Search Documents

"The ore currently being milled at Delnite is a high pyrrhotite ore with the gold intimately associated with the pyrrhotite. To get maximum recovery of the gold with the lowest reagent cost, it is necessary to keep the pH as low as possible In the laboratory the best results were obtained with a pH of 10 but in the plant it was found that a pH of 11 was the minimum practical pH. With the n1anual control it was difficult to maintain this figure.The Mines Branch had a conductivity probe (see Fig. 1), developed by Dr. G .G. Eichholz that they wished to try out in plant operation.On June 17, 1963, the probe with all necessary control equipment was installed in the regrind circuit (see Fig. 2) at Delnite Mines. Crushed quick lime is fed at this point but it is also necessary to feed hydrated li1ne at two other points in the cyanide circuit in order to maintain the pH close to 11. 0 throughout the circuit. Only the feeding of the quick lime at the regrind mill was controlled in this test.One thing that concerned me with the operation of the probe was whether the reading on the probe chart would correspond to the pH. A look at the graph accompanying this paper will show that except for very minor variations the graphs of the chart reading and the pH reading are parallel. The upper graph shows that the pH reading and the lime titrations also correspond and that the cyanide titrations appear to have little effect on the pH reading.Table 1 gives the results obtained for the two months before and after the instal1ation of automatic control as well as the two months of control. Unfortunately there was a decided change in ore just after the automatic controls were removed. There was much less pyrrhotitc in the ore than usual thus changing the need for lime and cyanide."

Jan 1, 1964

By J. Drozdiak

In this paper we present the results of preliminary investigations into the applicability of new laboratory scale tests for the prediction of operating gap and specific throughput in high pressure grinding rolls (HPGR). The work is a part of the CAMIRO HPGR research program being conducted at the University of British Columbia, which aims to develop a suite of small-scale tests and procedures for the selection and sizing of HPGRs. A focus of the presented study is to test sample types in terms of their terra-mechanics based characteristics and relate them to specific throughput and gap results from pilot HPGR testing on the same samples.

Jan 1, 2012

By Hans Lundberg

During the last few years, geophysical methods have been introduced to aid mining geologists and mining engineers in locating mineral deposits. These methods have been developed as the result of investigations of various physical characters of minerals and rocks. In prospecting for ore-bodies, electrical methods have proved most successful. These methods are based on the great differences in electrical properties, and especially in conductivity, between ore minerals and rock minerals. The electrical resistance of the common minerals, rocks, and ores in ohms per cubic céntimeter is given in the following table: [ ] The first attempts at electrical prospecting were based on observing currents of polarization around certain ore bodies, which currents it was possible to measure. This method has been developed by Prof. Schlumberger and has been utilized by him successfully. He is represented on this continent by Mr. Sherwin Kelly, who has successfully operated the method here.

Jan 1, 1926

By S. Banisi, A. R. Hasankhoei, Gh. Parsapour, A. R. Ghasemi

At the Gol-E-Gohar mining and industrial Company, a pelletizing plant, which includes two parallel dry closed grinding circuits and a pellet production circuit, produces 600 t/h. Each grinding circuit consists of a burner, a dry ball mill (6 m×13 m) and an air separator. Each ball mill consists of a 2 m-long dryer chamber and an 11 m-long grinding chamber. Iron ore concentrate is fed to the drying chamber to decrease its moisture from 2.5% to below 0.2%. The drying chamber consists of 56 flights in two rows. It was found when the feed moisture content decreased from 1.3 to 3.5%, the throughput decreased by 14% (40 t/h) indicating a low performance of the dryer. In order to improve the efficiency of the drying section, a scale down version of the dryer was constructed in a 1m diameter mill with a transparent end to make image analysis possible. It was found that because of the inappropriate veiling profile in the drying section, most of materials are not subjected to the hot gas tunnel. To overcome this problem, various flights with different geometries were physically tested and also simulated by the KMPCDEM © software. With the aim of arriving at a proper veiling profile which maximizes the particles contact with hot air, a new flight design was obtained and tested. The installation of the rectangular tooth type flights in one of the mills in the plant made the comparison of the old and new designs possible. The evaluation of the designs in a period of three months indicated 15 t/h increase in the throughput in the case of the new flight design.

