Search Documents

By H. J. Chalmers

"Since the advent of large volume flotation machines, Cominco Ltd. has actively studied possible application of such machines to their various milling operations. A number of installations have been made and more are on the drawing board. This paper gives a description of these units, information as to choice of equipment, and information as to operating experience. Mechanical and operating details of six installations are summarized. Three different types of machines are discussed.Pine PointThe original Pine Point zinc flotation circuit comprised conventional roughing with two stages of cleaning. Over the years with increase in feed tonnage there have developed two adverse conditions; namely, a reduction in zinc concentrate grade coupled with an increase in MgO in the concentrate. This resulted in higher freight payments along with more severe smelter penalties. An intensive test program, in 1971, showed that the concentrate grade could be raised by 1.5 units of zinc along with a reduction in MgO from 0.8% to 0.47.. Subsequently this was done by adding two additional stages of cleaning using 16 cells of Denver 200-V's. The project was completed in January 1973 at a cost of $510,000 to give an estimated annual savings of about $390,000.Selection of the Denver Model 200-V was based on minimum floor space requirement, availability, and favourable operational and maintenance experience with Denver 100’s. As it happens it was possible to ""shoe-horn"" the 16 cells into place with a minimum of plant alteration. Some problems have been encountered with a tendency to ""sand up"" at high pH, particularly at the corners. Otherwise operational service has been very good."

Jan 1, 1974

By Mark B. Thorpe

Golden Star Resources started gold mining operations in Africa in 1999 after 15 years of exploration in South America. At the time, the approach to local assistance was through "alternative livelihood" programs and the donation of infrastructure to local communities. This was initially successful with local community support. However, with time and on reviewing the implemented projects, it became evident that the success was limited and many if the projects were either poorly used or in disrepair. Through a review of the options, we decided to develop a community assistance model driven by the communities themselves, while keeping control of the finances and the actual construction of the projects. Through the formation of the Golden Star Development Foundation, we began to support community driven projects for local economic development. The evolution of economic development projects continued over the next several years with the addition of project requirements for partnerships with government, and finally an evolution to a partnered turn-key piece of infrastructure that we hand over to an agency for operation and ongoing maintenance. We are currently working with outside partners to further our economic development activities in Ghana to the benefit of our stakeholders.

May 1, 2011

By Norma G. González

La littérature et notre expérience en Bolivie dans une communauté minière très divisée comme celle de Huanuni nous montrent le besoin d?envisager des négociations gagnant-gagnant entre communauté et entreprise minière, non pas comme un point de départ, mais comme un résultat à atteindre, qui nécessite la préparation de conditions préalables. Cela implique fondamentalement de mettre l?accent sur le processus qui permettrait par la suite aux parties de mieux traiter les questions de contenu. Suivant cette hypothèse générale, l?initiative conjointe entre le Ministère des ressources naturelles du Québec et le CECI ?Développement des mécanismes de négociation entre communauté et entreprise minière? peut dégager, après un an et demi d?expérience pilote dans le site minier de Huanuni, département d?Oruro, Bolivie, les leçons préliminaires suivantes. Ce processus requiert: ??Agir, en tant qu?organisme consultant tierce partie, selon des principes et une méthodologie qui relèvent de la Communication publique et de la Médiation ; ??Comprendre et agir à partir de la ?réalité sociale? des parties en présence: l?entreprise minière, l?État et les différents groupes de la communauté; ??Intervenir sur les ?réalités sociales? des parties, par des actions d?éducation et de diffusion dans le but de préparer les personnes, les institutions et les organisations de la société civile, à des changements durables du modèle de communications existante; Approfondir la compréhension de la ?réalité sociale? du conflit (la culture du conflit, les méthodes populaires de résolution des problèmes et de gestion des conflits) afin d?offrire aux bénéficiaires les technologies appropriées pour la transformation de cette culture de confrontation violente en gestion constructive des conflits. Par ricochet, nous espérons ainsi faciliter l?attraction des investissements dans le secteur minier.

