized by the maximum crushing force. The maximum crushing force depends on the strength, shape and size of the rock, the amount and velocity of the imposed displacement of the working surfaces of the crusher on the rock and the conditions of the contact surfaces. From experience it is known that the strength of the material and, therefore, the crushing forces depend on the size of the specimen. This dependence is the so called size effect. The determination is based on compression tests. The force development is recorded during the compression of the specimen and for every individual test the maximum force is determined. The occurring maximum crushing forces of several rocks with the same diameter comminuted under the same conditions can be assessed by a mean value and a variance. The relationship between the mean values of the cross section related maximum crushing forces FAmax and the corresponding sizes d of the specimens can then be described by mathematical functions. They are derived from different approaches (phenomenological, statistical and statistical-physical methods). The phenomenological methods are subjective and yield functions depending on the assumptions of a person, whereas the statistical and statistical-physical methods are based on an evaluated function and the optimization of the parameters.

Jan 1, 2014

By I. Yochev, A. A. Metelev, A. I. Stepanenko, A. P. Purgin, M. G. Viduetsky, A. M. Panshin, I. F. Garifulin

"Pneumatic flotation cells of the KFM series are intended for the concentration of various ores and technogenic materials. The key operating principle of the flotation cells of the KFM series is the preparation of pulp for flotation in blowers, offering the advantage of an accelerated flotation process. This report summarizes the results of the implementation and operation of the KFM cells at Russian and foreign projects in 2015-2017. Their implementation and operation experience confirms the high efficiency of the KFM cells, especially in the head of lead and zinc, copper and zinc, copper flotation processes:head KFM-600 flotation cell recovers from lead-zinc ore (Rudmetal AD modular concentrator) up to 52% of lead in a single stage (without cleaner flotation) in a salable lead head concentrate (grade of up to 76% lead, 2.3% zinc). The flotation cell proved to be much more efficient than originally expected in the process description in the design phase,flotation of the copper-zinc ore from Novo-Shemur deposit (PJSC Svyatogor concentrator) in two KFM- 1400M cells recovers up to 65% of copper and 70% of zinc in a high-grade bulk copper-zinc concentrate containing 12-13% of copper and 25-28% of zinc. The installation of the two cells with a combined capacity of 26 m3 allowed to decommission 4 chambers of FPM-16 pneumomechanical flotation cells with a combined capacity of 64 m3 with a simultaneous increase in the overall ore concentration performancea single KFM-1400M cell (13 m3) recovers from the copper ore from Volkov deposit (PJSC Svyatogor concentrator) 53% of copper into a high-grade copper head concentrate (33.0% of copper). For comparison, the pneumomechanical cell FPM-16 (capacity 16 m3) has almost half as low copper recovery (29.6%) into the head concentrate at a lower grade (30.5% copper)."

Jan 1, 2018

By Pat Turner, Abrie Schutte, Tim Olson, Roman van Ommen

The key to good cyclone circuit design and operation in primary grinding circuits will be discussed. Cyclone circuit design issues include individual cyclone design features such as cone angle or materials of construction, as well as orientation and manifold configuration. Cyclone performance issues as well as maintenance considerations will be detailed in an effort to achieve consistent cyclone operation with minimal coarse solids in the overflow. The new gMAXTM. cyclones will be introduced and evaluated using operating circuit data in closed circuit grinding applications

