Search Documents

By John Ramsay, Frederick A. Edwards, J. Eric Belford, Clarence V. Amyotte

"DEVELOPMENT of the underground mine is carried out from a main ramp driven from surface to the 800 and 1200 levels and from a shaft sunk to 3050 ft. Sub-levels at approximately 100-ft vertical intervals, starting 300 ft above the 800 level, were collared from the ramp as it advanced and a considerable amount of development work was pursued. The lateral and ramp work provided an opportunity to train drift crews, test equipment and methods, assess ground conditions and advance the initial stope development. The development of an exhaust ventilation raise system closely followed the extension of the level development to the south end of the orebody (Fig. 26) . On completion of the shaft, temporary lip pockets were installed at the shaft stations on the 800, 12.00, 1600, 2000 and 2400 levels. The permanent loading pocket had been installed on the 2860 level as part of the shaft-sinking contract and the level had been connected to the 2800-level station by a small muck transfer raise. Development of the 2800-level area was given top priority at this stage. This included a 1000-ft cross-cut to the crusher location, the crusher excavation, storage bins, conveyor ways and a ramp to connect the 2800 level to the loading pocket, the rope changing station and the shaft sump. The development and installation of the rock handling system between the 2400 level and the shaft bottom was contracted to Macisaac Mining and Tunnelling Company, of Sudbury, Ontario."

Jan 1, 1974

By W. H. MacLean, S. Liaghat

Abstract- The Key Tuffite is a thick (0.3 m to 6 m) and laterally extensive (-10 km) cherty, sulfide-bearing tuff unit in Archean greenstones in the Matagami mining district in northwestern Quebec. It lies at the contact of the Watson Lake Group and overlying Wabassee Group volcanic rocks, and is host to major Zn-Cu volcanogenic massive sulfide deposits. The tuff component is highly altered and its volcanic precursors are not identifiable by petrographie means. The tuff is mixed with a volcanic exhalative component comprising chert, carbonate and sulfides (pyrite, pyrrhotite, and minor sphalerite and chalcopyrite). The normative mineral composition of the Key Tuffite is 33% quartz, 28% sulfides, 16% sericite, 8% carbonate, 60Jo chlorite and 9% other minerals. In the vicinity of the Bell Allard and Orchan mines, the precursor tuff components are identified using immobile major and trace elements, as Watson Lake tholeiitic rhyolite (Zr/Y = 1.5 to 3.5, LaN/Ybn. = 1.7 to 2.8, Si02 = 72.5 ± 1.2 wt %, and Wabassee calc-alkaline andesite (Zr/Y =9, LaN/Ybn. = 4 to 8, Si02 = 56% to 65%). Immobile element computation techniques were used to calculate mass additions and losses in the conversion of the tuff to the Key Tuffite. Average net amounts of Fep3 (27% total iron), Si02 (14%), CaO (8%), S and K20 ( + 2%), were added, Na2O was removed (-2.8%), and MgO was over-all unchanged. Total net mass change was +63%, which comprises mainly exhalative additions, but also includes changes owing to hydrothermal alteration of the tuff component.

Jan 1, 1992

By R. Tomás, J. B. Serón, M. Romana

The Slope Mass Rating (SMR; Romana, 1985) geomechanics classification was developed as a sequel of Bieniawski’s Rock Mass Rating (RMR) system, which was almost impossible to use in slopes due to the extreme range of the correction factors (up to 60 points of a maximum of 100) and to the lack of definition of them. A detailed quantitative definition of the correction factors is one of the advantages of SMR classification. During the last thirty years the use of SMR system has been extended to many countries from the five continents and, thus, it is time to review the most interesting developments. Both RMR and SMR are discrete classifications, depending on the values adopted by the variables that control the parameters. This can cause major changes in the parameters value due to small differences in the variables value, with changes in the final rock mass assigned quality. On the other hand, geomechanics quality indexes are extremely biased. To avoid this problem, some authors have proposed continuous functions for SMR. This classification has been also adapted for its application in heterogeneous and anisotropic rock masses, for high slopes, for is application trough stereographic projection and Geographical Information Systems, has been used as susceptibility rockfall parameters and has been included in the technical regulations of several countries. Additionally, some open access computer tools have been developed for the computation of SMR. Consequently, this paper reviews: 1) the most important modifications and adaptations of slope classifications which derive directly from SMR; 2) the use of SMR throughout the world; 3) many significant papers on slopes analysed with SMR all over the world; and 4) future trends in the use of SMR.

