Search Documents

By R. Spring

"Soft-sensors are a computer software alternative to inadequate hardware instrumentation. Filters are averaging methods that reduce the noise in any sensor's signal. This paper introduces these topics and places them in a mineral processing context using then-product formula.Soft SensorsAs their name implies, ""soft-sensors"" are computer programs that estimate values for process variables (Tham, 1991). This approach is useful when the appropriate hardware sensor does not exist, is deficient, supplies only infrequent values, etc. For example, in mineral concentrators the traditional magnetic flowmeter/ nuclear density gauge instrumentation for measuring slurry flows costs $5,000 or more per flow and requires frequent maintenance. However, metal assays are commonly available from online X-ray fluorescence analyzers and application of the n-product formula (Taggart, 1945) to these assays conveniently provides software estimates of the flowrates (albeit only when the circuit is in steady-state).Soft-sensors are used by inferential controllers that base their control actions on the process values ""inferred"" by the soft-sensor. Such was the case at Brenda Mines where the rod mill feed tonnage controller used an inferred value of the cyclone overflow particle size (Bradburn, 1976). It was also the case at Brunswick Mining where reagent controllers adjusted reagent addition rates throughout the plant according to the various ore flowrates inferred by an expert system (Spring, 1991). A unique feature of the expert system soft-sensor was its dynamic flow models which compensated for residence times, material transport lags, etc. Thus the soft-sensor values were valid under both steady-state and nonsteady- state conditions."

Jan 1, 1992

By H. E. Wilde

"Zinc has been used for many years as a galvanic coating for the protection of steel. Electrochemical measurements show that zinc actually overprotects steel. The corrosion rate of DQSK (drawing quality semi-killed) steel in air saturated salt water was determined as a Junction of applied cathodic potential. The resulting data indicate that at a critical cathodic over potential of - O. 725 Vsce an acceptably low corrosion rate of less than 1 mpy occurs. Using the developed criterion, alloys of Zn/X and AL/X were produced and evaluated in galvanic contact with steel in a standard laboratory test. The results indicate that Zn /Mn, Zn /Co, AI/Mg/Si and AI/Mg/Ge alloys offer excellent galvanic protection along with (a) no hydrogen evolution, and (b) improved dissolution life over Zn coatings.IntroductionZinc coated (galvanized) steel has been successfully used in applications where bare (or painted non-galvanized) steel would suffer corrosive attack. In general, galvanic coupling to zinc, as either an anode or a coating, is an effective means for combatting steel corrosion. Because of this, the use of galvanized steel has increased markedly, stimulated primarily by automobile manufacurers seeking to extend the corrosion warranties on automobiles(1).Although effective, zinc coatings are not without a number of drawbacks which warrant efforts to improve them. For example, because of the widely differing electrode potentials between zinc and steel ( - 1.05 Vsce and - 0.60 Vscc, respectively, in air saturated NaCl solutions), the zinc corrodes at a rapid rate to protect the steel. This is reflected in the limited lifetimes of galvanized unpainted siding. The basic electrochemistry controlling the situation is shown in Figure 1, for a system controlled by oxygen reduction. The zinc corrodes sacrificially to protect the steel, while cathodically polarizing the steel to a potential near that of zinc's open circuit anode potential."

Jan 1, 1990

By Nirmal Weerasekara, Jochen Franke, Malcolm Powell, John Favier

Mill liners serve the dual purpose of protecting the shell from wear and transferring the rotary motion of the mill to an effective grinding action. As the liners wear, the efficiency of energy transfer changes, so there is balance between liner profile for wear and for milling efficiency. A tool that can simultaneously predict the evolution of the liner profile and the associated change in milling efficiency should prove most useful in optimal liner design. This paper presents such an approach, based on measured 3D liner profile data informing 3D DEM simulations of charge motion and liner wear modelling.

