Search Documents

By P. Momni, D. Ersenkal

Equator Principles (EPs) are a set of guidelines developed and adopted by a series of financial institutions for assessing and managing social and environmental issues in project financing. Established in 2003, EPs are now adopted by some 68 financial institutions from 27 countries. As more and more financial institutions join this global initiative, it is important for project owners to have a logical framework embedded into the project lifecycle to reduce the risk of non-compliance which could result in costly delays. This paper outlines a proactive approach for project developers in order to integrate environmental and social aspects into entire project lifecycle.

Jan 1, 2010

By N. Sarmady, Mei Li, N. C. Parson, W. J. Poole

"The mechanical behaviour of AA6082 is a function of the extrusion conditions and in particular, the quench rate after extrusion. It is well known that precipitation of Mg-Si phases on grain boundaries during quenching can negatively affect the ductility of the alloy. In this study, AA6082 alloys containing 0.5 wt. % Mn and 0.15 wt. % Cr were direct chill (DC) cast, homogenized and then extruded to produce 3 mm x 42 mm strips. The microstructure in the as-extruded strips was unrecrystallized due to the Zener-Smith drag from the Mn/Cr dispersoids. It was shown that a solution treatment of 5 minutes at 560°C did not significantly affecting the as-extruded microstructure but if the as-extruded strip was cold rolled prior to heating, recrystallization occurred concurrently with the solution treatment. As such, 3 initial microstructures were produced, i.e. unrecrystallized and recrystallized with a grain size of 9 and 40 µm. After the solution treatment, controlled cooling experiments were conducted using the Gleeble 3500 thermomechanical simulator with cooling rates of 10, 25, 80°C/s as well as water quenched. The mechanical properties (e.g. yield stress, fracture stress and fracture strain) were determined from tensile tests for the different combinations of initial microstructure and cooling rate. The relationship between the quench rate and precipitation of Mg-Si phases on grain boundaries was examined by FEG-SEM. It was found that the yield stress decreased as the cooling rate decreased and that there was complex relationship between the fracture properties and the microstructure.INTRODUCTION As the automotive industry strives to reduce fuel consumption and CO2 emissions with the goal of reducing the environmental impact, there is a need for lighter vehicles. As a result, aluminum alloys are gaining popularity to replace steel parts as structural components. An exemplar of this is the Ford F-150 pickup truck which has an aluminum body and is ˜750 pounds lighter than the previous steel version of the vehicle. The structure includes a mix of aluminum sheet, extrusions and cast alloys. The current research is concerned with the performance of aluminum extrusions in applications such as side rails, crash tubes and other structural parts. These components experience a combination of bending, stretching and folding both during the forming of the part and in service, e.g. crash of a vehicle. There is a need to have detailed information on the influence of processing on final material performance, in particular the cooling rate after extrusion."

Jan 1, 2018

By H. J. Glass, J. G. L. Bekkers

"In order to determine the feasibility of a hydraulic ore hoisting installation, the optimal operating conditions were calculated for applying such a system at the Detour Lake Mine of Placer Dome Ltd. Next, a financial analysis was conducted in order to estimate the cost per tonne for hydraulic hoisting of the ore. Subsequently, the cost per tonne was compared with the hoisting costs associated with a new borehole hoist. Installing a hydraulic ore hoist at Detour Lake Mine was found to be feasible with considerably lower costs per tonne of ore. The applied research method appears to be very functional and can be used to do similar research for other mining operations. IntroductionThe principle of hydraulic ore hoisting is well known, yet hardly accepted in hard rock mining. Application of the system would result in a smaller diameter shaft requirement and a flexible, easily expandable system. However, underground ore size reduction might be necessary and practical experience with the system is limited. Following recent innovations in the field of pumping hardware, e.g. new GeHo and Siemag Transplan equipment, hydraulic ore hoisting should be seriously considered for certain mining operations. As a case study, a design was made for the development of the newly found QK-Zone at Placer Dome Ltd.’s Detour Lake Mine. Hydraulic ore hoisting has been compared with conventional skip hoisting by establishing the optimal operating conditions and pumping equipment requirements for similar capacities at a selected mining operation. Generally accepted equations for slurry transport were used to predict the variation of pressure and power requirements as a function of hourly production and pipeline diameter. These data are used to select suitable equipment and estimate cost figures in order to make a financial assessment."

