Search Documents

By F. Nava-Alonso, E. Pérez-García, A. Uribe-Salas, J. C. Fuentes-Aceituno, A. A. González-Ibarra, E. N. Castillo-Ventureño

"Precious metals cannot easily be recovered from tellurides by the standard cyanidation process. This work assesses the cyanidation of synthetic samples of precious metals tellurides and explores some alternatives for the leaching of these species (i.e. cyanidation in presence of lead nitrate and thiosulfate leaching). For this purpose, three chemical systems were studied: (1) cyanidation of silver telluride and the effect of lead (II) nitrate addition, (2) cyanidation at high alkalinity and high cyanide concentration of a gold-gold telluride sample containing tellurium and tellurium dioxide, and (3) thiosulfate leaching of silver telluride employing cupric sulfate as oxidant and EDTA as complexing agent for copper. Results showed that standard cyanidation dissolves 10.5% of silver from silver telluride in six hours, while with the addition of 100 mg/L lead increased the silver dissolution up to 100% in the same time. The standard cyanidation of the gold-gold telluride sample dissolves only metallic gold in six hours, while when cyanide concentration and pH were increased, gold and gold telluride were simultaneously dissolved. Finally, thiosulfate leaching dissolves 43.1% of silver from silver telluride in six hours.INTRODUCTION Precious metals tellurides are classified as refractory ores due to the difficulties associated with processing them by the standard cyanidation method. The increasing presence of gold/silver tellurides in some deposits around the world, specifically in Sonora, Mexico, requires new approaches to the cyanidation process, or the development of new leaching techniques. Treatments have been proposed for the recovery of gold and silver from their tellurides, including roasting, preoxidation, cyanidation with lead nitrate, and the use of leaching agents other than cyanide (Zhang, et al., 2010; Ellis and Deschenes, 2016). This work presents preliminary results of three options to recover precious metals from pure tellurides: the cyanidation of gold telluride at high cyanide concentration and high alkalinity, the addition of lead nitrate to the standard cyanidation process, and the use of sodium thiosulfate as leaching reagent."

Jan 1, 2017

By E. R. Packer

"The mill of Anaconda Britannia Mines is located on the eastern shore of Howe Sound, approximately 32 miles north of Vancouver, British Columbia. The mill has a daily capacity of 3400 to 3500 tons and at the present is treating chalcopyrite-pyrite ore from which only the copper mineral is concentrated. For a clear conception of concentrate filtering and shipping practice at Britannia perhaps a bit of past history should be related.For many years the mill concentrated copper and zinc minerals and intermittently a pyrite concentrate was produced. It was general practice to ship copper concentrate by towed barge down Howe Sound, across Juan de Fuca Strait and thence down Puget Sound to Asarco's smelter at Tacoma, Washington. Zinc concentrate was loaded in hopper bottom rail gondolas spotted on rail barges and towed to rail heads in Vancouver, thence by rail to Anaconda Reduction Works in Great Falls, Montana. Most of the pyrite produced was shipped by ocean freighters to Japan and Taiwan with an occasional barge load of 2000 to 4000 tons to nearby customers in Vancouver and the state of Washington.In recent years, because of smelter shut-downs for one reason or another, mostly strikes, a considerable amount of copper concentrates has been shipped by ocean freight to Japan and in 1971 several lots were loaded in gondola cars and shipped by rail to the Anaconda smelter in Anaconda, Montana, because Asarco's smelter was forced by municipal and state anti-pollution laws to limit the amount of S02 emission from the smelter stacks. Zinc concentrate production was halted in the early part of 1Y70 because of zinc depletion in the ores and pyrite production was stopped in May, 1971, because of a lack of markets.Filter equipment in the Britannia mill consists of conventional disc vacuum filters and reciprocating vacuum pumps. The copper concentrate filter was installed in 1923 as a 6 x 8'6"" American disc type manufactured by United Filter Corporation, The zinc concentrate filter, now converted as a spare for copper concentrates, is also a 6 x 8'611 American disc manufactured by Traylor Engineering and Manufacturing Company and was installed the same year. Formerly, there were, in addition, two 4 x 6' disc filters for pyrite and two 6 x 6' disc filters to de-water bulk flotation concentrates ahead of the regrind mills. Installed vacuum pumps were two Ingersoll Rand 22"" x 811 and one 22"" x 9"". One of the smaller machines has since been scrapped.At the time of the writer's transfer to Britannia in 1965, the entire filter system was operating as a unit using two vacuum pumps and a common filtrate tank with a 2"" SRL filtrate pump for five operating filters. The regrind and pyrite filters were in continuous operation and the co11p('r concentrate filter alternated with the zinc concentrate filter because both copper and zinc concentrates were transp0rted to storage by the same conveyor belt."

