Search Documents

By S. Kodama, G. Sasaki, K. Matsugi, K. Sugio, Y. B. Choi

"Pure aluminum (Al) matrix composites with changing the volume fraction of TiB2 particle content from 10 to 30% was fabricated by spark plasma sintering (SPS) process. Then the microstructure, density, dispersibility and thermal conductivity of the composites was estimated. As increasing TiB2 content, the dispersibility of particles and the density of the composites degraded slightly. And, the effect of the dispersibility of TiB2 particles on the thermal conductivity was quite little. The thermal conductivity of the composites was less than the theoretical value calculated by Maxwell-Eucken equation considering the effect of the density. It is due the influence of the interface heat transfer rate, because these composites have many small sized particles and have high interface density.INTRODUCTION Recently, metal matrix composites (MMCs) have been used widely in electric / electronic components, architectural materials, transportation equipment, aerospace and a precision instruments, because it’s superior properties have been greatly watched. Demand of MMC for industrial use has been increasing gradually. Furthermore, multifunction properties are required for the composites strongly. By integrating the dissimilar materials, the composites have various properties that we cannot get from monolithic materials. On the other hand, the response to the thermal management is required for materials, recently, and the need for the structural material controlling the thermal conductivity has been increasing. Especially, superior thermal conductivity and good mechanical properties from room temperature to high temperature are required for heat sink and heat exchanger at the same time. In late years, a study on the composites combining carbon materials and aluminum and copper has been developing, and actually the composites with high thermal conductivity which is not provided in the conventional materials is developed. On the other hand, non-oxide ceramics particles such as SiC and AlN, TiB2 have good thermal conductivity. Particularly, as TiB2 has good electrical conductivity, TiB2 containing MMCs is expected as innovative materials used as electric/ electronic components. Furthermore, as TiB2 has low density, high melting point, low thermal expansion and good deformation resistance, the development of high performance composites with multi-functional properties is expected. As thermal conductivity of pure Al and TiB2 are 225 and 66.4 W/mK, respectively, it is expected that the degradation of thermal conductivity by adding dispersant in Al matrix is suppressed. The authors have carried out a thermal conductivity, electrical conductivity, mechanical properties of 20 vol.% TiB2 dispersed Al composites (Sugio, 2016, Sasaki, 2016). In this study, the influence of quantity of addition of TiB2 on microstructure, thermal conductivity was studied minutely."

Jan 1, 2018

By J. Manchisi

This study has investigated the use of blast furnace slag as functional adsorbent for metal ions in acid mine drainage treatment. This opportunity has not yet been developed into a practical process partly because of limited understanding of rates and mechanisms of adsorption process and inconsistency in interpretations of adsorption data. The overall objectives were to determine the efficiency and mechanisms of sorption process of metal ions in a multiadsorbate system. We employed standard materials characterisation techniques to analyse composition, structure and surface morphology of the slag. Batch adsorption experiments were then conducted to study the mechanisms, kinetics and efficiency of metal sorption as a function of pH, phase ratio, mixing time, mass and particle sizes of slag. Both XRF and adsorption data suggested the slag to possess acid neutralising capacity. This slag is non-crystalline based on XRD pattern, has adequate porosity and pore volume comparable to similar commercial adsorbents but it has inferior pore structure, pore size distribution and BET surface area to be effective under wide applications. Metal sorption increased with decrease in slag particle diameter, decrease in initial metal concentration and increase in the mass of slag. Although slags have demonstrated to efficiently treat low concentrations of single and multiadsorbate effluents using fine particle sizes, they have limited capacity to treat multiadsorbate systems for some metal ions. This is probably due to low affinity, competitive adsorption or limitation in material?s adsorptive properties. Sorption mechanisms probably involve precipitation and ion exchange on the basis of alkaline pH and exchangeable slag surface ions. Sorption preference is proposed as Fe2+>Cu2+>>Cd2+>Co2+>Mn2+. Despite these limitations, deeper understanding of sorption behaviour of metal ions by slags for application in dilute and large volumes of effluents is necessary where precipitation and other standard techniques are either inefficient or uneconomic. Thus, this study has established that sorption capacity of slag to remove metal ions from acidic effluents is selective, limited to certain metal ions and for other ions only at low concentrations. Further adsorption studies in multiple solutes under various experimental conditions or those that can propose an economic slag activation process are needed that improves or widens adsorption window.