Jan 1, 1998

By STEPHEN V. FORGERON

The Loch Lamond celestite properties in central Cape Breton Island were mined by Kaiser Celestite Mining Limited from 1970 until 1976. Poor market conditions in J976forced operations to cease. Kaiser holdings included the Lake Enon, MacRae and A mac prospects. A total of about 272,000 tonnes of raw celestite have been mined. Celestite deposits are situated in the Loch Lamond Basin, specifically in Lower Windsor sedimentary rocks. Of the five formations in the Lower Windsor Group, celestite is found in the upper four. Celestite in the Enon Formation occasionally replaces shale that separates stromatolitic dolomite columns; elsewhere in the formation it occurs in association with siltstone and gypsum. Jn the B2 Limestone Formation celestite fills pores or grades between limestone and gypsum. It replaces both limestone and silty limestone conglomerate in the Loch Lamond Formation; this limestone is of unusually high grade (60 to 70% SrSO,J for the area. Evidence indicates that the Uist Formation may hold important celestite reserves. Original celestite mineralization probably resulted from evaporation of seawater on mudflats or 'sabkhas'. Secondary mineralization also may have occurred. Strontium ions could have been leached from pre-existing concentrations and overlying gypsum, moved downdip in groundwater and combined with sulphate rich waters to deposit as celestite in porous B2 limestones.

Jan 1, 1984

By Tetsuya Yumoto, Toshikazu Shiratori

Information on the elements contained in E-Waste is important from the viewpoint of recycling. We analyzed several components of waste electrical and electronic equipment (WEEE) collected from citizens. The distributions of the minor metals in WEEE were determined with elemental mapping and chemical analyses. The annual change in elemental composition was investigated by analyzing equipment manufactured in different years. The information will be of use for separation techniques required for future advanced recycling.

Jan 1, 2011

By José J. Suárez

As pressure grows for commodity pricing, new mines are more difficult to develop, the stock markets demand better financial returns from mining companies, resources for the developing and operations are scarce, and developing countries in Asia, and Africa demand more metals, it is important that mining companies effect better utilization of capital to develop capital projects. In the last few years, the costs for Capital projects have been impacted by the following factors:

May 1, 2013

By J. Palarski

Hard coal, mined in Silesia Region as well as in the eastern part of Poland, is a key national resource. In Polish underground coal industry, modern mining technologies have been successfully tested and used in the last 50 years. More than 98% of the coal produced underground is extracted by longwall mining method. Current underground coal mining expands into increasing depths. The use of conventional coal extraction methods ? room and pillar and longwall with caving - is becoming increasingly difficult. The coal mining is modifying existing methods and is testing innovative technologies. Backfill is an important component of modern underground mining operations. In Polish underground mines, backfill is recognized as an integral component for extraction of coal from greater depths in a densely populated environment. The modifying and innovative methods require the use of backfill or grouting of caving to provide structural support in underground excavations and to ensure that the mining operations are safe. Depending on the geological structure, mining conditions and environmental requirements there are several variations of longwall methods used in underground coal mining in Poland, in particular: longwall with caving, longwall with backfill, longwall with grouting of caving area. This paper will discuss the different components of an effective longwall production and filling process of caving area. The paper will give a overview of the current application of backfill technology, focusing on Polish coal mining operations. This paper will also briefly describe how backfill contributes to an innovative method ? underground coal gasification. The paper discusses specific requirements for fill materials and the technology of backfilling for underground coal gasification (UCG) operations and problems of implementation and correlation of backfill parameters with other processes that occur during thermal processing of coal.

Aug 1, 2013

By William H. Emling

With profitability pressures in heavy industry increasing, many producers are turning to predictive maintenance as a means of harvesting untapped value from their production assets. Corporations are losing their maintenance and processing core competencies through attrition. As capital budgets are being trimmed, manufacturers are consolidating operating units into fewer, more profitable routes. Maintenance functions, however, typically receive low priority when investment is made, since many companies consider maintenance costs as ?overhead?. Condition-based monitoring, integrated to Level I and Level II process inputs, is seen as the most cost-effective solution to the implementation of predictive maintenance strategies. This paper will review the evolution of preventive and predictive maintenance programs, highlighting examples of successful application of integrated condition monitoring.