Jan 1, 2003

By Paul W. Weiblen, Louis J. Cabri, Rolando Lastra

"Preliminary tests were done to determine whether comminution by electric-pulse disaggregation, or E-PD (cf. Rudashevsky et al; 1995), was more effective than using conventional crushing for Merensky Reef ore. A hand sample of the Merensky Reef was sawn in two: then one sub-sample was comminuted to .2 mm using E-PD at the University of Minnesota, and the other sub-sample was crushed to .2 mm using a conventional jaw crusher at CANMET.The products of the electric-pulse disaggregation and jaw crusher were fractionated by sieving and by a separation using a heavy liquid with a specific gravity of 3.3, because the proportion of platinum-group minerals (PGM) and sulphides to silicate minerals is very low. Thus, four mineral separates were produced: .2000 + 833 µm, -833 +208 µm, -208-µm float and -208-µm sink. All the mineral separates were studied by image analysis (Lastra et al; 1998). The main objective was to determine the liberation of gangue (silicate minerals), chromite, pyrrhotite, chalcopyrite, pentlandite and PGM. In the case of the PGM, a specific image analysis program was written to search and measure these minerals.The results show that the liberation obtained for gangue was similar (~99%) using either method of comminution. However, the liberation obtained for chromite (~89% vs. ~38%), pentlandite (~50% vs. 1%), pyrrhotite (~56% vs. ~38%), and PGM (~56% vs. ~1%) by E-PD was higher than that obtained by conventional jaw crusher, whereas the liberation obtained for chalcopyrite (~20% vs. ~71%) by E-PD was lower. Nevertheless, the image analysis of the products also showed that the PGM are strongly associated with pentlandite. Thus, for the Merensky Reef, liberation of pentlandite from the gangue minerals and chromite is important to recover more of the PGM. This maybe be significant because, in addition to increased recovery of platinum-group minerals (PGM), Merensky Reef pentlandite also contains significant quantities of valuable platinum-group elements like Pd and Rh (Cabri, 1981; Cabri 1988, Kinloch 1982, Peyerl 1983). Hence, the results indicate that for the Merensky Reef, electric-pulse disaggregation would represent a better comminution operation than a conventional jaw crusher would. In addition, the greatly improved liberation for chromite may find application for the PGM-rich UG2 chromitite."

Jan 1, 2003

By P. Spolaore

In the frame of Bioshale FP6 project, the bioprocessing of a polymetallic and polymineral concentrate produced in an industrial operation in Lubin, Poland, was assessed. Following successful batch culture tests, processing in continuous conditions was tested to determine the main specifications for the application of the stirred-tank technology to this sulphide concentrate from black shale ores. The experimental work was carried out in a laboratory-scale unit consisting of 3 stirred tanks (50L or 20L) using an acidophilic and moderate thermophilic bacterial population. Different configurations of the unit and key operating parameters were tested (nutrient medium composition, solids concentration, rates of agitation and aeration). Scientific and technical approaches, such as bacterial community structure and mineralogical analysis were implemented in order to better understand the chemical and biochemical reactions occurring in the system. Using the data produced during the continuous operation, downstream processing assessment for both copper and silver recovery was also carried out. The best copper recovery obtained in the continuous operation was 92% and a hot brine leaching of the bioleach residue (PLINT process) allowed to recover 92% of the silver. A preliminary tech-no-economic evaluation of Lubin concentrate bioprocessing including bioleaching, copper and silver recoveries demonstrated the potential economic feasibility. Recovery of silver plays an important role in the economy of the process. This study presents promising values to further investigate this bioprocessing option.

Jan 1, 2014

The major components of sylvinite ores, sylvite (KCl) and halite (NaCl), are separated by flotation. Since both these minerals are water-soluble, the process is carried out in a saturated brine, 6~7 mol/L aqueous solution of NaCl and KCl. C16~C22 primary amines, utilized as a collector, are practically insoluble in water. In commercial potash ore flotation operations these amines are melted by heating up to 70~90°C. They are then neutralized with hydrochloric or acetic acids, and such a hot emulsion/dispersion is introduced to the flotation pulp (which is at room temperature). This is immediately accompanied by the appearance of a white precipitate in the system. As our measurements indicate, the Krafft point of dodecylammonium chloride in concentrated electrolyte solutions is much higher than 80°C, and the Krafft point of C16~C22 amines is substantially higher than that. Introduction of a hot amine emulsion into a pulp, at temperature much lower than the Krafft point for the utilized amines, must cause precipitation of the amines. Some of these species are obviously flotation-active. It is interesting to observe that in summertime, when temperatures are high-er, longer chain amines perform better. It demonstrates that the colloidal amine species that precipitate serve as active species in the potash flotation. Therefore, at higher pulp temperatures, when the temperature difference between the pulp temperature and the Krafft temperature of the utilized amine is not sufficiently large, a longer chain amine, the amine with a higher Krafft point, is more efficient. The results reveal that premixing of an alcohol such as MIBC (common frother) with the amine significantly improves flotation performance of the amine. In the presence of such an alcohol the amine disperse system becomes less turbid, and the rheology of the system less non-Newtonian. All this indicates that MIBC, which does not operate as a frother in a potash flotation system, when used as a co-surfactant, enhances the dispersion of the amine colloidal system. The appearing colloidal species perform as an active form of the collector.