Jan 1, 2016

By Irvine J. Berscheid

This paper describes a rock drill bit which, although conventional in the processes of manufacture and use on the job, has incorporated into the outer wall or periphery of the insert, where wear is always the greatest, a variable amount of extra metal, distributed in units of height of insert to withstand this excessive wear. Explained are variations of construction, how the extra metal enables the bit to drill more footage, prevent antitaper and the need to gauge grind, increase penetration rate and the length of run per regrind, reduce shank breakage and ma-chine costs, and permit increased production per man-shift, without requiring any change in equipment already on the job. F OR purposes of clarity, reference to bits here means integral rods or multi-winged bits which have their inserts sharpened to a conventional shape. When dull, the insert has worn, on its face, a flat which increases in width as we progress from near the center of the bit toward the outer edge. Very

Jan 1, 1965

"Virtual reality, a 3D computer-generated environment, has become a recognized delivery system for many forms of education. This paper describes the application of virtual reality to mineral processing education. An interactive mineral processing visualization module developed at the University of New South Wales, Australia, provides users with an overview of a base-metal concentrator and details about how the mined ore progresses through stages in processing. The module also involves developing instructional based plant layouts and flowsheets in the virtual environment. These assist the user in understanding the essential components of the base-metal concentrator.RÉSUMÉ La réalité virtuelle (RV), un environnement en 3D généré par ordinateur, est devenue un système de prestation reconnu pour diverses formes d’éducation. Cet article décrit l’application de la réalité virtuelle à l’éducation dans le domaine de la minéralurgie. Un module interactif de visualisation du traitement des minerais développé par l’université de Nouvelle-Galles du Sud, en Australie, offre aux utilisateurs une vision d’ensemble d’un concentrateur de métaux communs ainsi que des détails concernant la progression du minerai extrait à travers les différentes étapes de traitement. Ce module implique également le développement de schémas de réalisation et de traitement didactiques dans l’environnement virtuel, lesquels schémas aident les utilisateurs à appréhender les composantes essentielles d’un concentrateur de métaux communsINTRODUCTIONVirtual reality (VR) is the creation of an artificial environment that is experienced through sights and sounds provided by a computer (Squelch, 2001). The simulated environment is achieved through technologies such as 3D graphics, audio feedback, and special peripheral devices to produce interactive environments.Virtual reality has been used in diverse fields including medicine (Riener & Harder, 2012), entertainment (Hsu, 2011), military (Manojlovich, Prasithsangaree, Hughes, Chen, & Lewis, 2003), manufacturing (Zimmermann, 2008; Jiang, 2011), and chemical processing (Squires, Andersen, Reklaitis, Jayakumar, & Carmichael, 1992; Schofield, Lester, & Wilson, 2005). Virtual reality is also becoming the recognized delivery system for education in many fields, including engineering (Bell & Fogler, 1996, 1998; Shin, 2002). For example, VR laboratories have been designed and developed to teach users fundamental features of heterogeneous catalytic mechanisms and absorption columns (Bell & Fogler, 1995), the multi-phase and multi-component blast furnace iron-making process (Babich & Senk, 2009), and to guide users to identify various safety measures while working in a real laboratory (Bell & Fogler, 1996)."

Jan 1, 2017

By Chelto. D. Smith

With the pressure on mine and metallurgical managers to take accountability for responsible corporate governance in their operational area, it is no longer acceptable to rely on central departments in the organization to manage safety, health and environmental impacts of the company?s processes. Environmental impacts exist because of the production or mining process. Some of the inputs to the process are natural resources and some of the outputs of the process are the inputs to the environmental control equipment, plant and the environment itself. Environmental management therefore needs to be incorporated in production management to effectively control and reduce the impacts. Many aspects of environmental management are identical to production management and the systems to manage them will likewise be very similar. By examining key components of these two management systems a decision can be made whether environmental management and production management are structurally similar and can be integrated into a combined IT solution.

May 1, 2009

By Alexander Smith

"The three principal known mineral deposits of the Taku River area lie in the Tulsequah synclinorium. The axis of this north-south trending structure is along Tulsequah River valley; about 6 miles east of the eastern contact of the Coast Range batholith.The one proven mine of the area, the Polaris-Taku, is on the west side of the valley. It is a gold property, the gold occurring in fine needles of arsenopyrite disseminated in carbonatized volcanics. The mine was originally called the Whitewater, and the adjacent area the Whitewater gold belt. During the years 1937 to 1942 gold having a value of $3,284,000 was produced from 313,500 tons of ore milled."

