Search Documents

By M. P. Amsden

"Ecstall Mining is a wholly-owned subsidiary of Texas Gulf Sulphur at Timmins, Ontario. The mill tonnage is 10,000 tons per day of two different ores, a copper zinc ore and a silver lead zinc ore, producing about 2400 tons of concentrates per day. These are as a copper concentrate, a high silver zinc concentrate, a low silver zinc concentrate and a silver-lead concentrate. For flotation recovery a very fine grind is required, about 80% minus 325 mesh and the concentrates produced are 40% minus 10 microns.The thickened concentrates are pumped to the filter floor for filtering and drying. The filtering and drying section is separated from the flotation section by a wall and is controlled from a dryer control room by one operator.Two operating panels are located in this control room. One contains stop-start controls for the thickeners, filter motors and vacuum pump motors, and stop-start controls for dryer feed conveyors and dryer product conveyors to concentrate load-out bins, as well as ammeters for conveyor drive motors. Dryer throughput is regulated by Merrick Type L weightometers located on the dryer discharge conveyors and recorded on tons per hour strip charts.The second panel contains the temperature strip charts, furnace drive ammeters, scrubber and exhaust gas controls, burner controls and panel alarms for the four dryers.Filtered concentrates are dried in Nichols-Herreshoff, multiple hearth, dryers consisting of nine hearths (zinc) and seven hearths (copper and lead). There are two dryers for handling zinc concentrates and one each for copper and lead concentrates. The dryers are heated by burning natural gas. Each zinc dryer handles 1,000 t.p.d. and the copper and lead dryers 750 t.p.d. each.Multiple hearth dryers are unusual in the base metal mining industry and the reasons for selecting them in preference to rotary dryers are as follows:1) The concentrates could only be filtered to 15 to 17 percent moisture. These sloppy filter cakes would be extremely difficult to handle in rotary dryers."

Jan 1, 1972

By G. L. Spence

Prevention of cuprous and cupric oxide formation on stored ETP copper rod is a major concern for copper rod and wire producers. During normal storage periods copper oxide layers can increase from less then 100 A to more then 1000 A exceeding ASTM specifications and discoloring the rod surface. Various types of corrosion inhibitors are tested and compared in effectiveness for prevention of copper oxide formation on stored copper rod. Aromatic triazole compounds are also compared to a non-azole containing compound.

Jan 1, 2007

By Sadough vanini Ali

The silicon anisotropic wet chemical etching technique is widely employed for fabricating various microelectromechanical system (MEMS) structures for advantages such as simple etching equipment and its capability to fabricate special microstructures. In this paper, we consider a complete theoretical derivation of the analytical solution based on geometrical and kinetic aspects of step flow on any surface and with a mathematical method we derive new equation for calculating the microscopic etch rates of surface atoms for a new range of concentrations and temperatures. Furthermore, a novel equation is presented for the calculation of the microscopic activation energies for some typical surface atoms and a new comparison of activation energies between some atoms is made that divides atoms into three categories. The results demonstrate agreement with the experimental results.

Oct 1, 2011

By H. Dundar

The first application of High Pressure Grinding Rolls was in 1985 at a cement plant, for the purpose of capacity improvement. Then various circuit configurations were derived to achieve a reduction in overall specific energy consumption, by transferring more of the grinding required to the HPGR. In most circuit configurations, the recycle of fines is required for effective breakage between the rollers. By increasing the fines amount in the feed material to a specific level within the recycling load, a uniform material bed is created and a higher pressure gradient along the roller width is obtained, resulting in compact flakes, including more fines. The fines recycle results in enhancement of the interparticle breakage. This paper will discuss the effect of the feed size distribution on HPGR performance.

