Search Documents

By J. G. Debanne

MOST company-employed petroleum engineers have in their accounting departments punch-card computers that can perform engineering calculations thirty to three hundred times faster than desk calculators, or they can rent such machines from Computing Service centres. These machines not only eliminate the drudgery of desk calculation but also the risks of human errors. The I.B.M. t 604 punch-card computer of Texaco's accounting department in Calgary has been used for oil and gas property evaluations, curve fitting by least squares, statistical core analysis studies, unsteady-state water in-flux studies, phase equilibrium performance prediction of oil reservoirs, gravity segregation calculations, etc.

Jan 1, 1958

By D. S. Evans

Major Project Blues Over the last two decades, almost every major project has suffered significant cost overruns, significant schedule delays, and/or poor quality work. Exceptions are rare and most projects that tout being ?On Time and Under Budget? have re-cast schedules, significantly modified scope or revised base estimates. The problem isn?t new. In the late 1980?s the Rand Corporation published a study showing that 80% of all major projects had significant cost and schedule overruns. The problem is not restricted to the Canadian environment, or to a specific industry. It is a global problem.

May 1, 2013

By Zihe Ren, Edouard Asselin, Marcus Tomlinson, Tianbi Zhang, Jing Liu

"Raman spectroscopy is used to quantify the extent of disorder in the carbonaceous matter associated with preg-robbing ores. Previous studies of Goldstrike ores showed that the height and width of the peaks for the “D” (disordered) and “G” (graphite) bands, the so-called “Raman ratio” had a strong correlation to the preg-robbing value (PRV) measured for various ore samples. A brief literature review on Raman spectroscopy as it applies to preg-robbing ores is presented. Further, recent studies, presented here, have shown no correlation between the Raman ratio and the PRV for a wide variety of ores. This suggests that the extent of organic carbon crystal disorder is not the main factor in determining preg-robbing characteristics.INTRODUCTION Preg-robbing may arise from natural carbonaceous materials in the ore. Several mechanisms have been proposed in the past decades including a physical sorption process by the carbonaceous matter, or via the reduction of aurocyanide at the mineral surface (Abotsi & Osseoasare, 1986; Afenya, Osseoasare, & Abotsi, 1983; Tan, Feng, Lukey, & Van Deventer, 2005). Nevertheless, the mechanisms of preg-robbing remain poorly understood. Understanding the nature of the preg-robber is of practical importance for the selection of a suitable treatment process. Fine carbon particles in the ore have been recognized as preg-robbers due to their similarity to the activated carbon used in the carbon in leach (CIL) or carbon in pulp (CIP) processes. Previous research has illustrated that the activated carbon (also referred to as amorphous carbon in some literature) has a much higher absorption ability than pure graphite with high crystallinity (Adams & Burger, 1998). Adams et al (Adams, Swaney, Friedl & Wagner 1996) concluded that carbonaceous matter is largely responsible for the overall preg-robbing capacity of a given ore. However, the mechanism of carbon preg-robbing was still not clear mostly due to the complexity of amorphous carbon and its behavior in different solution matrices, and at different pH and temperature (Adams, 1990, 1993)."

Jan 1, 2017

By W. A. Jones

"The Hollinger gold mine is in the Porcupine area, Cochrane district, in northern Ontario. The adjacent town of Timmins, which has a population of 25,856, lies 490 miles by railway north of the city of Toronto.The property was staked in the late summer of 1909. The original four claims were staked by Benjamin Hollinger, after whom the mine was named. Development commenced in the autumn of 1909 and mill construction in the winter of 1910. A catastrophic forest fire swept the district in 19ll, destroying the surface plant, so that the original 300-ton mill was not completed until June 1912. From that date up to December 31, 1945, 44,280,750 tons of ore have yielded 13,636,796 oz. gold and 2,613,354 oz. silver. The total value of the production has been $363,638,315.0REBODIES AND MINERALIZATIONThe orebodies consist of quartz veins, stringer lodes, and scockworks, with associated pyritized wall-rocks. The width of individual orebodies, as exposed by mining operations, ranges from 1 to 70 feet and averaged approximately 10 feet in 1942. The vein system forms a complex pattern in a favourable zone, which in places is 6,000 feet long and 4,000 feet wide. The deepest level being developed is 5,150 feet below the surface. Few veins are persistent for long distances, although some are continuous for more than 1,000 feet longitudinally and vertically.The host rocks consist of a closely folded series of Precambrian lava flows of Keewatin age. These are schistose and hydrothermally altered, but are believed to have originally been of intermediate to basic composition. The schistosity strikes N.70°E. and dips to the south at 75° to 80°. The structure of the formations is complex, but in the principal ore-bearing zone the general dip of the flows is to the south at a slightly flatter attitude than the schistosity."

