Search Documents

By Kyle Kershaw

Micropiles are routinely used in the United States for foundation support and stabilization of slopes. In recent years, several retaining walls have been constructed using micropiles in an A-frame type configuration to support temporary and permanent excavations at sites with limited access and limited right-of-way. Typical A-frame micropile walls consist of a row of vertical micropiles at the face of the wall and a row of battered micropiles extending into the soil or rock to be retained. The two rows are then tied together with a pile cap such that the front pile acts primarily in bending and the back pile acts primarily in tension. Because of tight right-of-way constraints at a residential site in Aspen, Colorado, it was not possible to construct the wall using conventional shoring systems or micropiles in the typical A-frame configuration. Rather, the wall was designed such that the row of battered piles was installed at the wall face and the row of vertical piles was installed adjacent to the property line behind the wall. As a result of the reverse configuration of the A-frame wall, FLAC, a two-dimensional, finite difference software program, was used to model the soil-structure interaction. The final wall design consisted of both temporary and permanent retaining wall sections with maximum heights of 26 feet. Inclinometers were installed in several piles to monitor the behavior of the retaining walls during and after excavation. This paper presents an overview of the design method, a discussion of construction techniques, and a comparison between the FLAC model and the measured behavior of the wall in the field.

Jan 1, 2007

By Richard Stone, Rouzbeh Afsharhasani, Moses Karakouzian

"Caliche, a hardened sedimentary deposit of calcium carbonate that occurs worldwide, generally in arid or semiarid regions, is frequently encountered in Las Vegas, Nevada. The presence of a caliche layer in a soil profile affects the response of deep foundations to axial load. This paper studies the stiffening effect of caliche layers on the elastic settlement of a pile foundation. In order to evaluate the response in a layered soil-caliche profile, finite element analyses were performed on a typical-sized single pile and a pile group, both having constant diameter and length of the pile. The results indicate that the stiffening effect from the caliche is noteworthy, and a layer with a relative thickness of at least one pile width, regardless of its location, reduces the pile settlement for both single piles and group of piles systems by at least 50%.IntroductionThe presence of cemented materials in the soil profile influences the settlement response of foundations. One type of cemented material that can be found in arid places around the world is a sedimentary deposit of calcium carbonate called caliche. Caliche, a hardened sedimentary deposit of calcium carbonate, is common in arid and semi-arid urban areas, such as Las Vegas, Nevada (Wyman, et al. 1993).Caliche is mostly observed in lacustrine, river, and alluvial fan deposits (Jr.C.C 1970). It is also found in Central and Western Australia, the Kalahari Desert, the High Plains of the Western U.S., and the Sonoran Desert of the U.S. and Mexico.Some conditions required for the formation of caliche are that country or basement rocks must be a carbonate type, carbonate must be present in the soil zone of the area, climate regime is semi-arid to arid, there exists widespread capillary activity, and carbon dioxide (CO2) is present in the environment. As a result, caliche occurs as a product of the carbonization process (Atabey, Atabey and Kara 1998). In such areas where foundations are constructed on thin rock layers (caliche), special geotechnical design conditions should be considered, particularly if the supporting rock layer is underlain by a weaker material."

Jan 1, 2015

By Aditi Sharma, Sumanta Haldar

Scouring of soil is the major concern forthe various hydraulic structures built in the flowing rivers since scouring impacts the bearing capacity of foundations. Hence, consideration of scouring in the design of foundations for hydraulic structures is crucial. Pile groups in bridges are subjected to combined vertical and horizontal loading due to self-weight, live loads, vehicular impacts, wind load, earth pressure, and current. Hence, an assessment of the combined bearing capacity of pile groups subjected to scour is essential for the safety of the structure. This paper aims to analyze the bearing capacity of pile group supporting the bridge under combined loading i.e., Vertical (V) and Horizontal (H) loading subjected to local scour. Three-dimensional finite element model (3D-FEM) of a 3 x 3 pile group embedded in homogeneous sandy soil is established in Abaqus (2018). Mohr-Coulomb plasticity model is used for the soil domain. The pile group is modelled as linear elastic. Finally, V-H yield envelopes are obtained with and without scour. The potential impact of different parameters, such as angle of attack, flow velocity, depth of flow, and different pile length-to-diameter ratios (L/D) and spacing-to-diameter ratios (S/D) of pile group on V-H yield envelopes is studied.