Aug 1, 2013

By T. Boiselle, C. Gielen, P. Henry, J. M. Bier

"Hydrometal is specialized in the production of zinc sulphate from complex secondary raw materials. Electric Arc Furnace (EAF) dust is one of the more interesting potential sources to produce zinc sulphate. In order to minimize waste quantities generated from EAF dust treatment, our R&D team has developed and patented a new process to recover the Fe contained in the dust as iron oxide product to be used and sold into the pigment market. The process is based on a specific reductive leaching step of the zinc ferrite contained in EAF dust, followed by a purification step to remove impurities (Ni, Cr, Cu...) and finally the controlled precipitation of the iron oxide. The aim of the iron precipitation step is to obtain the right shape and length of crystals in order to guarantee the right color and tinting strength of the pigment. The innovative aspects of the process results in the controlled oxidation of the iron to get the right crystal size and good purity material. The iron product can be valorized as red or yellow pigment often produced by the Penniman-Zoph process.INTRODUCTION A Few Words about HYDROMETAL Hydrometal SA (Engis, Belgium) is a subsidiary of Jean Goldschmidt International SA (JGI) in Brussels. JGI is mainly involved in metal trading activities (Goldschmidt, 1995). In 1985, JGI acquired the leaching circuit of a Belgian electrolytic zinc producer located in Engis, a few kilometers south of Liège, near the river Meuse and it was decided to name this plant: SA HYDROMETAL. Hydrometal is well connected by water, rail and road from its central location in the industrial region of Liege, in the heart of Europe. The company received in 1997 an additional license to process and recycle toxic and hazardous waste. Figure 1 shows a picture of the plant."

Jan 1, 2016

By Wouter Bleeker, Isabelle Cadieux

"Abstracts of theses related to mineral deposit studies and exploration, completed at geology or earth science departments of Canadian universities, have been compiled for the period 1991 to mid-I993. Part I, presented in the June, 1994 issue of the ClM Bulletin, gave a listing of thesis titles. Part II, which consists of edited abstracts of theses considered to be of direct application to mineral deposit studies and exploration, is presented under various themes as follows:A. Kimberlites, Other Alkaline Intrusions and Related Studies;B. Volcanogenic Massive Sulphide Deposits and Related Studies;C. Mineral Economics;D. Mesothermal Gold Deposits, Other Gold Deposits and Related Studies;E. Magmatic Nickel-Copper, Platinum Group Element, and Chromite Deposits and Miscellaneous Platinum Group-related Studies;F. Granite and Pegmatite-related Deposits and Porphyry Deposits;G. Diverse Hydrothermal Deposits. Sediment-hosted CopperDeposits and Mississippi Valley Type Lead-Zinc Deposits; andH. UranitnlHeiated studies, Evaporites and Exploration Geophysics.Abstracts related to themes A to D were presented in previous issues of the ClM Bulletin, abstracts related to themes E and F are presented in this issue. The remaining abstracts will be presented in a future issue."

