Search Documents

By G. Bylapudi, K. Mondal, J. Hirschi

ABSTRACT: Rock bolts are the main form of defence against rock falls in mines. Conditions under-ground are conducive to corrosion. A perception exists about American coal mines that bolt corrosion is not an issue, especially when bolts are fully grouted. This perception is not necessarily accurate due to the formation of micro-cracks as the resin sets and to subsequent rock movement that breaks the resin column’s continuity. Corrosion should be considered when designing rock bolt support in long-term excavations. This paper explores the problem of corrosion, outlines a method to determine the corrosion potential of bolts, and suggests ways to mitigate such effects.

Jan 1, 2010

By Anthony Finch

Many mines combine open pit with underground mining, and on many occasions the underground mine is an extension of the open-pit. In these circumstances the decision about where the open-pit stops and the underground starts is crucial and driven by many factors. This paper looks at some of the ways that this cut-over can be calculated and specifically examines the calculation of it using modern mine optimization software. The paper provides a case study which will review various outcomes using these techniques, and demonstrates the influence of various factors on the optimal transition cut-over point. Biographies Mr Finch is a Divisional Manager and a Principal consultant at Snowden Mining Industry Consultants in Vancouver, Canada. At Snowden Mr Finch leads a team of engineers that perform mining engineering studies for projects around the world. Prior to joining Snowden Mr Finch was the Mining Manager at Barrick?s Henty mine in Tasmania Australia. Prior to that Mr Finch has held a variety of roles in both consulting and operations working for various organisations at various levels in the Asia Pacific region. Mr Finch gained a bachelor?s degree in Mining Engineering from the University of Queensland in 1986, and a bachelor?s degree in Economics from the University of Queensland in 1993. His expertise is in mine planning, mine optimisation and mine management. Dr Elkington is a Consultant at Snowden Mining Industry Consultants in Perth, Australia. He is responsible for the design and implementation of Snowden?s proprietary optimization software products. Prior to joining Snowden Dr Elkington completed his PhD in Mine Optimisation at The University of Western Australia, and bachelor?s degrees in Engineering (Hons) and Commerce from The University of Western Australia. He specialises in optimization and trade-off studies, and has consulted on projects across all major commodities and regions.

May 1, 2011

Accountability for profit realized or lost, and responsibility for continued safe operation are the main impetus behind operator training. Efficiency in operation enables production at lower unit costs. An inefficient operation eats profitability of the operation, creating short term losses, and also affecting longer term viability particularly when commodity prices fluctuate and competition erodes market share. Safe operation and efficient operation are ultimately conjoined entities which may not be able to be sustained without dual effort. Training is a very valuable tool to engage operations in adopting more efficient and safe practices. Training requires time, facilities and trainers. One novel way of minimizing both the trainers and the facilities is through the use of Computer Based systems. Included amongst this are Computer based equipment simulators, following an identical philosophy as flight simulators used for pilot orientation and training for different aircraft types.

Feb 1, 2008

By Tim Gartner

This paper introduces a new application of a proven technology to provide dynamic, voltage regulation in underground mine electrical distribution systems. This technology acts to ?stiffen? the electrical power feeding continuous miners and generally raise and improve the voltage regulation at the continuous mining machines which may be located over long cable distances from the mine incoming electrical substation. This is extremely valuable for large underground continuous mining operations that use high power electrical mining machines fed over very long cable lengths (measured in 10s of km, from mine shaft to mine operating face). This new technology provides fast acting dynamic voltage regulation (voltage support) while starting continuous borers and extensible conveyor belts. Additionally, if the mine suffers from a lower distribution voltage due to long cable lengths, this new technology will raise the overall voltage at the mining machine, which can increased mining machine production and lead to longer motor life. The technology is based on voltage source converters operating as static VAR compensators specially packaged for the harsh underground mine environment. While static VAR compensator technology has been successfully used in utility and large industrial applications for many years (including open pit mining and arc furnaces), it has not (until now) been applied in underground mining. The paper will present the problem of poor voltage regulation in underground mines on weak electrical utility networks. It will then discuss some of the alternatives that have been used to resolve this voltage problem. It will then introduce the new technology used to solve the problem and review the issues involved in using this technology in the harsh underground environment. Finally, the paper will present preliminary performance results from an actual installation in a large underground continuous mining operation in Canada.