Jan 1, 2014

By Yuemin Zhao

Pre-combustion cleaning of coal plays a key role in the process of efficient and clean utilization of coal resources. Recently, wet beneficiation of coal is predominant around the world. Nevertheless, wet beneficiation processes are limited by the increasingly serious problem of worldwide shortage of water, especially in China. Thus, it is imperative to develop efficient dry coal beneficiation techniques. Currently, several technologies such as air dense medium fluidized bed, compound dry cleaning and air jigging have successfully achieved high-efficiency separation of 50~6 mm coal. However, in recent years, a large amount of fine coal is generated as the mechanized mining technology has been progressively deployed in coal sector. Thus, it is necessary to develop efficient dry beneficiation techniques for fine coal. In recent years, many countries including China, India, Canada, Germen, and Australia have carried out many research works on fine coal dry beneficiation techniques. China University of Mining and Technology has carried out systematic researches on the introduction the vibrated energy to traditional air dense medium fluidized bed for fine coal beneficiation. This paper studied air dense medium vibrated fluidized beds (ADMVFB) for fine coal dry beneficiation. The experimental results show that the coal of <6 mm size can be beneficiated in an ADMVFB efficiently with the E value of 0.065~0.085, the separating density can be adjusted in the range of 1.45~2.2 g/cm3, and the lower limit of beneficiation can reach to 0.5 mm. Keywords: fine coal, air dense medium vibrated fluidized bed, coal separation, dry separation

Sep 1, 2012

By Ruiyang Zhang, Ping Fang, Dezhou Wei, Shuling Gao

A CFD based numerical simulation of flow characteristics of hydrocyclone was conducted with different structural and operational parameters to investigate its distribution characteristics and influencing mechanism. The results show there exist several unsymmetrical envelopes of equal vertical velocities among both upward inner flows and downward outer flows in the hydrocyclone, and cone angle and apex diameter have remarkable influence on the vertical location of the cone bottom of the envelop of zero vertical velocity. It is also found that some tangential velocity isolines exist in the horizontal planes located in the effective separation region of hydrocyclone, and feed pressure has almost no effect on the distribution characteristics of both vertical velocity and tangential velocity of flow in hydrocyclone, however the magnitude and gradient of tangential velocity are made increased obviously, so as to make the high density particles motion velocity to the wall increased and to make the cyclonic separation effect improved. The simulation results also show when the apex diameter increased, the pressure of the fluid field decreased, however the pressure grads in the apex district increased, and the degree of changing is different as the cone angle, which showed some interactive influence of cone angle and apex diameter on the fluid field of hydrocyclone. While the feed pressure also has almost no effect on the pressure distribution characteristics, however the its magnitude and gradient are made increased accordingly, which can improve the separation accuracy according to particle density.