Jan 1, 1994

By H. L. Gibson, T. N. Setterfield, J. J. Watkins, R. W. Hodder

"The McDougall-Despina fault set in the Noranda district of northwestern Quebec defines the eastern margin of the Despina cauldron, nested within the district-scale Noranda cauldron. The faults are stratabound in that they displace stratigraphy of the cauldron fill, but do not off-set the cauldron cover. The faults are occupied by dikes that acted as eruptive centers to volcanic members of the cauldron-filling sequence. Measurable displacement across the McDougall-Despina fault set is greater than 750 m, and coincident with post-cauldron volcanism. Feeder dikes cross-cut each other and are typically depleted in Na2O and CaO, and enriched in MgO, K2O, Fe2O3and MnO relative to fresh flows. Economic and subeconomic massive sulfide deposits occur adjacent to the McDougall-Despina fault set at different levels over a stratigraphic thickness of 3000 m. These include the Corbet deposit, the subeconomic D-68 Zone deposits, and the subeconomic stringer zones of South Rusty Hill and Bedford Hill. Numerous copper occurrences and abundant hydrothermal alteration occur in and immediately adjacent to the fault set.The McDougall, Despina, and adjacent, parallel, ancillary faults define a synvolcanic fault set which controlled the location of magmatism, hydrothermal alteration and mineral deposition during the early evolution of the Noranda cauldron. Significant sulfide mineral deposition commonly occurred in proximity to the intersection of the McDougall-Despina fault set with northeast-trending synvolcanic faults. Recognition of synvolcanic faults is therefore a major objective of exploration programs for volcanic-associated massive sulfide deposits."

Jan 1, 1995

By A. J. W. Law

"This paper deals with the organization of the central office technical areas and the role played during the feasibility studies, construction and operating phases of Les Mines Selbaie.HistoryThe Engineering Department was originally formed as a part of the Exploration Department, to examine the feasibility of advanced exploration prospects being brought to the company. In 1968, with the discovery of the South Bay property in northwestern Ontario, the department became part of a Mining Division and was expanded, so that it could provide more advanced mine feasibility studies, control of construction engineering and procurement and initial mine design. As is generally the case, the mine design function was handled with in-house capability, while plant, mill and const ruction functions used outside consultants.The 1974 discovery of the Selbaie deposits, started a period o f growth in the capabilities o f the department. The complex nature of these deposits, required that skills were added in the mining, metallurgical and plant areas. During the early feasibility study period these skills were provided by the engineering company of the parent group, but when it was realized that production from the deposits was likely, permanent staff was added."

Jan 1, 1990

By H. L. Gibson, T. N. Setterfield, J. J. Watkins, R. W. Hodder

"Abstract - The McDougall-Despina fault set in the Noranda district of northwestern Quebec defines the eastern margin of the Despina cauldron, nested within the district-scale Noranda cauldron. The faults are stratabound in that they displace stratigraphy of the cauldron fill, but do not off-set the cauldron cover. The faults are occupied by dikes that acted as eruptive centers to volcanic members of the cauldron-filling sequence. Measurable displacement across the McDougall-Despina fault set is greater than 750 m, and coincident with post-cauldron volcanism. Feeder dikes cross-cut each other and are typically depleted in Na2O and CaO, and enriched in MgO, K2O, Fe2O3 and MnO relative to fresh flows. Economic and subeconomic massive sulfide deposits occur adjacent to the McDougall-Despina fault set at different levels over a stratigraphic thickness of 3000 m. These include the Corbet deposit, the subeconomic D-68 Zone deposits, and the subeconomic stringer zones of South Rusty Hill and Bedford Hill. Numerous copper occurrences and abundant hydrothermal alteration occur in and immediately adjacent to the fault set.The McDougall, Despina, and adjacent, parallel, ancillary faults define a synvolcanic fault set which controlled the location of magmatism, hydrothermal alteration and mineral deposition during the early evolution of the Noranda cauldron. Significant sulfide mineral deposition commonly occurred in proximity to the intersection of the McDougall-Despina fault set with northeast-trending synvolcanic faults. Recognition of synvolcanic faults is therefore a major objective of exploration programs for volcanic-associated massive sulfide deposits."