Jan 1, 1954

By G. F. Trainor

At the Canadian Natural Resources Limited (CNRL) Horizon Mine they use Wenco International Mining Systems Ltd (Wenco) Fleet Management System to monitor and control their production fleet with the goal of increasing operator productivity and safety, and raising dispatcher awareness and control. Amongst the broad productivity goals CNRL wanted to achieve with help from the system was a very specific need to blend ore at the truck level. CNRL uses 25m x 25m block geological model information to represent their complex ore body. Wenco's High Precision GPS application, BenchManager provides precise graphical actual-vs-design operator feedback and system integration. Together the two companies advanced the BenchManager product to meet CNRL's needs by using live camera feeds to compare activity with data collection that ultimately lead to changes in the algorithm to include enhanced GPS indicators and the support of a GLONASS assisted solution generating distance and bearing information.

May 1, 2011

By E. Pallumbo, N. Szwedska, R. Asselin

"This paper highlights the results of collaboration between geology, mining and mineral processing teams during the restart of the North American Lithium Project, located near La Corne, Quebec, Canada. This collaboration was central in ensuring a cross discipline harmonization of design parameters and key inputs, all of which allowed for the development of an optimized life of mine plan suited to the particular needs of the operation.INTRODUCTION In July 2016, North American Lithium Inc. (NAL) began the process of restarting operations at the former Quebec Lithium Mine, located in the municipality of La Corne, Quebec, Canada. The North American Lithium Project (the Project) as it is known today, is the latest chapter in the history of this property. In order to provide a robust foundation for the project, multidisciplinary collaboration was instituted between the geology, mining and metallurgy teams. Despite the intrinsic link between these departments, in many instances their work is completed separate from one another; in silos. This collaboration highlighted specific drivers in the mining value chain that could be exploited to ensure that a saleable product could be produced effectively. This paper explores some of the concepts and strategies that were developed during the feasibility study that supported the project restart (excerpts from the study technical report have been used throughout this paper). PROJECT HISTORY In 1942, prospectors identified the presence of numerous spodumene-bearing pegmatite dykes on the Property. This led to additional interest and exploration drilling campaigns. In 1955, Quebec Lithium Corp. (QLC), who had acquired the property, began construction of an underground mine with mill facilities located on the surface. Operations began the following year at a production rate of 1,100 tonnes per day. A historical cross-section view of the underground mine is shown in Figure 1. In 1959, QLC began the construction of an on-site lithium refinery to produce lithium hydroxide. The refinery was finally operational by 1963. Mining and processing operations continued until 1966 when activities were halted due to a labour dispute. The property was sold and a few years later attempts to resume production were unsuccessful. Property ownership changed several times again until being acquired by Cambior in 1987. In the early 1990’s the existing mine and mill facilities were sold and the mine site rehabilitated"

Jan 1, 2019

By M. R. P. Snow

"This paper outlines geotechnical conditions that commonly exist in underground, hardrock mines and the challenges posed for ground-support steel, specifically rockbolts, used in these environments. A model is proposed whereby the in-situ stress and rock-mass classifications (based on Bieniawski’s rock mass rating) form the basis of determining the desired steel properties of the rockbolts used. Based on the ASTM F432 bolting specification, recommended minimum steel properties are defined for three ranges of in-situ stress levels, each with their own six ranges of RMR values. Heat treatment for the steel can be specified once these minimum steel properties are known.RÉSUMÉ Le présent article décrit les conditions géotechniques qui existent fréquemment dans les mines souterraines de roches dures et les défis que cela pose pour le soutien de terrain en acier, plus spécifiquement les boulons d’ancrage utilisés dans ces environnements. Un modèle est proposé dans lequel les contraintes in situ et les classifications de la masse rocheuse (selon la classification de la masse rocheuse de Bieniawski) servent de base pour la détermination des propriétés désirées pour l’acier des boulons d’ancrage utilisés. En se basant sur les spécifications de boulonnage de l’ASTM F432, les propriétés minimales recommandées pour l’acier sont définies pour trois plages de niveaux de contraintes in situ, chacune avec sa propre plage de six valeurs de classification de la masse rocheuse (RMR). Un traitement thermique pour l’acier peut être spécifié une fois que ces propriétés minimales pour l’acier sont connues."

Jan 1, 2016

By A. I. A. Salama, M. W. Mikhail

"A comprehensive software package has been developed at the Western Research Centre to meet many of the coal preparation requirements in the Canadian coal industry. This package performs three main functions: (1) data handling and manipulation; (2) data analysis, including the generation of washability data, performance evaluation and prediction, density and size modelling, evaluation of density and size partition characteristics, and attrition curves; and (3) graphics output.The software described in this paper is potentially a valuable tool for coal preparation plant engineers and operators for evaluating process performance and adjusting plant density separator cutpoints. Moreover, the analytical laboratory technician could find this package very useful in manipulating and presenting laboratory results."

