Search Documents

By G. D. Just

"Extensive mechanization of underground mining operations, improvements in blasting technology and the development of simulation models for systems evaluation has now made it feasible to optimize rock fragmentation and materials handling operations. Methods of achieving these objectives are described in this paper, with particular emphasis on the need to obtain precise field data measurements. Techniques are illustrated with reference to the sub-level open stoping system of mine production. IntroductionThe primary objective to be achieved in any mining system is to deliver a specified grade of ore to the mineral processing plant at a planned delivery rate and at the minimum total mining cost. Design and management of such a system is complicated by the large number of unit operations and the often unknown inter- relationships between the different unit processes. This particularly applies in underground mines, where planning restrictions and unit costs are much greater than in comparable tonnage sur face mining operations. These difficulties can often be resolved by the application of judgment based on extensive experience, but the costly trial -and-error methods required for new technology discourage innovation.Most modern medium- and large-scale mines are now extensively mechanized. Consequently, the performance of each unit operation by individual items of equipment should be predictable for a given set of conditions. An essential prerequisite is that quantitative performance data are available from field measurements. Such information can then be used to optimize the design and management of the complete mining system to achieve the minimum tot al mining cost. One of the most significant factors influencing all unit costs is the degree of rock fragmentation. The importance of this variable is indicated by the fact that opt imization of rock fragmentation implies minimization of tot al mining system costs."

Jan 1, 1980

By F. Weinberg

"The recent development of the continuous casting process for steel has required basic understanding in a number of areas in the metallurgcal sciences. In some areas, information is still lacking. The success of the application of basic knowledge and research to the process is evidenced by the fact that a large percentage of the steel now produced in the world is produced by continuous casting.A number of areas in which metallurgical science has contributed and is currently contributing to better design and control of the continuous casting process and leading to a better quality product will be considered. These include:(a) heat transfer studies of the entire casting process;(b) fluid flow in the tundish, strand and liquid metal stream;(c) solidification structure and segregation;(d) strength and ductility of steel at high temperatures related to bulging and cracking; and(e) problems related to horizontal casting developments.IntroductionThe continuous casting of steel is a relatively new technology in steelmaking. It is now used extensively throughout the industry. In Japan, for example, continuous casting accounts for approximately 40010 of steel production, and this value is expected to increase to over 50% in the near future . New steel plants are now designed to use continuous casting exclusively. This means the process must work well and be completely reliable, because all the steel produced must go through the caster.The development of the continuous casting process in a short period of time has required concerted research and development in many areas . I shall cite a number of examples of these developments and refer to work done in Canada when applicable. No attempt will be made to review all of the research in continuous casting, nor refer to all of the workers in the field.The developments in continuous casting are based in many cases on metallurgical science, as described below. The use of metallurgical science in these developments is qualitative, in that concepts and idea s are used, as opposed to quantitative values calculated from fundamental equations. In general, most metallurgical problems are too complicated to enable fundamental equations to be used without the introduction of uncertain approximations and boundary conditions in the calculations.Starting at the beginning of the steelmaking process, very extensive research and development has been carried out to produce liquid steel of the required composition and temperature. The replacement of open hearth furnaces with BOF furnaces reduced refining time from many hours to roughly 30 minutes for 250 tons of steel. Two BOF furnaces effectively enable a continuous flow of steel to be available in a plant, essential for the introduction of the continuous casting process. This area of research will not be considered here."

Jan 1, 1981

By J. C. Kurnia

Presence of fine dust in air causes serious health hazard for mine operators resulting in such serious problems as coal workers? pneumoconiosis and silicosis. Major sources of dust appear of course along the mining face where the minerals are extracted. Proper control and management are required to ensure safe working environment in the mine. Presented here is the use of a computational fluid dynamic (CFD) approach to investigate the flow and dust behaviour in mining tunnels. The objective of this study is to propose and examine various strategies to mitigate dust dispersion from the mining face and reduce dust concentration to a safe level for the operator. In a companion study, the authors investigated various methods for mitigating dust dispersion from the mining face to ensure safe dust concentration levels in the mine tunnel. Among the examined methods, implementation of brattice to direct the flow from the main airway to the mining face is the most effective method to disperse dust particles away from the mining face. The installation of brattice, however, will limit the movement of mine operators and vehicles in the tunnel. Hence, application of a hybrid brattice which is a combination of a physical brattice along with suitable directed and located air curtains is proposed and examined. Based on the CFD simulation results, over a range of parameters of interest, it was found that the physical brattice blocks the ventilation air and directs it to the mine face while an air curtain located along the brattice outlet offers flexibility in keeping the dust away from the operator allowing more freedom for the operator and the equipment. Results of the modelling over a range of parameters of interest are presented and discussed with the goal of managing dust concentrations within safe limits for the operator.