May 1, 2003

By M. Xiao Bo

In recent years, there has been a heightened interest in the hydrometallurgical processing of sulfide ores and concentrates (especially copper sulfide ores and concentrates) mostly in the USA and Chile. Currently, hydrometallurgical operations account for about 30% of the primary copper production. In the present research, the leaching phenomena of IOCG (iron-oxide hosted copper-gold) ores and concentrates were studied. The IOCG ore, which is characterized as having a predominant amount of magnetite with fine chalcopyrite, is currently the center of attention for new copper resources. Heap leaching of IOCG ore is desirable because of its low cost. However, the leaching characteristics of the ores and concentrates and the mechanisms of copper leaching require investigation. This study defines the factors, which affect the leaching operation, such as the ORP, pH and oxidizing agents. Based on these results, the optimal leaching conditions are provided for pilot column leaching test and ultimately, commercial operations.

Jan 1, 2007

By Gaston Giuliani, Jérome Massot, Didier Bourlès, Lionel Siame

"Abstract - We present a new approach for the evaluation of the potential of emerald reserves in gem projects using beryllium (Be) mobility. The distribution of Be in the different phases of hydrothermally altered (albitized) black shale hosting Colombian emerald deposits indicates that Be mobility is associated with the breakdown of Fe-Mn oxyhydroxide phases. The amount of Be that can be mobilized (~0.7 x 10-6 g/g; i.e., 0.7 ppm) may represent up to 18 wt% of the total Be contained in the black shale. A mass balance calculation applied to a well-constrained alteration zone of the Chivor mines, and based on the quantification of Be that can be mobilized under hydrothermal conditions, gives an estimate of the total gem reserves of these mines. Resumé - Une nouvelle approche, basée sur la mobilité du béryllium (Be) pour l’évaluation des réserves d’émeraude dans des projets d’exploitation de gemmes est présentée. La distribution du Be dans les différentes phases minérales de schistes noirs hydrothermalisés (albitisés) qui contiennent les gisements d’émeraude colombiens, indique que le Be mobilisable se trouve dans les oxyhydroxydes de fer et de manganèse. La quantité de Be potentiellement mobilisable (~0,7 x 10-6 g/g; soit 0,7 ppm) constitue jusqu’à 18% poids du Be global contenu dans le schiste noir. Un bilan de masse appliqué à la zone d’altération hydrothermale des mines de Chivor et basé sur la quantification du Be mobilisable, donne une première estimation des réserves à émeraude de ces mines. rieur."

Jan 1, 1999

By A. R. Guest, R. Clayton, J. Jakubec

"The potential for mudrushes is a potential hazard that should be evaluated during cave mining studies. Mudrushes are a phenomenon that can have very different origins, but produce the same results: injury, loss of life, damage to property, excess dilution, production delays, or mine closure. Although mudrushes are more common in cave mines than other mines, any mining activity that enables the accumulation of fine particles and water is susceptible to mudflow. This paper describes the process developed by the authors during the past decade to evaluate the risk of mudrushes, specifically in caving and sublevel caving mines.RÉSUMÉ Un danger potentiel qui devrait être évalué durant les études d’exploitation par blocs foudroyés est la possibilité d’afflux de boue. Le phénomène des afflux de boue peut avoir des origines très diverses; les résultats sont cependant les mêmes : des blessures, des pertes de vie, des dommages à la propriété, une dilution excessive, des délais de production ou des fermetures de mines. Bien que les afflux de boue soient plus fréquents dans les mines exploitées par blocs foudroyés, toute activité minière qui permet l’accumulation de particules fines et d’eau est sujette à des coulées de boue. Le présent article décrit le processus développé par les auteurs au cours de la dernière décennie pour évaluer le risque d’afflux de boue, surtout dans les mines exploitées par blocs foudroyés et par sousniveaux foudroyés."