Jan 1, 2012

By M. Gruber-Pretzler

Technical Sn- bronzes tend to form both macrosegregations and microsegrega¬tions during DC-casting due to the particular thermodynamic properties and kinetics of phase transformation. As a result a heterogeneous cast microstructure forms that is some¬times a reason for a decrease in workability. The extent of macrosegregations in DC-casting can effectively be influenced by casting parameters like casting velocity, primary cooling or inlet geometry which in fact change the relative flow between the melt and the forming solid. In order to understand the influence and interaction of the related phenom¬ena, simulation methods are applied. The solidification of the strand as well as the forma¬tion of macrosegregation are simulated with a two phase volume averaging model. The velocity field of the melt flow is explicitly calculated by solving the corresponding mo¬mentum conservation equations. Within the mushy zone the local formation of microseg¬regations in the presence of feeding flow is estimated. The thermodynamics of the Cu-Sn system is accounted for and it is distinguished explicitly between interface and average concentrations. To investigate the influence of feeding flow on the formation of mac-rosegregations, a study has been performed. Based on this result, the phenomena of mac¬rosegregations are described in a detailed discussion.

Jan 1, 2007

By M. Fooladi Mahani, M. R. Izadpanah

The knowledge of the thermal shock resistance of refractory materials is of outmost importance due to their wide range of applications in various industries, namely; ceramics, oil refinery, thermal insulation, nuclear power, chemical and petrochemical industries. Thermal shock resistance is measured in terms of the number of cycles that a refractory material can withstand when subjected to sudden temperature changes. This property is measured experimentally by heating a sample of the material and cooling it in a known environment then the number of cycles it withstands this treatment without spalling is a measure of its thermal shock resistance. Although this method of experimentation has long been the practice, but it is both expensive and time consuming. Various studies have been carried out to predict this vital property, however, the rang of applications are limited. The present study employs a test rig by which temperature distributions in magnesite samples are accurately measured. This information plus other results obtained from relevant tests on related properties are used to develop a model which predicts the number of quench cycles withstand by different materials when subjected to sudden temperature changes. The comparison of the theoretical values using the solution of the presented model with experimental data for different materials having different thermal resistance shows a closed agreement.

Jan 1, 2004

By C. F. Gleeson

"I HAVE BEEN ASSIGNED the pleasant task of adding a last word in way of summary to this session. I think that the trend set in having a geochemical session at the CIM Annual General Meeting is a good one and I hope it will continue so that members of the mining fraternity can get together on a regular basis and discuss geochemical problems peculiar to our Canadian scene. A series of interesting papers have been presented on what has been considered by many in the past as not only a problem area for geochemistry but even an impossible one. The papers should help dispel some of these fears. Lack of development of geochemical techniques in the Shield has been due to a variety of factors, many of which have been mentioned. However, I feel that one of the main reasons for this lack of development has been timidness on behalf of many people to get out and do the necessary work which helps produce answers to many of the questions asked. New developments and applications of geochemical methods in the Shield will not be done by the faint of heart but by those who have the curiosity, interest, imagination, drive, resources and, most of all, the intestinal fortitude to stick to it and not give up because results or conditions do not meet with preconceived notions. Another element that will be needed by those who will successfully apply the techniques and who will be responsible for new breakthroughs is the systematic approach to sampling and analysis and the integration of geochemical, geological and geophysical results. Erratic sampling patterns - a sample here and a sample there - generally lead to more problems than solutions."

Jan 1, 1971

By K-A. Adamson

If fuel cells and hydrogen are to become a mass market reality a substantial amount of further research and development needs to be undertaken. Work in hydrogen storage, production, the economics of all aspects of fuel cells and hydrogen, materials balances, and product integration are just a few of the areas that are under focus. Setting R&D targets, and providing R&D funding are therefore areas that are central to the long term development of the market, and areas in which a number of governments worldwide are highly active. Some governments, such as Japan and Korea, have set a number of very ambitious, highly focused, long term targets and are backing this up with substantial funding, others such as the EU are working on a more integrated approach, wrapping some fairly fundamental R&D into large integrated projects which run in combination with a number of other market aspects, such as public acceptance and roadmapping. The US is slightly different, in that although is has a number of long term programmes and targets, FreedomCar and SuperGen being just two, the levels of funding are set annually with the passing of each years Fiscal Budget. This paper takes three high profile regions and analyses the R&D targets and funding levels for fuel cells and hydrogen. Criteria that will be looked at include: Time frame of target(s), level of ambition, funding issues, including: Funding windows, levels available, funding barriers, overall programme goals. The added value to this paper is that it will provide a clearer picture of where each region is heading, what are its strengths and weaknesses, in terms of R&D and where there may be areas for potential international collaboration.