Jan 1, 1954

By George E. Cole

Introduction In view of the fact that, during the past year, two Manitoba mines-Flin Fion and Sherritt Gordon-have entered the list of producers and have materially increased that Province's contribution to the metal production of the Dominion, it would seem appropriate at this time to review the progress of the industry in the Province, with particular reference to the out-standing metal-mining developments of the past decade. That these two mines have been able to continue their operations in spite of the low prices of copper and zinc adds a touch of brightness to the industrial life of the Province. Depression in metal prices is not encouraging to the mining industry, but it does stimulate efficiency in methods and costs of production. As two thriving towns have grown around the two mines, the will of the management to carry-on is of great consequence to Manitoba, this year so hard hit by the .agricultural depression. And, much as it is a pleasant feature in the mining situation that these mines have been able to continue operations, nevertheless it must be noted, in reviewing the mining developments of the past few years in Manitoba, that the Province was fortunate enough to profit by good times, in that an industry was established which gives evidence of permanency. In the metallic field, the section of Manitoba that first received attention from prospectors was the boundary district, west of the Lake of the Woods. Several claims were staked here at the time of the gold boom in the neighbouring Ontario area. But the first real interest in metalliferous deposits dates from the discovery of gold in March, 1911, in quartz veins on the shores of Rice lake, some twenty miles east of lake Winnipeg. Systematic and organized prospecting of the pre-Cambrian areas of the Province may be said to have commenced with that discovery. The first gold discovery in northern Manitoba was made at Wekusko (Herb) lake in 1914. This was followed by the discovery of the Flin Flan and Mandy copper ore-bodies in 1915 on Flin Fion and Schist lakes, respectively.

Jan 1, 1932

By J. Stiksma, R. Kalanchey, M. J. Collins, G. Owusu, R. Raudsepp, K. R. Buban, L. A. Barta, L. Masters

This paper describes the results of testwork for the treatment of Ambatovy laterite by an acid pressure leach process, with recovery of the soluble nickel and cobalt values as mixed sulphide intermediate by precipitation with hydrogen sulphide, and subsequent refining of the mixed sulphide to nickel and cobalt metals. These process development studies were carried out primarily in 2004, as part of a bankable feasibility study for the Ambatovy Nickel Project.

Jan 1, 2004

By T. L. Sadlier-Brown, Andrew E. Nevin

"Common properties of commercial geothermal steam reservoirs are a magmatic heat source, the presence of water in vapour and liquid phases, and a surrounding seal of low permeability. The latter may be due to a combination of hydrologic load, argillic alteration and mineral precipitates. The temperature and pressure of vapour and liquid co-existing in equilibrium at maximum enthalpy may approximate 451°F and 450 psi. Steam reservoirs do not necessarily vent steam, but fluid which breaches and mixes with meteoric waters may emerge as hot springs. A systematic exploration program in Western Canada would involve a sequence of four stages utilizing geological, geochemical and geophysical techniques. The geochemical parameters of hot spring waters, such as silica, lithium and potassium content, give some indication of the basic reservoir temperature. The geology of Quaternary volcanics, including reservoir rocks, structure and rock alteration, is of prime importance. The costs of preliminary indirect methods are no more than those of oil and gas exploration; however, high temperatures compound drilling problems and costs. Exploration expenditures of twenty million dollars or so might be needed for a significant discovery. British Columbia and the Yukon Territory contain abundant Cenozoic volcanic rocks and over 50 thermal spring complexes (some with as many as 20 springs in one complex). Six regions are tentatively picked for exploration. Four regions coincide geographically with post-1980 electric power facilities and loads, and with possible alternatives such as potential dam sites. The Lillooet River region, Terrace region and Western Vancouver Island region have inferred potential for the existence of a plus-500-Mw geothermal reservoir. The Kootenay region may or may not have such potential. The Stikine River region has strong evidence of geothermal endowment, but the anticipated power market of the middle future might be only 30-50 Mw. The Whitehorse, Y.T., and Atlin, B.C., region has a belt of thermal springs and Recent cinder cones. The anticipated middle-future needs are real enough, but in absolute terms they are small, say 20-30 Mw. Legislation and policy on geothermal resource rights are lacking in British Columbia and the Yukon Territory at this time. As well as making policy, governmental organizations will play a significant role in geothermal development as buyers of steam or electricity. The role of industry is visualized as assuming the high-cost and high-risk exploration effort, provided the nature of this effort is understood by government."