Sep 1, 2022

By Abolfazl Eslami, Fatemeh Rostami, Sara Heidarie Golafzani, Mohammad Arabameri

Collapsible loess is classified as problematic soil found in most continents. The loess immediately collapses under stresses induced by axial compressive loading or the soil weight when exposed to moisture. In Iran, vast areas of the Golestan province are covered with aeolian loess deposits. This paper investigates whether the simultaneous effect of inundation and pre-loading in helical pile installation are operative and effective in improvement of Golestan loess. The effect of installation conditions on loess collapsibility is studied via two main approaches, i.e., field investigations and physical modelling. The experimental studies include installation of eight single helix piles in the Amirkabir University of Technology Frustum Confining Vessel, i.e., FCV-AUT. Also, four single helix piles with embedment depth of 3 m and diameter of 250 mm were installed in Golestan province and full-scale pile static loading tests were performed. The results indicated that the simultaneous application of crowd loading and water pressure during installation of helical piles results in better soil shear strength parameters. Moreover, high crowd stresses or low crowd stresses accompanied by water pressure during pile installation brings about similar load-displacement behavior of model piles installed in FCV-AUT and full-scale helical piles.

Oct 1, 2022

By Brett K. Mainer

In the summer and fall of 2007, Drill Tech Drilling and Shoring, Inc. designed and built three 24-foot inside diameter shafts in Northern California using soil mix panels for support. The soil mixing was performed using the Bauer Cutter Soil Mix (CSM) method, by which rectangular soil mix panels up to 71 feet deep were arranged in an overlapping manner to form a 24-foot inside diameter circle. The shafts were then excavated to depths up to 51 feet. One of the shafts was a test shaft and used only the soil mix panels for support. The other two shafts were located immediately adjacent to the Mokelumne River and were used as access pits for a microtunnel drive under the river. These two shafts had wide flange beams embedded in the panels and were supported with several levels of ring steel placed during excavation. This project was the first use of the Bauer CSM method in the United States. The CSM method has been used extensively in Europe and Asia, but never for this application and never with this high a loading criteria due to water head and microtunnel reaction forces. Soil conditions at the river crossing shafts consisted of sands, gravels, and cobbles over top of sandstone and conglomerate bedrock ranging in strength up to 5,000 psi. Groundwater was within several feet of the surface. The shafts were successfully completed between October 2007 and January 2008, and the microtunnel was successfully completed in February 2008. This paper provides discussion regarding selection of the shoring type, structural design, the soil mixing method, and the mix designs. Shaft construction, shaft performance, and the capabilities of the CSM equipment are presented.

Jan 1, 2008

By Tomio Tsuchiya

A construction method of bored steel H piles enclosed in soil-cement columns was developed by modifying steel H piles from the driven pile method and soil-cement walls from the earth retaining wall method, the latter of which produces cut-off walls and reduces noise and vibration during construction. In this method, as shown in Figure 1, rich mix cement paste is injected into the bottom of a borehole which is pre-excavated by a casing auger, then a steel H beam is inserted before it hardens. Since the high vertical resistance of piles created with this method has already been confirmed by loading tests, we have been investigating the applicability of this method for piles used to temporarily support building loads for top-down construction on raft foundations until the raft foundation is completed. However, in the loading tests, the bearing capacity at the lower end of the pile was measured by loading from ground surface on test piles which had friction cut to eliminate the shaft friction resistance. In other words, the loading tests neglected the effect of overburden pressure of soil above the lower end of the pile. To investigate the effect of the overburden pressure on the bearing capacity at the lower end of the pile, loading tests were carried out on a bored steel H pile of lm diameter (test pile) bored in a compacted sandy soil layer with N-value of 100 to 250 at each stage of a three-step excavation. The results show no significant change in the bearing capacity at the lower end of the pile when the depth ratio of the pile is in the range of 5.7 to 22.7.

