Search Documents

By J. Kicki

The paper depicts the current status of the EKSPERT mining machinery management system and shows the prospects for its further development. The system is the result of a rare attempt to utilize the comprehensive dataset; this refers to a precisely identified group of users and is used to develop a solution with a scope that encompasses other areas of activity within the company. The authors present the incredible flexibility and usefulness of the system used at KGHM Polska Miedz S.A. for everyday control of the mining machinery fleet. The issue of visual aspects of the reports generated by the system is handled separately and used as a tool allowing for implementation of the methodological assumptions of EKSPERT. A concept for creating a system for assisting decision making in the process of mine management with the use of IT tools and production monitoring is also discussed. The solution is based on integration of information from both the monitoring field and visualization of the technological process around the Production Reporting Center.

Aug 1, 2013

By Abdelhak Bentriou

The choice of tool for the first well of an oilfield or gasfield is an important factor, given that we will be drilling with the same type of tool for the entire phase and explains why we need to have another type for comparison based on the efficiency of the tool and its ability to crush the rock, and the wear of different types of tools. Development of theoretical and practical tests to determine the optimal regime for drilling is required to take into account the characteristics of rock layers crossed. Classification of boring tools is based on the geometry of the teeth and depends on the hardness, the abrasiveness of rocks as well as their hydraulic system, but it is better to classify them according to the working conditions with a coefficient designating a discriminant. This is called physical characteristic of the drilling tool. The goal is to designate each element of the tool by a coefficient. Results were obtained from laboratory tests. Modeling the initial rate of progress by different types of tools allowed us to determine an adequate mathematical model of the speed initial progress in clean conditions. Using experimental data and statistics we have established the mathematical model of the average speed of progress as a function of time. With these equations we can determine the wear evaluation and analysis of these factors as an approach to classification according to their characteristics. The main equations for the selection of drilling tools will be based on the optimization of drilling parameters for each type of tool. After analysis, we choose the tool that gives a better forward speed with an optimal load and axial rotation.

Aug 1, 2013

By Masatsugu Morimitsu

This paper introduces new technology of oxygen evolution anodes which can be applied to produce copper, zinc, cobalt, and other metals by electrowinning. The anode consists of nano iridium oxide particles dispersed in amorphous tantalum oxide matrix as a catalytic layer formed on a titanium substrate. The anode can reduce oxygen evolution potential by 0.25 to 0.55 V compared to commercially available lead alloy anodes and can suppress unwanted side reactions such as manganese oxyhydroxide, lead oxide, cobalt oxyhydroxide which occur during oxygen evolution in the electrowinning solutions. This technology is effective for environmentally friendly electrowinning processes with low energy consumption and less anodic deposition.

Jan 1, 2011

By Ahmad Abdollahi

Many factors affect mechanical properties of hypoeutectic Al-Si alloys. As examples the presence of impurities such as Mn and Fe due to the formation of intermetallic phases, additions of small amounts of alkaline earth metals and cooling rate in consideration of Si formation, they all have an impact on mechanical properties of hypoeutectic Al-Si alloys. In this investigation, the effect of Fe content into the specification range of A357 alloy, the addition of different modifiers consisting of Na, Sr and Ca for the alloy of A356 and different mounting techniques for separately cast test coupons of hypoeutectic Al-Si alloys using the lost wax method were studied. The results showed that using material with lower Fe content and addition of modifiers improve mechanical properties. Also different mounting techniques resulted in different mechanical properties.