Jan 1, 2016

By A. Pranowo, G. R. F. Alvear F., N. Aslin, M. S. Moats

"The toxicity of arsenic is well known and documented; however, the presence of arsenic in copper electrorefining anodes and electrolytes is critically necessary to produce high-quality cathode. Arsenic as well as antimony and bismuth concentrations vary relative to their concentration in the anode copper received from the smelter. The behaviour and benefits of arsenic in copper electrorefining and the detrimental effects of antimony and bismuth on cathode quality and tankhouse performance are discussed. This will include the minimization and mitigation of problems associated with arsenic, antimony, and bismuth—including cathode contamination, floating slimes, scaling, and anode passivation.RÉSUMÉ La toxicité de l’arsenic est bien connue et documentée; toutefois, la présence d’arsenic dans les anodes de l’électroaffinage du cuivre et dans les électrolytes est d’une nécessité critique pour produire une cathode de grande qualité. Les concentrations en arsenic, ainsi qu’en antimoine et en bismuth varient selon leur concentration dans l’anode de cuivre reçue de la fonderie. Le comportement et les avantages de l’arsenic dans l’électroaffinage du cuivre et les effets indésirables de l’antimoine et du bismuth sur la qualité de la cathode et le rendement des cuves d’électrolyse sont discutés. On traite aussi de la minimisation et de l’atténuation des problèmes associés à l’arsenic, l’antimoine et le bismuth – incluant la contamination de la cathode, les schlamms flottants, l’entartage et la passivation de l’anode."

Jan 1, 2016

By J. Lu

The impact of acid treatment in agglomeration/acid curing on copper extraction and acid consumption was investigated with respect to acid dosage and moisture. Without the addition of water, no agglomeration occurred. At an acid dosage above 15 kg/t, the acid was not completely consumed during acid curing. With the addition of 6.2% water, the particles agglomerated together. Copper, iron, magnesium and manganese were dissolved as sulfates and enriched in the fine fraction of the ore. The copper extraction and net acid consumption increased with increasing acid dosage. The copper extraction for acid curing with the addition of 6.2% water was higher than that without the addition of water due to the improved permeability and the increase in the contact with acid-soluble copper. During acid curing, the reaction of sulfuric acid with muscovite, abite and nacrite mainly took place on the surface of the particles while the reaction of sulfuric acid with clinochlore occurred not only on the surface but also inside the particles.

Jan 1, 2007

By Joseph J. Poveromo

The blast furnace today continues as the primary production method of hot metal in large-scale steel production. The blast furnace process has been the target of repeated attempts to replace it with various process options, including direct reduction and coke-free smelting reduction. While these new technologies are being adopted in appropriate niches, the blast furnace has responded to the challenge by being amenable to continuous improvement. I will review the role of the blast furnace, major developmental and improvement trends, and then list the current important issues in ironmaking. I will outline the challenges to be faced by the blast furnace to maintain its position as the primary hot metal production process. The material presented here is an update of earlier presentations made in Stockholm, Sweden, 1996, Duluth, 1998 and Chicago, 2000.

May 1, 2003

By Kostas Fytas

Acid mine drainage (AMD) is a serious environmental problem that preoccupies the Canadian Mining Industry. Considerable amounts of money are spent every year in an effort to prevent or reduce the acid mine drainage phenomenon. AMD occurs when sulphide minerals (ex. pyrite) contained in rock are exposed to air and water and subsequently oxidize to produce low pH water. This acid effluent has the potential to mobilize any heavy metals contained in the rock. Coating the sulphide minerals with silicates is a new promising technology to reduce AMD. Pyrite is treated with a solution containing H2O2, sodium silicate and a buffering agent. H2O2 oxidizes a small part of pyrite producing ferric iron (Fe3+) ions. These ions subsequently react with the silicate ions to produce ferric hydroxide-silica that precipitates on the pyrite surface producing a passive coating. This silicate coating can protect the grains of pyrite from oxidation. This paper presents a series of experiments that confirm that silicate coating can considerably reduce AMD.

