Search Documents

By A. M. Hadian

The use of dolomite refractories in steel making and cement industries has advantages over other basic products particularly in countries where this type of refractories is produced. Due to existence of high-quality dolomite deposits in many regions of Iran, there is a good potential for producing dolomite refractories in the country. This study focuses on the effect of such additives as iron oxide and alumina on hydration resistance and density of Iranian dolomite. It was found that addition of Fe2O3 is more effective than Al2O3 on increasing density as well as resistance to hydration of dolomite.

Jan 1, 2004

By M. S. Alam, Jae-Chun Lee, M. Tanaka, K. Koyama

Extensive research work is being carried out at AIST for developing energy saving green technology for base and precious metals recovery. In the present work, a new flowsheet is developed for copper recycling from waste electronic circuit board where copper was recovered by leaching followed by solution purification and direct electrowinning of Cu(I) from ammoniacal alkaline solution. In this new technology, power consumption in EW circuit was greatly reduced. This paper describes the overall process with an emphasis on different aspects of solution purification where impurities were selectively removed by cementation and solvent extraction techniques under nitrogen atmosphere.

Jan 1, 2004

By Jocelyn Koshinsky

The uranium milling process at the Key Lake Operation of Cameco in Northern Saskatchewan, Canada results in the leaching of untargeted metal(loid)s such as arsenic, iron and nickel that are found at high concentrations in the ores. To mitigate the environmental impact of the leached As, Fe and Ni in the mill waste solution (raffinate), the pre-discharge mine tailings (rafffinate and residue) are neutralized with slaked lime, resulting in the formation of secondary As-, Fe- and Ni-bearing mineral phases which serve to control their concentrations to very low levels in the tailings porewater. As part of an ongoing investigation into the long-term evolution (10,000 year) of arsenic mineralogy in the Deilmann Tailings Management Facility (DTMF) at Cameco?s Key Lake Operation, it has become necessary to characterize secondary As-bearing mineral phases during the neutralization process prior to the discharge of the tailings and compare these to in situ As-bearing mineral phases in the tailings facility. This is primarily to determine if changes have occurred over time to As-bearing mineral phases in the tailings facility as well as to investigate whether alternate neutralization techniques may have a beneficial effect on the stability of mineral phases formed. Thus a bench-scale model was developed and preliminary testing conducted to simulate the mill neutralization process (i.e. neutralization of synthetic raffinate solutions with incremental amount of slaked lime to terminal pH values). The resulting ?tailings? (precipitates and supernatant) were then separated and analyzed. XRD analysis of the precipitates shows that the Fe occurred mostly as ferrihydrite. This was complimented with results from Raman spectroscopy which further indicated that the As appeared adsorbed onto the ferrihydrite. Results of geochemical modeling of the bench-scale test compared well with supernatant profiles from ICP-MS analysis.

Aug 1, 2010

By Mike Power

Geophysical techniques have played a pivotal role in northern kimberlite exploration since the initial discovery at Point Lake in 1991. In the Slave Craton and surrounding regions, there are definite contrasts in physical properties between kimberlite intrusions and surrounding bedrock. Kimberlite commonly displays higher magnetic susceptibility, distinctive remnant magnetism, low electrical resistivity and lower density than surrounding rocks. In addition, the distinctive geometry of kimberlite pipes is reflected in geophysical responses which further facilitates target discrimination. There has been an evolution in geophysical exploration strategies over the past 12 years. Helicopter total magnetic field and electromagnetic (HEM) surveys have proven to the most cost-effective means of conducting first pass investigations in prospective areas. During the early 1990's, total magnetic field and frequency domain electromagnetic surveys were virtually the sole techniques employed during follow-up surveys. Inevitably, the initially high rates of kimberlite discovery declined in the areas surrounding the original finds. Marginal magnetic and EM anomalies were all that remained to be tested and this spurred interest in the improvement of existing interpretation algorithms and in the application of additional complementary techniques to reduce the exploration risk. Gravity has become a popular third survey following the deployment of the Falcon (TM) airborne gravity gradiometer system by BHP Billiton in 1999 and improvements in ground techniques. Ground penetrating radar (GPR) has proven to be particularly useful in delineating kimberlite pipes following drill discovery and in exploring for kimberlite dykes in settings where indicator mineral trains indicate such targets are likely. Seismic methods have been tested for both reconnaissance and delineation but remain underemployed. Given the high cost of drilling in the North and the proven success of geophysical techniques in reducing exploration risk, it is likely that an increasingly diverse range of geophysical techniques and innovative interpretation techniques will continue to be applied in kimberlite exploration.