Aug 1, 2013

"Technological innovation is an extremely complex activity. The author presents his interpretation of innovation and the innovative process. He reviews the strategy used by participants in coal mining innovation in the past and discusses changes required to meet the challenges of the future.Introduction if an industry is to be successful and viable in today's world, the companies active within the industry must remain close to the frontiers of knowledge. The coal mining industry is no exception. Technological problems facing the coal mining industry are basically economic and social. Economic problems are those concerned with the long-term growth and profitability and social problems, with the health and safety of the mine worker and the impact of the mining operation on the environment.Technological innovation can be a key factor in meeting these problems successfully. The general belief is that the information base for technological innovation exists within mining companies and governmental agencies but current industrial and governmental strategies and structures impede the transformation of this knowledge into the mining products and processes required for growth.The purpose of this paper is to determine where Canada is in terms of coal mining on the innovative ladder. The paper as presented: defines innovation and innovative process; gives an historical ""broad brush"" review o f innovation in the industry; and suggests the challenges to be faced in the future."

Jan 1, 1985

"The United Nations, through the secretariat of the United Nations Economic Commission for Europe (UNECE) and its Ad Hoc Group of Experts on Harmonization of Fossil Energy and Mineral Resources Terminology, developed the Framework Classification.The UN Classification applies to fossil energy and mineral reserves and resources located on or below the Earth's surface. It aims to simplify reporting of energy and mineral reserves and resources in a globalized world and is intended to improve global communications regarding remaining quantities of non-renewable fossil energy and mineral resources. The UN Classification is not recognized as a Foreign Code under NI 43-101.SECTION I1.,The United Nations Framework Classification (UNFC-2009) applies to fossil energy and mineral reserves and resources located on or below the Earth' s surface. It serves the needs for classification at a global level (for energy and mineral supply studies), for governments (resources management and policy formulation), for industry (business process management) and for financial reporting.SECTION II2.,The UNFC is a generic system in which quantities are classified on the basis of the three fundamental criteria of economic and social viability (E), field project status and feasibility (F), and geological knowledge (G), using a numerical coding system. Combinations of these criteria create a three-dimensional system. Categories (e.g. El, E2, E3) and, in some cases, sub-categories (e.g. E1.1) are defined for each of the three criteria as set out and defined in Annexes I and II.3 The first set of categories (the E axis) designates the degree of favourability of social and economic conditions in establishing the commercial viability of the project, including consideration of market prices and relevant legal, regulatory, environmental and contractual conditions. The second set (the F axis) designates the maturity of studies and commitments necessary to implement mining plans or development projects. These extend from early exploration efforts before a deposit or accumulation has been confirmed to exist through to a project that is extracting and selling a commodity, and reflect standard value chain management principles. The third set of categories (the G axis) designates the level of confidence in the geological knowledge and potential recoverability of the quantities.4. The categories and sub-categories are the building blocks of the system, and are combined in the form of ""classes"". The UNFC can be visualised in three dimensions, as shown in Figure 1, or represented in a practical two-dimensional abbreviated version as shown in Figure 2."