May 1, 2001

By S. Koski, M. Schmalzel, D. A. Jacobson, S. Crosby, P. Cook, M. Mular

"Mining operations, whether new or existing, are constantly looking for ways to maximize production and improve energy efficiency, while keeping the footprint required to a minimum. The Nordberg MP1250 cone crusher was designed with these three goals in mind. A series of side-by-side evaluations comparing an MP1250 to an MP1000 were completed at two Freeport-McMoRan operations. The first evaluation began October 2009 in a tertiary position and the second began March 2010 in a secondary position, where it remains in full production today. Utilizing 25% higher power capacity than the existing MP1000 tertiary crushers, the MP1250 had 29% higher capacity and 17% lower specific energy, adjusted for differences in feed and product size. The MP1250 compared to the existing MP1000 secondary crushers achieved 30% higher capacity at a slightly reduced specific energy, while achieving a finer product.The MP1250’s higher capacity and energy efficiency may have application in many crushing plants. Depending on site specific economic factors, greenfield projects may benefit from a smaller footprint and less ancillary equipment, whereas brownfield projects may benefit from higher capacity or a finer product within the same footprint."

Jan 1, 2012

By Pavel Vasak

Microseismic monitoring is becoming standard practice in the Canadian mining industry, particularly as mines get deeper. Full-waveform microseismic systems allow the operator to distinguish the event source mechanism, e.g., blast, shear slip or stress-induced fracture. At mine sites that heave a microseismic system operator blasts are manually identified by comparing the event waveform traces to the morning blast logs. However, this procedure is not routinely done at sites where a system operator is not present and this can lead to misinterpretation of the data at a later stage, particularly where the interpretation is outsourced, often many years later. It is critical to improve the microseismic data quality and consistency for processing and interpretation with a reliable technique to filter out blasts and blast related seismicity. This paper presents the development and implementation of a simple blast identification and filtering routine. The routine was developed specifically for Vale?s Creighton Mine about a decade ago, but is made sufficiently general so that it can be used at any mine site with an ESG (Engineering Seismology Group Canada) based full-waveform microseismic systems. The routine is strictly a post-processing procedure developed for use with the Access database data structure used by ESG. The algorithm was tested at Creighton Mine and a success rate of 80 to 90% was achieved, when compared to manual blast picks.

Oct 1, 2010

By Simon C. Dominy, Alwyn E. Annels, Mark A. Noppé

Abstract - Mineral Resources and their subsequent conversion to Ore Reserves are of key importance to mining companies. Their reliable estimation is critical to both the confidence in a feasibility study, and also to the day-to-day operation of a mine. Together with sampling, assaying, geological and other errors introduced during interpretation and estimation, additional errors are likely to be introduced during the application of technical and economic parameters used for conversion of resources to reserves. There is thus a requirement for high-quality interpretation and estimation to be supported by high-quality data. Any company expecting to make sound investment or operational decisions must base this on both relevant and reliable information. An Ore Reserve statement generally contains a single set of grade and tonnage figures without a discussion of the potential inherent errors in these estimates. Some sensitivity studies may be run, but confidence limits are rarely quoted and, if they are, often do not take into account many of the factors that cause uncertainty in the grade and tonnage estimates. Mineral Resource and Ore Reserve estimates thus carry certain errors leading to uncertainty and risk; some of these are unquantifiable for various reasons, for which the operator should be aware. This paper presents a review of the potential sources of error that might occur during a resource estimation program, which are carried through into the reserve estimate. A number of methods are discussed that allow the estimator to be more transparent about the inherent risks in his/her estimate. Emphasis is placed on data quality, and the requirement for strong quality management to be linked to continuous improvement.

Jan 1, 2002

By Edouard Masengo

A long dyke will be constructed in a lake with rockfill placed by end dumping method. Its crest will be at elevation 521.5 m compared to the nominal lake level at 520 m. In the first portion, its height will vary from 1.5 m on a 35.1 m thick tailings layer to 18.3 m on about 0.5 m of tailings. In the second portion, the dyke will be built on native silty clay and will vary from 18.3 to 15.2 m in height. The tailings consist in stratified layers of fine-grained soils showing lateral and vertical segregation. The tailings are compressible and may develop excess pore water pressure on loading. The tailings overlie a thin layer of relatively soft native silty clay. The till beneath the silty clay is considered incompressible compared to the material above. After construction, as the tailings and silty clay consolidate, pore water pressures will dissipate and dyke stability will improve. Since dyke stability will increase with time, the primary concern is its stability during construction. As a result of construction activities, three potential modes of failure were identified and recommendations were provided regarding the measures that should be undertaken to increase dyke stability during construction.