Jan 1, 1995

By Tyson C. Birkett

Initial indicator mineral sampling covering 425,000 square km of northern Quebec and subsequent follow-up of positive results convinced the Ashton ? SOQUEM joint venture to acquire mineral rights to 380,000 hectares prospective for diamond in late summer, 2000. Drilling in 2001 and 2002 identified eight kimberlitic bodies, all significantly diamondiferous. Commercial size stones (retained on a square mesh sieve with openings 0.85 mm) and encouraging grades have been returned by several bodies tested to date: The Renard bodies are formed by steep-sided breccia pipes with kimberlitic matrix surrounded by irregular outboard breccia zones within country rock. These bodies were emplaced in high-grade metamorphic rocks of the Superior Province of Archean age. Orthogneiss with lesser tonalite hosts the breccias, although regionally paragneiss is also present. Diatreme facies portions and nearby country rock are intruded by minor to major (Renard 1) amounts of hypabyssal-facies kimberlitic rock. Renard bodies are macrocrystic, with large olivine crystals set in a groundmass of olivine, phlogopite, monticellite, spinel, carbonate, apatite and serpentine. Proximity of various Renard bodies, with most in a core area of 0.5 square km will allow planning of an efficient mining operation. Geophysics, especially magnetic surveying, has contributed to identifying bodies of kimberlitic rock.

May 1, 2003

By K. Thuro, L. Wilfing, H. Kasling

"In mechanized tunneling, performance prediction is a crucial issue for estimating excavation costs and construction time of a tunnel project. The aim of this work is to compare the calculated parameters by penetration prediction models with the results of penetration tests during excavation by a Tunnel Boring Machine (TBM) at actual tunnel projects. This comparison helps to improve the existing prediction models (Gehring, 1995 and Rostami (Colorado School of Mines), 1997.) and to develop a new, so-called “Alpine Model” (research group ABROCK; Schneider et al., 2012).On-site penetration tests are a common tool to determine performance of a TBM in certain geological environments. During a test, the TBM is operated under defined conditions that allow comparing the results of different projects and machine types. There are two different types of penetration tests in use. The more common type, described by Bruland (1998a), is based on test drives at different thrust levels. The tests in this study are performed as start-stop-tests, meaning that the TBM starts from zero to the maximum possible thrust and reverse with slowly increasing respectively decreasing steps (Frenzel et al., 2012). To gain information about the interaction between TBM and rock mass, a detailed geological documentation including an analysis of the discontinuity pattern and laboratory testing for rock strength characterization are mandatory.Within the last year 16 penetration tests have been performed. The results are thrust- penetration curves (Figure 2) showing that up to a certain penetration rate only crushing occurs (subcritical penetration). From there the desired rock fragmentation process called chipping takes place (Frenzel et al., 2012). These two different fragmentation processes can be described best by a bilinear function as seen in Figure 3. Both, CSM- and Gehring-model, do not fit to the trend of the penetration rates determined during the excavation process as they are using potential or simple linear functions.Another parameter that has to be implemented into the new prediction model is the influence of discontinuities. In case of favorable orientation and spacing, discontinuities reduce the required thrust at same penetration rates. In contrast, unfavorable discontinuity systems can cause blocky faces and hence worse performance than predicted. Besides discontinuities, the toughness of rocks has to be taken into account when predicting the penetration as tough rocks need more energy to obtain complete failure than brittle rocks.Key advantage of these tests in comparison to existing are more data points in less time. By improving respectively extending the existing penetration prediction models with the stated parameters, the penetration prediction for TBMs can be more accurate and also wear calculation can benefit from this approach."