May 1, 2001

By J. Chenier, M. Boissoneault, D. Ducharme, R. Schonewille

The operation of Falconbridge's Sudbury nickel smelter has undergone significant change since the production was consolidated to a single electric furnace in 1994. In the late 1990's a capital program of about $100 MM (Cdn) was undertaken to expand and modernize the smelter. This project, known as Smelter 2000, was mainly driven by the need to process the new concentrate produced at Falconbridge's Raglan operation in northern Quebec. Included in the scope of the project was the installation of dry concentrate handling facilities, modifications to the roaster feed preparation system, installation of a matte granulation system and modification of one of the converters. Improvements to in-plant hygiene were also an important part of the Smelter 2000 project. Over the past 5 years much has been learned about the challenges in treating two significantly different concentrates. More recently, the introduction of a third concentrate from Falconbridge's new Montcalm operation near Timmins, Ontario has added another dimension to the operation. This paper will describe how the main challenges from the past 7 years have been overcome and discuss the path forward for the Sudbury Smelter Business Unit.

Jan 1, 2005

By Paul T. Fitzgerald

Risk financing solutions are emerging to fully address environmental liabilities for mining operations. Supported by specialized insurance and alternative risk transfer (ART) products, mine owners can fund, cap and guarantee the environmental liabilities and closure obligations of a mine within a financial structure that will be acceptable to regulators. An environmental risk financing program will permit an owner to transfer the liabilities and indeed the ownership of a site to a third party that has the ability and resources to responsibly execute the closure plan. A properly structured program will be financially viable for the owner and will also respond to community and environmental opposition concerns about sustainable development and the environmental legacies associated with mining activities.

Apr 1, 2005

By A. J. Basu

Air quality in underground mining operations can fluctuate significantly during the working day, but until recently the only way to ensure a mine had sufficient air quality was to over-ventilate and, with significant delay in adjusting the volume or direction of the airflow, working conditions were tolerable but rarely ideal. Underground ventilation management systems have been considered to achieve improved energy efficiency since at least 1995 in Canada. However, Mine Ventilation Optimization, (MVO) and integrating it with Ventilation on Demand (VOD) is only becoming more of a reality in the last seven (7) years. A systems approach to MVO takes into account all the elements from the point the power is distributed into the ventilation fans through to the actual quality and quantity of fresh air to the working face. Opportunities exist throughout the system for energy savings but not all of them are cost-effective. Depending on the application, these opportunities can be easily realized by properly sizing, streamlining, maintaining and operating the ventilation system using premium mine proven energy efficient components throughout. Implementation of VOD is a key step in achieving the MVO objective. However, VOD is a concept, and it requires various tools, procedures, and strategies for cost-effective and operationally viable implementations. This paper provides a historical background in the development of VOD and provides a framework for proper and cost effective implementation. In addition, an optimized ventilation system will also allow increased airflow by reducing resistances and shock losses. This turn in would allow production target improvement, which could be an attractive objective compared to energy savings. Mine ventilation is the life support system of an underground mine, and contributes to sustainable development and corporate social responsibility goals assuring health and safety aspects of strategic planning. The proposed framework addresses implementing mine ventilation optimization integrating ventilation on demand as a vehicle for energy, health and safety improvement and overall productivity gains in the mining cycle efficiency while significantly reducing carbon footprint of a mine.

Aug 1, 2013

By Tom Shumka

All mineral processing facilities that use girth gear driven mills need to inspect the gear teeth on a routine basis, whether it is every six months or every three years. The inspection frequency depends upon gear tooth condition, and the objective is to ensure operational integrity of the gear teeth. Conventional methods such as magnetic particle testing, visual inspection, or dye penetrant examinations rely heavily on interpretation. At best, these techniques can determine whether a defect exists, but are unable to provide information on defect severity. This paper describes the use of combined Eddy Current Array (ECA) and Alternating Current Field Measurement (ACFM) to provide a complete survey of all surface breaking indications on the whole gear tooth depth. This method accurately determines the size, length and depth of any cracks found on the surface.