Jan 1, 1973

By Larry Urbanoski

"This paper describes the application of a radioisotopic energy dispersive X-ray aY1alyser to complete on-stream analysis in a base metal concentrator.The major components of the system are outlined and some description of the application, operating experiences and benefits are provided.IntroductionThe ma1n intent of this paper is to describe the on-stream analysis system in operation at the Geco concentrator. X-ray analysis systems installed in Canadian concentrators to-date may be broadly classified as wavelength dispersive analysers whereas the installation described herein is an energy dispersive x-ray analysis system. Energy dispersive x-ray analysis techniques may utilize radioactive sources to provide primary x-rays for excitation of elements and separate the secondary x-rays on the basis of energy levels. In contrast wavelength dispersive analysers apply high voltage x-ray tubes to provide primary x-rays and utilize crystals to disperse and thereby separate x-rays generated by bombardment of the sample."

Jan 1, 1978

By J. Beddoes

The various microstructural factors that influence the creep resistance of y-titanium aluminides are presented and discussed. Titanium aluminides have potential for a variety of intermediate temperature applications in both gas turbine and reciprocating engines. While it is well established that the 'fully lamellar' titanium aluminide microstructure offers superior creep properties, the particular influence of lamellar morphology, third phase precipitation, and grain boundary structure in controlling both the primary and tertiary creep behaviour is presented. The results are primarily based on tensile creep experiments undertaken using several titanium aluminide intermetallic compositions processed via powder metallurgical techniques, investment casting and Bridgman directional solidification. The results indicate that lamellar structure and precipitate formation have a major impact on primary creep, while microstructural degradation through both lamellar and precipitate coarsening influence on the onset of tertiary creep leading to fracture. The results are used to design a creep resistant microstructure produced by directional solidification and the effectiveness of this designed microstructure is demonstrated through 10,000 hour creep tests.

Jan 1, 2004

By W. Yang, R. Rajasingam, K. Mohanarangam

"Copper Electrowinning (EW) is a complex electrochemical process that involves the production of LME grade copper from copper rich electrolyte. The process involves the deposition of the copper ions onto the cathode from copper rich electrolyte with the production of oxygen bubbles at the anode. The process setups up a complex flow pattern within the cell as it is subjected to varying density gradients due to the deposition process along with oxygen bubble driven flow. It is a necessity to understand and quantify the flow behaviour within these cells in order to maintain the production of highest grade copper. In fact, the oxygen bubbles originating from the process is responsible for the generation of acid mist which is a designated as a carcinogen a major health hazard around EW tank houses. Hydrodynamic assessment of the process has so far been restricted to simple mass balances and some limited numerical modelling. All the models are based on assumed boundary conditions which has not so far been verified by any real-time physical measurement. This apparent gap has led to models which could not be directly used to track process changes or troubleshoot problems in EW tank houses. In order to address this gap, CSIRO has established a full size (width and height) transparent cell capable of simulating plant operating conditions (across the range currently used). With the use of sophisticated diagnostic analytical tools and measurement techniques it was possible to study all the operating variables (current density, flow rate, temperature, etc.) independently and their effect of bubble size, bubble velocity, gas hold-up as well as acid mist generation and its size. In order to address safety concerns in tank houses around acid mist early results outlining the factors contributing to its generation as well as the effect of various barriers to mitigate acid mist is outlined below.INTRODUCTIONA significant part of today’s copper production is through hydrometallurgical route which predominantly involves leaching, Solvent eXtraction (SX) followed by ElectroWinning (EW). Producing copper using this approach have shown to be environmentally friendly (Dresher, 2001) compared to the traditional smelting process. EW is the final step in the production of LME grade copper using the hydrometallurgy route. The electro-chemical process involves the use of a lead anode (Pb-Sn-Ca) and a stainless steel cathode to produce copper sheets using the copper rich electrolyte from the SX process and with the applications of direct current to the electrodes. This electro-chemical reaction results in the deposition of copper ions on the cathode with oxygen released from the anode as a by-product. Hydrodynamically, the oxygen bubbles create a bubble driven flow within the EW tanks with the surrounding electrolyte. A direct result of this could be seen from the quality of the copper deposited on the cathode. Most of the copper plates produced from the traditional tank houses have a rough texture at its bottom one-third while the top two-thirds have a smooth finish with a finer grain structure."