Jan 1, 1996

By F. M. Abdrabbo

Flight auger bored piles are formed by screwing a continuous flight auger into the ground, and pumping cement/sand grout or concrete down the hollow stem of the auger as its withdrawn. The auger is driven at the top by hydraulic or electrical motor and is guided by a vertical crane leader. Loading tests on concrete piles are described. The stability plot method is used to drive the shaft friction and the end bearing load components of the pile capacity. This paper outlines features of crucial construction factors that affect the geotechnical capacity of this type of piles. These factors include, vertical speed of auger during boring, grout factor, grout pressure, number of reborings, type of material, and slump of concrete used to form the piles. Two of these factors are highlighted in this paper. It was found that, shaft resistance is independent of grout factor, whilst point resistance increases as grout factor increases. Nevertheless the engineer should decide the safe pile load associated with the most economical grout factor. High vertical speed of auger during boring of piles may cause disaster for the adjacent buildings, due to soil decompression.

Jan 1, 1993

By Bill Zietlow

A micropile and soil nail underpinning system was installed to support a building immediately adjacent to a 25-ft deep excavation in downtown Salt Lake City, Utah. Both the building and the underpinning were instrumented to monitor deflections, rotation and crack growth. The underpinned structure consisted of a two story concrete masonry unit (CMU) building founded on shallow spread footings attached to a concrete high-rise building on spread footing two floors below grade. The face of the excavation was 10 in. in front of the underpinned building foundation wall. The underpinning system consisted of small diameter hollow bar micropiles installed with injection grouting techniques below the bottom of the excavation and attached to the underpinned structure by a concrete pile cap doweled into the existing footing. The lateral loads imposed by the soil under the underpinned structure were designed to be supported by the soil nail wall installed through the micropiles during excavation. The settlement monitoring instruments consisted of crack gages, optical survey prisms, high sensitivity vibrating wire water levels and biaxial vibrating wire tilt meters. They recorded maximum movements of approximately 0.1 in. of settlement, 0.05 deg. rotation (top of wall rotating away from excavation) and up to 0.08 in. of crack opening during the excavation until one month after the soil nails and shotcrete facing were completely installed. This movement was well within both the estimated settlement and the estimated settlement tolerance of the underpinned structure.

Jan 1, 2008

By Vijaya Bhushan Rao, Jason Redgers

A mixed-use development comprising of multistoried residential towers, retail and associated infrastructure covering an area of 500,000 m2 is under construction in Dubai. The subsoil conditions consist of calcareous sands with high carbonate and shell content with hard and competent strata encountered at varying depths. To achieve the design requirements of soil stiffness, friction angle, limit differential and total settlements and mitigate the liquefaction due to a seismic event then ground improvement were deemed necessary. In order to provide the most time and cost efficient solution numerous techniques were applied to meet the requirements for all depths such as Vibrocompaction, VC (depth >8m), Dynamic Compaction, DC (depth < 8m)] and Rapid Impact Compaction, RIC (depth <4m). The specified ground improvement requirements were translated into a target Cone Penetration Test, CPT line that served as the defacto performance requirements for the project. Suitable correction factors were applied to the CPT results to account for the high carbonate content following the works of Al-Homoud and Wehr 2006, Belotti and Jamiolkowski , 1991 and Vesic, 1965. Furthermore, the alpha factor, α, used to obtain stiffness from CPT results was applied following A.C. Meigh 1987 and Massarsch & Fellenius, 2005 where high over consolidation ratios (OCR) could be demonstrated.