Jan 1, 2005

By J. A. Hillier

The staff of the Hudson Bay Mining and Smelting concentrator have developed a new type of reagent feeder. Several factors encouraged the development of such a system: varying heads caused by the mixing of ores from several mines, the increasing number of flotation circuits operated and reagent feeding stations remote from the flotation operator's work area. The reagent feeders also had to be compatible with future plans for reagent control from an on-stream X-ray analyzer and computer system. The new feeder is a positive-displacement pump set to deliver a constant volume per stroke. At a remote panel, the feed rate is altered by changing the time between strokes. The feeders have been found to be reasonably trouble-free and accurate to less than 2 per cent error.

Jan 1, 1973

By R. Ham-Su, J. P. Healey, S. P. Farrell, R. S. Underhill, M. A. Gharghouri, C. V. Hyatt, L. M. Cheng

Magnetic shape memory alloys (MSMA's) are a class of materials where magnetic energy can be converted into mechanical energy and vice versa. NiMnGa-based MSMA's have attained magnetic field induced strains up to approximately 10% and have a relatively wide operating temperature range, from well below 0°C to above RT, making them very attractive for a variety of applications. However, these materials also suffer from low toughness. Using these materials in a composite could mitigate this shortcoming, and also overcome limits imposed by inertia and eddy current losses. In this work, we describe the manufacture and characterization of such composites. Composites with 30% by volume MSMA were fabricated under a magnetic field resulting in anisotropic magnetic properties. Damping properties were evaluated by dynamic mechanical analysis.

Jan 1, 2004

Abstract - A method to extract certain types of error variance information from paired data is presented, which constitutes an important tool for the calibration of Gy’s formula for variance predictions in the sampling of broken ores. The research summarized here complements publications by others on geochemical precision. The model and method proposed for treating duplicate data provide a practical means of deriving separate estimates of the purely analytical and aliquot sampling variances, from a unique set of duplicate assays, and, hence, proposes a new avenue for estimating effective mineral grain size.

Jan 1, 1998

By M. E. Austin

Many numerical models for the tubular solid oxide fuel cell (SOFC) exist, with various degrees of sophistication. However, the question of what physics must be modelled, and what can be neglected has not been resolved. A parametric model is proposed and analyzed to quantify the influence of thermal phenomena such as reaction heat generation, cathode channel convective cooling, and thermal radiation with participating media. Currently, a three-dimensional model is used to simulate the conditions of an anode supported cell in the centre of a tube bundle. The interconnect and nickel foam spacers that bridge adjacent cells in series and parallel, respectively, are neglected thus enabling a domain consisting of a 45o azimuthal section of the tube. The conservation equations for mass, energy, and species transport are solved using commercial computational fluid dynamics software, and radiation heat transfer is also modelled using a Discrete Ordinates method. Finally, temperature-dependent material properties and reaction rates are used. The model predicts lower overall temperatures than models that do not include radiative heat exchange and more moderate temperature gradients than those that ignore participating media radiation. Further, different regimes are identified, from convection dominated heat transfer to radiation dominated heat transfer. The results can be used to aid in the selection of appropriate models for a given fuel cell operating regime.