Jan 1, 2012

By Daniel J. Corkery

Mines in Canada and the United States are subject to regulations limiting ammonia, nitrate and nitrite levels in mine effluents released into the environment. The primary source of these nitrogen compounds is typically explosive used in blasting operations, as ammonium nitrate (AN) remains a significant component of most explosives used in the mining industry. The amount of AN entering a local water drainage system is related to site conditions, explosives used, explosive handling and blast efficiency. Mining operators acknowledge AN loss to mine water from blasting operations. However, the mechanisms by which ammonia, nitrite and nitrate are entering the water drainage system, or the relative contribution of specific mechanisms, may not necessarily be assessed or monitored adequately. Characterization of these mechanisms, through systematic investigations, allows a mining operation to focus its efforts on reducing AN loss. This paper outlines a strategy for investigating the mechanisms through which AN enters the mine water drainage system and methods to mitigate this loss. This strategy includes collection and analysis of data to identify and quantify the AN loss mechanisms, design and implementation of tests to mitigate this loss, and assessment of the results. Such investigations are not intended to be a separate one-time project, but part of a long-term process of continual feedback and optimization that is related to the collection and reporting of AN levels for regulatory purposes. The implementation of the strategy must be tailored to each mine?s requirements and existing conditions.

Oct 1, 2010

By David J. Morrison

Scarcity of truck tyres, increasing cost and decreasing availability of labour, increases in fuel costs and project budget blowouts have changed the paradigm behind mining equipment selections. The cycle of commodity changes have occurred in parallel with the increasing maturity of continuous mining machinery, mobile in-pit crushing systems and very large scale conveyor belt systems. This paper will consider the merits of operating continuous materials handling systems, mobile in pit crushing systems, relocatable crushing systems, relocatable conveyor systems and automated waste handling systems in place of the more conventional approach of truck haulage.

May 1, 2007

By E. L. Day

"In the early 1930s during the course of test work with a simple gold ore, it was evident that the time required to dissolve the gold by cyanidation was very much longer than should have been needed theoretically for the maximum size gold particles in the ore, A similar conclusion appeared to be valid for other gold ores. In a cyanidation system there are many factors which can influence the dissolution rate of gold, and a decision was made to investigate the more obvious variables, because a literature survey at the time showed that with the exception of the work of Yamazarki on the dissolution of silver in cyanide solution, virtually no attention had been given to this subject, Our work was not reported because the intention was to do this on completion of the Study, but owing to the demands on the Section's personnel for other work the investigation was never completed. Although other investigators have since studied the problem, the methods which we adopted and some of the conclusions may be of interest to metallurgists concerned with gold ore treatment.Form of GoldExperiments with gold ores were not possible because of the number of uncontrollable variables present in a gold ore-cyanidation system, therefore pure metal and reagents were used. Initially some experiments were carried out with gold leaf, but it was soon apparent that metal in this form was unsuitable because the uneven thickness of the leaf caused it to break up into pieces and. there was difficulty in determining precisely when complete dissolution had taken place, Numerous factors both expected and unexpected were found to influence considerably the results and much experimental work was necessary to establish the procedures which were finally adopted, Experiments were carried out with gold in the form of foil, wire, rings and sols. Finally, gold foil in the form of cylinders was adopted for most of the experiments although some work with gold in the sol form was included in the programme. Also some experin1ents were carried out with a gold ore to see if effects which were obtained with sodium chloride on gold sols were applicable to gold ores."

Jan 1, 1967

By Gonzalo Bernstein, David G. Meadows, German Naranjo, Edgardo Tapia

"During the last decade Antofagasta Minerals’ Los Pelambres Mine has dramatically increased its ore throughput following the fast initial phase ramp up through a series of planned incremental expansions. The original 85,000 mtpd, two SAG line plant was commissioned in 1999 and rapidly exceeded nameplate tonnage in only a few months. Following this, the inclusion of a pebble crushing circuit resulted in throughputs in excess of 114,000 mtpd and a recent, final third line SAG and ball mill addition have taken the plant to over 175,000 mtpd even with increasing ore hardness and changing ore feed characteristics. The progressive changes are described in this paper together with how the technical challenges have been met.INTRODUCTIONMinera Los Pelambres is a world class copper-molybdenum operation located in the Salamanca area in Chile, in region four, approximately 500 km north east of Santiago, the capital of Chile. In the late 1990s Antofagasta Minerals developed the Minera Los Pelambres project in Chile at an investment cost of approximately $1.3 billion USDs. The project construction was successfully led and completed by Bechtel Corporation in 1999 and within a matter of months the plant was already exceeding the nameplate capacity of 85,000 mtpd. In 2001 a pebble crushing circuit was added to raise the capacity to 114,000 mtpd. In the early part of 2003-2004, it was recognized that the hardness profile was changing with depth and that in order to maintain the plant capacity additional power would be needed in the SAG mills together with upgrading of the primary crusher. In conjunction with these changes a fifth ball mill and a second primary crusher station would also need to be installed. A further detailed engineering study and evaluation was initiated by Minera Los Pelambres. This was lead by Bechtel Corporation with major design contributions from FLSmidth and Siemens in order to establish the re-powering requirements for the SAG mills. These re-powering changes together with the inclusion of a pebble crushing circuit took the plant to up to 125,000 mtpd even with harder more competent ores. Finally in the last two years an additional grinding line has been added to take the capacity to consistently over 175,000 mtpd. The third line was installed in a record time of 256 days. A schematic of the current comminution circuit, discussed in this paper, is shown in Figure 2."

