Search Documents

By B. Fang

Electrochemical behavior of an X-80 pipeline steel, including frequency-sweep electrochemical-impedance spectroscopy (EIS), time-sweep EIS at a constant frequency and open-circuit potential (OCP) monitor, was investigated using four-point bending specimens subjected to a stress-corrosion cracking (SCC) test in a near-neutral pH environment, The capacitive loop became smaller with test duration, revealing an increase in the corrosion rate, The resistance obtained in the constant-frequency EIS test showed two regions, of which the region with a remarkable decrease in resistance transformed into a region of slow decrease, whereas the capacitance increased with test time indicating that iron dissolution was fast at first, and then a corrosion product or film formed and covered the surface, leading to the pitting formation.

Jan 1, 2005

By Lou Covello

Bow Valley Industries Limited i conducting an on-going exploration program for gold in Archean, turbidite-hosted iron formations near the Lupin mine on Contwoyto Lake, orthwe t Territorie . Exploration philosophy and practice are modelled on the Lupin deposit where 70% of the gold occurs within laminated pyrrhotitechert. sulphide facie iron formation. Thi i intimately associated with barren to low-grade silicate facie iron formation which i enclosed by predominantly argillaceou meta ediment . This type of mineralization i amenable to exploration through an integrated program of geological and geophy ical surveying, consisting of the following: i) Geological urvey both regional and local to outline area of turbidites and a ociated iron formation. Structural and tratigraphic trends documented during this phase are useful in determining eventual grid configurations. Grids are then mapped and ampled at 1:2000 cale. ii) Magnetometer and gradiometer urvey at the ame scale define strongly magnetic diabase dyke and erratically magnetic portions of iron formation. iii) VLF-EM survey are u eful in outlining conductive trend invariably as ociated with sulphidic or graphitic phase of iron formation. iv) Geological updating and ampling of iron fom1ation based on the geophysical su rveys. This is necessary for the production of a final geologic map and a an adjunct to drill target election. In problematic instances self-potential urveys have documented the pre ence of non-conductive sulphide accumulations, and horizontal loop EM surveys have been used to determine conductor geometry and quality. Target selection is based on a synthesis of the information from all of the above surveys with the results of no single survey being critical to drill decisions. The program is designed to provide first-pass, detailed , cost-effective ground coverage of large areas of highly prospective geology.

Jan 1, 1986

By L. C. S. Dharmasiri, S. M. Shin, A. Senaputra, J. S. Sohn, K. H. Park, J. Avraamides

Reducing agents can be applied to leach metal values from natural and secondary resources such as laterite ores and deep sea manganese nodules and recycled materials such as spent batteries / catalysts which contain high-valent metal oxides of manganese, cobalt and iron. Selective leaching of some metals can be achieved by selecting conditions to control the saturated solubility and dissolution rates of metals from oxides or mixed metal/oxide matrices. The leaching results are rationalized on the basis of chemical species, Eh-pH diagrams and heterogeneous kinetic models. The role of reducing agents such as hydrogen peroxide, sulfur dioxide and iron(II) sulphate, in acid, alkali and in the presence of complexing ligands such as ammonia for the improvement of the leaching of metal oxides and metals is discussed. Previous studies on acid leaching of metals from nickel laterites, manganese nodules and spent catalysts/batteries in the absence or presence of reducing agents show that the rate controlling step involves the diffusion of protons through a thickening product layer on the particle being leached. It is shown that the leaching of nickel and cobalt from manganese nodules and zinc-carbon batteries in ammoniacal sulphur dioxide solutions also obey shrinking core kinetics.

Jan 1, 2014

By V. H. Valenzuela

Materials in process or in stocks are quite relevant items in almost every plant, particularly in mining operations, where efficiency in rate of recovering material of interest becomes a key issue when production costs are evaluated. A manager requires information to do an effective use of the resources, especially when raw materials are involved. Losses associated to leaking, efficiency in the transformation process, performance of equipment, and operating conditions are a short list of items which must be properly identified and evaluated. Operations supervisors require information in order to keep key process variables under control. Because of these information needs, it is absolutely necessary to carry on a series of activities related with installation and maintenance of measuring equipment, sampling equipment, sample preparation, chemical analysis, statistical analysis, data handling and reports generation. These pieces of data must be managed on a wise manner in order to get the most of it, keeping always on mind data reliability. Normally, information related with metallurgical balance and even more, the metallurgical balance concept, is handled under an accounting criteria which does not allow dealing with the real world. This situation happens because the criteria utilized do not consider aspects such as bias and uncertainty associated with every measurement that affect the quality of the information and therefore conclusions drawn from it. The purpose of this paper is to give a few rules, necessary to follow, in order to develop an adequate Metallurgical Balance System for an operational point of view. The Gaussian approach for error propagation is used as a basis, allowing one to know the actual uncertainty of the balance and the way how it can be improved. A few real applications of this concept are listed, detailing experiences obtained from practice.