Jan 1, 2015

By D. Knuutila, G. Goyette, James A. Finch, G. Bartolacci, A. Fortin, Chi Ho Lau, A. Lockhart

"In a COREM-McGill collaborative research and development project, gas dispersion parameters and froth properties were manipulated in a copper flotation plant to study interactions between the collection and the cleaning zones. In this paper, specific work on developing some relationships between operating conditions and froth stability in a rougher column flotation cell of 125 m3 is reported. Froth stability, measured by image analysis, was related to the following process conditions for specific flotation machines in an industrial case study: Gas flow rate, collector dosage, pH, frother type and dosage. Across the range examined, froth stability was improved through a decrease in gas flow rate and/or increasing frother dosage. Metallurgical results (grade and recovery) showed that both gold and copper were dependent on froth stability.INTRODUCTIONMcGill and COREM have over the past two years collaborated in a research and development project to merge gas dispersion parameters, frother analysis (McGill technology), and froth properties (COREM’s imaging system) to study the interactions between the collection zone (pulp) and the cleaning zone (froth). The main goal is to increase knowledge of flotation cell hydrodynamics since it is known to govern the metallurgical performance of the flotation process (Power et al., 2000). In this paper, specific work on developing some relationships between operating conditions and froth stability in a copper flotation circuit is reported.The objective of this work is to study gas dispersion in a large volume flotation column (hydrodynamics) and to measure its impact on the froth. By froth imaging, it is possible to diagnose operational problems on the basis of froth characteristics (Bartolacci et al., 2005a) and consequently, to propose ways of improving process performance by froth analysis (Bartolacci et al., 2005b).Another approach to froth characterization is investigated in this paper. In the same flotation column, a froth stability apparatus (column) was included (Triffet and Cillers, 2004). The mechanical froth stability apparatus is used to link “hard” froth characteristic measurements to “soft” froth characteristic measurements (those obtained by imaging)."

Jan 1, 2008

By C. M. Diaz, P. J. Mackey

Since its inception, in 1987, the Copper-Cobre series of conferences has established itself as the prime world forum for discussing advances in copper process metallurgy, in particular copper sulfide smelting, copper recovery by leaching and electrowinning and copper electrorefining. All copper producing countries have actively participated in the pyrometallurgy symposia held in the framework of these conferences. In 1999 and 2003, the close to 100 pyrometallurgy papers that were presented had to be accommodated in two volumes. In the present paper, the authors firstly provide a brief historical sketch of the Copper-Cobre conferences and then focus on providing a retrospective look at the dramatic changes that have taken place in copper smelting in the last few decades, primarily as discussed in the Copper-Cobre and precursor conferences pyrometallurgy proceedings. Topics include: the development of autogenous, increasingly more intensive, environmentally sound and energy efficient smelting processes; significant improvements in Peirce-Smith converting practice and at the same time the commercialization of alternative continuous converting routes; the consequent expansion and modernization of smelters; the increasing compliance with strict government environmental regulations in most copper producing regions of the world; the realignment of the copper smelting industry throughout the world; and trends in copper smelting R&D. A look at the future closes these reflections on the contribution of the Copper-Cobre conferences to the advancement of copper smelting technology.