Jan 1, 2003

"The Schist Lake mine, owned and operated by the Hudson Bay Mining and Smelting Co., Limited, is situated on the northwest arm of Schist Lake, 4 miles southeast of Flin Flon, Manitoba.The deposit was discovered early in 1947, during a diamond drilling program exploring small copper showings along the west shore of the lake. The orebodies came to surface between the mainland and the north end of Stitt Island.Production began in August, 1954, at an initial rate of 300 tons per day. Underground workings have been carried to the 1,700-foot level, where exploration work is now being done.General GeologyRocks of the area are Precambrian lava flows, with associated pyroclastic breccias and tuffs, and related minor intrusions. Their general strike is northwest and their dip is nearly vertical. Shearing is common and is related to the activity which caused intense folding and much faulting in the area. The larger faults and the fold axes trend a few degrees west of north. The lavas are mainly andesitic but a layer of sericite-carbonate schist, which is probably derived from a fine-grained, grey quartz porphyry, occupies most of Stitt Island and extends into the mine area. It is within this layer of schist that the ore deposit occurs (Figure 1).The OrebodiesThe ore occurs as tabular to lens-shaped bodies which strike northwest, dip nearly vertically, and plunge at 60 degrees to the southeast. The ore zone is 800 feet long and has been traced for a distance of 2,000 feet along the plunge (Figure 2). The maximum length of continuous ore within this zone is 200 feet. Widths of individual ore lenses vary from a maximum of 35 feet to a minimum of 2 feet.The ore consists of three distinct types: massive sphalerite-pyrite, massive chalcopyrite-sphalerite, and disseminated chalcopyrite-pyrite. The No. 1, or eastern, orebody is predominantly massive sphalerite-pyrite. The western part of the No. 2 orebody is massive chalcopyrite-sphalerite. The disseminated ore forms the eastern part and the lower end of the No. 2 orebody. All three types of ore, with patchy distribution, are found in the smaller lenses below the 1, 100-foot level.Metallic minerals, in order of deposition, are pyrite, arsenopyrite, chalcopyrite and sphalerite, galena, enargite, and gold. Both massive types of ore exhibit banding in many places, probably as a result of the selective replacement of schist. The disseminated ore was formed as a filling of the interstices in a brittle chert rock which appears to have been crushed by the same forces which produced the schist."

Jan 1, 1949

By Patrick J. Williams

Outline -An Australian View On: ?IOCG defining features and occurrence ?Variable exploration characteristics ?Extracting value (gold metallurgy) ?Recent exploration experience(case study)

Apr 1, 2005

By Yuki Tsunazawa, Sho Fukui, Chiharu Tokoro

"A milling process is one of the important unit processes in mineral processing. In the milling process, the control of particle size distribution is necessary for the later physical separation process. Since the milling process is strongly affected by the equipment designs, operation conditions and raw materials, the control for particle size distribution of milling products is mainly based on empirical rules. Recently, the discrete element method (DEM) has been widely used as an effective tool to investigate the behavior of grinding media. Although the behavior of grinding media can be accurately simulated, it is not well-established the way to predict particle size distribution after milling by the DEM simulation.The objective of this study was to develop a new method to predict particle size distribution in ball milling using the DEM simulation. To predict particle size reduction, a correlation between experiments and the simulation was investigated in various operation conditions, that is, wide range of the rotation speed and the filling ratio of grinding media. In experiments, after lime stone was ground, the average and variance of particle size distribution were evaluated using some kinds of distribution equations. In the DEM simulation, direct simulation of particle disintegration in milling process is generally very difficult because of huge computational load. Therefore, collision energy between grinding media balls orgrinding media ball and wall was used as a factor of particle disintegration.As a result, a good correlation between experiments and simulation was obtained. In addition, the particle size distribution in ball milling could be predicted using this correlation. Therefore, these results indicated that the use of the correlation between experiments and the DEM simulation was an effective approach of predicting the particle size distribution in milling process."