Sep 8, 2021

By Vijaya Bhushan Rao, Jason Redgers

A mixed-use development comprising of multistoried residential towers, retail and associated infrastructure covering an area of 500,000 m2 is under construction in Dubai. The subsoil conditions consist of calcareous sands with high carbonate and shell content with hard and competent strata encountered at varying depths. To achieve the design requirements of soil stiffness, friction angle, limit differential and total settlements and mitigate the liquefaction due to a seismic event then ground improvement were deemed necessary. In order to provide the most time and cost efficient solution numerous techniques were applied to meet the requirements for all depths such as Vibrocompaction, VC (depth >8m), Dynamic Compaction, DC (depth < 8m)] and Rapid Impact Compaction, RIC (depth <4m). The specified ground improvement requirements were translated into a target Cone Penetration Test, CPT line that served as the defacto performance requirements for the project. Suitable correction factors were applied to the CPT results to account for the high carbonate content following the works of Al-Homoud and Wehr 2006, Belotti and Jamiolkowski , 1991 and Vesic, 1965. Furthermore, the alpha factor, α, used to obtain stiffness from CPT results was applied following A.C. Meigh 1987 and Massarsch & Fellenius, 2005 where high over consolidation ratios (OCR) could be demonstrated.

Sep 8, 2021

By Nicholas P. Gura

This paper presents the analysis, design, and load test program results for drilled shafts to support a 70-story hotel tower and associated 10 story podium structures located in Las Vegas, Nevada. A mat foundation for the structure, although feasible, would have produced undesirable differential settlements within the high rise tower footprint and at the interface with adjacent lower level podium structures. The resulting foundation system solution for the 70-story, approximately 800-foot long hotel tower was four-foot diameter drilled shafts, extending 100 below shaft cutoff. The design compression capacity for the four foot diameter drilled shaft was 5,000 kips. The load test program proved that the unique Las Vegas valley geology lends itself to efficient installation, precluding the need for engineered slurry or casing. The load testing program included the installation of two four-foot diameter test shafts to 100 feet below theoretical cutoff and the performance of two highly instrumented independent Osterberg load cell tests with maximum sustained test loads of 12,000 kips. Sonic caliper testing was also performed to document actual in-place shaft diameters and verticality. The load test program also provided information necessary for the foundation design of the podium structures. In addition to the tower?s drilled shaft load test program data, continuous flight auger (CFA) pile evaluation and testing was also performed. The CFA testing consisted of traditional ?top down? loading techniques and was performed as an alternative to the recommended shallow drilled shafts for the lower level podium structures. The results of the CFA test program provided supplemental, insightful soil friction data which was used in conjunction with the drilled shaft test program data in evaluating the most appropriate support for the lower level structures.

Jan 1, 2007

By Donald T. Robertson

This paper presents case histories of driven concrete pile damage detected with dynamic testing methods utilizing strain gages and accelerometers embedded in the pile at the prestressing yard during pile construction. Data from the embedded instrumentation is compared with data taken with external bolt on instrumentation and other test methods such as low strain testing on the same pile. In the most severe cases, the piles were extracted revealing and corroborating the embedded data collector results.

By Alexander Blatt, Franz-Werner Gerressen

Power Point Presetation at DFI 2022

Sep 1, 2022

By Andres M. Baquerizo, Matthew E. Meyer, Carlos Ortiz

"The Metropolitan Miami development, a downtown mixed-use complex developed by Miami-based MDM Development Group, has weathered the economic downturn by adapting to the needs and pressures of the local market. The development (a.k.a. Met Miami) epitomizes the term “mixed-use urban development” with its combination of condominium ownership, rental apartments, hospitality, office and retail components within Miami’s urban core. Initially conceived and conceptualized in 2004, the development has gone through several concept changes. Today, the global USD $900 million development approaches completion.The foundation evaluation, design and construction for this development included the use of innovative and state-of-the-art augered-cast-in-place (ACIP) piles. The testing for these elements included (1) the first-ever, multi-level O-cell load test of an ACIP pile, (2) a world record 5,200 ton (46,261.5 kN) equivalent top load test of an ACIP pile, and (3) continued the advancement of the ACIP pile industry to include the deepest and largest diameter pile installation to date. Those dimensions were up to 36 in (914 mm) in diameter, and 120 ft (36.6 m) deep. The project showed ACIP piles were a proven alternative for structures exceeding 70 stories in South Florida.The development includes four parcels. Met 1 and Met 2 are completed, and the construction of the Met 3 development is just beginning, with completion expected in 2014. Once the Met 3 development is completed, the design and construction phases of the project will have spanned a decade. The Met Square portion of the development, which will be a retail and cinema component, is proposed for the parcel between Met 1 and Met 2."