Jan 1, 2015

By T. Sun, J. Kou, C. Sun, China Railway Resources Group Limited

"The polymetallic sulfide ore in Jiama county of Tibet contains 0.78% Cu, 0.046% Mo, 0.31 g/t Au and 17.9 g/t Ag in average. However, heavy loss of valuable metals was observed using high-pH process and Butyl xanthate as the collector. In this paper, the flotation was optimized through the adoption of a novel collector C-7, which is a mixture of xanthate ester and thionocarbamate. This collector showed better flotation performance under weak base conditions. The recoveries of Cu, Mo, Au and Ag increased to 93.24%, 84.60%, 78.13% and 75.41%, respectively, under 15 g/t of C-7 at pH of 8.0. The adsorption mechanism of C-7 was investigated by micro-flotation tests, zeta potential measurements, FTIR analysis and adsorption quantity measurements. Chemisorption of C-7 on chalcopyrite surface is demonstrated with adsorption density 3.8 times higher than on pyrite.INTRODUCTIONXanthates are the most commonly used collectors of strong collecting ability for separating copper sulfide minerals from gangue in froth flotation. However, the selectivity of xanthates themselves is poor to realize separation of chalcopyrite and pyrite whose floatability are quite similar (Heyes & Trahar, 1977; Chandraprabha, Natarajan, & Modak, 2004). High pH process with xanthates as collectors is proved effective in copper-sulfur separation and is widely used in treatment of copper sulfide ore flotation (Smith, 1996; Valdivieso, Cervantes, Song, Cabrera, & Laskowski, 2004). This method could get ideal separation results, but large amount of lime must be added, and could bring about increased cost, device corrosion and environmental pollution. In addition, there could also be high depression and heavy loss of associated noble metal such as Mo, Au and Ag. Consequently, a large amount of research has been conducted on substitutions of xanthates for selective flotation of copper sulfide ores under low pH conditions (Gholivand, Khodadadian, & Ahmadi, 2010; Li, 2010)."

Jan 1, 2016

By André Chagnon, Michel Malo, Benoît Dubé, Chantal Pelchat

"Abstract- In the southern Gaspé Appalachians, gold mineralization is spatially associated with the Acadian dextral strike-slip Grand Pabos-Restigouche fault system. Two different structurally-controlled gold prospects, the Lac Arsenault and the Saint-André-de-Ristigouche, are described to unravel the genesis of gold mineralization in this part of the Canadian Appalachians.At the Lac Arsenault gold prospect, gold mineralization consists of Au-As-Pb-Zn-Cu-(Ag) polymetallic fault-filled quartz veins with laminated textures emplaced in brittle-ductile sinistral X shear fractures. Mineralized veins are hosted by Middle Ordovician graywacke of the Arsenault Formation, belonging to the Dunnage Zone, the Early Paleozoic oceanic domain of the Appalachians. Terrigeneous rocks of the Arsenault are regionally metamorphosed at the lower greenshist facies and the mineralized veins are included in a zone of Fe-carbonate alteration.The Sb-Au-As mineralization of the Saint-André-de-Ristigouche gold prospect, in the southwestern Gaspé area, comprises extension veins in the extension direction emplaced in brittle conditions. Mineralized veins are hosted by calcilutite and laminated silty and argillaceous limestone of the Early Silurian part of the White Head Formation, which belongs to the Gaspé Belt, the Middle Paleozoic successor basin in the Gaspé Appalachians. Metamorphic grade of the White Head Formation in the southwestern Gaspé area is very low, but the gold mineralization is included in a zone of hydrothermal propylitic alteration which includes two Cu-skarn mineral occurrences. The Lac Arsenault gold prospect has many characteristics of "greenstone-hosted quartz-carbonate vein" deposits whereas the southwestern Gaspé area, which includes the Saint-André-de- Ristigouche gold prospect, shows affinities with the geological setting of sediment-hosted gold deposits (Carlin-like deposits). The two gold prospects are controlled by the Grand Pabos- Restigouche fault system but they were not emplaced at the same level in the crust. Acadian strikeslip fauting played a major role in their respective genesis in providing channelways for ore-bearing fluids. The recognition of the analogy of the geological setting of the southwestern Gaspé area with that of Carlin-like mineralization gives new ideas for exploration in the area and elsewhere in the Appalachians.Résumé - Dans le sud des Appalaches de la Gaspésie, on trouve des minéralisations aurifères spatialement associées au système de failles de coulissage dextre acadien de Grand Pabos-Restigouche. Deux indices très différents, Lac Arsenault et Saint-André-de-Ristigouche, sont décrits pour évaluer la genèse des minéralisations aurifères à contrôle structural de cette partie des Appalaches canadiennes. Au Lac Arsenault, la minéralisation aurifère comprend des veines polymétalliques à Au-As-Pb- Zn-Cu-(Ag) en remplissage de failles. Ces veines à texture laminaire se retrouvent dans des zones de cisaillement fragiles-ductiles senestres de type X. Les veines minéralisées sont encaissées dans les grauwackes d’âge Ordovicien moyen de la Formation d’Arsenault appartenant à la zone de Dunnage, le domaine océanique du Paléozoïque précoce des Appalaches canadiennes. Les roches terrigènes de l’Arsenault sont métamorphisées régionalement au faciès inférieur des schistes verts et les veines aurifères sont dans de larges zones d’altération dolomitique (Fe-carbonate).Dans le sud-ouest de la Gaspésie, la minéralisation à Sb-Au-As de Saint-André-de-Ristigouche est dans des veines d’extension comprises dans la direction d’extension et mises en place dans des conditions de déformation fragile. Les veines minéralisées sont encaissées dans les calcaires argileux et les calcilutites de la partie silurienne de la Formation de White Head qui appartient à la ceinture de Gaspé, le bassin successeur du Paléozoïque moyen des Appalaches de la Gaspésie. Le degré métamorphique des roches du White Head est très bas, mais"