Jan 1, 2007

By Da-Qiang Cang, Qingde Wang, Wei Wang, Wen-Bin Dai, Min Guo, Yu Li

Utilization of both slag and its heat for hot slag is a great challenge for iron and steel industry. Many methods of hot slag modification for directly converting hot slag into value-added materials were researched in recent years, and waste heat of hot slag could thereby be transformed into inner energy or chemical energy of the materials. In this paper, an experiment of converting hot slag directly into glass ceramics by hot slag modification method was conducted. A cooled modifiers mainly composed of fly ash were firstly heated though a cyclone furnace and then fell into a molten bath to mix with hot steel slag. Half of hot slag was used as raw materials and accordingly about half energy consumption, about 5MJ/kg for melting raw materials was saved in the process compared with that of traditional producing method. Frit quenched from the modified hot slag had a higher basicity of 0.6-0.7 than traditional frits in order to reduce the needed amount of cold modifiers and accordingly utilize more hot slag and its waste heat. Glass ceramics were further prepared from the frit and a heat treatment of one-stage method is more suiter to such frit than that of two-stage method. The glass-ceramics with basicity of 0.6 and heat-treated by one stage method had the best performance with bending strength of 146.46 MPa, Vickers hardness of 6.79 GPa, water absorption rate of below 2% and shrinkage rate of around 10%.

Jan 1, 2015

"10.1. IntroductionAs discussed by Westland (1981), the six platinum-group elements (PGE) belong to the Group VIII transition metals, to which iron, nickel and cobalt also belong. The chemical similarity between these nine metals accounts for the fact that they tend to be concentrated together as a result of geological processes. These processes started to effect the distribution of these metals at the very beginning of the earth's history.The first line in Table 1 gives the concentration of nickel and certain other Group VIII transition metals in carbonaceous chondrites, those meteorites with a composition that is believed to reflect best the composition of our planetary system apart from hydrogen and helium. The second line is the estimated concentration of the same elements in the earth as a whole. It is seen that these two estimates are quite similar, the earth being perhaps 2 to 3 times richer in these particular metals than the planetary system as a whole. The reason for this is not fully understood, but it may be due to the earth being formed by the accumulation and capture of a greater proportion of iron (and therefore siderophile-rich) than stoney (and therefore siderophile-poor) planetesimals than the planetary system itself.The third line in Table 1 is the average composition of the crust of the earth. With the exception of iron, all of the Group VIII transition elements are rare in the crust, present at concentrations of It tOO to Itt ,000 of that of the bulk earth. This is because the outstanding chemical characteristic of this group of elements is their siderophile nature; that is, their tendency to alloy with metallic iron. Because of this, once the earth became molten very early in its life history, these elements dissolved in the molten iron present at this stage and were removed from the outer accessible parts as this dense liquid sank to the centre of the earth to form the core. Although iron was the main instrument of concentration of the Group VIII metals, its much greater over-all abundance and its ability to combine with oxygen more easily than the others in the group means that significant amounts still remain in the oxidized portions of the earth.The fact that most of the Group VIII metals are available to use in workable concentrations at all is that they are 5 to 30 times more concentrated in the earth's mantle than the crust, as shown in line 4 of Table I. There has been a constant, if slow, interchange of matter between the mantle and the overlying crust throughout most of the earth's history and, under certain circumstances, this interchange has given rise to economic concentrations of metals."

Jan 1, 1979

By The Staff

"IntroductionThis paper lists typical liner performance data for various grinding mills at the Noranda, Waite-Amulet, Pamour, and Hallnor mines, and concludes with a comparison of these data, based on wear per square foot of lined mill shell area. Flow-sheets for each of these plants will be found in the reference cited.General InformationTwenty-eight ball-mills and one rod-mill are used by the Noranda organization for grinding ore. These mills, which are shown in general outline in Plate IV, are all of the overflow type and have a cylindrical shell attached to dished heads.Most of them are serviced by hand-operated cranes and none by power cranes. During re-lining, portable tugger hoists are employed to lift the liners and, frequently, to install them in place.The mills vary in length and diameter and the ratio of end liner area to breast liner -area consequently ranges from 1. 6.75 in a 5 ft. by 14 ft. mill, to 1:2.28 in an 8 ft. by 8 ft. mill."