Jan 1, 2016

By W. B. Evans, D. P. Taylor

"ANFO has two major disadvantages as an explosive low density and no water resistance. ANFO can be blended with more dense, water-resistant explosives to form ""Heavy ANFO"". The use of emulsion or slurry explosives as a matrix is an attempt to correct deficiencies on the basic ANFO while maintaining cost effectiveness.This paper will deal with four main topics.1. Product description, general properties, strengths and weaknesses.2. Technology of ""Heavy ANFO"" , the emulsion matrix concept and the range of products.3. Relative performance and economics in various rock types.4: Current status in Canada and worldwide, and the expectations for future use.IntroductionANFO has been in use for roughly three decades and remains the explosive of choice where conditions are suitable. ANFO has not become the universal explosive - despite its undoubted superiority in cost effectiveness - because it has serious flaws as an explosive. The most serious of these flaws are the low density and absence of water resistance in ANFO. Low density implies a low concentration of explosive energy in a borehole. The amount of energy available can be increased by. adding an energetic material, generally aluminum, or by drilling more holes. Both solutions add considerably to the over-all costs. The absence of water resistance in ANFO is inherent and can only be overcome by changing the fundamental nature of the product. The history of research in the explosives industry since the advent of ANFO is mainly the story of the various attempts to overcome one or both of ANFO's shortcomings.Many technologies and products have been developed to compete against ANFO, among them slurries, emulsion s and the so-called Dense ANFOs (ANFO with an extra nitroalkane liquid sensitizer). None of them was cost-competitive with ANFO so their market penetration has been limited to wet holes or specialized applications. The exception to this result is Heavy ANFO. The aim here was to have the best of both worlds, the high density and water resistance of emulsions or slurries plus the low cost of ANFO. The concept is very simple. ANFO is about 50 % air, roughly 30% in the prills and 700,10 between the prills . The air in the prills provides the necessary sensitivity but the air between them is waste volume. If one fills this volume with a high density, waterproof product, the resultant mix will be denser and more water resistant than ANFO and with very little added cost. This basic concept was invented by B. Clay in the 1970s and is covered by Canadian Patent No. 1 115 959. The water resistance and/or density of the mix can be tailored by changing the emulsion level. Because Heavy ANFO is relatively inexpensive while providing good in-hole densities and water resistance, it can compete successfully against all other bulk products. It competes against ANFO and Al / ANFO by allowing pattern expansion and reducing over-all costs while it competes against emulsions and slurries on price."

Jan 1, 1987

By J. E. Zajic, E. A. Sullivan, T. R. Jack

"The release of vanadium, iron, nickel and titanium from the cokes produced in the upgrading of Alberta oil sands bitumen has been assessed for simple chemical leaching processes. Flexicoker coke (Exxon Engineering and Research) has been found to be quite amenable to the recovery of vanadium as well as nickel, iron and some titanium by these techniques, whereas fluid coker coke (Syncrude) and delayed coker coke (Great Canadian Oil Sands) are relatively intractable under the mild conditions employed. The factors affecting the extent of vanadium release are discussed in terms of the surface area accessible, the wettability of the material, and the chemical and physical composition of the coke particles in each case.A novel biologically assisted heap leaching procedure for f1exicoker coke is also described, based on the growth of the chemolithotrophic bacteria, Thiobacillus thiooxidans A TCC 8085, on elemental sulphur added to the coke."

Jan 1, 1980

By B. R. Schneiders

"Atikokan is 200 km west of Thunder Bay and earned its mining fame from the discovery of the Steep Rock Iron Range in the late 1930s. Gold, however, was discovered in the Atikokan and Mine Centre areas in the late 1800s and eventually led to one of Ontario's first gold camps, and a total production of approximately 52,000 oz of gold and 174,000 oz of silver from 218,000 tons milled.The general geology of the area consists of Early Precambrian rocks of the Wabigoon and Quetico subprovinces, separated by the east-trending Quetico Fault. The Wabigoon Subprovince, to the north, consists of metavolcanics, minor metasediments and granitic batholiths. The Quetico Subprovince consists of metasediments and granitoids. Small ultramafic plutons occur throughout the metasediments.Within a 50-km radius of Atikokan, more than 50 gold occurrences, prospects and past producers have been discovered since the 18oos. The Atikokan Gold Study performed by the Ontario Geological Sur vey (Wilkinson, 1980, 1982) defined three types of gold mineralization in which gold is concentrated in quartz and quartz-carbonate veins:I) Metavolcanic-Hosted, Stratabound Type-associated with altered felsic fragmental units and chemical sedimentary rocks; possible gold mineralization source rocks. The mineralization is due to metamorphogenic (epigenetic) enrichment. Associated with dynamic metamorphism events and/or felsic intrusive events.2) Marmion Lake Batholith Type-occurs within the gneissic core of the batholith associated with north east-trending lineaments, representing faults or shear zones. Mineralized veins are related to several periods of deformation and shearing, suggesting that metamorphogenic veins were produced during dynamic metamorphism.3) Contact Zone Type -occurs in the contact zone rocks between gneissic batholiths and meta volcanic belts. Hydrothermal solutions produced during several deformational periods acted to leach and concentrate gold mineralization. Localized, discontinuous shear zones host the epigenetic (metamorphogenic) veins.Twenty-one properties in the area were mapped and sampled, and researched petrographically and geochemically. Geological data from the Atikokan Economic Geologist Program of the Ontario Geological Survey are used in discussing the types of mineralization, genetic models, and exploration targets and techiques."