Jan 1, 2012

By A. de Ville d’Avray, G. Guezennec, P. Wavrer, E. Braak

The aim of the European CEReS project was to develop an innovative copper recycling route based on the coprocessing of coal production waste by bioleaching and printed circuit boards (PCBs) from Wastes of Electrical and Electronic Equipment (WEEE). Coal waste is processed by bioleaching in stirred tank reactors, and the resulting bio-lixiviant solution is used to extract copper from PCBs pre-treated by catalytic cracking. Copper is then extracted using solvent extraction, stripping and electrowinning. The whole process flowsheet combines thermal, biotechnological, physical and hydrometallurgical operations. Once the process concept has been validated at laboratory scale, a simulator of the whole process has been built in the USIM PAC software platform. The tool enables to improve the analysis of the results of the lab-scale experiments and to design industrial-scale scenarios by simulation. The results of such simulations allow to estimate the economical interest and to perform environmental impact assessment. After presentation of the CEReS project objectives and main results, the paper describes the methodology used to build the simulator and define the scenarios corresponding to feasible process routes. The main results of the simulations are then presented with technical, economic and environmental point of views. INTRODUCTION Because of rapid technological innovations in the electronics industry, electronic waste represents the fastest growing waste stream in the world, especially in developing countries (Işildar et al., 2018). Meanwhile, the global copper demand is expected to go on rising in the future. As significant amounts of copper are present in end-of-life printed circuit boards (PCBs), it becomes a necessity to develop efficient copper recycling routes. Metal refining from e-waste is traditionally performed by pyrometallurgical processes. However, the hydrometallurgical processing of PCBs, which has been shown to be technically feasible at laboratory scale with a wide range of leaching reagents, could be a less energy intensive and more flexible alternative (Tuncuk et al., 2012). However, a large amount of leaching reagent is required to leach the metals from PCBs.

Jan 1, 2019

By J. F. Perreault, J. Paraszczak

"The profitability of an underground mine depends to a great extent on the production cost.Random equipment failures and their consequences have significant influence on the total operating cost of a mining system. Having this in mind, a reliability study has been initiated for loadhaul- dump machines in an underground mine. The main purpose of this study is to identify the critical machine subsystems, determine their failure pattern and help work out an effective maintenance strategy. In the first part of this study, the failure data of diesel powered LHDs, gathered during an I8-month period have been analyzed. For the purpose of the analysis, the machines have been treated as systems comprising seven subsystems connected in series. The most critical subsystems, i.e. electrical and hydraulic, were further investigated, and analyzed by graphical and analytical methods. Different failure distribution models were applied and discussed. Basic Defmitions and ConceptsIn order to avoid confusion, several terms used in this paper are defined below, as compiled by O'Connor (1991). The acronymsBS and MIL-STD stand respectively for: British Standard and US Military Standard.Failure: the termination of the ability of an item to perform a required function (after BS 4778).Time Between Failures (TBF): the length of time between two consecutive failures.Observed Mean Time Between Failures (MTBF): For a stated period in the life of an item, the mean value of the length of time between consecutive failures computed as a ratio of the cumulative observed time to the number of failures under stated conditions (after BS 4778).Maintenance, Corrective: The actions performed, as a result of failure, to restore an item to a specified condition (after MIL-STD-721 B).Maintenance, Preventive: The actions performed in attempt to retain an item in a specified condition by providing systematic inspection, detection and prevention of incipient failure (after MIL-STD-721B)."