Jan 1, 1972

By Bergh. L. C.

On line monitoring and diagnosis systems of process operating performance are becoming an important part of industrial programs, leading to improve process operation and therefore product quality over time. In processes, such as the contact section of a sulphuric acid plant, a large number of input variables, highly correlated, are presented. These characteristics usually pose more difficulties in modelling the process for monitoring and diagnosis purposes. Multivariate statistical projection methods, such as Main Component Analysis, have been proposed to effectively deal with these situations. The application of these ideas to a section of a 2350 MTD sulphuric acid plant, located at the Caletones Smelter, including dry tower, gas blowers, catalytic reactor and S03 absorber processes, is discussed here. A PCA model with eight main components is used for monitoring and diagnosis of more than seventy operating variables. Hottelling's T2 and Q residuals test were used for detecting measurement problems in relevant variables, and for identifying which set of variables were responsible for driving the process outside its normal operating region. Furthermore, considerable information for the correction of the tested operating problems was given by the use of these techniques.

Jan 1, 2007

"Acid resistant brick lined autoclaves and related vessels are utilized in pressure oxidation for the recovery of gold, copper, and other metals. The combination of the corrosion resistant membrane, acid resistant brick, mortar and steel shell is a composite system that requires a sophisticated stress analysis. In order to obtain meaningful results both the model and physical properties of the materials must be carefully selected. Evaluation of the calculated results requires an understanding of both the failure mechanisms of ceramics and experience with the performance of existing lining systems.INTRODUCTIONAcid brick lining systems are used in pressure oxidation autoclaves and related vessels to provide thermal and mechanical protection for corrosion resistant membranes that are applied directly to the interior of the vessel shell. The acid brick and mortar must be resistant to the process conditions and must provide a mechanically reliable structure.The construction of lined vessels incorporates a wide range of materials that can include the carbon steel vessel, austenitic weld overlay, lead lining, organic membrane, ceramic brick, mortars and other alloy components. The physical properties of the materials can vary by orders of magnitude and when combined in the construction of the lined vessel create a complex composite structure. The materials may be bonded together or act independently of each other. Stresses are induced into the lined vessel include pressure, thermal expansion, chemical expansion and mechanical loads.The complexity of these systems makes it is very difficult to account for all of the variables in the structural analysis of lined vessels. Historically calculations were simplified and designers primarily relied on experience with previous applications.The greatly improved tools for Finite Element Analysis (FEA) available today allow for detailed calculation of the stresses imposed on the vessel shell and lining. Koning & Lauzon (2004) presented a paper on design fundamentals including a discussion on the application of FEA methods at Pressure Hydrometallurgy 2004 in Banff. When a designer carefully constructs a model and selects the correct materials properties for the calculations, meaningful and useful results can be achieved."

Jan 1, 2012

By E. L. Bruce

Red lake is a body of water some thirty miles in length lying about forty miles northwest of the outlet of Lac Seul. It forms one of several large lake expansions on a river which enters the English river from the north, twenty miles below Lac Seul. Before the construction of the National Transcontinental railway a long canoe journey was necessary to reach that part of the English river, and Red lake, two days travel beyond, was one of the furthest outposts of the trading companies in that difficultly accessible triangle of country between Lake Winnipeg, James Bay and the English and Albany rivers. The Hudson's Bay Company post at Red lake is said to be one of the earliest established in the district but there are no records at the post, and as the English and Albany rivers never were used to any great extent as travel routes there is no mention of the place in the diaries of any of the early explorers. Dr. Bell passed through Red lake on his excursion to the Berens river country in 1883, and a brief note mentions that Huronian rocks were seen. To Dr. Dowling, however, belongs the credit for the first thorough description of this basin of sediments and basic volcanics. In 1893 he followed the course of Dr. Bell's trip, of ten years previous, through Red lake to the upper part of the Berens river.