Jan 1, 2004

By John Oxenford

There are currently two operators producing oil from the surface-mineable portions of Alberta?s oil sands (Syncrude Canada Ltd. and Suncor Inc.) and two other companies are proposing to enter the industry (Albian Sands in 2002 and True North in 2004). Tailings from the two current oil sands plants contain approximately 220 000 tonnes per year of recoverable TiO2 and approximately 80 000 tonnes per year of recoverable zircon. This represents approximately 6% of the world?s TiO 2 consumption and approximately 9% of the world?s zircon production. With the commissioning of plants by Albian Sands and True North, and the announced expansion of plants by Syncrude and Suncor, it is expected that these tonnages could quadruple in the next ten years. All of these operators have at least 50 years of reserves even at these expanded production rates. The occurrence of heavy minerals in Alberta?s oil sands has long been known and is well documented in the literature. There have been a number of attempts to produce market-grade products from this resource and the results of this work have been quite mixed. Typically, researchers have used the normal mineral dressing techniques of the industry and have found the mineral assemblage does not respond to these techniques all that well. This has led to the widelyheld suspicion that there must be some difficult metallurgical problems associated with this resource. There are three main problem areas that have created difficulties for previous researchers: 1) The bitumen coating on the sand grains; 2) Secondary mineralization such as pyrite, siderite and calcite 3) A high proportion of aluminosilicates (approximately 25%) that have the same gravity, electrostatic and magnetic properties as other minerals in the heavy mineral suite. Recent work by Lakefield Research shows that these problems can be largely overcome with some novel approaches. The bitumen can be removed by washing with a solvent in the presence of a demulsifier. The pyrite can be removed by flotation. And the titanium and zircon minerals can be separated by selective flotation followed by conventional electrostatic and magnetic separation.

May 1, 2001

By T. G. Joseph

ABSTRACT: The Canadian oil sands provide some of the harshest mining conditions in the world. Asoperations demand ever bigger tools, the toll on large mobile mining equipment is high, with structurallife often half of that expected. Soft ground conditions predominantly lead to fatigue failure scenarios, poor stability, and inconsistent payload evaluations. These challenges are not solely a concern for Canadian oil sands mines; there are far-reaching implications for surface mining equipment in any poor ground-operating environment. This paper focuses on the basics of payload evaluation, motion response and a simple estimate of structural life for haulers.

Jan 1, 2011

By R. E. Whitehead

"Abstract - Biotite from aplite that appears to have crystallized simultaneously with disseminated Cu-Mo mineralization at MacLeod Lake in northern Quebec yields K-Ar dates in the range 2032 ± 44 Ma to 2097 ± 47 Ma. The mean value, 2065 Ma, is some 400 Ma younger than the 2485 ± 64 Ma date obtained from a hornblende concentrate separated from a granodiorite sill that is spatially, but apparently not genetically, associated with the disseminated Cu-Mo deposit. The mean biotite date of 2065 Ma at MacLeod Lake, a K-Ar date of 2055 Ma reported from an area 50 km east of MacLeod Lake and published dates of about 2000 Ma for galenas from the Chibougamau Cu-Au ores, suggest a widespread thermal and mineralization event, in that part of the Superior Province east of James Bay, that differs from the common late Archean mineralization that is related to volcanism and metamorphic-intrusive activity.Sommaire - Les datations au K-Ar sur des biotites qui auraient cristallise en même temps que la minéralisation disséminée en Cu et Mo dans une aplite mise en place au Lac MacLeod, au nord du Québec, s'échelonnent entre 2032 ± 44 Ma et 2097 ± 47 Ma. La datation moyenne, soit 2065 Ma, est d'environ 400 Ma plus récente que la datation obtenue pour un concentre de hornblende extrait d'un filon-couche de granodiorite qui est spatialement mais ne serait pas génétiquement associée à la minéralisation disséminée en Cu et Mo. La datation moyenne de la minéralisation au Lac MacLeod, soit 2065 Ma, la dataion au K-Ar à 2055 Ma citée pour une région à 50 km à l'est du Lac MacLeod, de même que les datations d'environ 2000 Ma établies pour des galènes qui se trouvent dans le minerai aurifère et cuprifère à Chibougamau, suggèrent un phénomène thermique répandu qui aurait produit la minéralisation dans cette région à l'est de la Baie James, dans la province du lac Supérieur. Ce phénomène serait diffèrent de celui qui aurait produit la minéralisation répandue d’âge archéen tardif qui elle serait associée à l’activité volcanique et à l‘activité intrusive accompagnée de métamorphisme."

Jan 1, 1992

By T. G. Joseph

ABSTRACT: The Canadian oil sands provide some of the harshest mining conditions in the world. Asoperations demand ever bigger tools, the toll on large mobile mining equipment is high, with structural life often half of that expected. Soft ground conditions predominantly lead to fatigue failure scenarios, poor stability, and inconsistent payload evaluations. These challenges are not solely a concern for Canadian oil sands mines; there are far-reaching implications for surface mining equipment in any poor ground-operating environment. This paper focuses on the basics of payload evaluation, motion response, and a simple estimate of structural life for haulers.