Jan 1, 1994

By A. J. Williams

"Whenever a decision is made to bring a mineral deposit into production, the Owner in actual fact has decided to convert substantial sums of capital into productive capacity with the intenti6n of making a profit from such conversion.Escalating costs of construction, frustrating and costly delays in comp1etion, the increasing tempo of technological change and the increasing size and complexity of mineral processing projects have convinced Owners that the best way of implementing their capital must be sought and utilized. This requirement has stimulated a search for ways and means of applying modern management techniques to the design and construction of mineral processing plants.This search by consulting firms has resulted in the evolution of the concept of project management and the development of planning and con trolling techniques with the result that Owners can seek and obtain better assurance that their project objectives will be fulfilled.This paper will attempt to outline how a mineral processing plant can be brought into production through the implementation of project management techniques.Definition And Objectives Of Project ManagementThe design and construction of mineral processing plants is subject to the restraints of three inter-related parameters -Quality, Cost and Time each of which influences and is influenced by the other two.Project management is a technique where the Owner delegates complete responsibility to a single organization for all phases of a project (design, procurement, construction and commissioning) for the above parameters but retains freedom for major decision making. Normally, the consultant under-takes full responsibility for all phases, but partial project management services can be provided when the Owner so desires.The objective of project management is first to devise and define and then to implement a program in which the relationship between the three parameters of Quality, Cost and Time is optimized, i.e., the desired functional and other requirements are attained (but not exceeded) at the lowest practicable overall cost in the shortest practicable time. The measure of success of a project lies in the degree to which this objective is achieved."

Jan 1, 1974

Since 2008 rapid advances have been made in technologies for the sensing and sorting of ores, particularly copper, and copper-related ores. Advances include significant increases in the sensitivity and throughput, specifically in the area of bulk sorting. Such advances were not possible without contemporaneous advances in the understanding of copper orebodies, in particular the understanding and quantification of the heterogeneity required within an orebody to support an effective sort, regardless of the technology deployed to do this. This paper covers fundamental knowledge in the characterization of orebodies and their ores for sorting; relationships between measures of heterogeneity and sorting response; the design of bulk sorting systems that can exploit this heterogeneity to add value to copper operations; and, a quantification of the value that can be generated from bulk sorting at a case study mine. INTRODUCTION Society currently puts increasing pressure on industries to move towards cleaner and more efficient means of production, and the mining industry is no exception. Mining additionally faces other factors increasing the pressure to be more efficient: high-grade and easily accessible reserves have become largely depleted, therefore the mined grade at operations across most commodities, including and in particular copper, is decreasing. Additionally, the grade of new discoveries in the sector continues to decrease (Schodde, 2011). Factor in the high capital cost of processing facilities and the low levels of efficiency of current grinding circuits, and the situation for such mines becomes dire. Sorting, by maximizing the amount of ore extracted while simultaneously reducing the waste content in ore delivered to downstream processes (whether simply transport and crushing, or more sophisticated circuits such as grinding and flotation or leaching) has long been of interest to mining operations and projects struggling with low margins (Bamber, 2012). However, until recently sorting technologies that are both cost effective and effective at such high throughputs have not been commercially available.

Jan 1, 2019

By Stephen Hardcastle

Personnel Heat Exposure Issues In Canada?s Deep Mechanized Mines ?Project developed in 2004 ?Base/precious metal industry identified heat stress/management as a major challenge affecting productivity and operating costs ?Project started in 2005 ?Current research nearing completion ?Guidelines, further data analysis and ?Communicating the Science? will continue into 2011 Managing Heat Exposure Control?. The cost implications ?Controlling the environment ?Ventilation already a major expenses/energy user ?Large Canadian mines are currently delivering massive volumes of air 15-20 tons of air/ton ore ?Large investments in ventilation upgrades, mechanical cooling

May 1, 2010

By N. Bartie

Realising the circular economy (CE) is faced with some significant challenges. Process metallurgy and its infrastructure play key roles at the heart of making the CE work. Therefore, the enabling role of process metallurgy within the CE will be central to the discussion in this paper, touching among others on product and system design as well as the key metallurgical and other process fundamentals that need to be investigated and understood to make the CE a reality. The central role of materials and its processing will be discussed in an integrated circular cities perspective. A key focus will be a discussion on designing a resilient “Smart Materials Grid” using and innovating metallurgical process engineering tools, which will manage the flows through Sustainable Circular Cities. The discussion will be using copper as leitmotiv of the discussion i.e. from copper ore, to metal, to complex products, recycling, product design and simulation and its impact. INTRODUCTION The transformation of our economies from linear to circular models in which waste materials become resources is the focus of the Circular Economy (CE) paradigm. Its important intentions: to take control of the damage we have been doing to the planet to ensure its livability and the welfare of future generations. This can only be achieved through careful utilisation of human, natural and economic resources. The concept is derived from several others (Beaulieu et al., 2015), of which Cradle-to-Cradle, Extended Producer Responsibility (EPR), Industrial Ecology, and Life Cycle Thinking are just a few. Other relevant concepts include resource efficiency (RE), design-for-recycling (DfR), and various others discussed by Blomsma and Brennan (2017) and Homrich et al. (2018), as well as various R-hierarchies e.g. Reduce, Reuse, Recycle (3R). However, does society comprehend these concepts, the actors and actions that influence them and how they interact? Do we know the limits of CE? Does society understand the key role of Copper and other metals to rendering the CE operable? True life cycle and systems thinking, focussed on simulation-based, process and metallurgical design are required to answer these questions. Lieder and Rashid (2016) identify nine widely-varying fields that study the concept ranging from sustainability sciences and engineering to economics, business, law, and social sciences. Overlap between questions addressed highlights the need for interdisciplinary collaboration (Nanz et al., 2017) in the assessment of the current status, and further steps needed to transform to CE. This doesn’t apply just in academia, but also in industry where concrete implementation of CE needs to occur at multiple levels, thus necessitating cooperation between government, civil society and other stakeholders (Beaulieu et al., 2015).