Jan 1, 1950

By M. C. Pietrobon

"A common problem in assessing the applicability of laboratory flotation data is determining how closely conditions during laboratory testing of the ore matches those that occur in a plant. Typical laboratory based investigations do not consider factors such as water quality, pulp temperature and the pulp chemical environment during both grinding and conditioning on laboratory flotation performance. Disregarding these important factors may seriously compromise the validity of conclusions based solely on laboratory experimental results. Furthermore, considering these factors during the flowsheet design stage in the development of new ore resources may reduce financial risk associated with building a new plant. A methodology is described here which embraces these factors in an attempt to bridge the gap between laboratory and plant. The methodology should be considered a vital first step in all laboratory based experimental programs and has implications for fundamental studies on the flotation behaviour of single minerals. This methodology increases the confidence with which findings of laboratory based studies can be transferred to the plant and highlights the effect of variables which may be accessible to manipulation in the plant.Pulp chemical parameters, such as pulp dissolved oxygen demand, pH, Eh, mineral oxidation and solution composition were manipulated in the laboratory by adjusting the duration of gas purging after grinding, the process water input and pulp temperature. A key finding was that matching of the laboratory pulp chemistry to the plant pulp chemistry was dependent upon oxidation after grinding. In turn, mineral oxidation was dependent upon the pH in grinding, water composition and the duration of oxygen purging after grinding. The methodology closely matched the dissolved oxygen demand and surface chemistry of laboratory and plant pulps."

Jan 1, 2002

By Manqiu Xu, Songtao Yang, Zongfu Dai, Robert Pelton, Carla Abarca

"Fine mineral particles are difficult to process by flotation because of their low collision efficiencies with air bubbles. Decreasing air bubble size and increasing mineral particle size through flocculation are the most common approaches to improve flotation efficiencies. Herein we demonstrate that nanoparticle flotation collectors can be engineered to selectively induce fine mineral particle aggregation and promote flotation.Flotation tests of clean fine pentlandite (Pn) and Clarabelle Mill (CBM) rock tails and pyrrhotite (Po) tails that contained significant amount of fine pentlandite have confirmed that the nanoparticles can serve as both collectors and selective flocculants for fine pentlandite. In the case of clean fine Pn, the nanoparticle collectors virtually can float almost all Pn fines. Scoping tests on CBM tails have shown significant improvement in nickel recovery. Addition of nanoparticles as a flotation aid can recover 20% of the nickel contained in the rock tails and 40% of the Pn contained in the Po tails compared to current mill operations giving 0% nickel recovery from rock tails and no Pn selectivity from Po tails. Ongoing work includes attempts to identify optimal strategies for employing nanoparticles in fines flotation.IntroductionFine particle flotation is an industry-wide challenge in mineral processing. Fine mineral particles are difficult to process by flotation because fine particles have low mass and thus low momentum, which results in their low collision efficiency with air bubbles (Dai, Fornasiero, & Ralston, 1999). In addition, fine particles have not only high specific surface area but also more active surface area, which causes high reagent consumption. For base metal sulphide minerals, particle size between 10 µm and 70 µm is a typical range where high flotation recoveries can be achieved with conventional flotation chemistry and acceptable cell residence times. For pentlandite, the flotation recoveries decrease sharply when the particle size is below 10 µm and hydraulic entrainment is the dominant mechanism, giving recoveries proportional to water recovery and no Pn enrichment. (Jameson, Nguyen, & Ata, 2007)"

Jan 1, 2015

By A Walker

The presence of high noise levels in many industries, together with the fact that countries are becoming increasingly concerned with the health of its citizens, has contributed to the importance of the problem of hearing loss. This problem has become the focus of scientific research, law and medicine, and the object of this thesis is to present the means whereby noise may be detected, with its resulting effects and possible means of control, in mining operations. 0BJECTIONABLE noise is a particularly prevalent by-product of the mining industry, and, al-though a dangerous noise level has been recognized, it is believed that at no time now, or in the future, will it be possible to enumerate a single over-all decibel figure at which hearing impairment will oc-cur. Individual susceptibility must be recognized in any study of occupational loss of hearing aimed at the setting of standards and criteria for industrial noise control.