Jan 1, 2016

By N. Bahrani

Knowledge of the state of stress in the Earth?s crust is very important to the safe and efficient development of underground excavations in mining and civil engineering projects. A number of methods have been developed over the past 40 years to assess the stress field in the rock mass. These range from local estimates derived from compilation of regional stress databases to back-analysis of field observations to dedicated in situ measurements. The Geomechanics Research Centre (GRC) at MIRARCO has a long history of undertaking in situ stress characterization and measurement. In this paper, the stress measurement techniques used by the GRC, including overcoring and undercoring in addition to borehole breakout back-analysis, are briefly reviewed. The limitations and application of each technique for different ground conditions and the challenges involved during the field work and in interpretation of the results are discussed. A successful stress measurement campaign is not limited to acquiring valid local measurement, but must include a careful interpretation and integration of the measurement with other geological and geotechnical context information. Based on our experience, it is suggested that all available stress indicators and data are combined and integrated with the local geological and geomechanical conditions to derive a consistent stress characterization for a given site.

Aug 1, 2013

By Alan E. Renshaw

"This paper is a practical overview of ways to reduce cost in the design and operation of an Arctic mine. The economically important issues of the Arctic mine that will be addressed include: permafrost and the active zone in general terms; road building in and over permafrost; Arctic geotechnical mine design considerations; pit dewatering techniques in sub-zero temperatures; and blasting frozen materials with techniques to obtain optimal results. A final section on a few special topics conclude this paper.Although this paper primarily refers to near surface conditions more closely associated to an Arctic surface mine, many of the ideas and techniques contained in the paper also apply to the surface construction of an Arctic underground mine."

Jan 1, 1996

By I. Thobadi, C. Pawlik, K. Bisaka, S. Mokoena, M. Erwee

The PyEarth™ process developed at Mintek has been demonstrated successfully at pilot scale. Nine tons of ore containing 2.3 mass % of total rare earth oxides (TREO) from a dormant mineralogically complex iron-rich ore deposit, was subjected to a concentrating smelting step in a 200 kW DC open-arc pilot furnace and the rare earths from the resulting slag were extracted via a hydrometallurgical route. This ore deposit is practically not amenable to extraction by conventional methods. The testwork results proved that the PyEarth™ process was able to optimize the extraction of rare earths while minimizing waste through the removal of iron as a saleable iron alloy. Reduction of iron to the alloy in the smelting step was found flexible, efficient, and controllable, while rare earths were left virtually unreduced in the slag phase. The slag chemistry is selected to optimize both the smelting and leaching performances as well as the alloy composition. Leaching of the resulting slag was found possible and most efficient in hydrochloric acid amongst other lixiviants tested.

