Search Documents

By R. S. Forgan

The synthesis and study of a systematic series of phenolic oximes have shown that substitution in the 3-position can greatly affect extractive efficacy. Solid state, solution and gas phase analytical techniques, including X-ray crystallography, EPR and IR spectroscopy and collision induced dissociation mass spectrometry have been assessed for their applicability in interpreting the origins of differences in extractant strength. The dominant substituent effect on pH0.5 is the change in ligand pKa, with the more acidic ligands being stronger extractants. The influence of the 3-substituent on the stabilising intracomplex H-bonding of their copper(II) complexes also affects extractant strength. The 3-NO2 substituted ligand shows the lowest pH0.5 value, due to a combination of its low pKa and a stabilising bifurcated H-bond assembly around the copper(II) centre. Appending an aminomethyl group to the 3-position gives a ligand capable of binding a metal and its attendant anion. These metal salt reagents show potential to open up new flowsheets for the processing of high tenor copper feeds.

Jan 1, 2007

By P. V. Barr, Y. -H. Li, A. P. Watkinson

Subsequent to a campaign of pilot-kiln trials of firing bio-oil and natural gas, scale-up to commercial lime kilns was made using an in-house mathematical kiln model. Both dry limestone and lime mud kilns of 3.5 m OD. by 100 m length were used for bio¬oil firing simulations. Comparisons were made against natural gas firing on the basis of specific firing rate, off-gas volume, energy consumption and overall lime quality. Model simulation results indicate that conversion from natural gas to bio-oil with no productivity loss will increase energy comsumption by about 7.5% and total off-gas volume by about 8%. Alternatively, a 6% decrease in productivity would be expected if off-gas volume is maintained constant. The calculations are sensitive to deviations in the lower heating value (LHV) used in the simulations. A 5% increase in the LHV of the bio-oil, which could result from a 3% decrease in the moisture content, reduces the energy penalty to 2% coupled with a slight reduction in off-gas volume.

Jan 1, 2004

By K. Soldenhoff

Mantra Resources Ltd is developing the Mkuju River project is southern Tanzania. The uranium deposit, hosted in ?Karoo? sandstone, is surface outcropping with the majority of uranium mineralisation occurring in the finer clay component of the ore. A flowsheet, consisting of ore beneficiation, acid leaching, RIP uranium recovery and direct precipitation of the uranium product, was developed and successfully demonstrated in continuous mini-plant operations at ANSTO. The selected flowsheet overcomes the difficult slurry rheology, arising from the clay component of the ore, by eliminating the need for a CCD plant. The RIP process was found to contribute to a high uranium extraction, by eliminating ?preg-robbing?, at a relatively low acid addition in leach, with the potential to eliminate ferric ion and oxidant additions.

Aug 1, 2010

By Arne Renström

A fleet management system such as Minestar with CAES and Aquila could basically be defined as a tool for production control and distribution of drill and load maps, but should also be considered as continuous improvements and a never ending production study. The objective of production studies is to establish facts to be used for production improvements. In a mine operation there are many issues to improve and they spread from achieving productions plans, drilling precision, improved spotting while loading to equipment utilisation. This gives that there is not one single key value to present; we need to manage information presented on maps, as trends, graphs, tables and pre-calculated data for ?free-use? normally in spread-sheets to be able to turn data into useful information.

May 1, 2003

By Ian Thomson

OBJECTIVES OF EXPLORATION ? Prove/Disprove presence of potentially economic mineralization ? Keep on budget ? Minimize negative environmental impacts ? Gain a ?Social License to Operate? (SLO) WHAT IS A ?SLO? ? Granted by the local community ? Intangible, informal, non-permanent ? Has to be earned and then maintained ? Defined as ? Ongoing Approval (BSR and AccountAbility) ? Ongoing Approval, broad social Acceptance (Joyce and Thomson) ? Ongoing Acceptance (Nelson, and many others) ?Expression of the quality of a ?relationship?