May 1, 2001

By K. Chotruangprasert

This paper explores Global Reporting Initiative (GRI) reporting practices within the mining industry. Specifically, this paper investigates how and why a mining company makes voluntary reporting decisions to include the GRI indicators that may be considered ?negative? to the company?s reputation. Due to the voluntary nature of the GRI Guidelines, a GRI adopter is not legally obligated to report every GRI indicator. Not surprisingly, empirical studies that evaluated the extent to which companies? sustainability reports meet the GRI requirements (Guenther, Hoppe, & Poser, 2006; Morhardt, Baird, & Freeman, 2002; Samy, Odemilin, & Bampton, 2010; Skouloudis, Evangelinos, & Kourmousis, 2009) have found that reporting practices of the companies under their studies are well below the standards reflected in the GRI Guidelines. An influential study by Clarkson et al (2008) uses economic-based and socio-political theories to explain variation in companies? environmental disclosure. They have found that, as predicted by economic-based theory, superior environmental performers disclosed more ?hard? (i.e. verifiable) environmental information. Inferior environmental performers are found to disclose more ?soft? (i.e., not easily verifiable) claims, which is consistent with socio-political theories (Clarkson, Li, Richardson, & Vasvari, 2008). However, this study and the existing literature do not adequately explain why a company may act in a way that cannot be explained by economic-based and socio-political theories, for example, why it would report some negative soft data that it is not required to report. This paper intends to address this literature gap. GRI reporting by a Canadian mining company, which I would like to call ?Company C?, is used as a case study for this paper. Company C was selected for this research because in addition to ?positive? information, its GRI-based sustainability report also includes both hard and soft ?negative? information such as grievances. Research methods include interviewing Company C?s employees who are involved in preparing GRI reports and reviewing documents prepared both by the company and by external parties. I find that integrative social contracts theory (ISCT) offers a valuable explanation to Company C?s reporting practices. From the ISCT perspective, Company C?s management appears to feel that the company is obligated under social contracts to be transparent. Therefore, Company C disclosed both positive and negative social and environmental information to the public because the management appeared to think that it is the right thing to do. At the same time, being transparent about the bad news gave the company an opportunity to conclude that it had done something to avoid future occurrence of the negative incidents. Therefore, I propose that, in addition to the economic and socio-political theories that are more often used in literature, insights from ISCT are instrumental in improving our understanding of the corporate non-financial reporting practices phenomenon.

Aug 1, 2013

By Miguel A. Cuba

Trends in the mean and/or variance are a longstanding challenge in mineral resource modeling. Geologic modeling and/or grade domaining are often employed to account for heterogeneities in mineral grades; however, this is only practical up to a certain point since the number of data available for reliable model construction can be severely reduced. In such cases, trends remain present in certain geologic/grade domains and directly impact the modeling methodology; the trend must either be handled explicitly or a suitable approach is adopted to implicitly account for it. This is highly dependent on understanding the source of the trend. We propose an approach that detects the source of non-stationarity, which is based on quantifying the impact of non-stationarity in the mean and the variance via the semivariogram. By expanding the methodof- moments approximation of the semivariogram, we decompose the experimental semivariogram is into three terms: 1) trend in mean component, 2) trend in variance component and 3) stationary component. We can then assess the source of trend by calculating the contribution of each component at every lag. Two cases are presented to illustrate this tool. Firstly, a synthetic reference model is simulated and different trend patterns are added; the influence of these patterns in the experimental semivariogram calculation are analyzed and discussed. Secondly, a real dataset is considered where the impact due to the presence of trends in the mean and variance are assessed. The results of this paper reveal the semivariogram to be a tremendously powerful tool in determining the source of the trend. This insight may be useful in the selection of a suitable modeling approach for resource estimation.