Jan 1, 1926

Mineral engineering is defined as those engineering activities that relate to the discovery, development and utilization of mineral resources. Using petroleum engineering as an example, it is shown that the breadth of the field to be studied is a major educational problem. Breadth of field is aggravated by the rapidity with which technological demands may change. At present, special short courses serve to update engineering education. Recent experience suggests an increased rate of change for the future. The fact that engineers have typically human needs and goals, and the fact that engineers respond to these in our free society, introduces a third class of problems. One approach to the solution of these problems is the unified engineering curriculum based on a core of subject mat-ter common to all engineering. Experience suggests that the unified curriculum is an effective method to minimize the importance of the first two problem areas presented, and shows a degree of success in handling some problems within the third area. Perhaps, for the good of all segments of society, it is best to have both career-oriented and unified curricula represented by educational institutions of high quality.

Jan 1, 1963

By M. L. Haider

Introduction I Appreciate very much the opportunity of discussing with you tonight oil developments in western Canada. These developments are of importance to all of us, first because of their great economic significance to all of Canada, and second because of the location of the new oilfields. Situated as they are in the west and northwest, they are of considerable strategic value from the standpoint of continental defence. The story of oil development in Canada covers a span of almost a century, during which time success in finding reserves of petroleum was barely sufficient to maintain interest in continuing the search. Finally, in 1947, a well of the first importance was completed in Alberta and, judging by discoveries made since then, it appears that Canada, at long last, is to become an important producer of petroleum.

Jan 1, 1950

By R. W. Nice

Presently about 60% of the world's nickel resources are tied up with lateritic ores while about 25% of the world's nickel is produced from sulphides. Based on this the industry has to focus on improving lateritic nickel economics in order to maintain the high use of the metal worldwide. In 1997 three junior mining companies in Australia organised finance against all odds and commenced development of three separate nickel and cobalt extraction plants treating lateritic nickel ores. All three projects utilise similar pressure acid leaching (PAL) technologies while each has unique metal recovery technologies All projects have experienced numerous processing and maintenance related difficulties such that full ore throughput has been reached by only one operation after five years. This shortfall in performance has caused the owners considerable angst and financial pain. In 2000 Cawse went into receivership and was purchased by an international corporation. Recently, Bulong also went into receivership and has undergone an orderly shutdown, awaiting sale to a new buyer. Murrin Murrin has settled with its financiers and is in a position to operate as planned for many years forward. This paper will discuss a number of the technical difficulties that affect the ore preparation, PAL and solution treatment circuits of these plants. The objective is to identify the cause of some of the difficulties and propose possible solutions so that the next generation of lateritic operations can emerge as technically and, more importantly, economic successes. A number of these process improvements have been identified by the existing operators and in many instances have been or are being implemented into the existing operations.

Jan 1, 2004

By B. W. Raymond, D. W. Zandee

"IntroductionCoal deposits are found in many regions in Canada and vary widely in their age, quality and rank. All classifications of coal except anthracite are found in significant quantities in this country.Deposits in the Maritimes are mainly bituminous; Lignite is found in Saskatchewan and Ontario and sub-bituminous coal in the plains region of Alberta. The Rocky Mountain coalfields of Alberta and British Columbia contain low and high-volatile bituminous coal and, in a few places, semi-anthracite. The British Columbia interior contains deposits of semi-anthracite, bituminous, sub-bituminous coals and lignite. The Yukon and Northwest Territories also contain substantial deposits of bituminous coal and lignite.Currently Nova Scotia produces both thermal and metallurgical coal, Saskatchewan produces lignite and Alberta produces both sub-bituminous and bituminous coal for thermal purposes. Large deposits of metallurgical coal are now being exploited in the Rockies arefl of British Columbia and Alberta by open pit methods. The raw coal is treated in large capacity preparation plants to remove refuse and upgrade the product to a consistent metallurgical quality with respect to ash, moisture, volatile matter and coking properties.The treatment of coal involves crushing, screening and cleaning by dense medium, jigs, water-only cyclones, tables and froth flotation to produce a diverse range of coal products differing in quality and size for various end uses.The chapter on Crushing and Screening Circuits was concerned mainly with crushing of metalliferous ores to produce a concentrate of one or more valuable minerals which normally constitute a small portion of the original mass of the material treated.Coal differs physically from ores in many ways such as lower specific gravity, relatively large volumes but low tonnage of product, and its habit of absorbing moisture requires extensive dewatering processes more complicated than settlement and filtration. Most significant, for this paper at least, is the fact that crushing coal is not as energy intensive and much smaller equipment is applicable.Crushing and screening of ores is intended to reduce the size of all constituents as quickly and efficiently as possible to allow liberation of the mineral particles. The crushing of coal is different in that the coal is not the minor constituent and the production of fines, in the initial stages at least, is highly undesirable. The basic objectives of crushing coal are the reduction of run-of-mine material to sizes suitable for cleaning or further reduction of coal to market sizes."