May 1, 2010

By Michel Aubertin

Mining activities can produce large volumes of waste rock, which are typically deposited in piles on the soil surface, above the water table. Such piles can cover areas of several tens of hectares and can reach over a hundred meters in height. For hard rock mines, the waste rock grain size can vary from silty particles to metre-scale blocks. The internal structure of a pile constructed on a relatively flat surface typically includes two main zones. The first zone corresponds to the heart of the pile, and is formed by several sub-horizontal stratifications (with dense and loose layers) due to the heavy mine equipment traffic which induces local compaction and degradation of the waste rock. The second zone corresponds to regions where waste rocks are deposited by push-dumping or end-dumping close to the external flank of the pile, inducing grain size segregation along the slope. Depending on the deposition sequence, grain size distribution and bench height, a gradation may then be observed, with coarser particles (with cobbles and blocks) near the base and finer particles near the crest, together with inclined stratifications due to the advance of the deposition face. These internal features affect the distribution and flow of water (and air) in the pile. To assess the internal distribution of material properties within the pile, a combination of several tools is usually required which can provide information on the hydrogeological and geochemical characteristics of the waste rock. In this regard, geophysical tools are very interesting because they can lead to a threedimensional mapping of property variations. The information gathered from a combination of appropriately selected techniques can be used to construct numerical models to further study unsaturated water flow and reactive transport. Such simulations help better understand the pile response in its actual and future states, which in turn provides input to adjust the deposition sequence, to plan for closure, and to select an in situ groundwater monitoring strategy. The presentation will give an overview of techniques that have been developed to characterise material properties in the laboratory and in the field, and to obtain a general picture of a pile?s internal structure. Additional results on unsaturated reactive transport modelling will also be shown to illustrate how the internal pile structure may influence its hydro-geochemical and environmental response.

Nov 1, 2008

By A. Chaisantikulwat

Most solid-oxide fuel cell (SOFC) modeling emphasizes steady state cell operation. However, understanding the dynamic behavior is essential to predict the performance and limitations of SOFC power systems. In this work, we demonstrate a dynamic model of a SOFC, and we simulate a feedback control scheme that can maintain output voltage despite load changes. Dynamic response is determined as the solution of coupled partial differential equations derived from conservation laws for energy, mass and electric charge. From such a model, the step responses to system input variables can be determined. Low order dynamic models that are sufficient for feedback control design can be derived from the step responses. The development of the partial differential equation model is outlined, and the limitations of the control system are discussed.

Jan 1, 2005

By Blandine Arseneault

The Raglan Mill had been in production for less than a year when the initial toxicity tests on the effluent revealed that it was defined as ?toxic? under regulations. Testwork was begun to address the fundamental reasons for the toxicity and a systematic approach was initiated to identify causes. Elimination of the problem presented a challenge once the main conclusion identified high dissolved solids as the principal culprit. In particular, normally benign soda ash (sodium bicarbonate) reagent additions used in milling, was identified as the main contributor to the problem. Following analysis of all requirements and safety considerations, a concept to recycle 100% of the mill process water was pursued. In addition to meeting regulatory requirements, this project would have numerous positive benefits to the operation, including reducing fresh water consumption and lowering costs.

Nov 1, 2002

By J. D. Galloways

The northern part of the P. G. E. railway traverses and opens up that part of the province known as the Cariboo district, comprising the Cariboo and Quesnel Mining Divisions, which are a part of the Northeastern Mineral Survey District. Williams lake, a divisional point on the P. G. E. is near the southern boundary of the Quesnel Division and from this point the railway runs northerly to Quesnel, its present terminus. From Quesnel the railway is projected and partially constructed to Prince George on the Canadian National railway; therefore its general trend is northerly through the heart of the Cariboo district. Early History There is no need to outline at any length the early history of mining in the Cariboo. It is sufficient to say that the great gold rush to the Cariboo, in the early sixties, was practically the commencement of mining in British Columbia. These early placer mining operations centred around the old towns of Quesnel Forks, Keithley Creek, Barkerville and Van Winkle, the latter now called Stanley. Many millions of dollars of placer gold have been taken out and the end of production is not in sight yet. The maximum yearly production was reached about 1863, after which there was a gradual decline in output. During the war years production was at a very low figure but a steady, even if small, increase has occurred in the last three years and prospects are encouraging for a much greater output.