Jan 1, 2007

By Greg Gosson, Larry B. Smith

"These are heady times for the mining industry, with strong metal prices, investor enthusiasm for the junior explorer and ready access to finance for mineral projects. Many projects were shelved in the past because of technical deficiencies — insufficient tonnes or grade, metallurgical problems, the deposit was too deep or too narrow, or the project was physically or economically under water. With the possibility of sustained metal prices, now is the time for those previously “challenged” projects to be re-evaluated and financing sought for continued development. The question is, do these deposits have reasonable prospects for economic extraction, as required by all mineral resource reporting codes? NI 43-101 defines a mineral resource as that portion of the mineral inventory that has reasonable prospects for economic extraction. However, a mineral resource is not simply an inventory of all blocks above a given cut-off grade. The spatial distribution and geological and grade continuity must also be considered. The qualified person (QP) must consider factors significant to project economics at the mineral resource estimation stage, and not just when qualifying mineral reserves. CIM Best Practice Guidelines for estimating mineral resources require the factors significant to project economics be current, reasonably developed and based on generally accepted industry practice and experience. In establishing the cut-off grade, it must realistically reflect the location, deposit scale, continuity, assumed mining method, metallurgical processes, costs and reasonable long-term metal prices appropriate for the deposit. Variations within the resource model (rock characteristics, metallurgy, mining methods, etc.) may necessitate more than one cut-off grade or economic limit in different parts of the deposit model. There must be sufficient knowledge of the metallurgical characteristics of the deposit, which should be supported by preliminary metallurgical test results."

Jan 1, 2003

By Robin Belley

Outline Introduction Wabush Mines HistoricalBackground Mine and Concentrator at WabushMines High Intensity Magnetic Separators (HIMS) Development of the Manganese Removal Process Pilot Plant Testing Phase Manganese Removal Line 1 Coming Phase: Manganese Removal Line 2 Manganese Concentration Process Development Historical Background 1847: Creation of the Cleveland Iron Company1850: Opening of its first iron ore mine in the Upper Peninsula of Michigan 1965: Beginning of Wabush Mines at Scully Mines, Wabush, Labrador. 1980-1990: Questions raised about how to exploit Scully high Mn Ore (> 2%)Part of the available ore is not saleable due to too high a level of pyrolusite (MnO2) Adding this ore to the resources would be valuable (longer mine life and lower stripping ratio) 1990s: Testwork for Manganese removal Many different processes are studied over more than a decade High Intensity Magnetic Separators (HIMS) are identified as the best technology for Mn removal 2007: Pilot Mn removal line installed Testing carried out through 2007-2008 First Production Line is ordered (2008) 2009: Cleveland Cliffs (now Cliffs Natural Resources)acquire the remaining part of Wabush Mines 2010: Mn Removal Line 1 construction & commissioning Summer 2011: Mn Line 2 Construction

May 1, 2011

By M. Massinaei

Recently constructed circuits have included multiple stages of columns in a variety of applications, from roughing to cleaning. The Miduk copper concentrator (in south-eastern Iran) is one of the unique mineral processing plants which use column flotation cells as rougher. As the bulk of final concentrate is produced by rougher columns, optimized metallurgical performance of these cells is crucial. This paper will present the study and optimization of, a froth washing system of columns. For this purpose, the cross-sectional area of orifices was increased and their orientation altered. Concentrate assay for copper and silica, in addition to bias rate were found to be the assessment criteria. Modification of the wash water system resulted in increasing the purity of rougher and final concentrate. Negative bias and short-circuiting of wash water into the concentrate launder were the main causes of improper froth zone washing in the former system.

Jan 1, 2007

By PAUL L. DEAN

Industrial mineral deposits are widespread in Newfoundland and Labrador and a variety of commodities are produced. The province has the only pyrophyllite mine in Canada and also produces asbestos, gypsum, silica, barite, limestone, gemstones, cement and other structural materials. Large reserves of these and other industrial minerals are known and several deposits are likely future producers. Most producers are wellestablished and have large tonnages of ore reserves.