Jan 1, 2011

By Neil Westoll

Extensive Global Network ?Working together, AECOM provides clients with a unique blend of global reach, local knowledge, innovation and technical excellence. ?43,000+ team members worldwide ?450+ offices ?100+ countries ?6 continents The Changing Climate ?Climate change is ?official??IPCC 2007 ?Climate change will create instability, change and opportunities ?Companies that are resilient and adapt will survive and evolve ?CO2/GHG emissions will be curbed by legislation ?How will this affect the mining industry? ?How can the mining industry adapt to the new realities?

May 1, 2009

By J. Marks

The measurement of greenhouse gas (GHG) emissions from primary aluminium production and inventory of these emissions of carbon dioxide and PF Cs have become an important issue for primary aluminium producers. Most global producers have either voluntary emission goals or emissions limits established through national regulatory requirements. International good practices for inventory of these emissions for national governments are established through the Intergovernmental Panel on Climate Change (IPCC). The current good practices, last updated in 2000, are being revised and are expected to be adopted by governments in the spring of 2006. There are a number of changes expected in the guidance that will impact how facilities account for their GHG emissions. This paper describes the changes to the guidance and the implications of these changes for aluminium producers.

Jan 1, 2006

By T. E. Newkirk

In the past few years there has been considerable controversy on the most suitable material to be used in ventilation doors which will have to serve also as fire doors. For this reason it was thought useful at Mclntyre to find out to what extent our zinc chloride treated spruce doors were fire resistant and what protection we could expect in case of an underground fire. The doors to be tested were constructed of the same material as that used in our regular ventilation doors underground, namely, 2-inch tongue-and-groove well seasoned spuce. It is to be noted, however, that whereas the dimensions of the ventilation doors are 5 ft. by 6 ft., those of the test doors were only 14 in. by 17½ in. The treated doors were made up from lumber that l1ad been treated with chromated zinc chloride, as described in Mr. Keeley's paper. Two kinds of tests were carried out: a heat test and a flame test. An electric muffle furnace for assaying, equipped with a pyrometer, was used for the beat test, the furnace door being replaced by the wooden door to be tested. In the flame test, the door to be tested formed one end of a rectangular steel box in which was placed a large blow-torch. Air was admitted at the rear of the box. A pyrometer recorded the temperature at the inside surface of the door where flame impinged. The results of the tests are presented in the accompanying table, in which the word 'failed' is to be interpreted as meaning that the door had been damaged to the extent that smoke, but not necessarily flame, issued from its outside surface.

Jan 1, 1949

By Hani S. Mitri

Strainbursts in brittle rock are common to deep underground mines. The state of stress at the boundary of mine openings is dictated by a biaxial stress/loading condition. This paper reports the results of a series of biaxial compression tests carried out on 100 mm cubic samples of norite rock, under different horizontal-to-vertical stress ratios. The results indicate that the biaxial compressive strength is considerably higher than the uniaxial one. It is found that the norite sample behaviour under biaxial loading mirrors field behaviour where shearing and progressive spalling of the opening boundary are observed prior to strainbursting. Sample failure is initiated by rock spalling at the sample free faces, i.e. in the plane of biaxial loading. Finally, it?s the out-of-plane shear failure mechanism that causes the sample to collapse. Shear failure takes place violently and abruptly and is accompanied with considerable audible noise.

Apr 1, 2005

By J. W. Stickney

"On July 1, 1977 Hudson Bay Mining and Smelting Company Limited announced the commencement of construction of a 3800 ton per day concentrator at Snow Lake, Manitoba. Snow Lake, a community of 2200 people, is located 130 road miles from the main metallurgical plants at Flin Flon.The design, detailed engineering and equipment selection for the project was awarded to Wright Engineers Limited of Vancouver, B.C., who would be working in close liason with Hudson Bay Mining personnel throughout the project.The feasibility of constructing a metallurgical plant in the Snow Lake area, in addition to the concentrator at Flin Flon, had been under study since 1964 with plants of varying capacities and designs being considered. Each successive study recommended a plant of increased capacity and sophistication and finally upon an in-depth study in 1976 of ore reserves, freight rates and operational benefits, the construction of a 3800 ton per day copper-lead-zinc concentrator appeared highly benificial."