Jan 1, 1925

By Katherine (Kate) Bruce

Aurora College ? Yellowknife Campus, in partnership with the Northwest Territories Mine Training Society and industry partners, has developed a 6 ? week program on Underground Mining for delivery in Northern communities. The goal of the program is to inform and connect Northern residents to the career potential at existing and future mining operations throughout the Northwest Territories. The program content includes an introduction to the mine life cycle, basic underground mining methods, the use of technology in training via desktop simulators for underground mining equipment, safety in the workplace, and essential skills training (Ready to Work - North) and assessment. Students completing the short program may then choose to continue into a long (12-week) program to be offered at the Yellowknife Campus. This program expands upon the initial introduction and includes modules on NWT geology, environmental studies, underground mining processes and underground mining equipment operation using the larger enclosed cab simulator for a variety of equipment being used at northern mining operations. Success of both programs will depend upon a variety of factors, many of which are outside of the control of the developers of the training modules. These will be investigated throughout the presentation. Connecting northern employers with northern employees is a major concern. It is hoped that through the development and implementation of a program such as this, that the connection can be made and sustained allowing continued employment for the life of northern mining operations.

May 1, 2008

By R. B. STEWART

A few days ago, while reading a report of the late Dr. Robert Bell in preparation for this afternoon's meeting, I found some impressive figures concerning the magnitude of the Hudson Bay basin. From the waters of the Bay itself, this great territory extends eastward 500 miles, westward l,300 miles to the Rocky mountains, and southward to the source of the Red river. It has a width of 2,100 miles from east to west, and a length of l,500 miles from north to south. Its area is almost three million square miles. It is not, of course, my intention to review the natural resources of this vast territory, but to confine my remarks to that portion of it adjacent to the waters of Hudson bay. A number of erroneous ideas exist in the minds of many concerning this northern country, especially as regards its latitude and climate. Burwell, at the entrance of Hudson strait, is in the latitude of 60 degrees or roughly that of the north of Scotland. The southern end of James bay has about the same latitude as the northern end of Vancouver .island.

Jan 1, 1928

By Y. Konishi

This paper reviews the mechanism and kinetics of bioleaching of chalcopyrite by the thermophilic archae Acidianus brierleyi in batch and continuous-flow reactors. Rate data for the batch bioleaching of chalcopyrite concentrate were collected to clarify mechanism of the chalcopyrite bioleaching with A. brierleyi. The chalcopyrite leaching was markedly accelerated in the presence of A. brierleyi, and greater than 90% copper leaching was achieved within 10 days. Chalcopyrite leaching took place predominantly as a result of direct attack by adsorbed bacteria on the sulfide surface, the chemical leaching with ferric iron being insignificant. Batch rate data collected under a variety of operating variables were analyzed with our batch bioleaching model, in order to estimate microbial kinetic and stoichiometric parameters for the microbial growth on chalcopyrite. The batch model and the estimated parameter values were used to find optimum operating conditions. Moreover, the batch model was extended to describe the bioleaching in continuous-flow stirred tank reactors. Simulations based on the continuous reactor model and the estimated parameter values were used to predict the leaching fraction as a function of the number of reactors connected in series.