Jan 1, 2012

By Tim Grain Joseph

This paper considers the duty cycle of an electric cable shovel and correlations with measured passive seismic responses of the underfoot oil sand material in-pit. It has been observed that the cyclic activity during operation of any shovel in the oil sands environment causes the material to deteriorate and provide a less than ideal footing for this large item of equipment, whose dead weight approaches 1500 tons with a footprint of merely 75 square yards. Consequences are manifest in the form of carbody and side frame cracks, and associated downtime, maintenance activity, cost, and subsequent loss of availability. The objective of these considerations, as part of the Oil sands Equipment Interaction Program (OsEIP); currently a joint venture between Syncrude Canada Ltd., JPi Ltd., Caterpillar Inc., P&H MinePro and the University of Alberta; is to identify and provide feedback to the manufacturer and end user adverse shovel - ground conditions. This would enable the manufacturer to incorporate greater knowledge into the design process and the end user to direct operations in an enhanced proactive maintenance stance.

May 1, 2002

By E. L. Martheleur

A general expression for the electric power generated or consumed in a direct-current circuit is obtained by multiplying the reading of a suitable voltmeter connected across the terminals by the reading of an ammeter connected in the circuit. by the reading of an ammeter connected in the circuit. When alternating currents are considered, the product of the volts and amperes as obtained for direct currents does not generally represent the true energy involved; it is greater than this true energy and should be multiplied by a certain factor which may have any value between zero and unity, according to the conditions of the circuit. This factor is called the power-factor of the system, and expresses the ratio of the true energy over the apparent energy. For a three-phase system the expression of the apparent energy is [\/ 3 x E x I; ] while the expression of the true energy, that is, energy suitable for mechanical work, is [v? 3 x E x I x cos A.] The total current of a circuit corresponds to the reading of an ammeter connected in the circuit; it is the resultant of two currents. The first of these is in phase with the voltage, and is that portion which really produces mechanical work; the second is always in quadrature with the voltage, that is it may lead or lag the voltage by 90° according to the condition of the circuit. This second current does not produce any sensible work, and for this reason is sometimes called wattless current or reactive current.

Jan 1, 1924

By Paolo Farina

Slope monitoring radar has emerged in the last ten years as a leading edge tool for monitoring movements in natural and engineered slopes, thanks to its ability to rapidly measure slope movements with millimetric accuracy over wide areas in any weather conditions, obviating the need to install artificial reflectors. In recent years, slope monitoring radar has experienced significant improvements in its performances, mainly thanks to the use of different radar technology, such as Synthetic Aperture Radar (SAR), able to overcome some of the limitations of the first generation of radar and to provide higher spatial resolution, longer working distances and faster acquisition time. One of the leading applications of this technology is today represented by slope monitoring within the surface mining industry. Prominent international mining groups currently employ slope monitoring radar, based either on Real Aperture Radar (RAR) and SAR technology, for active and background monitoring of open-pit walls. The main technical features of typical slope monitoring radar based on SAR technology along with their possible applications are presented in this paper along with recent case studies of successful slope monitoring in open pit mines.

Jun 1, 2012

"This contribution is concerned with adaptive processing decisions, where the process parameters are optimally adapted to the varying properties of the material input stream. Our starting point is the geometallurgical paradigm that the varying properties of the input stream are considered known e.g. from a geometallurgical model of the mined ore body, and optimal processing parameters are computed from them, by finding the parameter seaming optimal in a computer simulation.This approach however has to work with a lot of uncertainties: The prediction of the geometallurgical ore parameters can only be done with some geostatistical uncertainty. The parameters themselves are only proxies for true ore properties. Model prediction can differ relevantly from actual process results, due to model simplifications. Due to these uncertainties the computed processing choices can turn out to be inferior to simple non-adaptive processing. In this contribution we focus on the uncertainty of the ore properties and analyse this effect systematically, by modelling this uncertainty effect mathematically and in computer simulations. The most important findings are:(a) Processing choices not taking into account the uncertainty sometimes even perform worse than simple non-adaptive processing, for the sole reason of ignoring the uncertainty effect.(b) Ore properties, not adequately reflected in the ore description, might require different approaches, in which the observed processing behaviour feeds back into process control.(c) Bayesian decision theory allows computing optimal processing choices combining the information from the mine (geostatistical predictions) and from the process feedback. These choices give much more robust choices and do not suffer from the drawbacks described for the simple approach we started from.These new approaches can substantially improve the performance of adaptive processing in existing plants."