Oct 1, 2009

By John Keay, Douglas R. Shaw, Gregory J. Olson

"The results are presented herein of on-going laboratory investigations of heap bacterial oxidation as a pretreatment method for the recovery of sulfide-encapsulated gold from ore samples of the Rhodes Mining Lahoca deposit, located in northern Hungary. The ore contains just over 2 g Ault and as much as 6% sulfide, mostly as pyrite. Laboratory aerated column tests conducted at Colorado Minerals Research Institute (CMRI) showed that mild to moderate biooxidation of the finely crushed ore occurred rapidly in approximately three months, with cyanide gold recoveries of up to approximately 60%. The results contrast cyanide gold recoveries of less than 30% from non-pretreated ore. Mineralogical examination of biooxidized residues indicated that the mechanism of biooxidation of crushed ore was related to microorganisms following pathways along structural anomalies in the pyrite grains. Such selective biooxidation is an important result to minimize the biooxidation and aeration time and effluent neutralization costs in a commercial operation.IntroductionThis paper describes the development of a heap biooxidation process for the Lahoca gold project The Lahoca deposit is situated in northern Hungary, at the site of a former copper mining area. Lahoca is a large tonnage, relatively shallow, deposit amenable to open-pit mining Lahoca has the potential to produce I 00,000 ounces of gold annually for at least ten years at its minimum reserve base.The laboratory test work conducted initially by Rhodes Mining NL demonstrated that the Lahoca refractory ore is amenable to whole ore and concentrate oxidative pretreatment and cyanidation. Capital and operating costs, however, for such milled ore treatments were considered relatively high. Rhodes Mining subsequently evaluated heap leaching methods, particularly heap biooxidation pretreatment, as a process route that promised superior economics suitable for exploiting lower gold grade refractory ores.This paper focuses on the laboratory column (simulated-heap) biooxidation test work, particularly the proposed mechanism of selective microbial oxidation, wherein only a small amount of the sulfides are oxidized sufficient to allow commercially acceptable gold recoveries by conventional cyanide heap leaching. Selective or minimal biooxidation of sulfides is considered important to minimize biooxidation time and aeration requirements, as well as acid effluent neutralization costs."

Jan 1, 1998

By David W. Mogk, Tamara Darsow, Macgregor L. Fogelsong, Robert M. Hunter, Frank M. Stewart, Edwin H. Abbott, Courtney A. Young

Abstract: Development of cost-effective techniques for recovering precious metals from their ores has been the goal of metallurgists for hundreds of years. Today, metallurgists are increasingly called upon to design processes for ores that are refractory to conventional recovery techniques. These challenges and the addition of environmental costs (including site remediation) to the total cost of mining have stimulated a search for alternatives to conventional processes, such as cyanidation. This paper describes the progress made to date in development of an innovative alternative to cyanidation, termed bisulfide leaching, for extracting gold, silver and platinum-group elements from refractory ores and concentrates. While bisulfide leaching can be implemented abiotically, significant benefits accrue from its practice as a bioprocess that integrates the steps of precious-metals liberation and extraction. In many applications, bisulfide leaching appears to offer significant advantages over the traditional cyanidation process. Dissolved bisulfide and hydrogen sulfide are much less toxic than dissolved cyanide and hydrogen cyanide. Recommended workspace exposure limits and harmful concentrations for hydrogen sulfide gas are higher than those for hydrogen cyanide gas. While the facilities required to practice the bioprocess on an industrial scale would be similar to that of cyanidation plants, chemical reagent costs could be 80 percent less. The bioprocess may also offer advantages in the leaching of ores and concentrates that are not amenable to cyanidation. For example, bisulfide leaching of ores containing carbonaceous material may produce higher gold recoveries if the "preg-robbing" characteristic of the material can be controlled biologically or with dissolved sulfide binding. Moreover, in that precious metals are much more soluble than base metals in bisulfide solutions, bisulfide leaching offers distinct advantages over cyanidation for selective dissolution of precious metals from base-metal concentrates. Thus, the bioprocess uses the natural sulfur cycle to mitigate pollutant production and to enhance precious-metals recovery.

Jan 1, 1998

By P. H. Riordon

ONE OF the major sources of the world's supply of asbestos lies in a belt of ultrabasic rocks stretching through the Eastern Townships of Quebec where chrysotile asbestos has been mined continuously since 1878. The productive portion of the belt extends from the town of Asbestos in Shipton town-ship northeastward some 60 miles to the eastern edge of Broughton town-ship. (See map). Twelve mines, currently treating an aggregate of over 60,000 tons of rock daily, produce more than one million tons of asbestos :annually. An equal number of mines are now dormant, having for the most part exhausted their reserves. It is evident from the past and present activity, in this belt that it can look forward to at least half a century or more of large scale production. The host rock to the asbestos de-posits is essentially a peridotite which originally contained I 0 to 15 per •cent pyroxene. The peridotite, associated with dunite, pyroxenite