Jan 1, 2007

By Serge Vézina

Environmental issues have evolved considerably over the last two decades. The main contributing factors, to name a few, have been the changing values of our modern societies, the globalization of trade and its linkage to environment, evolution and accessibility of information/communication technologies, better educated populations, climate change, long range transport of toxics and the increasing influence of NGOs and multistakeholders. As well, environmental management of mining operations had to be realigned in order to meet these new realities and to respond to more elaborated regulations oriented towards sustainability. Environmental Management Systems (EMSs) have emerged and have been introduced to meet not only the assurance of conformance to regulations but also to prevent pollution and to apply the continuous improvement of mining processes. EMS models have been developed and certification to international standards (e.g. ISO-14 001) is a common practice. Globalization has imposed challenges and additional requirements to environmental management. Developing a mine in emerging countries implies dealing with international agencies, local communities and a variety of government infrastructures to obtain a ?licence to operate?. This paper presents the structure of our EMS and how we have adapted its implementation to our operations in South America.

May 1, 2003

By Jacek Paraszczak

As the deposits located closer to the surface are getting depleted, more and more Canadian mines produce ore from considerable depths. Deep mining represents a number of serious challenges including high rock temperature. Conventional diesel powered loadhaul- dump machines and trucks so widely used in metal mines constitute an additional source of heat and noxious gases. Due to this, they have a substantial adverse impact on a quantity of fresh air required and a cost of ventilation, particularly since the mines have to meet more and more stringent regulations in this respect. In this context, the paper examines possible alternatives for diesel powered equipment, both these commercially available as those at the stages of prototypes or under development. They are reviewed with regards to their principles, required infrastructure, stage of technology development and its progress. The questions of their flexibility, practicality and economic viability are also addressed. Following the above a potential for their implementation and possible benefits (if any) in the conditions of deep Canadian mines is discussed. The paper concludes with short to medium term predictions concerning the most promising drive alternatives for vehicles destined to operate in deep metal mines.

Feb 1, 2008

By M. Schwarze

SMS Meer GmbH with its COPPER PLANTS DIVISION produces a full line of systems and machines for the processing of copper. The product range includes: shaft melting furnaces, anode casting lines, horizontal and vertical casting lines, casting and rolling lines for copper wire rod and strip, cold pilger mills, planetary rolling mills as well as tube drawing equipment. The new designed shaft furnaces are the most economic way of copper melting. The CONTILANOD® system with hydraulic shear represents a breakthrough into higher production capacities and improved geometrical accuracy of anodes. The new generation of CONTIROD® lines with individual drives of rolling stands guarantee cost effective production of highest rod quality. A new horizontal continuous casting technology for the production of tube shells as feed stock for the copper tube manufacturing process ? directube® was developed and introduced into production. A first line for continuous vertical strip casting - called VERTICAST® - for higher production rates and improval quality of cold-rollable strips is in the final stage of commissioning. These innovative technologies increase product quality, reduce process costs and help for a wide use of copper in all sectors of life.

Jan 1, 2007

By A. Morales

Flue dusts from a copper smelting furnace (continuous furnace), have been extensively characterized. The main phases detected have been cuprospinel, anhydrous copper sulfate (chalcocyanite), lead sulfate (anglesite) and arsenic oxides (claudetite and arsenolite). As minor phases, zinc sulfate (zincosite) and several copper or copper/iron sulfides were detected (digenite, anilite, bornite, cubanite), and also a copper oxide (tenorite). The suspension of this material in water leads to the partial dissolution of copper and zinc (chalcocyanite and zincosite) and arsenic oxides. The hydrocyclone classification of the residue makes it possible to obtain two fractions: a copper-rich coarse fraction and an arsenic-rich fine fraction. The coarse fraction can be recycled to the smelting furnace and the fine fraction can be mixed with wastewater sludge from a paper factory, to make both residues inert before disposing them to landfill.