May 1, 2003

Owner?s Team and EPCM ?Teams rolesmay vary to suit the skills available, however the tasksremain the same ?Ensure adequate level of capability in the team ?Large owner?s teams vssmall owner?s teams ?size of owner?s teams can reflect not only the individual level of capability but also the type ofrelationship with the EPCM contractor ?Wholly owned projects vsjoint ventures projects ?Both cases require clear accountabilities and authorities ?Project sponsor should be a senior executive with commercial andtechnical accountability of project outcome ?Project leader should be experienced and have solid leadership capabilities ?Attention should be paid to balancing personality types in an owner?s team

May 1, 2010

By Xiao Huang, Dongmei Wang, Prakash Patnaik

Further increase in gas turbine engine temperature necessitates continuous development and advancement to thermal barrier coatings. While tremendous effort has been devoted to developing new thermal barrier coating materials and processing methods in order to decrease the thermal conductivity, limited attention has been paid to radiative thermal transport through coatings. It is the purpose of this study to develop a new layered coating structure that can be used to effectively reduce the both radiative thermal transport as well as thermal conductivity, and to demonstrate the mechanism and effectiveness of the proposed multilayered structure. Mathematical modeling based on the multilayer quarterwave stack and simulation results are presented.

Jan 1, 2004

By Peter McBride

Human excellence in all areas of endeavour is acknowledged and recognized. Establishing role models and spreading the word on best practices helps broader audiences. For on-the-job safety, recognition awards are a component of successful programs. In Canada?s mining industry since 1941, the John T. Ryan Safety Trophies initiative has contributed to the sector?s improving record in this area. The much sought after and rich in history John T. Ryan trophies are recognized symbols of safety excellence in Canada. The effectiveness of the Ryan safety recognition program in Canada has led to its export to other mining countries seeking to improve their overall safety performance.

May 1, 2008

By Tracy-Lynn Humby

A recent report commissioned by the South African Chamber of Mines, Mining Vision 2030, identifies the South African mining industry?s negative legacy, its exploitation of people and the environment, as the single biggest hurdle to maximizing the industry?s impact on national development. Industry leaders have identified the need to put the past ?to rest?. With reference to three recent cases involving members of the South African mining industry, this paper points to the continuities between the past and present. It argues that the metaphor of ?multiple crossings? is more generative than the notion of putting the past ?to rest? for purposes of engaging with mining?s negative legacy.

Aug 1, 2013

The Rabbit Lake In-Pit Tailings Management Facility contains frozen layers of tailings due to subaerial deposition during the coldest periods of winter. Thawing is required to ensure full consolidation of the tailings and to regain disposal space presently occupied by ice. Electric resistance heating has been used to heat soil for bitumen extraction and remediation of volatile contaminants. A preliminary evaluation of the application of electric resistance heating to thaw about 0.3 cubic metres of frozen tailings was conducted using tailings frozen at about -2 oC. Visible thawing of the tailings mass was observed after 25 hours, demonstrating the feasibility of this approach.

Aug 1, 2010

By M. F. Vancas

Control of the interface elevation between the aqueous and the organic phases in typical settlers is a fairly straight forward principle. However, when looking at the details involved in actually designing the aqueous and organic discharge launders and weirs, one comes to realize just how sensitive the system is to small variations in operating conditions and/or parameters. This discussion focuses on the details that must be considered during design, looks at the various types of control systems typically used (from the basic manual systems through to full automation), and equally importantly, looks at what happens in an operating plant when the conditions and/or operating parameters change.

Jan 1, 2007

By Y. Dong, L. Li, L. Yu

Converter slag has become an important secondary raw material. Consequently, vanadium bearing converter slag is of great interest for the recovery of vanadium. Solidified converter slags are made up of three main mineral components: dicalcium silicate, calcium ferrite and wustite. Vanadium in modified slow cooling down converter slag of Magang is found mainly concentrated in a separate mineral phase. The mineral phase with high content of vanadium (24%, wt, V205), concentrating 83% of vanadium, can be separated from the slag for economical vanadium recovery. Some characters of the mineral phase were discussed comparing with dicalcium silicate, one of the typical mineral phases in converter slag studied well.

Jan 1, 2004

By A. Yoshida, H. Miura, S. Yamaguchi, Y. Oyama

A discussion is given on the ionic equilibria and precipitation reactions in seawater based on thermodynamic analysis, in order to understand the solubility of nutrient salts from dephosphorization slag for marine phytoplankton. Solubility of constituent ions in aqueous solution in equilibrium with solid phases are determined using thermodynamic data. It is proposed that CO2 potential defined as log Pco2 should be considered as an additional parameter to the Eh- pH diagram for the ionic equilibrium of slag components in seawater, since magnesium and calcium carbonate precipitation reactions determine the solubility of ligand ions in nutrient salts, such as phosphates, silicate, and sulfate.

Jan 1, 2004

By J. Aguilar-Santillan, H. Balmori-Ramirez, R. C. Bradt, I. Vernet-Patiño, F. Cunha

Kyanite is an alumino-silicate mineral that has been widely used for the production of refractory products for industrial applications. Kyanite provides a high alumina content, it readily produces mullite during firing, good hot strength of products and can be adapted to produce dimensional stability of products during firing. This research addresses the application of kyanite in mixes to produce (0 dense mullite aggregates with the addition of alumina, (ii) dense composite refractory aggregates of forsterite / spinel with additions of magnesia, and (iii) dense cordierite aggregates with the addition of talc. Effects of attrition milling and conventional ceramic processing are addressed as they affect the properties of these unique aggregates.