Jan 1, 1997

By Ming’an Wei, Qifu Duan, Chengtie Wang, Jianmin Wu, Erdenet Mining Corporation, Lusheng Zhou, Wenjian Wu

"The development and industrial applications of magnetic liners have been around for decades. A Swedish company SKEGA first introduced the rubber magnetic liner, and then followed by the Chinese metal magnetic liners. Traditionally, both liners were used in secondary and regrind ball mills, especially for ores containing magnetic materials. Mostly steel balls or equivalent forged balls, usually below 60 mm in diameter, were used as grinding media. With the development of mineral resources over the years, SAG mills and larger ball mills have become the dominating components for comminution circuit design globally. Due to the larger ball mills and thus larger grinding balls (up to 80 mm) especially in non-ferrous metal industry, the application of magnetic liners has been very limited. Based on the new development of materials, the HMR Group Limited has been exploring new designs of magnetic liners which led to the invention of the Nano Steel Magnetic Liner (NSML). Recently, NSML had a successful application in a 5.5m x 6.5m ball mill with 80 mm balls at the Erdenet Copper Mine in Mongolia. Although the first set of liner had a service life of 12 months, the design of the second set was modified and improved to accommodate the operating conditions, which is expected to reach least 24 months service life. The original manganese steel liner only had about 8 months liner life.1. IntroductionMineral processing is an essential operation for the development and utilization of mineral resources. The effective concentration of various useful minerals depends on sufficient liberation of the mineral particles in the ore. The crushing and grinding process such as ball milling are the most common way to achieve proper liberation size. Mill liner is an eternal topic for the operations, not only because it protects the equipment, but also affects the mill grinding efficiency and availability. In recent years, magnetic mill liners have been developed that can easily meet the production targets with numerous benefits, such as zero maintenance, reducing specific energy consumption and improving grinding efficiency."

Jan 1, 2016

By Cheng-Ting Chiang

Information integration and exchange for the entire building life cycle is one of the most important issues in the AEC industry. Although the Building Information Model (BIM) technology is widely utilized to address them, BIM is mainly concerned within the design and construction (D&C) phases. In the operation and maintenance (O&M) phases, however, the information integration and exchange issue becomes more complicated because software applications here require not only BIM but other information outside of the AEC domain, e.g., disaster mitigation. Nowadays, most BIM-related research focuses on the D&C phases and pays less concern on the O&M phases, hence there is a research need that can help seamlessly transfer the information between the D&C and O&M phases. In this research, a software framework using ontology was designed to deal with aforementioned problems. The BIM data from the D&C phases were used as a foundation to generate new models for different software applications for the O&M phases. The ontology technique was employed to assist the model transformation process between the original BIM and the models for applications. Finally, a disaster mitigation example was chosen to validate the framework, in order to make sure that the transformation process is comprehensive and useful from domain experts? perspective.

Aug 1, 2013

By Bob Rappolt

Discussion Points Part 1: Global Mining Industry/Related Issues ? Historical Metal Price Trends. ? Historical LME Metal Stockpiles. ? China?s Demand for Metal. ? World Population Growth, Demands and Development. Discussion Points (cont?d) Part 2: Canadian Mining Industry ? Where are we? And where are we going? ? What progress have we made in the past 20 years regarding: ? Safety -Employee Levels ? Labour -Relative Compensation ? Productivity - Technological Advance ? Where do we stand regarding mineral production? ? What does the future hold for us?

Apr 1, 2005

By Roy T. Bowles

This paper focusses on technological developments which occurred in the village of Deloro, Ontario between 1868 and 1919. These developments illustrate the manner in which improved metallurgical processes linked Ontario mineral resources to industrial expansion. Overview of Deloro The village of Deloro is in Hastings county, about 5 miles from the village of Marmora, the site of the old Marmora iron works and the more recent Marmoraton iron mine. In this area, the Canadian Shield meets the Great Lakes lowlands. The first settlement in the vicinity occurred in the 1820s and was associated with the Marmora iron works. Settlement grew around agriculture. Gold was discovered in Hastings county in 1868. Deloro - the name derives from gold - developed as a concentrated settlement in proximity to several gold mines and the related processing activities. By 1901, substantial smelting works were successfully producing gold and arsenic from local ores. The village was developing as a company town within the framework of benevolent paternalism. For reasons associated with markets and with local ore supplies, the Deloro mills were idle for a period beginning in 1902. Developments in later periods connected Deloro to world events. In 1903, silver was discovered at Cobalt, Ontario. By 1907, M.J. O'Brien, who owned mines at Cobalt, had purchased the Deloro works and was using them to process Cobalt-area ores*.