Jan 1, 2007

By M. Amsden

"Since the computer program is far from complete this must be only a brief progress report on the computerization of flotation metallurgy at the Ecstall concentrator at Timmins.Ecstall is currently treating about 10,000 tons per day of two different ore types. One is a low sulphide copper-zinc ore, the other is a high sulphide lead-zinc-silver ore. The concentrator is divided into three individual grinding and flotation circuits. In effect there are three mills under one roof. Normally there are two circuits on copper-zinc ore and oneone lead-zinc-silver ore. At this point in time one of the copper-zinc circuits is under computerized metallurgy control.The first step in this control is the use of an ARL on-stream x-ray analyzer, coupled with a Honeywell 21 computer which types out assays and recoveries for each individual circuit. Our approach to a computer program was to keep it simple. The program was written to coincide as closely as possible to what an operator would do in the performance of his duties based on the in-formation he was getting from the x-ray analyser read-out. Initially, computer control was put on just the copper circuit of the ""A"" Division, controlling the collector addition at three points in the circuit; primary, secondary, and scavengers. The control was based on recoveries and the grade of the copper concentrate. Targets like 95% recovery and 24% copper concentrate grades that it was felt the circuit could achieve were set to start with. It quickly became apparent that this alone was not enough because if on a certain ore the best recovery that could be made was only 94.9% the computer kept calling for more reagents until the circuit was completely out of control. On another ore it might have been quite possible to get 96% recovery but when the set point of 95% was reached the computer stopped trying for any more. To overcome this problem a very simple optimum seeking program was devised by one of the Ecstall staff and it has worked very satisfactorily since being put into use in July 1970.In the copper float only the two collectors R-208 and the xanthate R-317 are under computer control. The addition of frother and depressant is left to the operator. The flotation cells have automatic level controls which can be adjusted by the operator. pH is controlled automatically through a lime loop-sensor arrangement."

Jan 1, 1971

By R. Pelletier, Herny. E., C. Allaire

Corrosion of refractory linings by molten metals is controlled by interactions between penetration and chemical reaction. Corrosion of aluminosilicates by molten aluminium is no exception. The early stage of corrosion can be described as a particular case of reactive wetting over a porous medium. Although the reactivity between aluminium and silica is great, which should improve wetting and penetration, the presence of air and the formation of a protective oxide layer disfavours initial penetration. This paper presents the results of an exploratory study on the effect of some parameters on the initial stage of aluminium penetration. Penetration kinetics and metal intrusion tests have been performed on alumina and silica powders with pure aluminium and Al¬5%Mg. Capillary models are used as tools of interpretation. Penetration kinetics tests had a poor reproducibility and the kinetics itself can not be explained very well by the capillary-tube-bundle model. On the other hand, a capillary model initially developed for ice intrusion into freezing soils produced predictions in reasonably good agreement with intrusion pressure measurements. The effect of particle size and alloy composition can be predicted using this model. However, the effects of temperature and powder chemistry need additional interpretations to be rationalised. An unusual resistance to penetration of silica powder by molten aluminium have been observed in a series of experiments. This led the authors to the strange conclusion that oxygen should be seen as an excellent non-wetting agent and that there might be ways to use it in industrial applications.

Jan 1, 2004

By Alireza Entesari

Removal of metal ions from effluents represents a significant technical challenge. As a consequence several industries, including mining, are faced with issues relating to removal of contaminant cations and anions from solution. This study evaluates three natural mineral materials referred to as basalt, scoria, and calcined shale for treatment of metal contaminated effluents by adsorption. Adsorption tests were conducted to asses the possibility of removing cationic and anionic metal ions from prepared solutions and mine water effluents. Sustainable production of industrial minerals requires that a diverse range of added value products be introduced.

May 1, 2006

By F. Rojas, M. Sanchez, J. Palacios, O. Pavez

Copper sulfide is the main mining resources in Chile, and most of this metal is obtained via pyrometallurgical extraction in seven copper smelter plants, which extends from the northern Atacama desert to the central part of the country. In 2002, 1,522,000 metric tons of fine copper were produced, with a notorious environmental impact due to the large amount of slag generated, including transportation and disposing problems. Therefore, there is a great interest in finding alternative uses in order to give additional value to the slag. This is a total project development concept, which consider residues as new resources where new components could be obtained, improving sustainability in mining activities and also ensuring clean production processes. Thus, the present work shows a review of copper slag characterization as well as several ways of utilization, including compact material for road and railway installation, part of admixtures in concrete.

Jan 1, 2004