Jan 1, 2004

By Peter Lighthall

What is an engineering firm?s role? ? The ideal situation is a life of mine service alliance with the owner ? Engineering firms are long term custodians of information ? Maintain consistency with established closure objectives, adjust closure plans to meet changing situations and technologies ? Develop range of solutions and present owners with risk profile The mine closure planning process ?new mines ? For metal mining, geochemistry is the issue ? The planning process: ?Sampling ?Waste characterization ?ARD prediction ?ARD control strategies ?Life of mine waste management planning ?Assessment of residual impacts ?Development of strategies for dealing with residual impacts ?Estimate closure costs ?One time decommissioning and reclamation costs ?Ongoing treatment/maintenance costs

May 1, 2006

By E. Kordzadeh, M. Reza Bateni, M. Karaminezhaad, A. Moeini

A series of austenitic heat resistant Fe-Ni-Cr-Al alloys with different nickel contents have been investigated at 1100 ° C and 25, 50, 50,100 hours in S/0 bearing atmospheres. Before sulphidation test, the specimens were annealed in argon at 1250 °C for 8 hrs. Weight changes were measured using an automatic thermo gravimetric analyzer and corrosion products were analyzed by scanning electro microscope (SEM), energy dispersive X-ray spectrometry (EDAX), X-ray diffraction and optical microscope. The results showed that sulphidation resistance decreased with increasing nickel content. Internal sulphidation controlled by gaseous transport through cracks and pores and the formation of internal sulphide increased when liquid sulphides formed on the surface.

Jan 1, 2004

By R. von Bonsdorff

Electrochemical and quartz crystal microbalance (QCM) methods were used to investigate the dissolution rate of gold in a solution similar to those utilized by the Outokumpu HydroCopper® process. The measurements were conducted in an electrolyte solution where [NaCl] = 2.8-280 g/L, pH = 1-2.5, [Cu2+] = 0-30 g/L and T = 70-95°C. According to these measurements, the solution flow has the greatest impact on the dissolution rate of gold in the HydroCopper® process. Under adequately acidic conditions (pH < 3), the dissolution rate of gold increases with increasing cupric concentration, increasing chloride concentration and increasing temperature. The results and trends observed compared well with the literature.

Jan 1, 2007

By R. Niechcial

As populations grow and industry expands, the limited fresh water resources available are increasingly under stress. This situation creates conflict between communities and industry; and the sustainability of both is threatened. The symbiotic relationship between community and industry highlights the need to develop innovative solutions to these water shortages. The sea may hold the key to providing the resource to permit the development of industry, the sustainability of communities, and the protection of the dwindling legacy water resources around the world. Desalination technologies have developed to where it is now economically viable to create industrial and potable water quality from seawater. Nowhere is this development more important than in the arid region of Northern Chile, where high copper prices have encouraged a boom in mine development.

Jan 1, 2007

By Melinda Bissinger, Frederic Berube

Environmental considerations are important in the aerospace industry. To that effect, several elements such as engine emission, noise and materials are identified by the industry and the society as requiring significant improvements for future and current products in order to be aligned with current expectations. In this context, the industry is addressing this opportunity by investing significantly in new engineering solutions that will meet greener targets. To this effect, the impact of material choice is significant and will make a difference in the forth coming solutions. Several opportunities to develop more efficient products, quieter aircrafts using materials and manufacturing processes that will be more respectful of environmental considerations exist. The presentation will cover those elements and provide an overview of the upcoming solutions.

Jan 1, 2010

By O. Kangal, G. Önal, G. Bulut, A. Gül

The recovery of copper and cobalt from the ancient copper slags, located in Küre-Turkey, is investigated. Fayalitic type of ancient copper slags containing 1.41% Cu, 0.53% Co and 53.16% Fe were subject to the experimental study. Magnetic separation, gravity concentration and flotation test were conducted. The results of magnetic separation and gravity concentration were not satisfactory. However, a concentrate containing 9.57% Cu could be produced with 44.7% recovery by flotation. Copper and cobalt that remained in the flotation tailings was recovered by roasting with sulfuric acid followed by hot water leaching. Complete cobalt dissolution was observed in 1 hour of roasting at 150°C and 3:1 acid/slag ratio, whereas the copper recovery was 83%.

Jan 1, 2004

By M. R. Coffin

In recent years, improved operation of the Kidd smelter has resulted in an increase in blister production capacity. Due to manpower and equipment limitations anode production and treatment rates could not be increased without incurring significant additional operating expenses. The option chosen to expand casting and refinery capacity to meet the available blister supply was to increase the anode thickness while maintaining the same anode exchange cycle in the refinery. This has resulted in a cathode production increase of almost 10% for minimal expenditure. Equipment and process modifications required to cast and refine the thicker anodes are discussed in this paper, along with the Six Sigma methodologies used to identify them. Key areas covered are Hazelett continuous caster operation, refining process parameters, plating performance and cathode quality.

Jan 1, 2007