Jan 1, 1989

By H. R. Wilson

"This paper describes the evolution of the Waste Management Program at the Lupin Mine through the years 1982 - 1988. The program was developed in response to the terms and conditions of the Water Licence issued to the mine in 1981 by the Northwest Territories Water Board. Echo Bay Mines Lupin Mine is located on the western shore of Contwoyto Lake in Canada's Northwest Territories about 80 km. south of the Arctic Circle.The gold mine commenced production in 1982 and the Waste Management Program was based originally on the total containment concept. Due to an expansion of the mill circuitry and increased throughput, it was apparent that the total containment concept would require reevaluation since discharge from the pond would be required within a few years. During the initial years of production, an investigative program was established to determine the most effective means for treating the tailings pond water. This program incorporated both laboratory studies as well as monitoring of the tailings pond contents and environmental conditions as the impoundment area was filling. The program showed that natural degradation phenomena, if properly utilized, are effective in lowering the concentrations of all contaminants to within Licence limits with the exception of arsenic. To ensure compliance with arsenic limits, an iron salt was added to cause arsenic to precipitate from solution in the tailings pond.As a result of our studies, the tailings management system finally implemented at Lupin Mine includes the following components:Tailings pulp retention cells constructed by dyking off one end of the tailings impoundment area.Two tailings ponds in series operated in a sequential decant and fill fashion.An iron salt solution preparation and metering system.A syphon system into which the iron salt solution is injected as the contents of the first pond are decanted into the second pond.A second syphon system for decanting the contents of the second pond to the receiving streamThis paper discusses the findings and conclusions of the waste management investigative program, describes the civil work completed to reach our final operating scenario, describes the sequence of operating the treatment system, reviews performance data, and comments on abandonment and restoration of the tailings impoundment area."

Jan 1, 1989

By E. R. Lea

The B. M. & S. orebodies, consisting of the No. 6 (Brunswick) and the No. 12 (Anacn Leadridgz, have the distinction of being the first major 1base metal ore deposits to be found in the Province of New Brunswick. They are massive sulphide de-posits consisting of pyrite (pre-dominantly) and base metal sulphides, and they carry values in lead, zinc, copper, and silver. These orebodies are localized within favourable drag fold structures believed to be related in their origin to external forces set up in the area subsequent to the primary regional folding. Both orebodies are characterized by the presence of magnetite 'iron formation' which, in certain 'Portions of each orebody, may be found as relics within the massive sulphides. Studies show the magnetite to be the first metallic mineral within the ore ?zones, followed by pyrite, Sphalerite, galena, and finally chakopyrite. The shape of these massive pyritk orebod:es as well as the distribution of values within them is controlled to a large degree by the ore-ore drag fold structures. A possible relationship is discussed between the basic intrusives in the area ?and the magnetite deposits. It is suggested that a large portion of ?the iron content of the massive suplhedes has been derived from the earlier magnetite. Intermittent movements in the area during the sulphide mineralization are believed to belong to the last stages of deformation in the area. These late movements may have been caused by the intrusion of the granite into the area. The granite may have a genetic relationship to the B. M. & S. orebodies.

Jan 1, 1958

By A. Liem, R. L. Johnson, C. Sturgess, E. Kuzub

New challenges in mineral processing arise as high-grade ores become less available and the mining industry is forced to exploit lower grade ores. One of the challenges in beneficiating lower grade ores is the liberation of mineral particles while maintaining control over material management. Lower grade ores need fine grinding to free valuable minerals, but finely divided particles can cause severe problems, such as dustiness and flowability, in subsequent stages of material management. There are at least two approaches that can be taken to resolve this dilemma, both of which relate to particle size enlargement. First, the application of a dust suppressant can be used to control that aspect of material management. The optimal choice of dust suppressant agent depends on effectiveness and cost, both of which can be strongly influenced by the selection of application method. Second, agglomeration combining small particles into larger units-can reduce dust and improve the flow characteristics of the material at the same time. There are several mechanisms that can be employed to agglomerate mineral materials. Although agglomeration adds a new processing step, it is often cost effective. This paper describes these two approaches and their respective challenges, as they relate to a mined ore. We report on modified or newly developed procedures for characterizing mineral ores with respect to material management. On the same material, we use agglomeration processing to capture fines within larger particles and show how dustiness and other aspects of material handling are affected. We conclude by discussing their specific application in accordance with the mineral properties and processing needs.