Jan 1, 2014

By ?. S. Potokin

"In general the electric pulse treatment is composed from two processes – electric pulse grinding and electric explosive (electric discharging) activation. The electric pulse grinding with the effect of selective destruction refers to a major slag fraction, more that 2-5 mm, when a one can see a physical prerequisites for electrical breakdown of the slag particles. The electric pulse treatment of slag is considered as an additional operation in the technological scheme extraction of non-ferrous metals from copper smelting slags in addition with mechanical grinding, flotation enrichment and acid leaching. Studies of the reprocessability of pelletized slag have shown the possibility of higher extracting non-ferrous metals via flotation after electric pulse disintegration (EPD) treatment. By using EPD of slag pellets, it is possible to increase the non-ferrous metal yield to concentrate by 18-24%.INTRODUCTION The use of the explosive effect of the plasma discharge channel at electrical breakdown of a solid at a pulsed high voltage is the physical basis of the electric pulse method of destruction of geomaterials (Vorobiev et al., 1971; Andres, 1995; Semkin et al., 1995). The flowing of a pulsed current in the discharge channel is accompanied by a sharp increasing of plasma’s temperature and pressure, leading to a supersonic expanding of the discharge channel, the formation in the solid of intensive mechanical tension field, spreading of cracks, and eventually, to the destruction of the solid. Fragmentation and grinding of ore and mineral aggregates by electric pulse method due to a number of specific physical mechanisms of power load and crack formation, belonging only to this method, is different by high selectivity of destruction. This ensures better liberation of grains of individual minerals and their better preservation from destruction and less formation of a slurry output. These features creates the prerequisites for a more complete extraction of a useful mineral in the concentrate during ore dressing, to improve the quality of concentrate. In contradistinction to mechanical methods, electric pulse technology does not contaminate the product with instrumental metal, material of lining and grinding bodies. The possibility simply and in a wide range to change the dynamic load character allows to regulate the granulometric composition of the product of grinding, to obtain a narrower class of product size than is possible with mechanical grinding. The product of electric pulse grinding is characterized by less roundness and large specific surface area of grains due to the trait, that a new surface is formed in the process of splitting during the expanding of cracks. The degradation product has increased sorption and reactivity in chemical reactions. Liberation of the mineral inclusions particle better corresponds to their initial natural state in the rock and this is the great importance for the study of mineral raw materials."

Jan 1, 2018

By J. Masinja

The mining industry is known to be a potential major contributor to the industrial development of any economy. Large-scale mining has been going on in Zambia for the last 100 years. The impact of mining in Zambia has been to create a development corridor along the line of rail to the Copperbelt Province, where hitherto, mining was concentrated, and then to develop a large consolidated high-density economic zone covering an area of about 72 km by 60km. This area is home to a number of very large integrated copper/cobalt mining complexes. The mining zone has expanded to the Northwestern Province in the last 10 years, where the largest copper mine in Africa now exists, having produced about 300 000 tonnes of copper in 2011. The total output of the Zambian mining industry is now about 820 000 tonnes per annum with projections of reaching 1.5 million by 2015, due to new Greenfield investments expected to come online by then. These new mining industry developments have come on the back of strong and sustained high base metal prices, in the last 10 years or so, due to demand mainly from China and India. This new lease of life has increased the contribution of the sector to the national treasury. The mining industry in Zambia has undergone a very important ownership restructuring with the sale of the previously Government owned parastatal, Zambia Consolidated Copper Mines (ZCCM) which dominated the sector, to allow for private sector participation. The privatization process lasted from about 1995 to about 2002. The recent growth of the mining sector has unfortunately not been matched by an adequate supply of skilled manpower for various reasons. These include: (i) A lack of strong in-house training strategies by the new mine owners (ii) Decrease in industry support to the training institutions (iii) The demise of and restructuring of ZCCM which has consequently limited the Government human resources planning tools for the mining sector (iv) The cyclic nature for the fortunes of the sector has lead to fluctuating interest of student recruitment into training institutions (v) Limitations, both staff and equipment, in the training institutions (vi) A re-structuring of the training institutions This paper examines the current status, and student output from tertiary training institutions for the mining sector in Zambia. This is then compared to the skilled labour demands of the sector. The various cause and effect issues are considered and a proposal on how this skills gap could be addressed sustainably is proposed. Keywords: skills gap, graduate training, quality of graduates

Sep 1, 2012

By J. Finch, F. Rosenblum, McGill University

The self-heating of sulphides can be a major hazard in mining operations and concentrate handling, particularly during transportation and associated storage. Self-heating results from the oxidation of sulphide minerals and can vary from being insignificant to potentially hazardous to life and infrastructure. It is essential that there be a reliable test methodology that can categorize a given sulphide material as to its self-heating potential. By their nature, sulphide ores and concentrates are complex and variable mineral combinations making it difficult to predict their self-heating behavior a-priori based on mineralogy or with a simple "snapshot" test. Furthermore, self-heating behavior will depend on the state of oxidation of the sulphides as well as time, temperature and humidity. A review of available testing apparatuses and protocols that can be used to assess self-heating potential is presented. Each of these methodologies was examined in relation to its ability to predict the latent self-heating hazard of a sulphide material. Several of the methods were compared to illustrate their strengths and weakness. The results indicated that a number of the test protocols may produce false negative indications of self-heating potential, constituting an obvious concern to the industry.