Jan 1, 1998

By P. Mottahed, J. Ran

Mining practice and research have shown that the jointed roof in stratified rock behaves like a voussoir beam structure with strength greater than that determined by the continuous beam theory. Previous studies have demonstrated the voussoir beam mechanism and developed methods to estimate the crushing and buckling strength of voussoir beams. However, research on voussoir beams with multiple mid joints has not been suffICient and problems such as the voussoir beam support and applications of the voussoir beam mechanism to the mining environment have not been addressed. In this paper, mechanism of voussoir beams containing multiple mid joints and truss support are studied and applications of the voussoir beam mechanism to underground mine openings are discussed based on the numerical and experimental results.

Jan 1, 1995

By J F. Davies

A review is presented of the fundamental differences between the Superior and Churchill geologic provinces. Structure, lithology, grade of metamorphism and a single recent age determination suggest that the Flin Flon -Snow Lake and Lynn Lake belts are remnant blocks of originally Superior rocks lying within the Churchill province. Major mineral belts occur along the main boundary between the Superior and Churchill provinces (the Thompson -Moak Lake nickel belt) and within the remnant Superior blocks inside the Churchill province (Fiin Flon -Snow Lake and Lynn Lake). During the Hudsonian orogeny, metamorphic gradients must have existed across the Churchill-Superior boundary and between the remnants of Superior rocks and the enclosing gneisses of the Churchill province. It is possible that not only the unusual nickel deposits of the Thompson belt but also the base metal deposits of the Flin Flon -Snow Lake and Lynn Lake districts are due to redistribution, or diffusion and migration of metals to areas of lower-grade metamorphism during the Hudsonian orogeny.