Jan 1, 1983

By S. Dallaire

With the attainment of high temperatures it becomes possible to process any kind of material (particularly ceramics) in their liquid state. In the plasma spraying process, the material to be sprayed is rapidly heated until it is molten and is propelled by high velocity gases onto a surface where it adheres, to give protective coatings for a wide range of applications. The method could be considered as one of the most versatile and rapid to build up thick deposits (of plastics, metals, ceramics, cermets) and also free-standing artifacts for particular requirements without resorting to lengthy forming and sintering studies. Although plasma spraying is at the production stage in industry, advanced processes have also been developed for economically producing a wide range of new materials. This paper illustrates the benefits of the process and evaluates the challenges it represents.

Jan 1, 1987

By J. E. Marshall

"The concept of employing a project management team to coordinate all aspects of the construction of a new resource development has gained wide acceptance. This team can be formed from within the staff of large mining companies or contracted from major engineering firms and consultants. The mandate of the project managers usually terminates on successful startup of the operation. For frontier mineral developments in the Canadian Arctic or in the developing countries, startup and the initial year of operation represents the period in which the project is most vulnerable to technical, political and managerial problems. A complete change of the management team or the retention of the construction project managers and the resulting cost combined with the breakdown of organizational accountability within the operating staff .are unnecessary management problems.Independent project management services provide the commitment necessary to sustain the continuity of management through all project phases. Efficiency and the ability to make decisions quickly are characteristics of the many successful small mining companies. These qualities are necessary in the project management group, which will be responsible for up to 90% of the preproduction costs.Continuous project management in the construction and operational phases of a mineral development are common in the iron ore industry, but remain anomalous in the base metal, energy mineral and industrial mineral fields.The Nanisivik project on Baffin Island in the Canadian Arctic is used to illustrate the advantages of total project management through construction and operation.Total project management has further potential for foreign interests and financial and utility organizations desirous of participating in the Canadian mining industry, but with no direct involvement in the construction or operating management. Participation agreements in the operating phase of a project can be negotiated to have management fees related to both the production and the profits of the enterprise."

Jan 1, 1980

By Robert W. Plummer

"This paper describes the use of Geographic Information Systems (GIS) as a tool for mineral exploration by using the Eskay Creek area of northern British Columbia as an example. Data entry, analysis and output are discussed. Examples of some of the capabilities of the technology are presented.The main benefit of the technology is being able to perform complex and sophisticated searches of large and diverse data sets to highlight exploration targets. A GIS is a powerful data management tool that can be used in mineral exploration. It is a computer based system that is designed for the collection, storage and analysis of objects and phenomena where geographic location is an important characteristic. The main function of the GIS is to produce information for the geologist from a variety of sources (geology, geophysics, geochemistry, mineral deposits and so forth) quickly and efficiently. This allows the geologist to examine large amounts of data in a fraction of the time than can be done using conventional manual methods."

Jan 1, 1992

By A. Sacit Saydam

"Induced polarization/resistivity and magnetometer surveys have been carried out over the Casmo molybdenite deposit in mountainous terrain of northern British Columbia. Molybdenite occurs in quartz-bearing fractures with or without pyrite along a zone of hydrothermal alteration and intense fracturing, believed to be a northerly dipping fault zone, within medium-grained equigranular and porphyritic quartz monzonite.The molybdenite-bearing zone is characterized by a significant resistivity low, a metal factor high and a subtle IP low flanked by highs outside the mineralized area. Magnetic trends, indicated by a magnetometer survey, generally parallel the zone and strike direction of the different intrusive phases, and have been helpful in delineating contacts and faults in the area.IntroductionThe Casmo molybdenite deposit is 6 km southwest of the asbestos mining town of Cassiar in northern British Columbia, at an elevation of 1,550 metres. Molybdenite was first discovered during the early 1950s and the first important exploration work was done in 1964. Between 1964 and 1971, about 25,000 feet of drilling was done by various operators, as a result of which 33.7 million tons of molybdenite ore was drill indicated at a grade of 0.123%. In 1979, Shell Canada Resources entered into an option agreement with the former operator, New Jersey Zinc Corporation. Shell completed 27,000 feet of diamond drilling between 1979 and 1980 and ha s reported 75 million tonnes of drill-indicated ore with an average grade of 0.13% MoS2• This paper is a case history of IP I resistivity and magnetometer surveys done over the Casmo deposit during 1979 and 1980."