Jan 1, 2014

By D. Moradkhani

The heap leaching of oxide copper ores with copper cathode recovery by solvent extraction and electrowinning is now well established as a low-cost method of copper recovery. The main purpose of this study was to extract copper from the copper low-grade oxide ore of Chodarchaei mine using column leaching. The copper oxide ore contained 1.1% Cu and 1.75% Fe. The mineralogical analysis indicated the malachite (Cu2(OH)2CO3) was mainly composed of oxidized phases. The sulfuric acid leaching experiments were performed under the laboratory conditions. The influence of several parameters on the course of the reaction such as particle size, acid concentration, flow rate, and time was examined. The optimum collective extraction of copper and iron was obtained at a particle size of +10-15 mm for a leaching duration of 3 days with sulfuric acid concentration of 100 gpl and using a flow rate of 2.5 cc/min. Under these conditions, the recovery of copper and iron were 98.54% and 41.99%, respectively. Keywords: column leaching, copper, iron, working diagram.

Sep 1, 2012

By Xiao Ni

Alkyl hydroxamic acid was shown to be a suitable collector for the flotation of pyrochlore from carbonatite niobium oxide ores. In the direct batch rougher flotation from the ore without desliming, over 85% of the pyrochlore can be recovered at about 30% mass pull. Cleaner flotation tests showed that the rougher concentrate can be upgraded. The adsorption mechanisms of octyl hydroxamic acid (OHA) were studied by using high purity pyrochlore and calcite mineral samples and employing analytical measurements such as Fourier transform infrared spectroscopy (FTIR), X-ray photoelectron spectroscopy (XPS) and UV/VIS spectroscopy. FTIR showed a shift of the vibrational frequencies of the carbonyl group in hydroxamic acid after adsorption on pyrochlore and calcite, and the shift was more pronounced on pyrochlore. XPS results indicated a lowering of the binding energies (chemical shift) of Nb3d5/2 and Ca2p3/2 electrons on pyrochlore, and the lowering of the binding energies of Ca2p3/2 electrons on calcite, again with the shift being more pronounced on pyrochlore. The results indicated hydroxamic acid formed stronger complexes with pyrochlore than with calcite. Adsorption isotherms indicated that OHA adsorbed more on pyrochlore than on calcite at low concentration. At high concentrations, the adsorption densities on both minerals were similar. All results explained the observed selectivity of the reagents in the flotation of the carbonatite niobium oxide ores.

Sep 1, 2012

By M. Evertsson, M. Johansson

"In minerals processing control is vital to increasing performance and output of a plant. Model predictive control (MPC) is one of the most effective control strategies used in process industry. Sbárbaro (Sbárbaro and Del Villar, 2010), Asbjörnsson (Asbjörnsson, 2015), and Légaré (Légaré et al., 2016) have for example highlighted the possibility to simulate, develop and tune control systems using plant simulators within minerals processing. In more recent years the use of model predictive controllers have increased, and many process industries now utilize more advanced control methods to regulate their processes, raising the question regarding how to, build, test and verify a proposed control solution successfully. In this research, a linear model predictive controller is formulated and applied to a simulator of an existing tertiary crushing circuit. The circuit has in previous work by Johansson (Johansson, 2017) been modeled in MATLAB Simulink and calibrated relative plant data to an average error of less than 10% over 8 hours of production. The work demonstrates how to formulate the controller model structure to describe conveyor belts, storage components, screens, crushers, and control objectives for a minerals processing circuit. The work illustrates how to apply and successfully evaluate possible upsides in a circuit. The advantage of a crushing circuit simulator is that it can be configured, tuned and modified in any possible way, which is of great benefit to developers and engineers. Additionally, examples of how to use estimated measures to improve the performance of the plant are demonstrated. The control performance is finally evaluated for three different controller configurations."

Jan 1, 2018