Jan 1, 2012

By Trevor I. Addenbrooke

Stress reducing piles were used for the first time at the Queen Elizabeth II Conference Centre near the Palace of Westminster in London, UK. The inclusion of these piles directly beneath heavily loaded columns was to reduce the high anticipated bending stress in the foundation raft, and to eliminate local yield of the London Clay beneath the column locations. Load cells were placed in one of the stress reducing piles during construction. The data showed that the pile carried about 30% of the column load. This can be contrasted with conventional piled raft design where the pile carries upwards of 80% of the column load. The build up of load on the pile and pile displacement have been accurately reproduced using coupled finite element analysis. These numerical results demonstrate the value of geometrically simple axially symmetric analyses for modelling a pile-enhanced raft. On site, excavation preceded construction of the raft and subsequent pile loading. Failure to model this construction sequence caused the shear strength to mobilize at the base of the pile first, during loading, whereas following the construction sequence caused the shear strength to mobilize at the top of the pile first.

Jan 1, 2002

By P. D. Arumairaj, B. Vani

"Micropiles are small diameter cast insitu reinforced grouted piles and it has been effectively used in many applications of ground improvement. It increases the load carrying capacity of soil and reduces the settlement. It is also used in strengthening existing foundations. In this study, the effect of Solid and Hollow micropiles on the load carrying capacity of footing resting on sand is studied. The effects of solid Micropiles are investigated by conducting experimental model studies. The parameters involved in this study include the position of pile, pile length and pile spacing. Load test was carried out on a model footing resting on sand with solid and hollow micropiles. Load test trail is repeated for footing on Micropiles with varying lengths of 10, 20, and 30 times the diameter and spacing equal to 5, 4, 3, 2 times the diameter. The load-settlement behavior of each case is compared. Optimum length and optimum spacing of both the solid micropile and hollow micropile are determined. It is also observed that the effect of micropiles in the peripheral of footing resists lateral displacement of soil underneath the footing. The micropile beyond significant depth becomes redundant.INTRODUCTIONA micropile is a small diameter (less than 300 mm) drilled and grouted pile that is typically reinforced - FHWA-NHI 2005 (Federal Highway Administration-National Highway Institution). It is constructed by drilling a borehole, placing a steel reinforcing element into the borehole and grouting it. Hollow micropiles are typically reinforced by solid central bar that occupies about onethird of the hole volume. The grout is placed by gravity, under pressure methods or by a combination of both (post grouting). Thus, micropiles can be considered as small drilled-shafts that are specially drilled and grouted.Historically, micropiles have been introduced in Italy as a foundation system mainly for retrofitting and underpinning of structures that had sustained damage during World War II and access for conventional piling equipment was not possible (Bruce, 1988). The second generation of micropiles is a pressure grouted piles with a central mono all thread bar (with diameter up to 89 mm). They are installed by using either an open or cased hole drilling method.A new generation of micropiles, termed Grout injection bore micropiles (IBOR), was developed in the 1980s. The IBOR, currently named hollow bar micropiles, utilizes a continuous all-threaded hollow steel bar as the drilling and grouting conduit, which allows drilling and grouting simultaneously without the need of a casing during drilling. A sacrificial (lost) bit with openings that allow for pressure grouting of the hole is threaded onto the end of the hollow bar and is left in place following drilling. A drilling fluid (air, water, or grout) is introduced through the hollow bar and allows the spoils to flush from the borehole opening. Upon reaching the required depth, neat cement grout is then injected under high pressure into the drilled hole to fill the annulus between the bar and the soil from the bottom to the top. Due to the grouting method employed, the shape of the hollow bar micropile is expected to have a bulb shape with an enlarged base."