Jan 1, 2017

By V. Silins, J. Tameling, R. C. Cook

"A general review of the wear problems encountered in the mining industry is presented and current practice for wear protection systems is reviewed.A new concept in wear protection is described and compared to alternative systems. Utilization of conventional stud welding technology and abrasion-resistant wear studs is shown to be a useful supplement or substitution for conventional techniques. Operating life of many consumable components can be increased by up to four fold. The technique is highly portable for on-site field application or can be used in shop environments.Details of the wear protection model and metallurgical properties of the wear component are also reviewed. Laboratory wear test data are reported to supplement field test performance or to screen potential alloy compositions for application in specific environments.A Review of Wear Problems and Wear ProtectionThe emphasis on wear protection has increased in recent years because of the increasing impact of the potential savings in time, materials and energy. A 1974 German study concluded that attention to tribology, the study of friction and wear, could save approximately $3 billion, and a study in the U.S.A. at the same time put the figure at $100 billion of which $20 billion was for materials. A more recent American study put the energy component of the potential savings at $16.2 billion per year. A recent British study estimated the total potential savings in the U.K. as $1 billion per year, with the largest savings coming from lower maintenance and replacement costs ($500 million), lower breakdown costs ($250 million) and increased machinery life ($200 million). These three major contributions are all potentially accessible in the mining industry."

Jan 1, 1982

By Dave Thomas

?Uranium is a common trace metal at the earth?s surface, but these are amazing super-high grade (up to 25%) pods, veins and disseminated uraninite (UO2) near unconformities between Proterozoic siliciclastic red beds and metamorphic basement with graphitic metapelite and radiogenic granite. ?Pitchblende fills extensional features in reactivated fault zones and replaces matrix in sandstone ?One mining district in Canada ?the Athabasca Basin ->30 deposits /prospects -most in eastern ¼of basin -produces 1/3 of world?s U -employs northerners -VERY high tech -VERY high safety standards Unconformity-associated uranium depositsUnconformity-deposits

May 1, 2006

By A. M. Gaudin

Introduction The discovery of artificial radioactivity, that is, of radioactivity of acorns other than those which are naturally radioactive, has increased vastly the possibility of using radioactivity as an analytical cool. The incomparable value of radioactive atoms, which are commonly termed tracers, arises from the extreme sensitivity of this analytical method. To get an idea of this extreme sensitivity it may be useful co recall that gravimetric analytical methods will not permit the weighing of anything much lighter than one-hundredth of a milligram of material. Under the most favourable circumstances, this represents an uncertainty in the answer of 1016 acorns, or 10,000,000,000,000,000 acorns. Accurate spectrographic methods possibly have a sensitivity 10,000 times greater than this, but the uncertainty is still of the order of 1012 atoms. The tracer permits ascertainment of decay of a single atom so that its sensitivity, without half trying, can be several orders of magnitude greater than that of any other method available co chemists. In addition co the sensitivity of tracers to which reference has just been made, tracers have another property which makes them unique. A radioactive atom is almost exactly like the corresponding non-radioactive acorn m regard to its electronic structure, and therefore in regard to its chemical properties. The nucleus is different, but the nucleus does not participate in chemical reactions. Therefore, a tracer acorn behaves like an ordinary atom until such time as its nucleus undergoes a catastrophic decay. This unique property permits one to use tracer acorns as atomic spies and therefore to follow the behaviour of acorns of a certain kind among their own kind. In other words, the tracer method permits us to study and measure what we call self-diffusion. All of the uses of tracers that have been made depend on the two properties co which reference has been made.

Jan 1, 1949

By S. S. Burns

"AbstractShovels of 18 cubic yard capacity and larger are described which incorporate advanced technology and techniques providing performance and operation tailored to meet the needs of open-pit mining.To achieve the goal s of increased production at lower cost with consideration of maximum availability, lower energy consumption per ton and low •impact on pit power, Harnischfeger Corporation developed a solid -state drive system (""Electrotorque"" - P&H trademark) and applied unique transmission methods.To date, more than 250,000 hours of experience in different parts of the world under varying operating and environmental conditions has proven that the ""Electrotorque"" shovel is the shovel of the future, today.This paper will discuss the electrical features and touch briefly on some mechanical features.Introduction to ""Electrotorque""THE hoist, crowd, propel and swing machinery of an electric mining shovel are driven by direct-current motors.A D.C. motor is used instead of an A.C. motor because the torque output per ampere input is at a maximum and the fact that it is doubly-fed (armature and field ) provides optimum flexibility in control.The power that is available in the pit is alternating current power. It is therefore necessary to change or convert this A.C. power to D.C. power so that the D.C. motors can be used."