Jan 1, 1981

By H. Yasuhara, N. Kinoshita, S. Nakashima, K. Kishida

"In this study, flow-through experiments in fractured rocks have been conducted under different stress, temperature, and pH conditions so as to understand the evolution of permeability induced by these conditions. Throughout the experiments, the confining pressures and temperatures are well-controlled. Effluent concentrations are also measured for the ten elements of Si, Al, K, Fe, Ca, Na, Mg, Ti, S, and Cl that are included mainly in the targeted rocks. In the early stage of the experiments, the fracture permeability measured abruptly decreases with time, and subsequently reaches quasi-steady state within a relatively short period. In contrast, the permeability in the intact rocks monotonically increases with time. The permeability increase and decrease are attributed likely to the relative dominance of mineral dissolution in the pore spaces and to that of mineral dissolution/crushing at the propping asperities within the fracture and/or mineral precipitation onto the free surfaces, respectively. The evolving rates and magnitudes of the permeability are likely to be controlled by the stress exerted over the contacting asperities, temperatures, and pH of the permeant. Thus, this complicated behavior should be attributed to the coupled chemically- and mechanically-induced effects, which should be examined in more detail for longer period to contribute to the safe entombment of radioactive wastes. INTRODUCTIONUnderstanding of the flow and transport characteristics of porous/fractured rocks is required for the safe and long-term geological isolation of energy-related by-products (i.e., high level radioactive wastes and anthropogenic CO2). Notably, under relatively high temperature and stress conditions, mechanically- and chemically-mediated processes may alter the pore structures in rocks, resulting in an irreversible evolution of the flow and transport behavior. Augmentation in permeability may result from mechanical dilation due to shearing and mineral dissolution within the pore spaces, while reduction may result from reversible or irreversible mechanical compaction, mineral dissolution at the contacting areas, and clogging of pore spaces by precipitation of secondary minerals."

Jan 1, 2015

By Asfahani. Jamal, Randa Mohamad

"Abstract - Electrical and structural characteristics of formations favorable for sulfur occurrences in northeast Syria are described using geo-electrical prospecting methods. Simple (VES) and combined (CVES) Schlumberger vertical electrical soundings and geo-electrical profiling using a Wenner configuration were applied to the Teshreen structure. Six profiles (A, B, C, D, E, and F) at the borders of anticlines, where positive and negative structures are joined and salt formations have a tendency to disappear, were studied.Secondary structures, characterized by high apparent resistivity exceeding 3000 Ohm.m were located on each profile using a Wenner profiling configuration. These secondary structures are demonstrated to be favorable for sulfur prospecting by both drilled wells and vertical electrical soundings. Traditional interpretation of the 84 VES measurments is supported by data from 14 CVES measurments. The CVES technique is a powerful tool, due to its improved resolution of the electrical boundaries.Thicknesses and resistivities of the Lower Al-Fares, Al-Garibeh, and Al-Dibbaneh formations were determined through the interpretation of VES measurments. The same VES measurments were then interpreted using the Pichgin method, whereby all the subsurface tectonic features were determined for depth penetration corresponding to AB/2 = 1000 m. The integration of the first and second VES phases creates a clear picture of the subsurface, including tectonic, geometric, and geoelectrical information. In summary, the sulfur occurrences in the research area are controlled by tectonic paths that are well defined by geo-electrical methods. These diverse geo-electrical methods could be used successfully for sulfur prospecting in similar environments."