Jan 1, 2015

By Thomas Billups, Brendan FitzPatrick, Doug LeDo, David Carchedi

"Working in urban environments presents unique logistical challenges beyond those typically associated with traditional geotechnical analysis and design. These challenges often include working on sites with limited access and laydown area, vibration concerns for adjacent structures and the need to work from variable elevations or within excavations. This paper describes the use of the modular Ductile Iron Pile system, a low-vibration driven micropile, on two urban projects on the Johnson & Wales University campus in Providence, Rhode Island. The paper describes the successful implementation of Ductile Iron Piles installed to develop capacity in end-bearing on one site and friction on the second site. Design, installation and quality control operations are all presented as well as the results of full-scale load testing performed on non-production test piles. This paper is of importance to the industry because it describes a versatile option for project teams as an alternative to traditional micropiles, helical piles or other deep foundation systems for urban sites.INTRODUCTIONWorking in urban environments presents unique logistical challenges beyond those typically associated with traditional geotechnical analysis and design. These challenges often include working on sites with limited access and laydown area, vibration concerns for adjacent structures and the need to work from variable elevations or within excavations. Two recent projects in downtown Providence, Rhode Island faced a combination of problematic soil conditions and urban construction challenges including vibration concerns. Both projects were a part of the Johnson and Wales University campus development. Figure 1 illustrates the urban locations of the sites."

Jan 1, 2016

By Paul Doherty

The offshore wind sector is booming on a global scale, with the U.S. becoming a front runner in this highly progressive market. The Global Wind Energy Council has highlighted the exponential growth in both fixed bottom and floating projects in the years ahead, with global installed capacity set to exceed 300 GW by 2030. This growth in installed capacity is primarily related to fixed bottom projects, which have dominated the market for the past 20 years. However by the tail end of this decade, floating projects are likely to become

Oct 1, 2022

By Anne Lemnitzer

Full-Scale cyclic field testing was performed on a 3x3 pile group consisting of nine cast-in-drilled-hole (CIDH) reinforced concrete shafts and a comparable single-shaft in order to investigate group interaction effects, derive p-y curves for reinforced concrete fixed head piles and to validate currently available p-multiplier models. The piles are identical in diameter of d=2 ft and were tested in similar soil conditions. The single pile as well as in three piles within the pile group were instrumented with internal sensor instrumentation to record pile curvatures. External instrumentation was used to control and measure the lateral displacement of the specimens. Experimental studies were supported with analytical models to enable comparisons and offer design recommendations. All test specimens were tested to structural failure and group interaction factors ranged between 0.8 at small displacement levels and increased towards unit near structural failure. A set of p-multipliers was found to reproduce an accurate fit to the available test data.

Jan 1, 2010

By Amy B. Cerato, Shawn Allred, Tatiana Vargas

"Helical piles are deep foundation elements that resemble, and are installed like, a large steel soil screw — they have a slender steel shaft with one or more round helix bearing plates welded to the shaft to provide support to the structure they hold. Helical piles are rotated into the ground with a large torque motor and provide support through soil bearing on the helix bearing plates and along the shaft. The piles are available in many lengths and, due to their small footprint along with their ability to create minimal disturbance to surrounding structures, they are often used in urban settings for foundation repair, retrofitting existing buildings and for new construction projects. Helical piles are routinely installed as foundation elements in seismically active areas, such as New Zealand, Japan and the U.S.Anecdotal observations (e.g., from New Zealand, Japan and the U.S.) have shown that piles with a comparatively small cross-section and high anchoring capacity, such as helical piles, are beneficial for seismic resistance. This is presumably due to the pile’s slenderness, higher damping ratios, ductility and resistance to tipping uplift. In New Zealand, it was observed that helical pile foundations fared much better than driven and drilled concrete piles after the 2011 Christchurch earthquake. In a personal communication, Woods (2016) described that, out of the 300 structures in center city Christchurch that were supported by helical piles, fewer than 10 structures suffered significant structural damage. However, many structures supported by driven and drilled concrete piles were damaged to such an extent that they were condemned and subsequently demolished."

Jan 1, 2017