Jan 1, 1977

By Paul A. Glapa

Quality is much more than providing a product that functions properly. True quality is a way of thinking, a way of doing business, and, ultimately, a way of satisfying a customer?s long-term needs. A true commitment to quality requires a top-down management commitment, with a willingness to change what needs to be changed and to expand upon ?best practices? that are already done well. Is there a cost to creating and maintaining a quality program? Of course there is, but the cost of not having a focused program is much greater. We have come to regard quality as an investment that pays dividends to both the supplier and customer. The lack of quality costs everyone and the customer pays the ultimate penalty. With modern, highly engineered surface mining equipment the end user calculates cost in terms of lost production (revenue), not simply the cost of the part. Bucyrus International, Inc. is a company that has listened to its customers and has dedicated itself to implementing an advanced quality program. The ultimate goal being the creation of a high quality product with extended reliability for the customer. The result is reflected in Bucyrus? current product offerings and highlighted by the new 495HF electric rope shovels at Albian Sands mine.

May 1, 2003

By Colin E. Dunn

Abstract-Plants have a remarkable ability to select, use and store metals derived from the substrate. Each species is unique in its requirements for and tolerances to the full spectrum of chemical elements in the Periodic Table. Studies to define the chemical characteristics of common trees and shrubs of the temperate forest are providing insight to their use for exploration, i.e., biogeochemical exploration. Examples of surveys over gold deposits in British Columbia show the effectiveness of sampling various tissues from different species in a range of biogeoclimatic environments. At the Nickel Plate mine in the Montane-Spruce zone, outer bark of Lodgepole pine was effective in defining a large area of metal enrichment; at the Carolin mine in the zone of Coastal Mountain Hemlock, analysis of twigs of western hemlock and Pacific silver fir provided an exploration target considerably larger than that defined by lithogeochemistry; at the Mount Washington gold deposit in the Mountain Hemlock zone, twigs of mountain hemlock and rhododendron were used to outline the mineralization; and in the Interior Douglas-fir zone at the QR deposit analysis of Douglas-fir tops collected by helicopter provided a rapid and effective method of identifying a gold-rich area.

Jan 1, 1995

SOME months ago a Committee on Deep-level Mining was appointed [by the Government of the Union of South Africa] to consider the possibility of gold mining being carried on at a depth below 8,500 feet. The Committee consisted of Sir Robert Kotze (Chairman) , Mr. H. S. H. Donald (Government Mining Engineer), and Mr. H. R. Hill. The Committee has now made a report which was tabled in the House of Assembly on March 1st. The Committee reported that the tonnage of ore locked up in the deep level areas of the Central Witwatersrand is enormous, and in the 30 miles between Roodepoort and the East Rand Proprietory Mines has a value of about £200,000,000. The Committee says that, with good ventilation, the present system of wet mining, possibly with some modification and with the aid of refrigeration, may be carried to 10,000 feet, but that greater depths will require the adoption of dry mining. "A vigorous campaign of practical experiment into the possibility of dry mining should be initiated, and the Committee recommends to the Government the appointment of a committee of experts, consisting of representatives of the mining industry, the Mines Department, and the medical profession, with the Government Mining Engineer as chairman. The Committee suggests the provision of £30,000 for the first year for the investigations and experiments contemplated, which could best be carried out by an organization which might be styled 'The Rand Mining Research Institute' and constituted somewhat on the Jines of the South African Institute for Medical Research" . The Committee suggests that this committee of experts should arrange for experiments to be made with dry mining in one of the deepest mines, and investigate ventilation, refrigeration, support of workings, and the physiological problems connected with mining. "We emphasize the necessity of treating this whole question as one of importance and urgency. The investigations should be prosecuted with the utmost vigour and should not be delayed at any time for want of funds or for any other reason. If they are not done thoroughly and quickly, the whole scheme might just as well be left severely alone.

Jan 1, 1945