Jan 1, 1964

By A. A. Rogozhin, E. G. Likhnikevich, S. I. Anufrieva, A. V. Kurkov

The Beloziminskoe deposit in Siberia is a large, potentially productive deposit of rare metals contained in ochreous apatite pyrochlore ores formed by weathering of a carbonatite. The ores are composed of pyrochlore, columbitized pyrochlore, monazite, apatite, magnetite, ferric and manganese hydroxide, titanic iron ore, zircon, hydromica, quartz, feldspar, and carbonates. A gravity-flotation enrichment flowsheet with application of cationic and anionic collectors has been developed. This flowsheet allows for obtaining a pyrochlore concentrate containing 44.3% Nb2O5 and 1.89% P2O5 with recovery of 55.83% Nb2O5 as well as an apatite concentrate containing 39.2% P2O5 and 1.05% TR2O3 with recovery of 62% P2O5 and 43.23% TR2O3 from ores containing 0.92% Nb2O5, 16.9% P2O5 and 0.6% TR2O3. Rare-earth concentrate containing 40% TR2O3 with recovery of approximately 10% TR2O3 was obtained at the same time. Major losses of valuable elements are related to slimes, which make up more than 50% of the ground ore. The niobium concentrate does not meet the phosphorus and radionuclide concentrations needed for the production of ferro-niobium. Acid leaching and sulfatization provided a high level of phosphorous and radionuclide removal. Conditions include hydrochloric acid pre-leaching at 75- 80°C with an 18% HCl solution for four hours and low-temperature sulfatization of acid-leached concentrate at 160-180°C for one hour followed by water leaching of the residue. The apatite concentrate could potentially be processed using nitric acid leaching. This technology is based on decomposition of apatite concentrate with 55-57% strength nitric acid with transfer of rare-earth metals into solution in the form of ammonium phosphate. This technology recovers a rare-earth concentrate containing 95% TR2O3 with extraction of 86%, and highly concentrated polynutrient fertilizer (ammophos) with phosphorus extraction of 95%. The completed research shows how complex multicomponent ores of residual soil may be processed for the extraction of niobium, phosphorus, and rare-earth products.

Jan 1, 2016

By A. Yousefpour, M. Hojjati, G. Chouinard

In recent years, high performance thermoplastic composites such as PEEK and PEKK have been developed for aerospace applications. These materials offer, among the other properties, high toughness and damage tolerances. These are semi-crystalline materials and their processing can lead to different crystallinity that in turn have some impact on the final properties. The effect of cooling rate on degree of crystallinity of PEEK is studied to identify the processing window for manufacturing. Samples were heated at the constant heating rate of 20°C/min up to 375°C (above melting point) and held for 10 minute. The enthalpy of the crystallization was measured at different constant cooling rates of 0.5, 1, 2, 5, 10, 20, 30, and 40°C/min. After cooling, the samples were heated at constant heating rate of 2°C/min using modulated DSC. At temperature between 90°C to 375°C, two endotherm peaks were observed. Results suggest that endotherm peaks are related to a melting and recrystallization phenomenon of one crystal morphology. However, the second endotherm peak could be associated with another crystal structure or morphology.

Jan 1, 2006

By J. P. Mogan, E. D. Dainty

Polynuclear aromatic hydrocarbon (PAH) levels were measured in underground mines in the vicinity of diesel vehicles equipped with several types of emission control hardware. In general, the emission control devices appeared to reduce PAH levels, but the companion mutagen study suggested that the reduction might not always be beneficial. All underground PAH concentrations were below the threshold at which a significant impact on health might be expected, but recent animal exposure studies have indicated that PAHs may not be the primary hazard from chronic diesel fume exposure.

Jan 1, 1994

By James A. Deeks

"Motor failures and equipment bearing failures are responsible for reduced productivity.With the introduction of computers and data acquisition systems, users are now able to monitor, report and trend deteriorating conditions and take corrective action before a critical shutdown occurs.This paper discusses the monitoring and trend analysis of' motors, and motor and equipment bearings. With today's digital electronics technology users are now able to monitor their equipment, detect deteriorating or abnormal conditions quickly, alarm the condition locally and or remotely, and decide if immediate corrective action is necessary or if it can be delayed until the end of a work Shift. All of this can be done long before any damage is done to the equipment.Monitoring Trend AnalysisIt is no longer necessary to compromise in selecting products, since state-of-the-art designs allow the adjustment in such small increments that the users are able to detect minute changes in a system's performance.Monitoring and trending of motors and equipment bearings is now available in economical packages which can be expanded as a system grows. Simply select the information you need, set the parameters, choose the scan time, and decide on the degree of reporting.Buffer storage of short-term monitoring of a number of analogue channels permit the user to view the recent history of motor data such as: motor average load, unbalance, motor current, ground fault, reserve thermal capacity, plus all of the settings of the protective device.A decision can be made to freeze the stored information after the motor stops or after the motor starts. Then the user is able to recall the conditions and diagnose the performance and the cause of the abnormal condition. Typical scan times range from ¼ second to 5 seconds ."