Jan 1, 1962

By Joseph Bradley

THROUGHOUT this article, minerals used in the paint industry are designated 'pigments'. They may be classified in two groups: (1) Pigments which are used in the state in which they occur in nature, requiring only mechanical preparation. (2) Pigments which require heating or chemical treatment before use, in order to obtain from them a product of the desired quality or shade of colour. They may be further classified according to colour, as follows: White Pigments .-These include calcium carbonate (chalk, marble), gypsum and alabaster, kaolin-or china-clay, and magnesia. However, the white pigments most extensively used are compounds prepared chemically from minerals containing lead, zinc, titanium, and antimony. The white pigments are of particular importance because, not only are they used by themselves, but they also serve as adjuncts to other colours for the production of special shades. Yellow Pigments.-These are mainly naturally occurring ferric hydroxides, as limonite and bog iron ore, or similar. compounds prepared artificially. Brown Pigments .-Pigments of this group are distinguished for their beauty and depth of colour, and many of them are used in the finest of paintings. Familiar names are sienna, umber, and Vandyke brown. They are for the most part ferric hydroxides, containing varying amounts of water; but the group also includes a manganese brown, which consists chiefly of a mixture of oxide and hydroxide of manganese. Red Pigments.-Chief among this group is ferric oxide, known under various trade-names, such as Canadian red, Persian red, etc., and also the much prized and somewhat rare vermilion. The pigment used is either naturally occurring hematite, de-hydrated limonite, or artificially produced red ferric oxide.

Jan 1, 1937

By T. Yalcin

"This paper describes a process that can provide high rates of dewatering and that has the potential of bringing significant savings in tailing disposal costs. It involves a three-stage, closed-circuit operation employing a hydrocyclone, a settling cone and a thickener. The mill tailing, with adjusted pulp density, is first fed to the hydrocyclone. The underflow from the hydrocyclone goes to the settling cone for further dewatering. The overflows from the hydrocyclone and the settling cone are sent to a thickener which, with the addition of a flocculant, gives a clear liquid effluent and a dilute underflow which is recycled back to the hydrocyclone. The underflow of the settling cone is a material with as high as 78% pulp density and is suitable for direct disposal or for use as mine backfill.INTRODUCTIONDewatering is an essential process for the disposal of mill tailings and forms an additional cost item in milling operations. Cost-cutting measures are therefore desirable in this area as in any other stage of milling. One way of achieving this is through increased rate of dewatering which would require smaller dewatering units with correspondingly lower capital and operating costs."

Jan 1, 1987

By Abani R. Samal

The Fe assay values from the diamond drill-holes within a magnetite deposit of magmatic origin are utilized in this study. Only assay data from the unoxidized magnetite mineralization was utilized. The data from the overlying hematite mineralization zone was not used. A threedimensional block model estimated using ordinary kriging (OK) is used for analysis purposes. To estimate the non-linear standard deviations (s) and the confidence intervals (CI) of block estimates a discrete Gaussian variogram model is used in this project. The change-of support coefficient (rv) and the block-support correction are used in the ?block-anamorphosis?. A new calculated value of rv is 0.7283, implies that its influence in the block-anamorphosis is not significant. The CIs are calculated from the block-gaussian variables; then back transformed to the raw values. At 95% probability, the CI for the kriged block estimates of Fe values are calculated using Gaussian kriged estimates of the Fe and the corresponding standard deviations (Gaussian). The results indicate that the block estimates with a high influence from relatively small amount of samples can be identified as high-risk estimates.

Oct 1, 2009

By W. J. Witte, M. K. Witte

"INTRODUCTION A pilot heap leach project was conducted on the B. P. Selco Hope Brook ore located in southwestern Newfoundland. The pilot heap leach was undertaken to assess and confirm the following:1) To confirm that heap leach technology now currently used in the United States could be applicable to Canadian sites.2) To confirm gold recovery by the Heap Leach technology3) To assess and study potential heap leach environmental concerns in cold and wet climate.PROJECT LOCATIONThe Hope Brook Project is located near the southern coast of the island of Newfoundland, approximately 100 kilometers southeast from Stephenville, approximately 25 kilometers west of Burgeo, Newfoundland. Access to the property is limited to helicopter, float plane or by sea through Couteau Bay. The property was covered with muskeg and very few trees. Surface relief was moderate with many poorly drained boggy sections confined to small areas. Many small unnamed lakes were located on the property which provided water to small brooks and streams flowing to Couteau Bay.Several locations were reviewed for the installation of the pilot heap leach facility. Important parameters used to select a suitable location included sufficient land area, close proximity to but not on the ore body, reasonable protection from wind, sufficient supply of fresh water, close to a suitable location for a portable crushing plant, reasonable access to aggregate material for preparation of the test pad and ponds and suitable contours to minimize site preparation."