Jan 1, 2002

Real Time Monitoring of Cemented Paste Backfill Introduction Methods ?how to instrument a Long Hole stope Key Results from 2 case studies: barricade pressures and displacement, in-stope pressures Importance of Real Time Monitoring How binder, rise rate, cement content affect fence pressures

May 1, 2010

By K. Thuro, H. Käsling, C. Wieser, G. Nuijten

"The time-dependent behavior of brittle rocks during stress relaxation is of great interest for mining industry, nuclear waste disposal as well as tunneling and underground construction. Several studies have shown that both elastic as well as inelastic deformation occur during stress relaxation (Emery, 1964; Zang & Berckhemer, 1989). While elastic strain occurs already during the drilling process, inelastic deformation is time-dependent and can endure for hours, days or weeks. To investigate the evolution of microcracks during core relaxation, two crystalline core samples were recovered from high in situ stress conditions in Europe’s deepest mine in Pyhäsalmi (Finland). Samples were prepared for testing within one hour after coring such that a large portion of the time-dependent component of relaxation could be recorded over several days using ultrasonic velocity as well as acoustic emission (AE) measurements.Results from AE analysis show an exponential decrease in the number of events over a period of several hours. Repeated sudden increases of acoustic events can be related to the propagation or the interaction of cracks. In the first hours of recording also the signal energies reached the highest values and the increases in signal energy correlate well with increased event rates. On additional drill cores, P-wave velocities were measured parallel and in 45° distances perpendicular to the core axis. After core recovery, stress-induced microcracking caused an exponential decrease in wave velocities similar to AE rates. Lowest compressional wave velocities were measured parallel to the core axis and thus normal to the foliation and in the direction of the maximum in situ stress component. The highest measured velocities occurred parallel to the foliation plane. Within the samples, the anisotropy ratios were up to 1.37 at the beginning of the measurements and increased to values of up to 1.8 after 45 days. The wave velocity anisotropy is in agreement with the in situ stress orientations."

Jan 1, 2015

By Robert P. Harrison, Marie-Christine Patoinel, Kristian E. Waters

This paper describes a collaboration between McGill University and Hatch Ltd. to expose undergraduate students to real-world industrial projects. As part of the final-year design course, the students receive a detailed lecture on Scale-Up of New Technologies', including seven case studies drawn from over fifty years of full-scale industrial projects. The students are taught the basic concepts of scale-up, including the limits of pure theory and the need for empiricism. Insights from real scale-up failures and successes are fictionalized as Projects A, B, C, etc. The students are then asked to identify the guiding principles that can be distilled from these case studies.

Jan 1, 2011

By W. H. Hastings

Introductory In the amount of her coal reserves, Saskatchewan ranks third among the provinces of the Dominion, with a total, as estimated by D. B. Dowling, of 59,812,000,000 tons. All the coal so far discovered in the Province is lignite, and it would appear unlikely that bituminous or higher grade coals exist. General Occurrence of the Coal The location of the coal-bearing formations in Saskatchewan is shown on the accompanying map. It will be seen that the areas lie principally in the southern part of the Province. The more darkly shaded areas indicate locations where development is taking place, or where coal-seams are known to occur, either through outcrops in valley-sides or through having been encountered during boring operations. The coal-seams are not necessarily continuous throughout the shaded areas, but in all pans of these there are coal possibilities. It is quite possible that small outliers of the coal-bearing formations may occur further north in the Province, but, generally speaking, coal is not likely to be found outside the shaded areas.

Jan 1, 1929

By A. Jafarnia

Aluminum alloys are frequently grain refined during solidification in order to promote the formation of an equiaxed grain structure in the casting. The application of Ti-based grain refiners and/or Ti containing master alloys for improving mechanical properties may result in formation of Al-Ti based intermetallics. Although the grain refinement produces many desirable qualities in aluminum castings such as improved castability and mechanical properties, the addition of Ti to Al-Si foundry alloys may lead to the formation of some undesirable intermetallic particles such as AlTiSi and cause a number of operational problems such as nozzle blockage due to segregation and agglomeration of aluminide particles within the nozzle. There are several questions to be clarified when minor amount of Ti is added to Al-Si alloys. They include nucleation and growth of AlTiSi particles, their morphologies and orientation relationships with aluminum matrix and the dissolution of these intermetallics during the course of solidification and/or post solidification treatments. The current study was initiated to study the process and possible mechanism of aluminide dissolution and the related phenomena such as segregation and agglomeration. It reports the results found during reheating of laboratory prepared Ti-added A356 alloy at three temperature ranges of below solidus, mushy zone and above liquidus.

Jan 1, 2004