Jan 1, 2005

"Adopted in 2003, theses guidelines are intended to assist the Qualified Person(s) in the planning, supervision, preparation and reporting of mineral resources and mineral reserve estimates. The report is divided into two broad sections “General Guidelines” appropriate for most metals and “Guidelines Specific to Particular Commodities” for potash, industrial minerals, uranium and coal. “These guidelines are reference in the Companion Policy of NI 43-101 with a statement that a qualified person classifying a mineral deposit as a mineral resource or mineral reserve should follow them.”Executive SummaryThe following is a summary, in table format, of the main elements of the Estimation Best Practice Committee's report ""Estimation of Mineral Resource and Mineral Reserve Best Practice Guidelines"". While the summary table is provided for convenience, the Committee recommends that the report be read in its entirety and the table summary not be used as a stand alone document. These guidelines are not intended to be either prescriptive or exhaustive. They do not preclude innovation. Preamble: These guidelines have been prepared by the Canadian Institute of Mining and Metallurgy and Petroleum (CIM) led Estimation Best Practices Committee. They are intended to assist the Qualified Person(s) (QP) in the planning, supervision, preparation and reporting of Mineral Resource and Mineral Reserve (MRMR) estimates. All MRMR estimation work from which public reporting will ensue must be designed and carried out under the direction of a QP in accordance with National Instrument 43-101 (NI 43-101) and related forms. A QP is defined in NI 43-101 as ""an individual who is an engineer or geoscientist with at least five (5) years of experience in mineral exploration, mine development, mine operation, project assessment or any combination of these; has experience relevant to the subject matter of the mineral project and technical report; and is a member in good standing of a professional association"". Disclosure of MRMR estimates is to be made in accordance with industry standard definitions approved by the CIM (the CIM Standards adopted by the CIM Council in August 2002) which have been incorporated by reference into NI 43-101."

Jan 1, 2003

By F. McIntosh Galbraith

EMPLOYING geophysics to find ore was for a long time considered by the Canadian mining fraternity to be a performance of dubious value: in a category somewhere between the practice of sorcery, and using a divining rod to locate underground water. With increasing knowledge, however, and with constantly improving instruments, a solid speaking acquaintance with this adolescent science is becoming an integral part of the mining geologist's stock in trade. And quite properly so: for, in the established mining districts, the ore deposits which could be easily found, by ordinary prospecting methods, have already been located. There remain; however, in almost all of the principal mining camps, areas which are covered to varying depths by glacial debris; and it is here that the obvious opportunities exist for the successful application of geophysical methods. Geophysical results must always be considered in the closest possible relation to the local geology; and, in reality, the 'doodle-bugs' are simply additional tools for the geologist (in the same category with a plane table or a microscope). The Sudbury Basin is a shining example of precisely this state of affairs. Detailed geological mapping has not significantly altered the position of the outer norite contact as placed on Dr. Coleman's original map of the district. What detailed examination has done, of course, has been to reveal the accuracy with which the contact can be placed in different parts of the district, and to show up, in consequence, areas in which further work might reasonably be expected to disclose hitherto unknown or unsuspected ore. Viewed in this light, the proportion of the norite contact which is covered by substantial quantities of overburden is astonishingly large.

Jan 1, 1939

By Fengxiang He, T. Meadowcroft, Yanjun Zhang

Slag from the zinc fuming furnaces contains about 3 percent zinc and 0.1 percent lead. The paper outlines several experimental techniques for recovering these components from liquid fumer slag. The simplest method, remelting followed by a hold period, indicated that a substantial fraction of the metal values was recoverable as a result of fuming into the gas phase, presumable by reduction of the metal ions by divalent iron ions. Following on from this, slag samples were equilibrated with copper, chosen because the activity coefficients of zinc and lead in copper are very low. This improved metal recovery, with substantial amounts of lead and zinc reporting to the liquid copper as well as to the fume. Application of an electrical emf across the slag-metal interface, using a graphite anode and a liquid copper cathode, resulted in further gains in metal recovery.

Jan 1, 2004

By Y. Kocaefe, S. Afshar, D. Kocaefe, Z. Kunt, C. Allaire

Interaction of aluminum with silica based ceramics Jose M. Soto, Jeffrey D. Smith, William G. Fahrenholtz. Department of Ceramic Engineering University of Missouri-Rolla Rolla, MO 65409-0330 USA ABSTRACT Interactions between A356 aluminum (Al-Si alloy) and dense fused silica (FS) riser tubes used for low-pressure casting of aluminum alloys were evaluated using a sessile drop approach. The tubes have a short service life, but cost and thermal shock resistance make them an effective solution. The main problem encountered during use is the reaction of aluminum with silica to form alumina and silicon, which causes failure. Tests have been conducted on as-fired (uncoated) and modified (coated) tubes. Experiments were carried out in a horizontal furnace at 1225°C under argon to minimize the effect of the aluminum oxide on the interactions at the alloy-silica interface. Images of the drop were acquired and contact angle values were estimated for uncoated and coated samples, but no significant differences in the contact angles were observed. Scanning electron microscopy revealed the presence of cracks at the interface between the reaction zone and the unreacted silica. The presence of reaction products (silicon in the reacting alloy and aluminum in a reaction zone between the alloy and the unaffected silica) has been confirmed using energy dispersive spectroscopy. A two layer coating system was found to be effective in reducing penetration of the aluminum alloy. The interactions between bed media and aluminum have been studied under static and dynamic flow conditions. An experimental system was set up simulating a small filter. Desired flow field can be created around alumina particles and velocities can be adjusted. A mathematical model was developed to predict the velocities, and this was validated using data from a visualization study. The interaction zone on the surface of the particles was analyzed with optical microscopy and SEM. This paper presents the study and compares the results under static and dynamic flow conditions.