May 1, 2003

By Clifford R. Stanley

"Abstract - Reproducible analyses of representative samples for elements affected by the ‘nugget effect’ is vital in mineral exploration and reserve estimation. Unfortunately, a priori knowledge of what size of sample is representative from a mineral deposit or its dispersion train is commonly unavailable. Use of the simple ‘equant grain model’ and the NUGGET computer program facilitates determination of the sampling parameters that will produce appropriate samples for chemical analysis. Based on Poisson statistics, NUGGET can be used to determine: (1) the ‘effective grain size’ of nuggets in a suite of samples, (2) the level of representativity (precision) that samples with specific nugget grain sizes will exhibit, and (3) the sample size required to obtain a specific level of sample representativity. The program determines these sampling parameters for any element in any mineral, including solid solution minerals (e.g., Au, electrum, Pt-Fe alloy, diamond), and allows assumption of a variety of grain shapes (e.g., ellipsoids, cylinders, parallelepipeds, etc.). Furthermore, it outputs the effective number of nuggets expected in a sample of given size and the percentile confidence bounds on any element concentration affected by the nugget effect.Results from the software allow determination of effective sampling and analysis strategies that minimize the nugget effect in geochemical analysis/assaying used in mineral exploration and reserve estimation. This will not only improve confidence in the resulting exploration results or reserve estimate, but will facilitate estimation of the error associated with any subsequent interpretation or reserve figure."

Jan 1, 1998

By W. J. Mcgaughey, M. A. Vallée

"Abstract -The application of geophysical technology to resource delineation aims to improve the quality of resource/reserve estimates by integrating high-resolution survey methods, geophysical modeling and inversion with three-dimensional representations of geological and mineral deposit data. The use of geophysics can cost-effectively improve a geological interpretation based only on geological and sampling data. Success depends upon the ability to use geological visualization and modeling software, first to develop a three-dimensional geological model and then to modify it interactively by integrating geophysical data with the geological and sampling data.The high resolution required for mineral delineation geophysics results in a focus on borehole seismic and high-frequency electromagnetic methods. Borehole wireline logging is used to develop an understanding of the relationship between physical properties and geological description. Data from core samples and borehole wireline logs allow the construction of a three-dimensional physical property distribution, consistent with the existing geological interpretation. The three-dimensional physical property distribution is used for both geophysical forward modeling (to compare to field data) and as a starting model in iterative inversions.Advanced visualization techniques allow the simultaneous viewing of the three-dimensional physical property model, the geological information and data from which it is derived, and the geological interpretation and the geophysical results. Geophysical results may be simulated responses from a forward model or the output from a numerical inversion in the form of an updated physical property distribution. Iterative refinement of the geological interpretation is required to ensure consistency with the geological and geophysical data. The key to success with this approach is that all relevant geological, geophysical, and rock property data reside in a common, visual model of the earth.Examples from massive sulfide deposits illustrate the benefits obtained by the integration of geophysical and geological data."