Jan 1, 2019

By D. Saramak, Z. Naziemiec

"Chalcedonite is an unique rock due to the relatively small area of its occurrence. It also possesses multi-raw-material features therefore it should be given a special protection aiming at its complete and optimal utilization. It is the natural sedimentary rock and the only mine in Poland, located in Inowlodz, where the opencast mining from “Teofilow” deposit is carried out.Chalcedonite mainly consists of cryptocrystalline and microcrystalline chalcedony together with small amounts of autogenous and detrital quartz. The chalcedony itself is a fairy common mineral and many forms of its occurrence is known, some of them are semi-precious minerals. Among the most popular ones following can be found: agate, bloodstone, onyx, carnelian, chrysoprase. Many countries own chalcedony deposits: Australia, Brazil, India, Canada, Namibia Russia, South Africa. However chalcedony in its pure form does not occur in the mentioned chalcedonite rock. The pores, which take usually from 5% to 25% of volume and have sizes smaller than 0.5 mm, are the characteristic feature of all chalcedonite forms. The paper presents some crucial problems of its processing together with most significant directions of its applications. New method of chalcedonite enrichment based on densimetric separation (patented in Poland) is presented. Results of investigation show that the obtained products can increase quality of concrete and filter grits."

Jan 1, 2016

By B. J. Cunliffe

"Filter cloth in the mining industry is an ambiguous title asthis suggests filter cloth use from underground ventilation to the refining processes. The time allowed for this paper would be better served in con-centrating on vacuum filters common to all mine mills and to offer some simple guide lines to the mill metallurgists in the choice of filter cloth for this type of filter.The requirement of the filter cloth is to separate solids from liquids under a vacuum head by forming a permeable layer of solids or cake, through which liquids can flow until the panel or disc sector leave the slurry tank and to continue to pass residual moisture from the cake formed during the cake drying cycle, and to discharge the cake on air-blow so that the cycle can be repeated.Whilst the mill metallurgist should not be expected to under¬stand all aspects of filter cloth manufacturer, it is however, advantageous for him to understand a little of the textile language associated with filter cloth for his own protection against ""trial-and-error"" methods, which are both time consuming and costly.If improvements are to be made over existing filter cloth in use an examination of the limiting factors of the cloth used should be made and the major causes for removal determined, e.g. cloth blinding, high moisture in cake, poor cake discharge on air blow, mechanical damage to cloth.As each of the limiting factors mentioned has a bearing on the choice of fibre used, the yarn type and weave of a suitable cloth, an under-standing of these points will assist the mill metallurgist in avoiding repetitive trials offering little degree of success."

Jan 1, 1971

By L. Tang

A seismic monitoring system was installed in 2005 at Dongguashan Copper Mine, the deepest metal mine in China. Based on the seismic events monitored in situ, the possibility of rockburst prediction and prevention is investigated in this paper. The characteristics of space-timeintensity of mining-induced seismicity and the seismic response to mining are studied in detail using the seismic data in Dongguashan Mine. A conceptual model and a criterion of assessment of hazard seismic nucleation are proposed for Dongguashan Mine. In this model, the mine seismic stiffness method is adopted for rockburst prediction within the framework of the unstable failure theory. To analyze rock failure cases in Donggauashan Mine, the rate of the ratio of stiffness of rock in nucleation area to its surrounding area is proposed as a criterion for rockburst prediction.