Jan 1, 1983

By M. Hozayen, E. S. Radwan, P. A. Nawrocki, A. Jebbouri

"A major geomechanical study was conducted for one of the UAE onshore oil fields with the purpose of studying reservoir rock properties and stress distribution, based on which a 3D coupled reservoir geomechanical model was built. This model was later used for wellbore stability analysis and for analyzing the effect of fractures on future reservoir production performance, including fracture deformation and permeability evolution occurring due to reservoir depletion and resulting changes in local stress field. The subject of this study was a complex fractured Upper Cretaceous carbonate reservoir characterized by high degree of heterogeneity, both vertically and laterally. Wellbore instability related drilling problems were encountered while drilling the wells in this field. The problems were mainly in drilling the horizontal wells, including breakouts and mud losses. Experimental results of laboratory tests are summarized in this paper whereas wellbore stability analysis and formulation of a 3D geomechanical model that was built for that purpose is summarized in a sister paper (Part II).A suite of tests reported includes tensile strength, uniaxial and triaxial compression and permeability under stress at simulated reservoir conditions. All tested rocks have been grouped into twelve test units and reservoir geology, rock types and challenges related to designing a viable sampling and testing program for a big reservoir are discussed first followed by sample selection criteria and details of the testing program. All test units showed brittle behavior at zero confinement and some samples showed similar behavior at low confining stresses. With confining stress increase, the behavior gradually turned to plastic but some samples showed features of ductile behavior even at low confinement.Obtained experimental data have been summarized in the form of strength criteria and correlations. The Mohr-Coulomb strength equations were obtained for each test unit and also for the averaged values. It was noticed that triaxial compressive strength (TCS) increases with decreasing porosity or increasing density but their influence on TCS is getting smaller with confining pressure increase. Good correlation of porosity and density with Young’s modulus, Poisson’s ratio, unconfined compressive strength (UCS), friction angle, cohesion and tensile strength has been noticed and there was an increasing trend between the confining pressure and TCS. Rock type (mud or grain supported) was not influencing the TCS as much as porosity and density and the two lithologies encountered affected TCS approximately in the same way. These results and correlations are summarized and explained in this paper. They were further used in the numerical modelling part (Part II) of this paper, Hozayen et al. (2015). It is also concluded that rock lithology is not a decisive factor and mechanical properties of tested rocks should be rather considered dependent on porosity and permeability. This helped greatly in reducing the number of tests that had to be performed."

Jan 1, 2015

By R. B. Smith, D. C. Brady

"A review of the major renovation of the fifty-year old C-I headframe facilities at NERCQ's Con Mine, Yellowknife, N. W.T. is provided. The project was complete with only two 3-day shutdowns of the facility .Work consisted of four major phases: structural reinforcement of the adjoining mill building prior to dismantling; relocation of virtually all mine and mill utilities which transited the headframe collar en route from the adjacent powerhouse; dismantling of the entire headframe facility and portion of the mill building, including the removal of asbestos siding; and erection of a new headframe, idler rower, collarhouse and mill wall.This paper describes the work and methods used by NERCQ, J.S. Redpath Mining Consultants Limited, Acres International Limited, and others to bring the project to a successful completion. The history of the project is discussed from the planning phase through construction, including; design, procurement, and construction scheduling. The paper discusses the unique elements of the project, the problems encountered, and the methods used to achieve success.IntroductionThe Con Mine is a 800 tpd gold operation located in Yellowknife, Northwest Territories. Originally owned and operated by Cominco Limited , the Con Mine was sold in December 1986 to NERCO Minerals Company, and officially renamed NERCO Con Mine, Ltd. The Con Mine has been in operation for over 50 years. The first gold brick ever produced in the Northwest Territories was poured at the Con Mine in 1938. The original C-1 shaft was sunk in 1937 to a depth of 235 ft. In 1941 the shaft was deepened to a depth of 950 ft, and the original timber head frame was replaced with a steel structure. Following the discovery of the Campbell Shear in 1946, the C-l shaft was again deepened to its present depth of 2443 ft. Over the years, mine production gradually moved deeper and further from the C-l shaft."