Jan 1, 2016

By F. Habashi

Lead is an ancient metal. The alchemists related it to the planet Saturn. It was largely obtained by smelting galena which generally contains small quantities of silver. That is why the metallurgy of lead was closely related to that of silver and in some cases the ore was treated only for its silver content. It was also known during the Roman time that lead vapors were toxic. Lead has been produced exclusively by pryrometallurgical methods. Lead refining is a complex process because of the presence of deleterious impurities such as arsenic, antimony, and bismuth. In the nineteenth century lead played an important role as a material of construction in the manufacture of sulfuric acid. In the twentieth century tetraethyl lead was used exclusively as an anti-knock reagent. In recent years lead is mainly used for making batteries.

Jan 1, 2008

By E. McLaren, J. Sanftenberg, C. Cameron, H. Dello Sbarba

"A Ventilation on Demand (VOD) system has been optimized and maintained at Glencore’s Nickel Rim South Mine (NRS) in Sudbury, Ontario, Canada for the past seven years. The system monitors and controls air quality and quantity through real-time, dynamic automation of primary fans, secondary fans, automated airflow regulators, and air monitoring instrumentation with VentSim™ CONTROL, a VOD software. This paper will focus on the implementation of testing procedures and system maintenance methods. Overall, the results show a consistent reduction in energy usage.INTRODUCTIONThe Ventilation on Demand (VOD) system at Glencore’s Nickel Rim South (NRS) mine in Sudbury, Ontario, Canada, involves the control of two 2,980 kW centrifugal surface exhaust fans with Variable Frequency Drives (VFDs), three 335 kW vane-axial surface intake fans with VFDs, 21 automated airflow regulators, six automated dampers, seven automatic doors and 198 underground auxiliary fans with ON/OFF starters. Additionally, the system monitors airflow at 48 locations, carbon monoxide (CO) at 40 locations, nitrogen dioxide (NO2) at 21 locations, and dry bulb and wet bulb temperature at 21 locations. The VOD system is also integrated with a tagging and tracking system to modulate the ventilation system automatically and in real time according to the presence and position of the personnel and vehicles. The tracking system comprises of 75 vehicle tags with diesel status and hydraulic status (ON or OFF), 440 personnel tags, and 200 tracking zones. Finally, it also involves the configuration and updating of 55 level plan and interactive procedures and 24 daily scheduled events. NRS currently uses VentSim™ CONTROL, Ekahau Tracking and PI Datalink to control, monitor, and configure their VOD system."

Jan 1, 2019

By J. Shanks

In 1920 the writer presented some notes, embodying his experience with storage-battery locomotives as main under-ground haulage-motors at Brazeau collieries. (1) Since that date these motors have stood up well to the test of maximum output and heavy overloads, having accomplished all that was expected of them. The notes presented in 1920 gave a brief description of the conditions under which these motors were working at Brazeau collieries, also the cost, per ton mile, of operating them. The cost per ton mile has since then been appreciably reduced, by working the locomotives nearly to capacity and under more ideal haulage conditions, on both shifts. It is not the intention of the writer to repeat what was written in 1920, but rather to give members the benefit of his experience in operating different types or designs of locomotives; to draw their attention to the drawbacks of some designs, and to the improvements made in some of the more recent storage-battery locomotives put on the market, as regards efficiency, upkeep, and safety. Because of their flexibility storage-battery locomotives have advantages over any other type of haulage, where grades are suitable to their use. The number in use in the mines in the United States has increased enormously during the past few years, and this method of haulage is, at the present time, attracting the attention of British and Continental mining engineers.

Jan 1, 1924

By Stephen B. Cheeseman

The quantity of data available and the rate at which we access such data are rapidly increasing. Electronic data capture systems, fleet management systems and a host of other technological advancements have created a constant stream of real-time, tactical data. However, are we taking advantage of this data? Are we converting data into useful information to aid in efficient decision-making? Mining operations are struggling with ?information overload?, finding it difficult to extract the benefits from vast stores of data. Without the necessary tools to facilitate a data filtering and information reporting process, most operations revert to old practises such as re-entering data into multiple spreadsheet reports. As a result, the ability to make effective use of data still eludes many mining operations. Some operations have taken audacious steps to rectify this situation. The De Beers Venetia mine in South Africa has implemented an integrated mining information technology solution that transforms their data into practical, usable information allowing staff and management to make decisions that improve efficiencies and reduce costs. In the absence of quantitative justification or ROI, De Beers took a risk in implementing change. Today, they are realising the benefits. This paper will unearth the information technology issues that surfaced during the Venetia implementation, then identify the benefits De Beers has obtained from deploying an integrated mining information technology solution at the Venetia mine.

May 1, 2002