Jan 1, 1984

By Yan Yang

The Jinfeng gold mine is one of the three gold mines that Eldorado Gold has in China and it is the second largest gold mine in China. The mine is located in a relatively remote and mountainous area in the southwestern Guizhou province. The orebody is similar to the Carlin type deposit in Nevada. The mill throughput was designed to treat 3,600 tones per day. The ore comes from open pit mining and underground mining, and is fed to one-stage jaw crushing. The crushed ore is stockpiled, reclaimed and then fed to the SABC grinding circuit. After classification with hydrocylones, the ore is floated, and the resultant concentrate is oxidized biologically in a process known as BIOX®. The oxidized concentrate is then washed in a CCD circuit and finally leached with cyanide in a CIL circuit for gold extraction. Jinfeng produces about 180,000 oz of gold per year. This paper introduces operations and modifications of SABC circuit over the past three years, and then describes some technical characteristic of the SAG mill and other circuits in the processing plant. Major modifications and improvements on the SABC circuit are described in the paper, including: 1. Impacts of grinding ball and mill liner with respect to material selection, quality, hardness, manufacturing methods, and interactions between mill liner and grinding ball. 2. Effect of milling operation parameters on milling efficiency. 3. Impacts of SAG mill scats and modifications of grate size to improve mill throughput. 4. Design and construction of a pebble crushing system, and recycle the crushed scats to the SAG mill to improve mill throughput. With the above-mentioned modifications, 20% increase over the design in mill throughput has been realized over the past three years, and operating cost has been significantly reduced. However, some issues still remain, and thus process modifications and technical innovations are still needed.

Jan 1, 2012

By J. M. Carr

The history, geological setting and local geology of the Magnum vein system, 100 miles west of Fort Nelson in northeastern British Columbia, are described. The system comprises a number of quartz-ankerite veins, mineralized with chalcopyrite and lesser pyrite, occurring in a steep northeastly zone of deformation and subsequent dike intrusion within otherwise little-deformed Precambrian sedimentary rocks. In April of 1970, Churchill Copper Corporation began producing copper concentrates in a 750-tpd mill fed from the Magnum mine.

Jan 1, 1971

By James J. Scott

"In the two years since their introduction, Friction Rock Stabilizershave replaced40 per cent of the previously used fixtures in the metal and non-metal mines in the United States. The Friction Rock Stabilizer, or ""Split Set "" , is a mechanical rock stabilizing system which uses friction to prevent rock movement . The Split Set is a tapered, rolled, steel tube that is slotted along its length. As it is driven into a drilled hole smaller than its diameter, it compresses, pre-loading the surrounding rock. This paper discusses the uses and acceptance of the friction rock stabilizer in mines in the United States. IntroductionFriction Rock Stabilizers, commonly called Split Set™· Stabilizers, have been under development by the author and Ingersoll-Rand Company since early 1973. Five years of intensive laboratory and field testing led to their introduction to the metal mines in the United States in the fall of 1976. Actual sales started in February of 1977and, to date, over five million units have been marketed to metal mines. The present rate of usage is near 3 V2 million units per year, which is approximately 50070 of all roof fixtures used in the United States metal mining industry,Richard Hoppe, senior editor of Engineering & Mining Journal. , in an article in the February 1979 issue entitled ""Winning the Battle Against Bad Ground"", said: ""In hardrock mining operations in the western U.S., particularly underground uranium mines where exceedingly difficult ground is common, no roof support system has been accepted more quickly than the Split Set friction bolt invented by Dr. James J . Scott and developed by Ingersoll-Rand Co."" This paper describes how Friction Rock Stabilizers function and presents technical data to show the uniqueness of such systems."

Jan 1, 1980

By Robert B. Wickham

"American Barrick has always balanced its aggressive operating approach with a conservative financial strategy. In fact, what enables their mining team to pursue such aggressive plans with confidence is the conservative financial strategy adhered to by the company. These policies are built on a prudent mix of gold linked financings, equity and gold price hedging.This paper outlines these policies and focusses in particular on American Barrick's gold price hedging program.IntroductionThe company's balance sheet at the end of 1990 clearly shows the wisdom of its conservative policies. Total assets have grown to over US$1 billion; cash has grown to US$312 million and shareholders' equity to US$645 million. All amounts included in this paper are quoted in U.S. dollars. Increased gold production and an effective gold price hedging program also combined to produce record income from operations, earnings and cash flow in 1990.The first half of 1991 is also indicative of the benefits of the company's conservative financial policies. Increasing production, together with its comprehensive gold hedging program, has generated increased earnings, even in a period of falling gold prices.All year-over-year numbers for the first six months are up. Gold production was 36% higher; earnings of $40.2 million $ 0.30 per share - were 46% higher than 1990.Barricks revenue continued to increase despite gold prices remaining unchanged during 1990. Barrick's hedging policy protects the company from falling gold prices on the basis that the upside looks after itself. Their hedging program - including various goldlinked fmancings - enabled Barrick to realize an average price of $437 per ounce of gold sold in 1990, compared with the Comex average gold price for the year of $384 per ounce."