Jan 1, 1998

By G. de Alva

"Industrias Peñoles S.A. de C.V. (Peñoles) is a private enterprise and is the main silver producer in Mexico. Peñoles is a Mexican Company, and since 1887 ranks as one of Mexico's main natural resources industrial groups.Peñoles Mining Group includes six operating Companies producing mainly gold, silver, lead, and zinc. All mines are underground operations, and the ore is milled in ten concentrator plants near the mine sites. Plant throughputs range from 150,000 to 810,000 tonnes per year.This paper gives a general view of the Peñoles Mining Group, their type of deposits, mining methods, and mineral processing work practices.The paper also discusses some of Peñoles work philosophies and measures being adopted to become more competitive. Due to the small size of the deposits, the mining methods used and size of the concentrator plants are somehow different to those typically seen in large deposits. This could make the paper more interesting.IntroductionIndustrias Peñoles S.A. de C.V. (Peñoles) since 1887 ranks as one of Mexico's main natural resources industrial groups; initially in the mining field and afterwards in the metallurgical, chemicals and refractories areas.Peñoles is integrated as follows: a Mining Group; an Exploration, Engineering and Construction Groups; the Metals Group; and the Chemicals Group.Peñoles is a Mexican Corporation devoted to the location, extraction, industrialization and commercialization of natural resources under its control, performed in an efficient and responsible manner for the benefit of its shareholders, employees and the communities where it operates, through blending and managing a portfolio of sound highly profitable business, offering products and services with integral quality; leaders in their respective fields or with an outstanding presence; technologically and operatively effective, with ecological consciousness and international projection, and an image of prestigious integrity."

Jan 1, 1996

By S. Banisi, J. A. Finch, A. R. Laplante

"A technique for on-line simultaneous estimation of gas and solids holdup (volume fraction), based on a combination of conductivity and pressure difference measurements, is proposed and tested in a laboratory flotation column (10cm in diameter and 447cm in height). Fundamental concepts underlying this technique and the effect of relevant parameters are discussed. In the studied range, 3-30 %v/v gas holdup and 2-18 % v/v solids holdup, experimental results showed good agreement between the estimated and actual holdup values (as determined by an isolating technique). The relative accuracy of the solids holdup estimation increased when solids density or solids concentration increased. Frequent re-calibration of pressure transducers was found necessary for accurate phase holdup estimation.IntroductionGas holdup is a key parameter in controlling the performance of flotation columns. For example, flotation rate is affected by bubble size and gas rate both of which, in turn, affect gas holdup. Moreover, gas holdup also determines the slurry residence time which indicates a direct influence of gas holdup on recovery.Gas holdup determination has been the focus of many studies (e.g., Castillejos, 1986; Marchese et al., 1992). Some of the techniques which have been used are given in Table 1."

Jan 1, 1994

By T. Gonzales, S. Thakurdin

The conducting of risk reviews is an essential activity in ensuring safe operating conditions, both during project design phases and for existing facilities. The following paper presents a structured approach to the conducting of risk reviews for existing operations, including descriptions of supporting documentation and guidelines for on-site review activities. The conducting of regular site risk reviews and safety audits is crucial in ensuring the continued safe operation of existing facilities, particularly in the copper industry where numerous processes and unit operations can present catastrophic risks, both in terms of loss of life and financial liability. The structured approach presented aims to provide a logical and comprehensive analysis of risks to align safety-related facilities and procedures with current industry best practice and ensure consistency across multiple client operations. INTRODUCTION The production of copper, whether by pyrometallurgical or hydrometallurgical process routes, carries significant inherent safety risks. Production volumes are relatively large, often requiring complex processing routes, multiple production trains and a variety of supporting ancillary facilities. Furthermore, considering the relatively large size of ore reserves, copper production plants can have operational lives well beyond the typical design duration of 20 years. In this context, the conducting of regular risk reviews is essential in ensuring safe operating conditions and aligning facilities with current industry best practices. Risk reviews and safety audits can take various forms and have various areas of focus. The methodologies and approaches described below relate specifically to catastrophic risks, defined broadly as risks that carry the potential for multiple fatalities and significant financial losses. Focus is given to existing facilities and does not consider the risk-related activities such as hazard and operability (HAZOP) studies conducted during plant design. The structured approach presented aims to provide a guide for effective site- based audits and a logical analysis of risks identified. RISK CLASSIFICATION Table 1 provides a typical summary of the classification of risk types and the associated consequence categories and descriptions. It illustrates the descriptions of a catastrophic risk in terms of the broad categories of Health & Safety, Environment, Financial, Image & Reputation and Legal & Compliance. In terms of the Financial category, numeric costs ranges are often prescribed depending on the financial characteristics of the specific operation and the associated parent company.

Jan 1, 2019