Jan 1, 2004

By M. Feinendegen, Ph. Siebert, C. Clauser, K. Willbrand, M. Ziegler

"Three institutes of RWTH Aachen University collaborate on laboratory tests and numerical simulations of hydraulically driven fractures in igneous rocks. The project´s target is to enhance the understanding of hydraulic induced fractures for deep geothermal energy exploration. Based on the idea of creating new discrete fractures in hot dry rock (HDR) reservoirs, the current project stage deals with this process on a laboratory scale. Especially for this purpose, a new testing facility has been developed and laboratory tests are performed to verify a hydraulic fracture propagation code based on the extended finite element method (XFEM). The testing facility enables us to initiate and propagate fractures in large samples of dense rock under triaxial confining pressures and to monitor the fracture propagation by extensive measurements. This contribution gives a short introduction to the project‘s background and mainly focusses on the test facility, the experimental procedure and exemplary results.INTRODUCTIONThe most efficient technique to increase the permeability of subsurface rock is to initiate and open fractures by applying hydraulic pressure from a packed borehole-section and to inject fluid into these fractures to propagate them. Since its first use in petro industries to enhance the production of wells in natural gas and oil reservoirs, the interest in targeted creation of hydraulic fractures has increased exponentially. As the key technology to the extraction of unconventional gas from shale, hydraulic fracturing (HF) became a major topic in a heated public debate. Based on the fact that a fracture tends to propagate in a direction perpendicular to the minimal principal stress, hydraulic fracturing has become an established tool for estimating geological stress states in almost any depth. Enhanced geothermal systems (EGS) in HDR reservoirs use engineered fractures as a heat exchanging system for a cycling fluid driving a power plant."

Jan 1, 2015

By M. Hashemzadeh

The efficiency of water use is a top priority for the global minerals industry, especially in regions with limited freshwater supplies. In these areas, the freshwater shortage has prompted mining companies to search for alternatives to freshwater sources. Seawater has been proven to be a potential water source for mineral beneficiation and metal extraction processes. This study compares chalcocite leaching behavior with ferric chloride to that with cupric chloride. We carried out leaching tests with a highly pure chalcocite sample in jacketed reactors under fully controlled pH and solution potential. The effect of chloride concentration, oxidant concentration, and temperature on copper extraction was quantified in both cupric and ferric chloride systems. In the ferric chloride system, increasing ferric concentration showed a positive effect on the first stage of chalcocite leaching. In the second stage, increasing temperature markedly enhanced copper extraction. In the cupric chloride system, chloride concentration presented a considerable effect on both the first and second stages of leaching, while temperature had a remarkable effect only on the second stage. The findings of this study would be beneficial to mine operations aiming to replace fresh water with seawater for heap leaching of chalcocite. INTRODUCTION Mineral processing operations/plants are normally operated adjacent to mines which are often located in remote and arid area, such as northern Chile, southern Peru and Australia with limited access to fresh water (Liu, Moran, & Vink, 2011, 2013). Water scarcity in these areas has prompted mining companies to invest in sustainable technologies to reduce the water use and/or increase the water use efficiency. One of the current sustainable approaches in mineral processing operations is to replace fresh water with seawater. Seawater is now being increasingly used for mineral beneficiation and metal extraction processes (Hernández et al., 2015). Another application of seawater could be for heap leaching of copper secondary sulfides, mainly chalcocite. However, the high concentration of chloride ion in seawater may significantly affect leaching kinetics of copper sulfide concentrates and ores (Watling et al., 2014). Therefore, it is essential to develop a fundamental understanding of the leaching of chalcocite in chloride media.