Jan 1, 1987

By Xian Jian Guo, Lei Li, Hua Wang

Direct smelting of copper concentrate to blister copper has the advantages of energy saving and environmental protection. There has been a lot of effort invested in process development including test work and theoretic analysis in the past half century. However, the process has only been applied commercially to a few smelters that treat chalcocite types of copper concentrate. The main limitation to treating chalcopyrite types of copper concentrate is high copper content in smelting slag and low direct copper recovery. Thus intensive slag cleaning is needed. In this paper, the thermodynamic analysis was mainly carried out for the multiphase equilibrium of direct to blister copper smelting for both chalcopyrite and chalcocite concentrates. The practical problems in direct to blister copper smelting, which are mainly in copper content in slag, are clarified. The operational window of slag composition for different temperatures and oxygen partial pressure for the treatment of chalcocite type concentrates is identified. The process operation optimization for the blending of chalcocite, pyrite and chalcopyrite concentrates was done. INTRODUCTION The extractive metallurgy of copper can be divided into two broad groups of processes, namely, pyrometallurgy and hydrometallurgy, and the former is dominant. About 80% of copper in the world is produced by pyrometallurgy (Christopher et al., 2006). The first stage of conventional copper pyrometallurgy processing is to smelt copper concentrate to copper matte composed of FeS and Cu2S with slagging to remove a proportion of the iron (Gargul, Boryczko, & Bukowska, 2017). The smelting processes include bath and flash smelting. The second stage of the process is to convert copper matte to blister copper. In most cases, the copper matte is converted in Peirce Smith (P-S) converters, which are batch operations (Kubiszewski, 2015). The P-S converting can be divided into two periods, slagging and copper blowing. During slagging period, FeS in copper matte is oxidized to FeO, which reacts with silica flux forming slag. When the iron content in matte is less than 1%, copper begins to oxidize and reduce to form blister copper (Kucharski, Sak, Madej, Wędrychowicz, & Mróz, 2013).

Jan 1, 2019

By D. A. McIsaac

In these days, when mass production seems to be the watchword of all industrial companies, nothing is left undone to attain this end. Transportation, where necessary, becomes a question of very great importance. For this reason every mechanical contrivance known to man is employed, with its resultant advantages. So successful has man's ingenuity been that, offhand, we are inclined to say that practically all transportation on a large scale is done mechanically, that is, where speed and economy are desiderata. Granting this, one would think that to read a paper on the horse before your honourable and highly technical Society would surely be a waste of time, and that any Company employing old-fashioned 'horse' power would certainly be very much behind the time, to say the least. However, the fact remains that the biggest industry in our country today-coal mining-must use horse power to a great extent, being compelled -both by considerations of economy and by necessity. For this reason,' in the production of coal under present conditions, the pit horse is of great importance to this industry and is to be considered seriously as one of the units that help to make coal mining a success or a failure. Hence, in employing horses as a power for transportation, care must be exercised in selecting the animals, and the care of this power must be considered as seriously as any other department of such an organization. In selecting a pit horse, several things must be borne in mind, that is, one must get as much horse power as possible in as compact a form as is practicable. This determines the type of horse we must use, which is of very great importance under our present conditions of coal mining. With low roof, steep grades, and forced production, a distinct type of animal must be selected.

Jan 1, 1930

By D. A. McIsaac

In these days, when mass production seems to be the watchword of all industrial companies, nothing is left undone to attain this end. Transportation, where necessary, becomes a question of very great importance. For this reason every mechanical contrivance known to man is employed, with its resultant advantages. So successful has man's ingenuity been that, offhand, we are inclined to say that practically all transportation ?On a large scale is done mechanically, that is, where speed and economy are desiderata. Granting this, one would think that to read a paper on the horse before your honourable and highly technical Society would surely be a waste of time, and that any Company employing old-fashioned 'horse' power would certainly be very much behind the time, to say the least. However, the fact remains that the biggest industry in our country today-coal mining-must use horse power to a great extent, being compelled both by considerations of economy and by necessity. For this reason,' in the production of coal under present conditions, the pit horse is of great importance to this industry and is to be considered seriously as one of the units that help to make coal mining a success or a failure. Hence, in employing horses as a power for transportation, care must be exercised in selecting the animals, and the care of this power must be considered as seriously as any other department of such an organization. In selecting a pit horse, several things must be borne in mind, that is, one must get as much horse power as possible in as compact a form is practicable. This determines the type of horse we must use, which is of very great importance under our present conditions of coal mining. With low roof, steep grades, and forced production, a distinct type of animal must be selected.