Jan 1, 1999

By K. G. Chipman

The Geological Survey is the oldest map making department in the Canadian Government service, and when organized in 1842, one of the first principles to be recognized was the absolute necessity of having good maps. The primary purpose of the Survey has always been geology; but because a graphic representation by means of maps makes the written report .more readily intelligible; because the correlation of known geological facts is often difficult or nearly impossible unless they can be represented on a map; and, because the public demand information shown in this way, the Geological Survey must continue to supply maps; and the supplying of these maps must be considered as an essential part of the work of the Survey. It is a commonly recognized principle of pedagogics that an appeal to the eye is quicker than one to the ear; that children (and others) learn more quickly when a thing is presented to them through the eye rather than through the ear. The application of this principle to the work of the Geological Survey is that, to a large number of people, the message of a map is more quickly grasped, is more readily intelligible, and is in many ways of more interest and value than is the same information in a report. I do not mean that the maps are of more importance than the reports.

Jan 1, 1924

By K. Iturralde

The topic of this article is the automation and robotization in refurbishment processes of industrial buildings. The need to mold these production spaces is quite universal. Particularly in the regions with a high industrial development and with a lack of buildable land, there is a need to convert this kind of spaces into an improved production system. The latest developments can be a useful tool for achieving a more efficient way of reforming this type of construction. On the one hand we have the digital or computerized 3D Laser Scanning (Computer Aided Measurement) that allows an accurate 3D modeling of the entire building. On the other hand, the project management using BIM (Building Information Modeling) could provide an easy design of each of the elements of the refurbishment. Finally, through the production of construction elements using robotics as jig or for CNC (Computer Numerical Control) we achieve a neat production of each element. How can be all those technologies applied in the refurbishment or expansion of industrial buildings? The research takes a first approach and analyzes industrial buildings that can be called generic or not specialized. To narrow the field of refurbishment, three major factors are defined. The first is to minimize the bill of the energy consumption of the buildings. This could be done either insulating the envelope, reducing the waste-volume to be conditioned climatically or creating facilities for energy production. The second is that the refurbishment or expansion of industrial buildings should try not to interfere on the production process that takes place in the building. In other words, the assembly of the elements in the construction site should be quick and easy, causing the least of disturbance at the workplace. Finally, the research makes an approach towards a robot integrated industrial or productive building .

Aug 1, 2013

By P. Mageau-Béland, È. -M. Proulx, M. -C. Patoine

Over the past six decades, Hatch has helped several industrial processing facilities in debottlenecking their operations, allowing them to produce more with the same equipment, to reduce and even eliminate expenditure investments, or to increase the return value of their expansion projects. These successes result from the application of a proven analysis approach that can be applied to any industrial facility. A five-stage methodology is discussed and demonstrated with a specific example of a nickel concentrator optimization study. The first stage is an observation stage which allows to meet key actors at the plant, develop mutual understanding of problems, understand operating philosophy, and efficiently collect large amounts of operating and maintenance data. Following is a data compilation stage during which data is analyzed over a representative time period to identify parameters that significantly affect the production, to evaluate data reliability and to define the focus of the upcoming analysis. Quantitative metrics are defined using statistical tools such as pivot tables, histograms, percentiles and MDR (Maximum demonstrated production rate during 3 to 7 consecutive days). Then, the production bottlenecks are identified by a thorough analysis of the facility’s control philosophy, process throughput, equipment capacity, availability, downtime causes, and interaction between components of each circuit. Understanding the maintenance practices and frequency of planned shutdown is also critical to this analysis. Opportunities for improvement are identified in collaboration with the operation, maintenance and engineering teams, ranked as a function of their impact on the bottlenecks and prioritized. The final and most critical stage involves engagement with the plant stakeholders, namely the operators and the maintenance staff members, to present the results of the analysis and obtain their participation in the implementation of the solutions. The benefits of the case study translated into: 10% production capacity gain, improved maintenance planning and avoidance of several million dollars of investment.

Jan 1, 2016

By M. R. Shadnam

This contribution provides an assessment of research and development efforts to optimize SOx, NOx and mercury capture in flue gas. Coa, characteristics and combustion conditions in a power plant have an impact on the types and concentration of flue gas pollutants. These factors can also affect the amount of pollutant removed. This contribution would also provide a comparative study of the technologies that holistically aim remova, of SOx, NOx and mercury altogether in coal-fired power plants. A portion of this contribution provides background information on regulatory drivers.

Jan 1, 2010