Jan 1, 1992

By N. Morrison, E. J. Rogans, A. J. Macintosh, N. Schoeman

"The design of carbon-in-pulp (CIP), and carbon-in-leach (CIL) adsorption circuits has essentially remained unchanged since the early days of the carbon process for gold recovery. For CIP circuit the pulp residence time is traditionally fixed at one hour per contactor with a carbon concentration of between 15 and 20 grams per litre, and the counter current carbon transfer rates are in the region of 15% pulp recycle. For CIL, the pulp residence time is usually three hours per contact or, with lower carbon concentrations ( 5 to 10 grams per litre).The drawbacks of using the counter current CIP/CIL adsorption circuits are discussed using modeling developed for CIP/CIL plant design. Counter current CIP/CIL, circuits are then compared with the carousel method of adsorption circuit design.The use of equipment suitable for the carousel approach is discussed which is, the AAC cylindrical and pumping (MPS) screens, the AAC pump-cell plant and launder designs.Finally, two plants at the Vaal Reefs Gold Mining and Exploration Company that use carousel adsorption circuits, namely the Vaal Reefs No. 1 Gold Plant, a CIL plant with stepped contactors, and the Vaal Reefs No. 2 Gold Plant, a CIP using a very short residence time (AAC pump-cell) are discussed."

Jan 1, 1998

By P. R. A. Andrews

"Garnet occurs in schists and gneisses in all provinces of Canada, all mainly in Quebec and Ontario. There is currently a renewed interest in exploration for economic sources of garnet for abrasive applications because of the inherent dangers from exposure to ground silica from sandblasting operations.High-quality garnet is used for lapping and grinding of glass and ceramics; for coated and bonded products such as sandpaper and cloth; and abrasive wheels for grinding and finishing various metals, woods, rubber and plastics. Low-quality garnet is used for cleaning and conditioning aluminum and other soft mewls, particularly by aircraft manufactures. Garnet may be added to grouting cements for oil-well drilling applications, and it has also been used for low- to medium-level radiation shielding. Garnet has been studied extensively by CANMET and its predecessor, Mines Branch, between 1917 and 1990. Twenty-nine studies relating 10 various aspects of beneficiation are presented and a review of the more important studies is presented. The information includes mineralogy, beneficiation methods, product sizes and analyses."

Jan 1, 1995

By X. Cao, X. -G. Chen, K. Liu

Due to the detrimental effect of platelet iron-rich intermetallics on mechanical properties (particularly ductility) in cast alloys, it has been essential to transform these phases into Chinese script morphology. In the present work, the effects of Mn and/or Si addition and cooling rate on the phase transformation of the iron-rich intermetallics in 206 cast alloys with different Fe contents ranging from 0.15 % to 0.5 % were systematically investigated. The results obtained showed that platelet ß-Fe and Al3(FeMn), Chinese script a-Fe, Alm(FeMn) and Al6(FeMn) can be observed in the 206 cast alloys, depending on the Fe, Mn and Si contents as well as the cooling rate. It was found that the addition of either Mn or Si favors the formation of Chinese script iron-rich intermetallics but inhibits the precipitation of the platelet phases. In addition, the combined addition of both Mn and Si has a synergistic effect on the phase transformation. Furthermore, there exists a critical cooling rate to effectively suppress the formation of platelet iron-rich intermetallics for a given alloy. The threshold cooling rate decreases with increasing Fe, Mn and Si contents. Casting process maps are established to correlate the intermetallics precipitated with alloy chemistry and cooling rate for 206 cast alloys containing various Fe levels.

Jan 1, 2014