Jan 1, 1930

By E. G. C Charlesworth, M. J. Robertson

"Gold mineralization in the Main Reef Complex at Sheba Gold Mine is hosted within shear zones in a sequence of shales and greywackes of the Fig Tree Group. Competency contrasts between these rocks and a steeply dipping chert unit provided a locus for the development of right lateral steeply dipping shear zones. A set of flatter dipping shear fractures crosscut these zones with their intersections defining a system of en échelon ore shoots. Mineralization is both of vein type and disseminated strata-controlled replacement type. The latter occurs mainly within the wall rocks to the shear zones. Arsenopyrite and pyrite are the major sulfides, with arsenopyrite being confirmed largely to greywacke beds and pyrite to the more iron-rich shale units. Gold was introduced, together with minor sphalerite, pyrrhotite, chalcopyrite and early arsenopyrite, toward the end stages of a first pyrite phase. The mineralizing fluids were introduced along dilated cleavage planes and, emanating from these, produced a series of replacement fronts. Mineralization was syntectonic to late tectonic and occurred under conditions of progressive deformation, resulting in sulfides which are concentrated in the hinges of shear-related folds and semimassive sulfides within tension fractures which are folded, attenuated and fractured. An analysis of the structures shows a sequence of events in which an initial ductile simple-shear event with a steep sense of movement was succeeded by a more brittle strike-slip event. Mineralization is temporally related to the latter. This evolution in structural style was probably related to reactivation of the Sheba Fault as a transcurrent fault during emplacement of large granitoid bodies."

Jan 1, 1994

By K. Konigsman

"Representatives of various industries and the Canadian coast Guard formed a Bulk Cargoes Committee three years ago. In 1976 and 1978, I have attended the meeting which take place once per year here in Ottawa as representative of the Canadian Mineral Processors, Dave Hendricks from Granisle accepted the charge in 1977. Our Secretary, Bob Bruce, has suggested repeatedly that I report to the Membership on the deliberations to this group. Twice I found good excuses; this year I did not. I was reluctant to address you since the Committee's deliberation proceeded at a pace which might be identified as Government squared. The Committee advises a Government agency which in turn negotiates with foreign Government agencies.At the outset, I will describe the developments which led to the formation of the Committee and its purpose.The Canadian Mining Industry ships annually millions of tons of products to overseas customers; be it iron ore, coal, fertilizer, or base metal concentrates. Most loadings are in vessels of foreign registry and all will be directly affected by Canadian or International regulations of the transport of such bulk commodities. The major shipping nations are members of an Intergovernmental Maritime Consultative Organization (IMCO). This organization elaborates regulations which govern shipment of all cargo, bulk materials and concentrates included. At IMCO'S deliberations, Canada has one vote, one voice on the Consultative Committee and is represented by our Coast Guard. The Coast Guard has over the years been in contact with industries when discussions concerned shipment of bulk cargoes. In the early sixties, a ""Concentrate Committee"" did exist. It consisted of metallurgists from a number of mining companies and Government representatives. This committee was instrumental in the development of what became known as the ""Concentrate Code"", legislation which has evolved into the Canadian Bulk Cargoes Code as it is known today. The concepts of the flow moisture point and transportable moisture limit originated from its work. Incidentally, both criteria are widely accepted and utilized world-wide. The Concentrate Committee faded away once the Concentrate Code has been adopted."