Jan 1, 2004

UBC Mining Department As an example ?35 Graduating ?14 with Jobs ?6 with Strong leads ?149 Undergraduate ?Projecting 43 second year students ?10-30 % Dual Degree

May 1, 2010

By M. Lundström

The Outotec HydroCopper® process is a novel technology, developed and registered by Outotec Technology Oy, for leaching copper from chalcopyrite using cupric chloride solution. The leaching process is operated at atmospheric pressure in a stirred tank reactor, at temperatures near the boiling point of water and pH values between 1.5 and 2.5. During the leaching of chalcopyrite in cupric chloride solution, a reaction product layer forms on the mineral surface. In the present work, the formation and the composition of the reaction product layer was studied in an environment similar to that of the HydroCopper® process. The effect of the process parameters on the reaction product layer was investigated. Electrochemical measurements, including A.C. impedance spectroscopy and microscopic observations were carried out and an equivalent circuit was used to determine the surface parameters, such as the reaction product layer capacitance and the charge transfer resistance. The results suggest that, at low pH, a passivating sulfur-rich layer forms, whereas at high pH, a more porous iron-rich layer was detected. The values measured can give useful information for optimising the leaching parameters of the HydroCopper® process. Cu2007

Jan 1, 2007

By L. V. Volkov

The equilibrium of the CuO-Cu20-Cu+-Cu2+ system with various chloride ion concentrations in solution in the presence or absence of an oxidant was investigated. It is shown, that, regardless of the presence or absence of chloride ions or oxidant (oxygen) in the system, the process can be divided into three stages, which are characterized by differing rates and mechanisms of metallic copper cementation and cuprite precipitation and, hence, lead to differing rates of the dissolution of nickel into solution. The effect of the concentrations of chloride ion and oxidant on the phases in the process residues is also discussed. The addition of an oxidant increases the amount of cuprite (Cu20) in the leach residue. With increasing chloride ion concentrations, the rate of copper cementation increases, even without an oxidant in solution. The results of these laboratory experiments and the mechanisms developed are consistent with analysis of samples of industrial cement copper obtained from the Severonickel Combine.

Jan 1, 2007

By D. Newman

"This paper discusses the author’s work on international law norms of consultation with Indigenous communities and examines unexpected corporate stakeholder impacts on these norms. Customary international law, which governs the area, does not traditionally refer to corporate conduct. This paper surveys several sources on developing international law on consultation obligations; it also discusses the impacts these norms can have on corporate stakeholders in the mining industry. Finally, it asks how interactions of corporate stakeholders in this area can indirectly impact future law and suggests implications for different business models in the mining sector.RÉSUMÉ Le présent article traite du travail de l’auteur sur les normes de consultation avec les communautés autochtones contenues dans le droit international et examine les impacts inattendus des parties prenantes sur ces normes. Le droit coutumier international, qui gouverne ce domaine, ne réfère traditionnellement pas à la conduite des sociétés. L’article analyse plusieurs sources traitant du développement de nouvelles lois internationales sur l’obligation de consulter; il traite aussi des impacts que ces normes peuvent avoir sur les parties prenantes dans l’industrie minière. Finalement, il pose la question à savoir comment les interactions des parties prenantes dans ce domaine peuvent avoir un impact indirect sur les lois futures et il suggère des implications pour divers modèles d’affaires dans le secteur minier."

Jan 1, 2015