Jan 1, 1991

By William C. Boggis

EKATI? Diamond mine is located 300km northwest of Yellowknife and 200 km south of the Arctic Circle in the Northwest Territories of Canada. The site is a remote tundra area with continuous permafrost and is in the Canadian Shield. EKATI? is the first diamond mine in Canada and is operated by BHP Diamonds Inc., which is a part of BHP Minerals. BHP Diamonds Inc. is an incorporated company based in Vancouver, BC. The mine is a joint venture of BHP Diamonds Inc. (51%), Dia Met Minerals Ltd. (29%), Charles E. Fipke (10%) and Dr. Stewart L. Blusson (10%). The mining area lies within the 10,960 ha land leases held by the joint venture. The total claim block covers 344,000 ha. To date over 136 kimberlite structures have been identified within the claim. Five of these provide the basis for the present mine plan with three others identified for future inclusion. At full capacity the mine will produce 4.5 million carats per year, approximately 4 % of world production and employ approximately 600 people, with over 33% being Aboriginal from the Northwest Territories.

May 1, 2001

By Walter Greaves

THIS paper describes a series of tests performed at the Hollinger mill during the past four years, in which both metal and rubber-lined pumps were used for pumping sand and slime. While conditions will not be the same at other mills, it is felt that the information gained from the tests should be of value to other operators and of assistance to them in selecting the most efficient size of pump and kind of lining for economical operation. For the successful operation of pumps with rubber linings there are certain conditions, which, if recognized at the outset, will save the operator a good deal of work and trouble. First is the necessity of keeping sharp pieces of steel, or anything that might cut the lining, out of the pumps. This can be effected by placing screens in the proper locations. Second is to recognize the fact that the rubber lining of the shell, and the rubber cover of the impeller, are subjected to very different conditions. The shell lining, :being at rest and well supported by the metal case, has a relatively easy job compared ? with the impeller covering, which is subjected to centrifugal force and has a tendency to tear itself away from the metal core. Also, the pulp travels through and past the impeller at a high velocity. These two factors, centrifugal force and velocity of the pulp, would appear to set a limit to the speed at which, for a given set of conditions, it is economical to run a rubber-covered impeller. Therefore, a pump should be large enough for the work to be done. To get the best mechanical efficiency, it must be operated somewhere near the limit of its capacity, but this may not give the best overall cost, because the saving in power, due to the high efficiency, may easily be lost through excessive wear on the lining. It would appear that this condition is more critical in a rubber-lined pump than in one lined with metal.

Jan 1, 1939

By Wallace R. Horn

"MR. CHAIRMAN AND GENTLEMEN :I begin this talk by making a couple of comments which are of the nature of disclaimers.Firstly, and as the Chairman has otherwise indicated, I was neither ""born into"" nor have I spent more than a few years of my professional life in the mining industry. I mention this because many might, and perhaps rightly, consider that an added qualification in presenting a report of what the industry has accomplished. Indeed, I am not here to blindly defend all of its actions and inactions in respect to environmental control over the years. Nor am I here to seek absolution of the industry's past transgressions - if indeed that is the word. Mistakes might be a better one. I concluded some time ago that the effects of those mistakes are too difficult to assess against the sea of errors of our total society. I should mention too that I am not an environmental engineer or specialist - only a portion of my interest is involved with this field. Perhaps this permits a perspective which allows a more accurate and objective view.One further comment here. My job today, as I understand it, is to generally report upon the nature and extent of the response of the metals mining industry to control of the environment. In the case of an industry operating at more than a hundred locations and for various reasons at various stages of progress, it is not an easy job. On the other hand, I wanted to avoid the use of generalities because, especially within the context of environmental or ecological opinion and of the practice of condemnation of industrial segments, I think we've had about enough of generalities until we know far more than we do.Finally, I am quite aware that a statement of future plans to achieve environmental control does not impress or satisfy as many people as it may have done some years ago. Public opinion demands to know what is currently underway, today."