Jan 1, 1991

By R. Bonnar, R. J. McH. Clark

"The Cheminis gold mineralization zone is approximately 6.5 km west of the Kerr Addison Mine along the Larder Lake Shear Zone, in the southern part of the Abitibi Greenstone Belt. The zone is very similar in appearance to the flow ore at the Kerr Addison Mine and occurs at the same stratigraphic position. Drilling has demonstrated that the gold mineralization at Cheminis persists to a depth of over 3000 ft .The mineralization is hosted by a pyritic, tuffaceous sediment which occurs within a sequence of volcanics and sediments which have been pervasively carbonatized. The gold is largely enclosed within pyrite grains and the amount of gold in the layers of pyrite increases in the layers closest to a graphitic f ault zone.It is suggested that the gold mineralization may be primarily related to the syngenetic sulphide concentrations formed during fumarolic activity on the seafloor along the Larder Lake Shear Zone. At a later stage a hydrothermal event associated with alkalic volcanism may have resulted in regional carbonatization and further concentration of the gold in the vicinity of fault zones."

Jan 1, 1987

By Rae Simpson

"This paper provides insight into the elements of computerized maintenance systems and identifies some of the factors which influence their effectiveness. The paper describes what to expect in terms of benefits and problems, the nature of effective computerized maintenance systems, some of the systems available and a process for selecting a system for your organization.The paper will be of interest to mining company executives and maintenance or computer personnel who are involved with, or contemplating, the introduction of computerized maintenance systems.IntroductionIn the drive to improve profits in an increasingly competitive world, mining companies are now using some of the most sophisticated equipment available. The introduction of large and complex equipment such as drag lines, haul trucks, and high-capacity milling equipment has resulted in order-of magnitude improvements in productivity. However, this productivity is now, more than ever, dependent on the continued operation of the equipment. A prolonged breakdown of a critical component can have a significant effect on companies' bottom-line results. As more technologically sophisticated equipment is introduced, maintenance costs become an increasingly important factor for mining companies.Fortunately, sound modern management principles are being used more often in maintenance departments. Progressive maintenance managers are turning to computers to help manage the myriad of details associated with running a maintenance organization.Some maintenance departments in larger mining operations would find it difficult, if not impossible, to operate at current productivity levels without their computer systems. Unfortunately, some other companies gain very little from their computerized systems and would probably be better off without them.How can you be sure that computerized maintenance will improve the maintenance picture for your company? What benefits can you expect to achieve? How do you go about selecting a maintenance system for your organization? These are some of the questions facing industry managers and executives today. In the following sections, we will provide some guidelines and insights to help address these challenges."

Jan 1, 1988

By D. V. Krefting, D. R. Bennett

"The Cyprus Anvil Mining Corporation established a lead-zinc mine and concentrating plant at Faro in Yukon Territory in 1969. Following some 12 years of continuous operation from a single pit adjacent to the concentrator, the company decided to expand operations into two additional areas on the Vangorda Plateau. The two new deposits, known as Grum and Vangorda, are located some 15 kilometres from the existing concentrator.Confirmation of mining feasibility was followed by determination of the most practical and economical method of transporting the raw ore from the new mine sites to the existing concentrator. This analysis was carried out in two phases. The first phase reviewed the feasibility of alternative transportation systems on an 'order-of-magnitude' cost basis. This work identified systems worthy of more detailed examination. The second phase examined the preferred alternatives in greater detail.Initially, operating principles and parameters were established and catalogued. Then, based on these criteria, complete systems were developed utilizing alternative modes of transportation . In the overview analysis, some transportation modes were judged impractical and discarded, 'order-o f-magnitude' costs were developed for other systems and the most costly were eliminated . In the detailed study, the favourable systems were examined in depth which required development of accurate capital and operating costs, consideration of environ- mental impacts and an assessment of intangibles associated with the operation of a new development."

Jan 1, 1984