May 1, 2009

By R. M. de Carvalho

Empirical and phenomenological models of SAG and AG mills have dominated the scene for the last few decades, being used nearly every time a mill is scale-up or an attempt is made to improve its performance. However, in spite of their success, these models fail to describe the details of both the grinding environment and the breakage mechanisms. The result is a generally good track record, with a few – but very important – instances when these models fall short in their predictions, which can be very costly. Further, nearly all of these models require detailed calibration to industrial and pilot plant data, being costly in their application, although still with limited predictive capabilities. Recognizing these challenges, a new model framework has been proposed which overcomes the limitations of currently used models by coupling the microscale population balance model, the discrete element model and functions that describe internal classification at the mill grate. This model framework has already been applied to describe breakage in ball mills, with showing very promising results. However, in the case of SAG and AG mills a much greater level of complexity is involved in the model, given the interaction between the mechanical environment that is formed totally or, in part, by the ore itself, and the breakage response in the mill. The paper describes the model framework, demonstrating how it can address appropriately effects such as mill speed, mill filling and size distribution, on the response from the mill. Some of the advantages of the model are related to its intrinsic multi-component and dynamic nature, which allows simulating appropriately mixtures of ores of different competences in a transient manner.

Jan 1, 2012

By M. Sider, D. L. Piron

"The cost of energy is a growing factor in the cost of zinc production. Electrowinning from sulphate solutions with periodical reverse current or from acidic chloride or alkaline solutions could be the way to lower costs. A comparison of the energy consumption for electrolysis shows that the alkaline solution may be considered the most promising alternative. IntroductionZinc electrowinning from sulphate solutions is a very energy intensive process (typical specific energy usage : around 3.1 kWh / kg zinc). This energy consumption represents 35% of the total cost of electrolysis and is the most important cost component.In order to lower costs, the energy efficiency of the sulphate process should be improved or alternative processes should be developed. In this laboratory, that objective has resulted in research on electro winning in sulphate solutions with the use of periodical reverse current (PRC) and in acidic chloride and alkaline solutions.Some of the results obtained in this laboratory and already published and new experimental results reported in this paper make it possible to present a more critical comparison of the energy consumption of the three processes mentioned.ExperimentalThe experiments at constant current were carried out as described previously. Specific conditions are indicated in Table I. Current efficiencies were obtained by weighing deposits.ResultsThe best energy consumptions for electrolysis obtained in this laboratory for the three media are presented in Table I. More detailed results can be found in the papers already mentioned."

Jan 1, 1988

By E. R. Rivenbark

"The coal handling plant represents an investment of about $100 million in coal handling and storage equipment. The coal receiving is done by a continuous ship unloader that can handle ships in the 60 000 T range at Q rate of 1750 /ph. A unique feature in the system is a stacker/reclaimer unit which will work inside a dome storage structure. The coal for the unit will include any low sulphur coal that can be delivered by sea at an economical price blended with New Brunswick high sulphur coal.ThE flue gas scrubber is a wet limestone system capable of 95% SO2 removal. The scrubber will utilize about 150 000 tonnes of limestone per year and will produce commercial grade gypsum by the forced oxidization method.IntroductionWith the need for new generating capacity being required, New Brunswick Power reviewed, in 1985, its options for the next unit. The study indicated that the most attractive option for New Brunswick Power would be a coal-fired unit capable of receiving imported coal at a sea port. The site selection process resulted in three site options being considered.The existing Coleson Cove and Dalhousie sites, and the Belledune site were considered. To meet load distribution needs, it was then decided that the unit had to be located in the northern section of the province, thus eliminating the Coleson Cove site. The Belledune site was selected because it had the capacity to have additional units added where as the Dalhousie site would have only been able to accommodate one unit"

Jan 1, 1994

By D. Nie, M. Ren, T. Mo

This paper studied the phenomenon of room temperature creep deformation at crack tip and its effect on fatigue crack growth rate of a X-70 pipeline steel using compact-tension (CT) specimen on a MTS 810 testing machine. Time-dependent deformation at the crack tip under constant load was observed in this steel at room temperature and the amount of deformation produced was seen to depend on loading rate and the magnitude of stress intensity factor. It is found that there exists a critical stress intensity factor below which the deformation decreases with time when the applied load remains constant. It is also found that the occurrence of room temperature creep obviously affects the subsequent fatigue crack growth rate. The observed behavior was explained based on dislocation theory.

Jan 1, 2005