Jan 1, 1979

By Engin Burak Anil

Objective, accurate, and fast assessment of damage to buildings after an earthquake is crucial for timely remediation of material losses and safety of occupants of buildings. Laser scanners are promising sensors for collecting geometrical data regarding the damaged states of buildings, as they are able to provide high coverage and accuracy at long ranges. Yet, we have limited knowledge on the performance of laser scanners for detecting earthquake damage, and requirements of such data collection. This paper focuses on characterizing the performance of laser scanners for detecting thin cracks for damage assessment of reinforced concrete frames. We identified a series of crack parameters based on the state-of-the-art damage assessment codes and standards. Similarly, we identified parameters, which affect the performance of laser scanners for detecting cracks, based on prior research in this area. We studied the width, depth, and orientation of cracks; sampling interval of the scanner, and the range of the laser beam from the surface. Effects of these parameters on the detection of the minimum crack size were determined in an experimental setting. An automated algorithm was used to analyze the data. The results show that it is possible to detect as small as ~1mm cracks.

Aug 1, 2013

By J. A. R. Faucher

"Autogenous grinding may be an efficient and economical solution to your ore comminution problem.An important potential economic advantage of autogenous mills results from the availability of very large capacity units.Autogenous grinding could be more economical in terms of both capital and operating costs.Satisfactory pilot plant testing and thorough economic evaluation are required for a sound decision in comminution plant selection.INTRODUCTIONMankind's first weapon was probably the wooden club, but men soon learned to shape, smooth and polish stone for tools and weapons by pounding and rubbing them with sand and water. It was only about four thousand years ago that rocks were first broken to concentrate, smelt and return the metals they contained. In spite of our recent great technological advances we still break rock in essentially the same manner that was used thousands of years ago - by pounding, rubbing and squeezing - and we still waste much energy and metal in the process"

Jan 1, 1969

By R. Scheepers

"Mineral deposits and prospects of the Pan African Saldanian orogenic belt in the southwestern Cape Province South Africa, are reviewed. Despite the entire absence of operating base or precious metal mines in the area, this study has established at least four metal associations that offer enticing exploration potential.The poly-phase deformed, low-grade metamorphosed volcano-sedimentary Malmesbury Group constitutes a complex, poorly understood supracrustal sequence that has been loosely subdivided into the Tygerberg, Swartland and Boland tectono-stratigraphic terranes by northwesterly trending fault zones. Syn- and post-tectonic granitoids of the Cape Granite Suite selectively intruded these terranes. Early S-types preferred the Tygerberg terrane whereas the later I-types dominate the remaining areas. Anorogenic A-type granites, however, occur in all three domains. Known metallization is directly or indirectly related to the intrusives, yet syngenetic deposits are conspicuously absent from the supracrustals. Four metal associations have been identified.• Cassiterite-wolframite (± Au, Cu, Mo, Fe-sulfides) in quartz and quartz/aplite veins hosted by tourmalinized and locally greissenized S-type granite. Similar exo-granitic veins occur in proximal metamorphites.• Juxtaposed disseminated, stockwork, breccia and vein style Cu-Mo-Fe-(Au)-sulfide mineralization hosted by mafic to intermediate intrusives of high K calc-alkaline, I-type affinity. • Cu-Mo-Au-sulfides hosted by hydraulic breccia pipes, stocks and veins occurring in anorogenic A-type alkali feldspar granites and amphibole quartz syenites.• Scheelite with minor Cu-Mo-sulfides and Au-associated with endo- and exo-skarns spatially related to I-type monzogranite, granite and alkali feldspar granite.The first three associations occur along the Yzerfontein-Helderberg-Zone, a 180 km lineament in the Tygerberg terrane, a zone exploited by syn-, late- and post-tectonic intrusives and their related mineralization. The fourth association is typical of the Boland terrane. The spatial and temporal relationships between the various metal associations is interpreted as the result of sequential intrusion of relative early high level S-type, followed by intermediate level I-type and finally anorogenic A-type granitoids during the evolution of a contracting continental margin arc and its irmer arc. This plate tectonic setting suggests subduction in an easterly direction underneath the Kalahari craton. The spatial configuration of the various terranes at the present erosional levels is the result of rifting and significant differential vertical displacement following cessation of subduction, a terminal tectonic event possibly synchronous with intrusion of the A-type granitoids.Near surface preserved roof zones and cupolas of both S- and I-type granitoids in the Tygerberg and Boland terranes, respectively, render these areas extremely prospective for Sn, W, Mo and Au mineralization. The presence of intermediate to mafic volcanics, a diversity of calcareous lithotypes and favorable plate tectonic setting of the Malmesbury Group suggest potential for the thus far elusive VMS, MVT and Sedex base metal and minor precious metal deposits."

Jan 1, 1994