Jan 1, 2019

By S. Markstrom

The Boliden AITIK copper mine is located 100 kilometres north of the Arctic Circle in northern Sweden. A pre-feasibility study was conducted in 2005 with the aim of increasing the capacity of the existing processing plant. After analysis, options to upgrade the existing plant were abandoned in favour of building a new processing plant, with higher capacity and therefore greater profitability. A new plant could be designed with greater flexibility to make potential future expansions easier. A feasibility study for a new 36 Mt/y processing plant including fully AG grinding circuits and flotation was completed in 2006. The project was approved by the Boliden board shortly thereafter. Construction started in the beginning of 2007 and was completed during 2009. Commissioning of the new plant was undertaken in the first half of 2010. The grinding circuit consists of two lines with each line consisting of a 22.5 MW AG mill and a 10 MW Pebble mill in closed circuit with a spiral classifier. The nominal production level is 2 200 t/h for each grinding line. This paper presents the start-up and operation of the grinding circuit.

Jan 1, 2012

By V. G. Papangelakis, J. E. Dutrizac, G. Azimi

A new model capable of predicting the solubility of calcium sulphate solid phases in zinc sulphate processing solutions from 25 to 95°C was developed. The model uses the Mixed Solvent Electrolyte (MSE) model of the OLI systems software to calculate the mean activity coefficients of the electrolyte species. The model was tested using recently developed experimental measurements. It was shown to predict accurately the solubility behaviour of calcium sulphate in multi-component zinc processing solutions containing ZnSO4, H2SO4, MgSO4, MnSO4, Fe2(SO4)3, Na2SO4 and (NH4)2SO4. The model can also explain the complex effect of coexisting metal sulphates on the solubility of the CaSO4 phases. The model is a practical tool for assessing the process chemistry of a wide variety of complex aqueous processing streams.

Jan 1, 2008

By C. Lara-Valenzuela, R. Perez-Garibay, F. López-Saucedo, A. Uribe-Salas, L. Magallanes-Hernandez

A relationship between gas dispersion parameters, namely gas rate (Jg), gas holdup (Eg), average bubble size (db) and bubble surface area flux (Sb), with the metallurgical performance (e.g., grade and recovery) has been established.. Results of eleven columns operating at five concentrators of Grupo Pefioles (Mexico), ranging between 1.52 to 3.35 min diameter and performing in the cleaning stages of lead and zinc circuits, are presented and discussed. The results showed that the effect of gas dispersion parameters was consistent and that both, Sb and Eg, correlate well with recovery particularly when the influence of feed pulp density is also considered.

Jan 1, 2009

By J. De Geoffroy, T. K. Wignall

The paper describes a statistical method based on regression and classification analysis which is designed to assist exploration management in the selection of prospecting areas and drilling targets in regional programs. The classification is based on three criteria which are formulated from sets of relevant geological, geophysical and geochemical factors: (a) regression estimates of expected ore values, (b) Bayesian probabilities of success and (c) expected utility payoffs. The advantages of the method are: (a) rational and unbiased ratings for areas or targets in a manner consistent with management's goals; (b) calculation of probabilities of success and confidence intervals for the ratings, and (c) rapid and accurate handling of a large amount of data by computer programs.

Jan 1, 1970

Cominco began investigations about ten years ago relative to noise abatement in underground operations. As a result of intensive research, this study has advanced so that the practice now has wide application. Automotive mufflers are used on vane-type blasthole diamond drills. Exhaust hoses are attached to longhole percussion drills. Hand-held drills, such as airlegs and stopers, are equipped with mufflers which are either part of the drill, as received from the manufacturer, or are light rubber de-vices developed, fabricated and installed by Cominco. Ear defenders are in general use. The paper reviews details of practices employed, and assesses the success achieved. Noise is generally associated with some of the basic equipment used in mining. About ten years ago, in order to improve on this situation. The Consolidated Mining and Smelting Company of Canada Limited began investigations relative to noise abatement in its underground operations. As a result of intensive research, this study has advanced to the point

Jan 1, 1964

Mercapto organic compound SDMP was used as a depressant for separation of copper activated marmatite from pyrrhotite in the presence of butyl xanthate. Flotation results show that SDMP has strong depressing effect on pyrrhotite recovery in the absence and presence of copper ion, but has promotional effect on marmatite recovery when added together with copper ion. The flotation test of mineral mixtures shows that copper-activated marmatite could be separated efficiently from pyrrhotite using SDMP as depressant. Infrared adsorption spectra demonstrate that SDMP has a strong adsorption on pyrrhotite surface through its functional groups such as ?SH, -S03.

Jan 1, 2006