Jan 1, 1963

By Olaf Kessler, Jan Kalich, Michael Reich, Julia Osten, Uwe Füssel

Modern automobile bodies consist of different materials, e.g. aluminium alloys and high strength steels. Mechanical joining, e.g. clinching, is very suitable for joining aluminium and steel sheet. But clinching needs a sufficient ductility, which is no longer supplied by high strength steels. Laser-assisted clinching has been shown, to be able to join aluminium and high strength steel sheet successfully. Thereby the steel sheets were heated locally for short times to increase their ductility. Due to the thermal contact between steel and aluminium sheet the aluminium alloys also achieve a local short-time heat treatment. This fact may cause a significant impact, as aluminium sheet in automobile bodies is often used in T4 (or similar) condition and later artificially aged during the paint bake cycle. Aluminium alloys 6016 and 6181 have been short-time heat treated with heating rates up to some 100 K/s. Precipitation and dissolution processes have been monitored in-situ by calorimetry. Mechanical properties have been investigated on as well as after short-time heat treatment by deformation dilatometry. The results show, that suitable short-time annealing parameters during laser-assisted clinching can increase ductility and at the same time act as retrogression for aluminium sheets, resulting in increased strength after aging.

Jan 1, 2015

By Lori Kormos, Jhonny Carrión De la Cruz, Dominic Fragomeni, Elizabeth Whiteman, Jorge Oliveira

"Process diagnosis, flowsheet design and optimisation are most effectively and efficiently achieved through the use of metallurgical testwork combined with more modern quantitative mineralogical techniques. Integration of the mineralogical data in testwork programs provides a resolution that cannot be obtained from assays alone and can direct the flow of work to result in optimized conditions more quickly than would otherwise be possible. At Xstrata Process Support (XPS), QEMSCAN (Quantitative Evaluation of Materials by Scanning Electron Microscope) and EPMA (Electron Probe Micro Analyser) information can be employed to diagnose specific issues in a plant or lab scale test and are routinely combined with other metallurgical data sets to benchmark performance, design and optimise flowsheets. Representative sampling protocols for ore bodies or test products, the use of geometallurgical unit classification and high confidence metallurgical test programs are key components of the strategy. Two case studies from Xstrata Zinc’s Antamina Mine and Concentrator in Perú, and Xstrata Nickel’s Nickel Rim South Mine in Sudbury are described to show how the use of quantitative mineralogy were used to diagnose a plant issue and how the data can be integrated into metallurgical programs to assist mineral processing engineers to design and optimise flowsheets.INTRODUCTIONOver the past decade, there has been a shift away from metallurgical testing that employs only chemical assays to quantify performance; the use of empirical observation in order to optimise a flowsheet; and the extraction of bulk samples for testing or piloting. The integration of geological information into the planning and execution of testwork programs including the use of quantitative mineralogy has improved the overall quality and predictability of metallurgical programs. At the same time, improvements to metallurgical testwork protocols such as rigorous statistical assessment of results, the use of factorially designed experimental strategies (DOE), and replicate flotation with appropriate quality controls, has improved the confidence level in these results.Process diagnosis, which utilizes quantitative mineralogy, can clearly define the root cause of the metallurgical issue. Whether used on its own to diagnose an issue or in combination with other metallurgical testwork, the use of mineralogical data has become the standard in the mining industry."