Jan 1, 1972

By F. Richards

"The property of the Cariboo Gold Quartz Mining Company; Limited; is in the Wells-Barkerville district of Cariboo mining division. It consists of a group of 106 Crown granted mineral claims and fractions; and extends for over 6 miles along what is termed the Barkerville gold belt. The main portal and mine camp are half a mile south of Wells; which lies at the northeast end of Jack of Clubs lake and is reached by a 55-mile motor road from Quesnel; the northern terminus of the Pacific Great Eastern railway.Gold-bearing quartz veins were discovered on the surface in various parts of the property by different prospectors as far back as 1877, but the work that led to the formation of the present company was performed by Al Sanders in the year 1926. Sanders dug trenches and drove small adits on quartz veins containing gold above what is now known as the Sanders zone. Very little underground work has been done beneath the earliest known discovery-the B.C. vein. The Cariboo Gold Quartz Mining Company was formed in the autumn of 1926. The total production of gold from its beginning in 1933 to the end of 1944 has been as follows:"

Jan 1, 1954

By Rafic Moubarac

FRP (Fiberglass Reinforced Polyester) equipment has been used in different and several applications during metals processing and extraction, and the hydrometallurgical process. Case histories of such equipment will be shown of major projects worldwide.

Jan 1, 2015

Over five decades ago Kitchener et al. in England and La Mer and Healy in the US were advancing our understanding and application of flocculants, primarily related to water treatment and filtration of sludge. This paper identifies the beneficial uses of flocculants in the mining industry and revisits some less common applications. Flocculants are used in unique ways in the mining industry: (a) to increase the effectiveness of sediment ponds to achieve discharge compliance; (b) to eliminate air emissions and costs associated with concentrate drying; (c) to reduce soil loss by applying a flocculant to erodible soils, and reducing wind and water erosion; (d) to remove/thicken metal precipitates in acid rock drainage treatment; and (e) to enhance clarification and thickening in mineral processing. The mechanism of how flocculants, coagulations and potentially-determining ions function is described and how their use can be controlled and optimized. The potential toxic effects of flocculants and coagulants when used to achieve effluent permit discharge compliance for suspended solids is discussed. A review of numerous best management practice (BMP) guidelines for the design and operation of sediment ponds treating mine site runoff to remove total suspended solids (TSS) and turbidity revealed an absence of a predictive methodology to address regulatory discharge compliance for TSS concentration, turbidity and flocculant-induced toxicity. An essential component of pond design is the need to determine whether flocculants and/or other settling aids are required based on the site-specific soil particle size distributions upslope of the pond. Procedures are provided to predict the need for settling aids and estimate pond discharge quality and downstream impact for TSS, turbidity, toxicity and sub-lethal toxicity. The need to develop BMP guidelines are discussed for (a) the application of flocculant to surface soils to reduce erosion, (b) the application of flocblocks to increase the ?sediment control? aspects of erosion and sediment control, as part of the mine site erosion control plan strategy and (c) the application of flocculant to silt socks to treat mine site runoff.

Aug 1, 2013

1. Scientific prospecting has had a profound and some-what unexpected effect on the world's supply of raw materials over the past twenty years. Where shortages were recently anticipated, abundance now prevails. It seems probable that, for the foreseeable future, adequate metallic resources will be found at costs well within the world's economic means. 2. The amount of research devoted to scientific prospecting has been extremely small in relation to the possible importance of the problem and to what could be done. It has been dominated by the thought of a dozen brilliant men, and true research expenditures have not amounted to more than a few million dollars. 3. An undue proportion of the expenditures have been for so-called geological research -mostly of a petrologial character. The results have essentially been of historic interest only. However, there has been some in-crease in genetic understanding, and this is of great importance for future resources. 4. Basic advances in mineral exploration have been made in detection techniques, generally called geophysics and geochemistry.

Jan 1, 1964

By K. Kudo

Magnesium rods of 99.95% purity and approximately 6 mm in diameter were continuously cast at rates of between 15 and 25 mm/min by a heated mould process and their mechanical properties evaluated. It was found that rods cast at 15 and 20 mm/min consisted of a single crystal, while rods cast at a speed of 25 mm/min were multi-crystalline and showed a unidirectional structure. Although room temperature tensile ductility to fracture varied widely, it was found that with an appropriate crystal orientation, cast rods can exhibit elongation by as much as 215%.

Jan 1, 2006