Jan 1, 2010

The construction, commissioning and operation of a continuous pilot-scale selective agglomeration (oil agglomeration) unit are described. This plant has been used to recover fine coal from an effluent stream that is produced by a jig plant which scalps the coal from a New South Wales (Australia) colliery. The reject slurry is extremely fine (66.5% minus 53 um) and has an ash content of approximately 40%. The pilot plant can treat up to 0.3 tonne/h of this slurry, producing average product ashes as low as 9.1% and tailings ashes greater than 80%. The average yield observed was62%, which corresponded to a recovery of coal material of 88%. The operation of this pilot plant yielded data that enabled an economic assessment of this type of processing to be carried out. This study showed that selective agglomeration is an economically viable process for eliminating the substantial losses of coal to tailings ponds and minimizing consequent disposal and environmental problems. A commercial plant has been constructed and commissioned on the basis of the data obtained from this pilot-scale operation.

Jan 1, 1979

By Michel Rodrigue, Sylvain Duchesne, Louis Racine

"LocationThe Louvicourt mine is located 20 km east of Val d'Or in Abitibi, in the northwest part of the province of Quebec. The mine is located on Highway 117 connecting Val d'Or to Montreal and very close to the main railway networkHistoryFive successive exploration attempts by Aur Resources resulted in the discovery of the large Louvicourt orebody in June 1989. Construction of the surface and underground infrastructures commenced in the spring of 1991. Milling operations commenced in July 1994. The entire project cost CDN$290 million, almost CDN$20 million less than initially estimated. The concentrator infrastructure cost CDN$64 million.Louvicourt mine is owned in partnership by Novicourt Inc. (45%), Teck Corporation (25%), and Aur Resources Inc., the administrator (30%).Brief DescriptionLouvicourt mine is the largest producer of base metals (Cu and Zn) in Abitibi-Temiscamingue. Its average daily production is nearly 4300 t of ore, for an annual production of 200 000 t of copper concentrate (28% Cu) and 33 000 t of zinc concentrate (57% Zn). After only a few weeks of operation, it had attained its objectives for the most part, and operations continue to be improved."

Jan 1, 2000

By S. Dessureault, J. Porter, M. Woodhall

Information and communication technology (ICT) is seen as a key source of future productivity improvements in mines. The information technology infrastructure (ITI) necessary to achieve these productivity improvements will come in the form of data integrated from multiple source systems throughout the mining value chain. Two pure approaches are available: supplier-controlled or operations controlled data structures; each strategy has its own advantages and disadvantages. Case studies involving the South African mining industry are used to demonstrate the advantages of using hybrid-controlled data structures. Depending on the level of operational control, new skills are also necessary to be learnt by mining professionals including: information engineering; creating consistent and quality data; and process improvement techniques that use the integrated data for improving the operation.

Jan 1, 2004

By W. G. Miller

An overall study was conducted to evaluate the properties and processes influencing the rate and magnitude of consolidation for oil sands fine tailings produced using different extraction processes. As part of this overall study, consolidation tests using slurry consolidometers were carried out for caustic and non-caustic fine tailings. The influence of a change in bitumen extraction process (caustic versus non-caustic) on consolidation properties, namely compressibility and hydraulic conductivity, was determined, as was the effect of adding a coagulant (calcium sulphate [CaSO4]) to caustic fine tailings. For fine tailings originating from two different oil sands ores (Ore A and Ore B), results were presented in terms of variation in average void ratio with time (settlement), void ratio with effective stress (compressibility), hydraulic conductivity with void ratio and coefficient of compressibility and hydraulic conductivity with sodium adsorption ratio. Findings indicated that chemical characteristics of fine tailings (water chemistry, degree of dispersion) do not have a significant impact on their compressibility behaviour and have only a small influence at high void ratio (low effective stress). The biggest advantage of non-caustic fine tailings and treating caustic fine tailings with coagulant is an increased initial settlement rate and slightly increased hydraulic conductivity at higher void ratios. Thereafter, compressibility and hydraulic conductivity is governed by effective stress.

Aug 1, 2010

By W. G. Miller, J. D. Scott, D. C. Sego

An overall study was conducted to evaluate the properties and processes influencing the rate and magnitude of consolidation for oil sands fine tailings produced using different extraction processes. As part of this overall study, consolidation tests using slurry consolidometers were carried out for caustic and non-caustic fine tailings. The influence of a change in bitumen extraction process (caustic versus non-caustic) on consolidation properties, namely compressibility and hydraulic conductivity, was determined, as was the effect of adding a coagulant (calcium sulphate [CaSO4]) to caustic fine tailings. For fine tailings originating from two different oil sands ores (Ore A and Ore B), results were presented in terms of variation in average void ratio with time (settlement), void ratio with effective stress (compressibility), hydraulic conductivity with void ratio and coefficient of compressibility and hydraulic conductivity with sodium adsorption ratio. Findings indicated that chemical characteristics of fine tailings (water chemistry, degree of dispersion) do not have a significant impact on their compressibility behaviour and have only a small influence at high void ratio (low effective stress). The biggest advantage of non-caustic fine tailings and treating caustic fine tailings with coagulant is an increased initial settlement rate and slightly increased hydraulic conductivity at higher void ratios. Thereafter, compressibility and hydraulic conductivity is governed by effective stress.

Jan 1, 2010

By Philip J. Guerney, S. O’ Leary, André R. Laplante

"Concentration of dense mineral phases (s.g. greater than 7) for characterisation of individual particles and mineral grains by electron microscopy is a well established technique for the detection and characterisation of valuable mineral phases. This presentation describes the type of data that can be generated when both the concentration and characterisation steps are carried to higher levels than typical. The concentration step is the gravity recoverable gold (GRG) protocol that has been used for over 100 ore samples. This protocol yields three concentrates that represent three progressive degrees of grinding and liberation. Three ore samples were subjected to the GRG protocol and three size classes of each concentrate were characterised using the mineral liberation analyser (MLA), an automated, EDX-based tool. This presentation briefly presents GRG and MLA technology, and then focuses on the results obtained: photos, images and databank, the latter used to evaluate the extent of particle liberation and particle shape.INTRODUCTIONThe practice of gravity concentration prior to characterization of mineral samples using electron beam microscopy is solidly established. Typically, a dense liquid such as tetrabromoethane (density: 2.97 g/cm3) is used to reject the light phase, typically carbonates and silicates. The heavy phase, mostly sulphides, oxides and precious metals, is then mounted in a polymer matrix and examined using beam microscopy.Both the pre-concentration and the sample preparation/examination steps have seen significant advances over the past ten years, but are not without problems. A major issue of preconcentration is that most dense liquids used are toxic, tetrabromoethane being a prime example. More recently, a dense liquid with little or no toxicity (sodium polytungstate, distributed by Sometu Inc.) has become commercially available, but its use is limited to relatively low s.g. splits around 3 g/cm3. Dense liquids are viscous, and their use is limited to particles coarser than 37 µm, although centrifuge separation can probably lower this limit to around 10 µm. Magnetogravimetric separators can achieve much higher specific density cuts, but upgrading below 100 µm or in the presence of magnetic minerals remains a problem. The use of centrifuge separators such as the 3-in Knelson Concentrator (KC MD3) or the Falcon 4-in SB (SB4) is particularly attractive since these units can easily process large masses (by laboratory standards) and achieve a cut density well above those of dense liquids."

Jan 1, 2003

By R. P. van Hille, A. W. van Zyl

The BIOX® culture, aiding liberation of arsenopyrite/pyrite occluded gold, is inhibited by thiocyanate (SCN > 1 mg/L); precluding the recycling of tailings water up-stream of the bioleaching circuit. The activated sludge tailings effluent remediation (ASTERTM) process is a biological process that was developed to facilitate water recovery and treat waste water on-site (to achieve a SCN concentration < 1 mg/L) to be recycled or disposed of. The aim of this study was to investigate the effects of changing temperature and SCN loading on the SCN degradation ability of the mixed microbial population clue to seasonal temperature changes and fluctuations of SCN concentration in the waste water.

Jan 1, 2011